Post by: Ramiel on Fri, 13 July 2018, 08:05:04
I harvest most of the parts from a Niz TKL RGB keyboard including the PCB, sliders, slider housings, springs, controller. Then I designed a housing with a custom top-mounted plate.
(https://i.imgur.com/17kKSF1.jpg)
(https://i.imgur.com/MuKZqVq.jpg)
(https://i.imgur.com/ppI9rub.jpg)
(https://i.imgur.com/TB2H8es.jpg)
(https://i.imgur.com/xa580Gx.jpg)
(https://i.imgur.com/alORXvf.jpg)
Post by: Ramiel on Fri, 13 July 2018, 08:05:31
(https://i.imgur.com/k1CmkB5.jpg)
(https://i.imgur.com/2N3YRS1.jpg)
(https://i.imgur.com/70YRPHS.jpg)
MacBook style rubber feet
(https://i.imgur.com/ptjr2sz.jpg)
Niz keyboard controller
(https://i.imgur.com/JY2r2YV.jpg)
The main controller is connected with a custom PCB with USB C female connector
Post by: Ramiel on Fri, 13 July 2018, 08:05:47
Niz TKL keyboard PCB
(https://i.imgur.com/iKb2CBA.jpg)
(https://i.imgur.com/4gidcZi.jpg)
Rubber domes I bought from Niz
(https://i.imgur.com/v5WmCFN.jpg)
(https://i.imgur.com/FAvEexq.jpg)
(https://i.imgur.com/QdZ6qnN.jpg)
(https://i.imgur.com/6n55vDa.jpg)
Post by: mech0nly on Fri, 13 July 2018, 08:10:20
Sent from my iPhone using Tapatalk
Post by: CarterH on Fri, 13 July 2018, 08:10:49
Post by: wixxzblu on Fri, 13 July 2018, 08:11:45
Post by: LightningXI on Fri, 13 July 2018, 08:17:39
Sent from my mobile using Tapatalk
Post by: Ramiel on Fri, 13 July 2018, 08:19:16
wow im very interested in this! was about to order a Archon RE:AL SUPERIOR EX, do you have any experience so you could compare this to yours?
I was very interested in that board as well. Didn't get a chance to buy one tho. That keyboard uses the same sliders so I guess they should be similar.
Post by: wixxzblu on Fri, 13 July 2018, 08:21:13
wow im very interested in this! was about to order a Archon RE:AL SUPERIOR EX, do you have any experience so you could compare this to yours?
I was very interested in that board as well. Didn't get a chance to buy one tho. That keyboard uses the same sliders so I guess they should be similar.
super! i definitely am down for 1 of your custom design, it looks much better than the silver Archon that is available on amazon. :thumb:
Post by: duckboi on Fri, 13 July 2018, 08:24:15
Post by: Ramiel on Fri, 13 July 2018, 08:28:07
Any chance for other layouts for the bottom row?
Sent from my mobile using Tapatalk
Unlike MX switch or even ALPS switch keyboards, an EC keyboard PCB can only support a single layout. I think other layouts, say WKL layout, can only be supported by another newly designed PCB from Niz. That's not impossible according to the good experiences I spoke with Niz.
Post by: Ramiel on Fri, 13 July 2018, 08:31:42
This is really cool! Are you thinking of making more and selling them? (ah wait, this is in the interest check section :p )
Yes, this is a project I've been working for a while. Would like to launch a GB for it if there're enough interests. I also discussed with Niz about the availability of Niz keyboard parts. They agreed to provide the parts I need in low MOQ. I haven't asked for a quote tho.
Post by: Etherealsound on Fri, 13 July 2018, 08:35:13
Post by: Ramiel on Fri, 13 July 2018, 08:39:53
That looks amazing. Can you comment a bit on the feel of the niz switches?
The default 35g domes are way too light for me. The 50g domes feel much better. I lubed all the sliders and housings with dry lube. They are pretty similar to Realforce 55g domes. I like the 50g Niz domes more than BKE Redux light. BKE Redux domes are too sharp for me.
Post by: E.E.L. Ambiense on Fri, 13 July 2018, 09:50:20
NiZ decks are fantastic IMO when you dome-swap. With the sheets that they offer (or even eBay choices) they can really feel great. I use 65g sheet in my Archon right now, and I've used BKE's in there before. I prefer the 65g at the moment.
Edit: My only request would be to have a cherry stab solution instead of Costar style stabs. Granted it would still be plate-mount, but those of us who prefer one over the other would love this.
Post by: FrostyToast on Fri, 13 July 2018, 09:58:39
I would also like a sound demo
Post by: H3NT4I on Fri, 13 July 2018, 10:20:31
...Also is that PBT Muted I see?? :eek: :eek: :eek:
Post by: E.E.L. Ambiense on Fri, 13 July 2018, 10:22:46
Post by: Ramiel on Fri, 13 July 2018, 10:23:14
Edit: My only request would be to have a cherry stab solution instead of Costar style stabs. Granted it would still be plate-mount, but those of us who prefer one over the other would love this.
I like costar stabs better but plate-mount Cherry stabs are feasible
Post by: Ramiel on Fri, 13 July 2018, 10:32:08
Do you know if topre sliders and domes would work with this case and pcb?
I would also like a sound demo
I've never tested but they are mostly compatible according to Niz. Keys larger than 1u are not compatible.
Post by: H3NT4I on Fri, 13 July 2018, 10:35:54
Edit: My only request would be to have a cherry stab solution instead of Costar style stabs. Granted it would still be plate-mount, but those of us who prefer one over the other would love this.
I like costar stabs better but plate-mount Cherry stabs are feasible
Side note, love your stuff man great looking cases and your boards have come out really well! Would love to get a custom from you someday!
Post by: Ramiel on Fri, 13 July 2018, 10:36:52
Awesome looking board, look like these would work with topre/NT too?
...Also is that PBT Muted I see?? :eek: :eek: :eek:
Sliders and housings are possibly compatible. never tried to support Topre parts because there are already several other projects doing that.
Yes, that's a dye sub pbt set.
Post by: E.E.L. Ambiense on Fri, 13 July 2018, 10:42:50
I like costar stabs better but plate-mount Cherry stabs are feasible
Sounds great!
Side note, love your stuff man great looking cases and your boards have come out really well! Would love to get a custom from you someday!
Wow, very kind of you to say! Thanks man. It's appreciated. :)
Post by: mrkantz on Fri, 13 July 2018, 10:49:12
Post by: neon_tom on Fri, 13 July 2018, 11:57:46
Post by: ngb09229 on Fri, 13 July 2018, 12:54:08
Post by: dubious on Fri, 13 July 2018, 13:22:02
Post by: pixelpusher on Fri, 13 July 2018, 13:57:32
Post by: _ODIN_ on Fri, 13 July 2018, 15:33:03
Post by: bisoromi on Fri, 13 July 2018, 19:00:52
How are Niz domes compared to Topre domes?
Post by: Water lee on Sat, 14 July 2018, 00:12:37
Post by: ye_cole on Sat, 14 July 2018, 11:27:53
👀excite
Post by: gutsack on Sat, 14 July 2018, 13:35:55
Post by: duckboi on Sat, 14 July 2018, 17:26:03
Do BKE domes work? From reading the thread think they do, but not 100% sure so wanna ask.
👀excite
I've heard that they work but I do not have a Niz board myself.
Post by: tunadesu on Sat, 14 July 2018, 20:47:19
Post by: Ramiel on Sun, 15 July 2018, 07:13:36
Do BKE domes work? From reading the thread think they do, but not 100% sure so wanna ask.
👀excite
Yes, I tested BKE domes on Niz75 and Niz87. The BKE domes work without any problems. I'm using 50g Niz domes right now because the tactility of BKE domes is too sharp for me.
Post by: Ramiel on Sun, 15 July 2018, 07:18:08
Yes plz. Gonna make me buy a Plum87 again, haha.
You don't need to buy a Plum87 if want to join a future GB of this kit. It's a waste to buy a Plum 87 then throw away the case, plate, and keycaps. I've contacted Plum/Niz. They can provide all the parts I need.
Post by: _ODIN_ on Sun, 15 July 2018, 08:57:36
Case for the plum75?Yes plz. Gonna make me buy a Plum87 again, haha.
You don't need to buy a Plum87 if want to join a future GB of this kit. It's a waste to buy a Plum 87 then throw away the case, plate, and keycaps. I've contacted Plum/Niz. They can provide all the parts I need.
Post by: wixxzblu on Mon, 16 July 2018, 01:57:03
Also, could you provide a typing test video?
Post by: CrashMoon on Thu, 19 July 2018, 01:12:48
Sent from my Pixel using Tapatalk
Post by: Vadurr on Thu, 19 July 2018, 01:40:04
Post by: titanium on Thu, 19 July 2018, 02:00:06
Would be interested in a WKL / Split backspace version :)
not sure if the split backspace would be possible since it's going to use the niz 87 guts
Post by: rlaa1016 on Thu, 19 July 2018, 03:43:45
Post by: lovetree on Thu, 19 July 2018, 21:08:32
Is the stabilizer of your new MK the same as that of Plum NIZ?
If so, could it be possible to change it into cherry stabilizer?
Post by: pvd on Thu, 19 July 2018, 21:42:37
Post by: bisoromi on Thu, 19 July 2018, 23:23:23
Would be interested in a WKL / Split backspace version :)
I’d also be interested in a WKL version
Post by: hikashi1988 on Thu, 19 July 2018, 23:23:58
Would be interested in a WKL / Split backspace version :)(https://blog-imgs-120.fc2.com/w/a/t/watchmonoblog/ATOM66_01.jpg)
I think NiZ atom 66 should be able to do that with programmable function
but I can't try it out since I don't own one :(
.
Post by: rioc on Sat, 21 July 2018, 15:49:56
Sent from my DREA100 using Tapatalk
Post by: ray160 on Sat, 04 August 2018, 16:42:34
Post by: hikashi1988 on Mon, 13 August 2018, 09:58:24
Post by: Ramiel on Mon, 13 August 2018, 18:01:06
any update on this project? :)
(https://i.imgur.com/taqXEnZ.png)
So I ordered a new plate to test the cherry stabs as someone asked.
(https://i.imgur.com/kdLe6Nn.png)
As shown in the photo, it's not possible to support Cherry stabs. The slider housing is too large that leaves no room for the Cherry stabs. Costar stab is the only possible way I can think of.
Post by: Ramiel on Mon, 13 August 2018, 18:07:23
Any suggestions which budget microphone can do the job?
Post by: switchnollie on Tue, 14 August 2018, 14:27:08
Post by: Kallus on Thu, 16 August 2018, 03:37:18
Post by: fcoury on Thu, 16 August 2018, 20:43:27
Post by: hikashi1988 on Mon, 20 August 2018, 23:26:27
Sent from my LG-H930 using Tapatalk
Post by: japancakes on Mon, 27 August 2018, 00:07:10
Post by: Ramiel on Thu, 06 September 2018, 15:21:23
Can you confirm if BKE Redux would work in this?
Yes, BKE Redux works perfectly in the case.
Post by: mrkantz on Thu, 06 September 2018, 15:27:22
Post by: 8Bitterness on Sat, 15 September 2018, 11:59:21
Post by: Ramiel on Sat, 15 September 2018, 17:53:28
I'm curious, how do these feel compared to Topre? I also was Looking as the Archon RE:AL Superior EX but this case is really beautiful in comparison, and that's saying something considering the Archon case was super nice to begin with!
It depends on what domes you use. Most people agree that the Niz 35g domes are too light and not tactile. I'm using 50g domes from Niz and they feel very similar with 45g Realforce domes.
BKE redux domes are also compatible with the case and PCB.
Post by: digisax on Sun, 16 September 2018, 09:49:32
Post by: Gobluebro on Wed, 19 September 2018, 08:19:13
It's fine if it's not, I enjoy these switches a lot so getting another is okay.
Post by: Zuology on Wed, 19 September 2018, 09:18:03
I am interested. I have an ABKO K935P board that uses the same kind of switches. Do you think it would be compatible?
It's fine if it's not, I enjoy these switches a lot so getting another is okay.
I'm curious, how do these feel compared to Topre? I also was Looking as the Archon RE:AL Superior EX but this case is really beautiful in comparison, and that's saying something considering the Archon case was super nice to begin with!
Own(ed) both the Abko and the Archon. Archon is beautiful lubed up and domeswapped (my personal pref is the 65g Hansung OEM domes sold on ebay for a modest price, and they drop right in with no modification aside from some slits to poke some LEDs through on the PCB). Abko is also fantastic, but has a plastic plate IIRC so not like the metal plate found on the Plum TKL.
Post by: mkarlsson on Sat, 22 September 2018, 13:01:08
AFAIK Niz does not do any ISO keyboard right? Do you think it would be possible to do it in this project?
Thanks!
Post by: hikashi1988 on Sun, 23 September 2018, 11:26:19
somehow hoping comparison with realforce / norbaforce.
Post by: tayumpee on Mon, 24 September 2018, 18:20:16
Post by: s3vv4 on Tue, 25 September 2018, 13:31:44
Post by: mkarlsson on Tue, 25 September 2018, 14:24:38
Sorry to get offtopic, but what are those keycaps in OP?
May be KP Republic Muted
https://kprepublic.com/products/muted-colorway-169-cherry-profile-dye-sub-keycap-set-thick-pbt-plastic-keyboard-gh60-xd60-xd84-tada68-rs96-zz96-87-104-660
Post by: NINJER on Wed, 17 October 2018, 07:36:55
Sent from my SM-N960F using Tapatalk
Post by: EightDiagram on Wed, 17 October 2018, 12:11:13
Any chance for other layouts for the bottom row?
Sent from my mobile using Tapatalk
Unlike MX switch or even ALPS switch keyboards, an EC keyboard PCB can only support a single layout. I think other layouts, say WKL layout, can only be supported by another newly designed PCB from Niz. That's not impossible according to the good experiences I spoke with Niz.
If there can only be one layout, I'd prefer standard bottom row. Either way, this looks so nice! :thumb: Looking forward to GB.
Post by: audax989 on Wed, 17 October 2018, 16:22:14
Post by: switchnollie on Thu, 18 October 2018, 19:30:00
Post by: Ramiel on Thu, 18 October 2018, 20:15:11
I am interested. I have an ABKO K935P board that uses the same kind of switches. Do you think it would be compatible?
It's fine if it's not, I enjoy these switches a lot so getting another is okay.
Plum is the OEM so I guess it's compatible. I'm not 100 percent sure.
Post by: Ramiel on Thu, 18 October 2018, 20:18:29
Very interesting project!
AFAIK Niz does not do any ISO keyboard right? Do you think it would be possible to do it in this project?
Thanks!
It's possible only if Plum is willing to develop a new PCB just for a small group of people in the keyboard community.
Just assume that's possible, I would suggest them to make a WKL layout first tbh.
I talked with them before, they said that's possible there are enough interests.
Post by: Ramiel on Thu, 18 October 2018, 20:22:49
It would be great if you can offer the whole board with the niz internals. Is that a possibility
That was the plan b. My original plan was to order only each part from Niz including the PCB, switch housings, springs, domes, sliders, and so on. Niz told me, due to the number I asked, they can only provide me the internals without keycaps, cases, cables. The plate will be wasted because I make top mount aluminum plate.
Post by: Ramiel on Thu, 18 October 2018, 20:27:47
I think some programmability would be sweet.
The PCB is programmable using a Windows software. I only used the 87 RGB version and Bluetooth version keyboards so didn't use the software a lot. The software is not bad according to my limited experiences.
Post by: regionfree on Thu, 18 October 2018, 20:32:07
Post by: Ramiel on Thu, 18 October 2018, 20:40:52
Post by: Ramiel on Thu, 18 October 2018, 20:46:49
but why plum? their version of costar is terrible (I used to own a 75 and an 87), and the consistency of the sliders are bad as well. the stock 35g and 45g domes are too soft, unless you get (the almost always out of stock) 55g or 65g korean domes from ebay. then the sliders. the fit of caps on the sliders are very inconsistent (maybe could be replaced with other custom sliders?).
I have decided to suspend this project but I still disagree with your points.
I use Filco costar stabs and they are not bad at all.
What do you mean by slider consistency? The sliders are smooth after lubing imo.
The so-called Korean domes are actually produced by Plum. The original plan was to provide 55g and 65g domes only. Unfortunately, as I mentioned above, I decide to suspend this project mostly because the lack of 65g domes.
Post by: DasGnome on Thu, 18 October 2018, 21:00:57
but why plum? their version of costar is terrible (I used to own a 75 and an 87), and the consistency of the sliders are bad as well. the stock 35g and 45g domes are too soft, unless you get (the almost always out of stock) 55g or 65g korean domes from ebay. then the sliders. the fit of caps on the sliders are very inconsistent (maybe could be replaced with other custom sliders?).
I have decided to suspend this project but I still disagree with your points.
I use Filco costar stabs and they are not bad at all.
What do you mean by slider consistency? The sliders are smooth after lubing imo.
The so-called Korean domes are actually produced by Plum. The original plan was to provide 55g and 65g domes only. Unfortunately, as I mentioned above, I decide to suspend this project mostly because the lack of 65g domes.
Maybe I'm the odd one out on this, but that's a silly reason to stop for a cool product such as this. Topre domes are very easy to replace, so any user could do so later. People already often use BKE domes instead.
Post by: Zuology on Thu, 18 October 2018, 21:19:22
but why plum? their version of costar is terrible (I used to own a 75 and an 87), and the consistency of the sliders are bad as well. the stock 35g and 45g domes are too soft, unless you get (the almost always out of stock) 55g or 65g korean domes from ebay. then the sliders. the fit of caps on the sliders are very inconsistent (maybe could be replaced with other custom sliders?).
I have decided to suspend this project but I still disagree with your points.
I use Filco costar stabs and they are not bad at all.
What do you mean by slider consistency? The sliders are smooth after lubing imo.
The so-called Korean domes are actually produced by Plum. The original plan was to provide 55g and 65g domes only. Unfortunately, as I mentioned above, I decide to suspend this project mostly because the lack of 65g domes.
Maybe I'm the odd one out on this, but that's a silly reason to stop for a cool product such as this. Topre domes are very easy to replace, so any user could do so later. People already often use BKE domes instead.
I disagree that the stock Niz sliders are scratchy (at least after lubing), and I do not have issues with inconsistent fit on keycaps. I also have no issues with the Niz implementation of costar stabs, which are beautifully quiet and stable with minimal effort to lube them (as opposed to lubing and clipping and band-aid modding cherry-style stabs, which don't fit anyway). I have two Niz-made boards, one which I dome swapped and lubed with BKE Redux Heavies, and the other with the 65g Korean OEM domes and lubed sliders.
I think that you're missing the point about not having to harvest pieces from existing Topre products (rendering the original product non-functional/wasted cost). Also, BKE domes are a b*tch to align properly on Niz PCBs because they do not have the alignment pegs between the switches. Also realize that BKE Redux domes would have be sourced from a third party (Keyclack) who have proven to be unreliable in the past and would complicate logistics even further. I agree that while 55g OEM domes are passable, they are not ideal for the best feel with 65g being my preferred for a rounder tactile bump in contrast to the BKE Redux Heavies which have a pronounced/sharper tactile event.
Regardless, I can understand why Ramiel does not feel like the project can move forward at the moment, and it is his time and project to make the decision on. If people really want a high-end heavy CNC/anodized Niz TKL, the "Archon RE:AL Superior EX" can be sourced from Korea in standard TKL layout, and the case is based on a design by (the) Duck. I think top-mount was a nice ambition to have, but not necessary since the Nopre boards I own and have owned were all sandwich mount assemblies so the flex/bottoming out is not an issue.
Post by: DasGnome on Thu, 18 October 2018, 23:03:54
but why plum? their version of costar is terrible (I used to own a 75 and an 87), and the consistency of the sliders are bad as well. the stock 35g and 45g domes are too soft, unless you get (the almost always out of stock) 55g or 65g korean domes from ebay. then the sliders. the fit of caps on the sliders are very inconsistent (maybe could be replaced with other custom sliders?).
I have decided to suspend this project but I still disagree with your points.
I use Filco costar stabs and they are not bad at all.
What do you mean by slider consistency? The sliders are smooth after lubing imo.
The so-called Korean domes are actually produced by Plum. The original plan was to provide 55g and 65g domes only. Unfortunately, as I mentioned above, I decide to suspend this project mostly because the lack of 65g domes.
Maybe I'm the odd one out on this, but that's a silly reason to stop for a cool product such as this. Topre domes are very easy to replace, so any user could do so later. People already often use BKE domes instead.
I disagree that the stock Niz sliders are scratchy (at least after lubing), and I do not have issues with inconsistent fit on keycaps. I also have no issues with the Niz implementation of costar stabs, which are beautifully quiet and stable with minimal effort to lube them (as opposed to lubing and clipping and band-aid modding cherry-style stabs, which don't fit anyway). I have two Niz-made boards, one which I dome swapped and lubed with BKE Redux Heavies, and the other with the 65g Korean OEM domes and lubed sliders.
I think that you're missing the point about not having to harvest pieces from existing Topre products (rendering the original product non-functional/wasted cost). Also, BKE domes are a b*tch to align properly on Niz PCBs because they do not have the alignment pegs between the switches. Also realize that BKE Redux domes would have be sourced from a third party (Keyclack) who have proven to be unreliable in the past and would complicate logistics even further. I agree that while 55g OEM domes are passable, they are not ideal for the best feel with 65g being my preferred for a rounder tactile bump in contrast to the BKE Redux Heavies which have a pronounced/sharper tactile event.
Regardless, I can understand why Ramiel does not feel like the project can move forward at the moment, and it is his time and project to make the decision on. If people really want a high-end heavy CNC/anodized Niz TKL, the "Archon RE:AL Superior EX" can be sourced from Korea in standard TKL layout, and the case is based on a design by (the) Duck. I think top-mount was a nice ambition to have, but not necessary since the Nopre boards I own and have owned were all sandwich mount assemblies so the flex/bottoming out is not an issue.
It kind of sounds like that first paragraph is talking to me, but I didn't post the complaints about Niz boards so I'm gonna ignore it. lol
I also have a Niz board with BKE and know exactly how annoying it is to align. I don't think I'm missing any points because it's not required to harvest existing Topre products anymore. That's my point. Even if 65g domes aren't available right now, a number of options are either sourced directly from Niz or Keyclack. He doesn't have to take the responsibility for the logistics. MX/Alps GBs often don't provide switches, so I don't really think this is different (although the overall availability is much smaller).
Obviously it's his time and project, so he can do whatever he wants. But, since this is an interest check, I want him to know that I don't think interest stops because his one preferred dome option is not available.
Post by: mkarlsson on Fri, 19 October 2018, 13:23:33
Post by: tonny950111 on Tue, 19 March 2019, 09:38:14
Post by: mrkevint on Tue, 19 March 2019, 10:43:48
I'll be in if you ever decide to run it as a group buy!
Post by: Ramiel on Tue, 19 March 2019, 12:17:26
Wow, definitely looking forward this can come into a GB. Actually I think the design is quite amazing that it will be great to be the first full aluminum custom chassis for the Niz/Plum EC 87 keyboard. You should consider a corporation with Niz. The latest version of Niz housing & sliders will debut in Mid 2019.
Looking forward to the new sliders & hoursings.
There's still no plan for the 65g domes though.
Post by: Gobluebro on Tue, 19 March 2019, 12:18:47
Looking forward to the new sliders & hoursings.
There's still no plan for the 65g domes though.
They restocked them on ebay if you are interested. https://www.ebay.com/itm/142648185860
Post by: tex_live_utility on Tue, 19 March 2019, 16:56:17
Post by: whalematrontron on Tue, 19 March 2019, 17:55:07
Post by: Ramiel on Tue, 19 March 2019, 18:02:52
Ooft is this still happening? It looks amazing
Looking forward to the new sliders & hoursings.
There's still no plan for the 65g domes though.
They restocked them on ebay if you are interested. https://www.ebay.com/itm/142648185860
Oh I didn't know the 65g domes are restocked.
I'll order one sheet and do a typing test.
You can be the judge whether it's worth doing or not after listened the recording.
Post by: Jkshowman on Sat, 27 April 2019, 13:57:32
would love and update on this :)
Post by: Jkshowman on Sat, 27 April 2019, 13:58:45
Show Image(https://i.imgur.com/taqXEnZ.png)
So I ordered a new plate to test the cherry stabs as someone asked.Show Image(https://i.imgur.com/kdLe6Nn.png)
As shown in the photo, it's not possible to support Cherry stabs. The slider housing is too large that leaves no room for the Cherry stabs. Costar stab is the only possible way I can think of.
is it possible to make the plate with more relief cuts? or dare i say even a brass plate?
Post by: equalunique on Sat, 27 April 2019, 14:06:20
Sent from my LG-H918 using Tapatalk
Post by: mikehotel on Wed, 01 May 2019, 10:24:42
Post by: menuhin on Wed, 08 May 2019, 16:55:34
Can you confirm if BKE Redux would work in this?
Yes, BKE Redux works perfectly in the case.
Sold!
Post by: djaeyun on Thu, 09 May 2019, 13:26:15
The Archon RE:AL EX is great but also hard to get outside of Korea.
Post by: Zuology on Thu, 09 May 2019, 15:24:26
The Archon RE:AL EX is great but also hard to get outside of Korea.
Slightly OT, but I had no trouble getting my Archon in the USA, but I must've lucked out on the seller having it in stock right when I was looking to get one. Are they actively making and stocking the Archon's in KR?
Post by: vicissitude on Thu, 09 May 2019, 18:07:44
Post by: zerotank on Mon, 05 August 2019, 15:46:30
Post by: godzillq25 on Sat, 17 April 2021, 09:38:54
Post by: brudder on Tue, 25 January 2022, 01:34:34
It's been dark for a while in the NiZ Discord (https://discord.gg/FMaTksFm) but I think (and hope) this project will resume once the Duo 82 completes fulfillment.