Are your eyes bleeding? You can always change your theme.
0 Members and 1 Guest are viewing this topic.
Finally got around to unboxing this thing. Mine came with a few blemishes I'll need to contact Senter about, but overall, it's a really nice board. The brass plate and weight really make this feel super solid.Show ImageShow ImageShow ImageShow ImageDoes anyone else have these weird circle marks on the leaf?Show Image
Quote from: r4bbl3d4bbl3 on Fri, 17 May 2019, 14:11:46Finally got around to unboxing this thing. Mine came with a few blemishes I'll need to contact Senter about, but overall, it's a really nice board. The brass plate and weight really make this feel super solid.Show ImageShow ImageShow ImageShow ImageDoes anyone else have these weird circle marks on the leaf?Show ImageYeah, I have these marks and the light scratch marks under the weight on the back
Got it put together! Does anyone know if there is a reset built into the default keymap, or has my eagerness screwed me to take it apart again?Show ImageSent from my Pixel 2 using Tapatalk
Quote from: thearctican on Sat, 18 May 2019, 17:30:13Got it put together! Does anyone know if there is a reset built into the default keymap, or has my eagerness screwed me to take it apart again?Show ImageSent from my Pixel 2 using TapatalkWell I was going to say the reset is Fn+Esc but I think the default Fn key is where RWin should be and you're on a winkeyless build... At least it was for me on the hotswap PCB. Not sure if there's another Fn key mapped somewhere.
Quote from: thearctican on Sat, 18 May 2019, 17:30:13Got it put together! Does anyone know if there is a reset built into the default keymap, or has my eagerness screwed me to take it apart again?Show ImageSent from my Pixel 2 using TapatalkTry these methods in the "Put your keyboard into DFU mode" section. https://beta.docs.qmk.fm/newbs/newbs_flashingThe space+b and unplug method worked for me.
Quote from: Nostril on Sat, 18 May 2019, 17:56:00Quote from: thearctican on Sat, 18 May 2019, 17:30:13Got it put together! Does anyone know if there is a reset built into the default keymap, or has my eagerness screwed me to take it apart again?Show ImageSent from my Pixel 2 using TapatalkTry these methods in the "Put your keyboard into DFU mode" section. https://beta.docs.qmk.fm/newbs/newbs_flashingThe space+b and unplug method worked for me.That's what I needed. Fingers crossed they included bootmagic in the default build.Sent from my Pixel 2 using Tapatalk
Can confirm space+b when plugging in works for the hotswap PCB for DFU mode.Anyone know if these LEDs are RGB? if so, how to use that functionality in QMK (through code)?
Quote from: Nostril on Sat, 18 May 2019, 17:56:00Quote from: thearctican on Sat, 18 May 2019, 17:30:13Got it put together! Does anyone know if there is a reset built into the default keymap, or has my eagerness screwed me to take it apart again?Show ImageSent from my Pixel 2 using TapatalkTry these methods in the "Put your keyboard into DFU mode" section. https://beta.docs.qmk.fm/newbs/newbs_flashingThe space+b and unplug method worked for me.I tried all of these do you know if there are any other methods?I flashed a keymap without a reset key and now I can't seem to figure out how to the pcb back in DFU mode.
Fn + Esc while the keyboard is plugged.
Quote from: LuiKang on Sun, 19 May 2019, 00:52:46Fn + Esc while the keyboard is plugged.Afaik that only works because the default key map has a reset key on layer 1. The key map I flashed doesn’t have that unfortunately. My question is if there are any other key combos to reset or will I have to short certain pins on the pcb?
Quote from: spyruf on Sun, 19 May 2019, 00:59:50Quote from: LuiKang on Sun, 19 May 2019, 00:52:46Fn + Esc while the keyboard is plugged.Afaik that only works because the default key map has a reset key on layer 1. The key map I flashed doesn’t have that unfortunately. My question is if there are any other key combos to reset or will I have to short certain pins on the pcb? Thanks! That worked. Yes. There are no physical reset buttons on the PCB but you can contact the RE pin with the GND on the PCB. There are two RE pins near the MCU. Either one should work.
Quote from: spyruf on Sun, 19 May 2019, 00:59:50Quote from: LuiKang on Sun, 19 May 2019, 00:52:46Fn + Esc while the keyboard is plugged.Afaik that only works because the default key map has a reset key on layer 1. The key map I flashed doesn’t have that unfortunately. My question is if there are any other key combos to reset or will I have to short certain pins on the pcb? Yes. There are no physical reset buttons on the PCB but you can contact the RE pin with the GND on the PCB. There are two RE pins near the MCU. Either one should work.
These are the pins that you can jump to reset the board. The far right RE (both pins) and the G on the VOG. Use tweezers or paper clips. When it is plugged into QMK, jump before you flash and it should work. (Attachment Link)
Yes. There are no physical reset buttons on the PCB but you can contact the RE pin with the GND on the PCB. There are two RE pins near the MCU. Either one should work.
Show ImageShow ImageShow ImageLeaf 80, Holy Chickies, XDA Oblique (waiting for GMK Minimal)Leaf 60, Orange Alps, Japan AEK KeycapsLeaf 60, Gateron Linjar, GMK 9009
Has anyone found the same sized bumpons but clear online anywhere?
@thearctican @ArchDill I have implemented Bootmagic Lite, so the escape key will work as a reset while you're plugging in.
Anyone heard or got a pm from Senter recently?
Anybody else's weight kinda wobbly? It seems like even after I completely tighten the weight screws, there is still wiggle room for it.
Quote from: geewizwow on Mon, 20 May 2019, 09:34:54Anyone heard or got a pm from Senter recently?Wrote him 5 days ago because I got the wrong plate color. No answer until now.
Quote from: Sinapanis on Mon, 20 May 2019, 20:00:21Anybody else's weight kinda wobbly? It seems like even after I completely tighten the weight screws, there is still wiggle room for it.Yeah mines like that too. It's not terrible so I figured it wasn't a big deal.
Quote from: geewizwow on Mon, 20 May 2019, 09:34:54Anyone heard or got a pm from Senter recently?Quote from: befbef on Mon, 20 May 2019, 11:11:51Quote from: geewizwow on Mon, 20 May 2019, 09:34:54Anyone heard or got a pm from Senter recently?Wrote him 5 days ago because I got the wrong plate color. No answer until now.Oh, I missed your message. A reply is coming.
Quote from: reidd on Mon, 20 May 2019, 21:01:20Quote from: Sinapanis on Mon, 20 May 2019, 20:00:21Anybody else's weight kinda wobbly? It seems like even after I completely tighten the weight screws, there is still wiggle room for it.Yeah mines like that too. It's not terrible so I figured it wasn't a big deal.Quote from: Sinapanis on Mon, 20 May 2019, 20:00:21Anybody else's weight kinda wobbly? It seems like even after I completely tighten the weight screws, there is still wiggle room for it.I guess the screws were not tightened enough due to the e-coating in the screw holes. It was a common issue with e-coating. You can remove the coating with an angle tip tweezer then try to tighten the screws again. I noticed this issue as early as in the Leaf 80 GB. In this GB, some of the screw holes were blocked before E-coating. Some are not for various reasons. Now as we've learned how to do it, all the screw holes in future E-coating cases will be blocked properly. I'm sorry for the additional confusions and the troubles you got in this GB.
has anyone tried to add underglow strips?
Quote from: yemeisong on Sun, 19 May 2019, 04:56:26has anyone tried to add underglow strips?Also looking for this answer, I want to add unnecessary RGB to all my stuff plz