Are your eyes bleeding? You can always change your theme.
0 Members and 1 Guest are viewing this topic.
I feel like a cottonheaded ninnymuggins for asking... but are you supposed to break away the middle parts of the diffuser? I'm assuming you do since I see no way to make it fit otherwise, but Ima scared to do eeet.
Thanks! (Attachment Link)
some of my keys are not registering on my m65a pcbspecifically 3, E, D, C, H, and Lis my pcb bad?
Quote from: froydroyce on Sat, 08 December 2018, 15:29:21some of my keys are not registering on my m65a pcbspecifically 3, E, D, C, H, and Lis my pcb bad?Is it built or unbuilt? Photos?
I would think that would cause switches around the stabilizers to be not working. These seem further away. Did you test by shorting with tweezers on the back of those switches?
Quote from: froydroyce on Sat, 08 December 2018, 15:29:21some of my keys are not registering on my m65a pcbspecifically 3, E, D, C, H, and Lis my pcb bad?Are you testing via Bootmapper Client directly? Could be they just aren't programmed currently.
Quote from: pixelpusher on Sat, 08 December 2018, 16:49:37I would think that would cause switches around the stabilizers to be not working. These seem further away. Did you test by shorting with tweezers on the back of those switches?i did. the said keys are not registering with tweezers. strangely, a lot of the other keys, when i smoke test them with tweezers, the key above it also registers at the same time
Quote from: froydroyce on Sat, 08 December 2018, 16:52:40Quote from: pixelpusher on Sat, 08 December 2018, 16:49:37I would think that would cause switches around the stabilizers to be not working. These seem further away. Did you test by shorting with tweezers on the back of those switches?i did. the said keys are not registering with tweezers. strangely, a lot of the other keys, when i smoke test them with tweezers, the key above it also registers at the same timeI will when I get home from work. Already late trying to troubleshoot lolYeah, that's a short if they are registering other keys. Did you test it before building? I don't know about conductivity of lube. Maybe there's a glop of solder somewhere? Can you take photos?
Quote from: froydroyce on Sat, 08 December 2018, 16:52:40Quote from: pixelpusher on Sat, 08 December 2018, 16:49:37I would think that would cause switches around the stabilizers to be not working. These seem further away. Did you test by shorting with tweezers on the back of those switches?i did. the said keys are not registering with tweezers. strangely, a lot of the other keys, when i smoke test them with tweezers, the key above it also registers at the same timeYeah, that's a short if they are registering other keys. Did you test it before building? I don't know about conductivity of lube. Maybe there's a glop of solder somewhere? Can you take photos?
Ended up being a mis-soldered leg on the MCU lolthank you all for your help, I greatly appreciate it!(family photo attached )
Quote from: froydroyce on Mon, 10 December 2018, 13:11:58Ended up being a mis-soldered leg on the MCU lolthank you all for your help, I greatly appreciate it!(family photo attached )Great. Glad you got it fixed. I have had to do that with 2 boards but I hate to recommend it bc you could ruin it if you don’t know what you’re doing.
So I just tried flashing a hex file that was too large and now my board wont turn on. I can't get it back into bootloader/reset mode by holding left ctrl anymore. Is my pcb bricked? or is there a way to fix this lol
Quote from: froydroyce on Tue, 11 December 2018, 23:51:25So I just tried flashing a hex file that was too large and now my board wont turn on. I can't get it back into bootloader/reset mode by holding left ctrl anymore. Is my pcb bricked? or is there a way to fix this lolI think you may have overwritten the boot loader (which can be fixed).Does it show up as an "Unknown Device" in Windows?Also, which PCB did you get?
Quote from: MajorKoos on Wed, 12 December 2018, 09:25:41Quote from: froydroyce on Tue, 11 December 2018, 23:51:25So I just tried flashing a hex file that was too large and now my board wont turn on. I can't get it back into bootloader/reset mode by holding left ctrl anymore. Is my pcb bricked? or is there a way to fix this lolI think you may have overwritten the boot loader (which can be fixed).Does it show up as an "Unknown Device" in Windows?Also, which PCB did you get?Yes it does show up as an unknown deviceit is the m65a pcb (v32a)
he's pretty responsive to both emails and even pms through geekhack
How are replacements handled? I just plugged in my black LZ CLS ms, and after 5 minutes I got the windows hardware disconnect sound, no more typing registered, I replugged it (got the disconnected and then reconnected system sound), and then it started to smell funny. So I immediatly unplugged and there was literally smoke coming out of the Mini USB port Got some fresh air in the room and then took a pic of what seems to be the culprit, this is a m65a PCBShow Image
(Attachment Link) (Attachment Link) Cerakoted CLSms
Quote from: Helldrop on Thu, 25 April 2019, 10:01:23 (Attachment Link) (Attachment Link) Cerakoted CLSmsthat looks fantastic. Where did you have it cerakoted?
does anyone dơne keymapping with x268v2 pcb? i could not fiund any json file from qmk config ....
I was struggling with this qmk config online. Im picking ISO layout, every functions work well except the \| was setup at the Backspace, that i could not change from \| to backspace in advanced. Been rekeymap and flashing many times but still not change at this one.