Post by: elton5354 on Sat, 11 April 2015, 10:01:15
**Orders are closed.
(http://i.imgur.com/uJDvSsi.jpg)
(http://i.imgur.com/DoO9Egu.jpg)
ORDER HERE (http://goo.gl/forms/GKGsswNPAJ) <---- Click here to order
Included in this set:
Aluminium top housing (Aluminum 6061) in black, silver, blue-gray, or red (winkey or winkeyless)
Bottom housing (flat acrylic, angled acrylic, or aluminum bottom)
MX Reinforcement Plate (stainless steel, aluminum, or plastic plate)
PCB presoldered (resistors, diodes, smd leds, etc, but not switches)
Fixing bolts
Info:
Limit of 30 sets for first round. If over, will take more time for the later orders.
Case has an angle of 11 degrees for the aluminum bottom, 7 degrees for angled acrylic, and 9 degrees for flat acrylic piece with feet.
Full keymapping
Macro settings
Supports MX switches and ALPs (Optional add-on)
Full LED and RGB SMD LED compatible.
Switches and stabilizers are not included (Requires Cherry PCB stabilizers)
Supports centred caps lock or stepped caps lock.
ALPs reinforcement plate layout only supports old Dell and SGI keycaps and stabilizers.
You must buy a complete set (Top housing, bottom housing, and PCB + Plate) in order to buy the optional add-ons.
More information and pictures on this :
More
http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=2591572
http://kbdlab.co.kr/index.php?document_srl=2631632&mid=board_Lsno50
http://kbdlab.co.kr/index.php?document_srl=2381083&mid=board_Lsno50
http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=3&document_srl=2506641
http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=3&document_srl=2493979
http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=4&document_srl=2418293
http://kbdlab.co.kr/index.php?document_srl=2631632&mid=board_Lsno50
http://kbdlab.co.kr/index.php?document_srl=2381083&mid=board_Lsno50
http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=3&document_srl=2506641
http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=3&document_srl=2493979
http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=4&document_srl=2418293
Price:
(http://i.imgur.com/jdB4Rg1.png)
(http://i.imgur.com/82TWykX.png)
(http://i.imgur.com/0P1caFD.png)
Optional Add-Ons:
ALPs PCB + Plate - $72 USD
MX PCB + Plate - $72 USD
Shipping
Shipping will be from South Korea with EMS. Shipping cost will depend on your location. Each set weighs about (TBD) kg with packaging. Click here to check your zone (https://geekhack.org/index.php?topic=53348.msg1191127#msg1191127) and Click here to check their prices in Korean Won (http://www.koreapost.go.kr/eng/sub/subpage.jsp?contId=e1020300)
Notes
- Deadline for order is April 20, 2015.
- Order ONLY if you can pay the invoice by the deadline (May 1st)
- There will be no extras for sale after this group buy is closed, so please put your order in before it's too late ;)
- I will send invoices through Paypal to everyone, so you need a verified Paypal account to receive and pay. Also please check the information carefully before submitting your order. There will be Paypal fees added to the price.
- If you want to make changes to your order, please send me a PM.
- I can only guarantee damages for 7 days from the day you receive the items.
ORDER HERE (http://goo.gl/forms/GKGsswNPAJ) <---- Click here to order
Check your order here: (I update this manually)
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
Post by: Lastpilot on Sat, 11 April 2015, 11:28:29
Post by: r0mIe_Ng on Sat, 11 April 2015, 11:30:45
Post by: CyriusG on Sat, 11 April 2015, 11:34:40
Post by: rainb1ood on Sat, 11 April 2015, 11:34:59
Hopefully I won't regret not getting the aluminum bottom lol (I went for the acrylic bottom)
Post by: FreeChemicals on Sat, 11 April 2015, 11:38:09
Post by: Flyersfan1 on Sat, 11 April 2015, 11:43:24
Order submitted!I wouldn't regret it, I think there's a lot of people who can't type comfortably with that angle(myself included.)
Hopefully I won't regret not getting the aluminum bottom lol (I went for the acrylic bottom)
Post by: LechnerDE on Sat, 11 April 2015, 11:46:34
Post by: pr1me on Sat, 11 April 2015, 11:47:02
Post by: r0mIe_Ng on Sat, 11 April 2015, 11:50:05
Thanks Elton for doing another fantastic GB !
Post by: tjweir on Sat, 11 April 2015, 12:03:48
Post by: Fnzzy on Sat, 11 April 2015, 12:06:40
Post by: LechnerDE on Sat, 11 April 2015, 12:29:02
(http://www.kbd4u.co.kr/web/upload/editor/2015/04/11/3b176966b2890ea801b910c2ae937471.jpg)
Post by: Lastpilot on Sat, 11 April 2015, 12:33:18
Is the right one the blue-gray top case? Looks totally different than in the other pic with all 4 colors next to each other...Show Image(http://www.kbd4u.co.kr/web/upload/editor/2015/04/11/3b176966b2890ea801b910c2ae937471.jpg)
The right board is actually a raw, not yet anodized model [link (http://kbdlab.co.kr/index.php?document_srl=2381083&mid=board_Lsno50)] [other link (http://duck0113.tistory.com/119)] (it was his demonstration for ALPS compatibility) but the colors in the photo have been manipuated. You can tell from the wood background - clearly the same desk but different color temperatures/saturation. ;)
Post by: LechnerDE on Sat, 11 April 2015, 12:34:57
Can't believe that is supposed to be silver :p
Post by: Latin00032 on Sat, 11 April 2015, 12:36:13
Post by: monotagary on Sat, 11 April 2015, 12:36:21
Post by: pr1me on Sat, 11 April 2015, 12:42:58
Post by: elton5354 on Sat, 11 April 2015, 12:43:12
If you are planning to buy extra bottom and top casing, why not buy another set as you will need another PCB anyway? :D
Post by: wlhlm on Sat, 11 April 2015, 12:44:50
Post by: Khers on Sat, 11 April 2015, 12:48:07
Post by: monotagary on Sat, 11 April 2015, 12:49:33
Could somebody please tell me what the three dots between esc and f1 and the five above the arrows are for? I can't seem to find that info...
Indicator lights.
Post by: gravenshard on Sat, 11 April 2015, 12:50:04
Post by: elton5354 on Sat, 11 April 2015, 12:50:42
Could somebody please tell me what the three dots between esc and f1 and the five above the arrows are for? I can't seem to find that info...
The top holes are for the Caps lock, Num lock, and Scroll lock LEDs. The ones above the arrow keys are up to your customization. No LEDs will be included for them, it's up to you to solder it onto the PCB.
Does some have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
It will probably be around $59 USD to Germany.
Post by: tuantruong on Sat, 11 April 2015, 12:52:30
I wonder if the V2 pcb + plate V2 would fit the V1? And would the alps pcb + plate fit the kingsaver?
And how thick is the flat acrylic bottom?
Thanks!
Post by: Khers on Sat, 11 April 2015, 12:53:25
Could somebody please tell me what the three dots between esc and f1 and the five above the arrows are for? I can't seem to find that info...
Indicator lights.
Could somebody please tell me what the three dots between esc and f1 and the five above the arrows are for? I can't seem to find that info...
The top holes are for the Caps lock, Num lock, and Scroll lock LEDs. The ones above the arrow keys are up to your customization.
Thank you for your replies!
Post by: Prankk on Sat, 11 April 2015, 12:58:24
Post by: kacase on Sat, 11 April 2015, 12:59:59
Post by: elton5354 on Sat, 11 April 2015, 13:02:14
Hi Elton, just submit my order for a set + 2 additional bottoms. :thumb:
I wonder if the V2 pcb + plate V2 would fit the V1? And would the alps pcb + plate fit the kingsaver?
And how thick is the flat acrylic bottom?
Thanks!
Orion V2 PCB and plate will not fit into Orion V1 and vice versa. Won't fit Kingsaver as well.
I'll get back to you on the thickness.
Post by: wlhlm on Sat, 11 April 2015, 13:09:08
Post by: Jason_IRL on Sat, 11 April 2015, 13:13:42
Post by: FreeChemicals on Sat, 11 April 2015, 13:19:17
Post by: KHAANNN on Sat, 11 April 2015, 13:20:22
they are not loading efficiently from the .kr source
Post by: kacase on Sat, 11 April 2015, 13:21:24
Switches (I'm planning on using lubed and stickered ergo clears)
LEDs (for the Indication both next to ESC and above Arrows [what size will fit and will we need diodes/resistors for the LEDs as well?])
Keycaps (my plan TA)
Mini-USB Cable (pexon!)
Soldering Kit
Lots of love!
Post by: elton5354 on Sat, 11 April 2015, 13:24:40
I assumed the top would fit on any of bottom casings, is this correct though?
Yes, of course
So what else do we need to finish the whole keyboard? This is what I had in mind. Please correct me if I missed anything!
Switches (I'm planning on using lubed and stickered ergo clears)
LEDs (for the Indication both next to ESC and above Arrows [what size will fit and will we need diodes/resistors for the LEDs as well?])
Keycaps (my plan TA)
Mini-USB Cable (pexon!)
Soldering Kit
Lots of love!
No need diodes or anything. You just need LEDs. SMD LEDs are provided on the bottom of the PCB.
Out of curiosity, why don't you upload the photos to geekhack?
they are not loading efficiently from the .kr source
Was just lazy. I just uploaded it thru imgur.
Post by: Pemdas on Sat, 11 April 2015, 13:27:25
Been drooling over this keyboard for awhile. I'll probably end up switching color choices too since I'm so damn indecisive :/
Post by: whentheclouds on Sat, 11 April 2015, 13:29:57
So what else do we need to finish the whole keyboard?stabilizers as well, though i have no clue where to source them. perhaps elton can ask Duck if he'd include them alongside the kit (like with the Octagon buy) for an additional fee
Post by: FreeChemicals on Sat, 11 April 2015, 13:31:44
So what else do we need to finish the whole keyboard?stabilizers as well, though i have no clue where to source them. perhaps elton can ask Duck if he'd include them alongside the kit (like with the Octagon buy) for an additional fee
That would be awesome. I've seen them on his webshop: http://www.kbd4u.co.kr/product/detail.html?product_no=19&cate_no=35&display_group=1
If that would be possible, I'd like to get a pair of winkey blockers too: http://www.kbd4u.co.kr/product/detail.html?product_no=20&cate_no=35&display_group=1
Post by: wlhlm on Sat, 11 April 2015, 13:32:06
Would be great if possible. :thumb:So what else do we need to finish the whole keyboard?stabilizers as well, though i have no clue where to source them. perhaps elton can ask Duck if he'd include them alongside the kit (like with the Octagon buy) for an additional fee
Post by: rainb1ood on Sat, 11 April 2015, 13:32:07
No need diodes or anything. You just need LEDs. SMD LEDs are provided on the bottom of the PCB.
What are the sizes of LED that are compatible with the indicators?
Post by: kacase on Sat, 11 April 2015, 13:33:00
I was planning on getting the stabilizers from GON gonskeyboardworks.com (http://gonskeyboardworks.com)
Post by: r0mIe_Ng on Sat, 11 April 2015, 13:34:58
Post by: ph3nomzlol on Sat, 11 April 2015, 13:37:51
Black winkeyless top with that flat acrylic bottom :thumb:
Although, I may change it to the angled acrylic bottom... Hmmmm! Or the top to silver...the possibilities!
What do you guys think of the top colors? Any favs?
Post by: Ahkrael on Sat, 11 April 2015, 13:44:04
The plate and PCB, do they support only one format for the switches on bottom row? 1.25-1-1.25, or do they also support the 1.25-1.25-1.25 with 6.25 spacebar?
Post by: SixtyLife on Sat, 11 April 2015, 13:45:36
Post by: Jason_IRL on Sat, 11 April 2015, 13:46:44
Would be great if possible. :thumb:So what else do we need to finish the whole keyboard?stabilizers as well, though i have no clue where to source them. perhaps elton can ask Duck if he'd include them alongside the kit (like with the Octagon buy) for an additional fee
Agreed. A source for stabilizers would be nice.
Post by: Want on Sat, 11 April 2015, 13:51:10
For those looking for stabilizers, you might want to check Sprit's GB for legit ballin stabs and springs: https://geekhack.org/index.php?topic=55888.0
And congratz all on ordering a pretty baller keyboard.
EDIT: these are only the wires, feel free to ignore this post.
Post by: elton5354 on Sat, 11 April 2015, 13:53:37
First Kustom, will be a fun project. I love the design of the top with LED holes (might even leave the 5 blank not sure).
The plate and PCB, do they support only one format for the switches on bottom row? 1.25-1-1.25, or do they also support the 1.25-1.25-1.25 with 6.25 spacebar?
Supports
1.5 - 1 - 1.5 - 7 - 1.5 - 1 - 1.5
1.25 - 1.25 - 1.25 - 6.25 -1.25 - 1.25 - 1.25 - 1.25
What are the sizes of LED that are compatible with the indicators?
Any LEDs that fit in MX switches should work
Post by: elton5354 on Sat, 11 April 2015, 13:56:18
Post by: FreeChemicals on Sat, 11 April 2015, 13:56:53
I couldn't help myself, got an order placed. I have to admit, I'm a bit shaky atm.
For those looking for stabilizers, you might want to check Sprit's GB for legit ballin stabs and springs: https://geekhack.org/index.php?topic=55888.0
And congratz all on ordering a pretty baller keyboard.
That GB just sells the wires, * Cherry Stabs : All Gold-plated Wires Only : 1set (5pcs) = $12 *
Post by: ph3nomzlol on Sat, 11 April 2015, 13:59:19
Post by: wlhlm on Sat, 11 April 2015, 14:00:10
I couldn't help myself, got an order placed. I have to admit, I'm a bit shaky atm.Yeah, I can feel you! ;)
Post by: Sygaldry on Sat, 11 April 2015, 14:02:05
Post by: kacase on Sat, 11 April 2015, 14:02:33
Post by: Want on Sat, 11 April 2015, 14:04:27
I couldn't help myself, got an order placed. I have to admit, I'm a bit shaky atm.
For those looking for stabilizers, you might want to check Sprit's GB for legit ballin stabs and springs: https://geekhack.org/index.php?topic=55888.0
And congratz all on ordering a pretty baller keyboard.
That GB just sells the wires, * Cherry Stabs : All Gold-plated Wires Only : 1set (5pcs) = $12 *
My bad, totally missed that. Thanks for correcting me, I don't wanna mislead people.
Post by: Novus on Sat, 11 April 2015, 14:04:39
BTW we're already at 30 sets
This is why I begged you not to start it this weekend :))
Post by: GL1TCH3D on Sat, 11 April 2015, 14:04:57
I'm guessing I'm going to be too late for this round =S
Post by: Ouro on Sat, 11 April 2015, 14:05:09
BTW we're already at 30 sets
I just got to my computer and saw that this thread was up. I'm sitting over here debating whether I want the acrylic bottom or not even though I have a RS84 coming in. I GUESS IT DOESNT MATTER ANYMORE
Post by: kacase on Sat, 11 April 2015, 14:06:26
Post by: Sygaldry on Sat, 11 April 2015, 14:06:37
BTW we're already at 30 sets
I just got to my computer and saw that this thread was up. I'm sitting over here debating whether I want the acrylic bottom or not even though I have a RS84 coming in. I GUESS IT DOESNT MATTER ANYMORE
You can still get in. Your order will just take longer.
Post by: elton5354 on Sat, 11 April 2015, 14:09:15
Post by: Fnzzy on Sat, 11 April 2015, 14:11:12
Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45€ shipping and 30-40€ import costs? To be on the save side you can calculate final cost of the keyboard + 90€.
Post by: missalaire on Sat, 11 April 2015, 14:12:32
Elton, tell me my order made it into the 30?! :'(
^ this
Post by: wlhlm on Sat, 11 April 2015, 14:12:43
Got it, thanks! :-*Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45€ shipping and 30-40€ import costs? To be on the save side you can calculate final cost of the keyboard + 90€.
Post by: kacase on Sat, 11 April 2015, 14:14:32
Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45� shipping and 30-40� import costs? To be on the save side you can calculate final cost of the keyboard + 90�.
For Germany it will cost the following
Keyboard cost (depending on what you order)
+19% VAT (you might be lucky and it passes through customs without, but you shouldnt count on it)
+Shipping Costs (around 50$)
Post by: Fnzzy on Sat, 11 April 2015, 14:17:16
Got it, thanks! :-*Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45€ shipping and 30-40€ import costs? To be on the save side you can calculate final cost of the keyboard + 90€.
Since Elton said somewhere that this would be $59 to germany I would add another 10€ to that since my Viper shipping costs were $48 ;D
Order placed! Couldn't wait for this to start! Thanks so much for doing this!
Black winkeyless top with that flat acrylic bottom :thumb:
Although, I may change it to the angled acrylic bottom... Hmmmm! Or the top to silver...the possibilities!
What do you guys think of the top colors? Any favs?
I got the same thing! Black winkeyless top, flat acryllic bottom and a plastic plate. Along with that I'll be using original Cherry WoB or Dolch, and MAYBE white or sky blue LEDs on WASD and F-row. It will be a very stealthy yet classy looking board. :)
I can't wait. :'(
order sheet already up.
Post by: monotagary on Sat, 11 April 2015, 14:18:36
Post by: pr1me on Sat, 11 April 2015, 14:24:59
Sorry you cannot order top casing alone even if you have already ordered a whole set.
If you are planning to buy extra bottom and top casing, why not buy another set as you will need another PCB anyway? :D
I'll probably do that, possible to change my order?
Post by: elton5354 on Sat, 11 April 2015, 14:27:51
I'll probably do that, possible to change my order?
Yeah, just PM me. I would advise not to change it too far in, say a month later.
Also the shipping to Germany estimate was just an estimate. I'll have the weights of each item on Monday.
Post by: wlhlm on Sat, 11 April 2015, 14:31:33
Thanks a lot for doing the calculation!Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45� shipping and 30-40� import costs? To be on the save side you can calculate final cost of the keyboard + 90�.
For Germany it will cost the following
Keyboard cost (depending on what you order)
+19% VAT (you might be lucky and it passes through customs without, but you shouldnt count on it)
+Shipping Costs (around 50$)
Do you really think there's any way this will slip through customs without paying VAT? I mean the box will be huge and heavy and I don't think Elton will declare its value as €20. Did this happen to you before?
Post by: kacase on Sat, 11 April 2015, 14:32:13
Post by: Fnzzy on Sat, 11 April 2015, 14:33:29
Thanks a lot for doing the calculation!Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45� shipping and 30-40� import costs? To be on the save side you can calculate final cost of the keyboard + 90�.
For Germany it will cost the following
Keyboard cost (depending on what you order)
+19% VAT (you might be lucky and it passes through customs without, but you shouldnt count on it)
+Shipping Costs (around 50$)
Do you really think there's any way this will slip through customs without paying VAT? I mean the box will be huge and heavy and I don't think Elton will declare its value as €20. Did this happen to you before?
Everytime I had to pick something up I had to show the invoice and payment confirmation (even for small baggies with keycaps) so I would not count on that :D
Post by: Fnzzy on Sat, 11 April 2015, 14:34:46
what would you guys say is the best plate for ergo clears? My order has a steel plate atm, but I'm not sure whether aluminum or plastic might be even be better.
Using 62g Ergo-Clears on my Viper right now (stainless steel plate). I would say that the switches itself are already pretty soft, so I would go with one of the heavier material plates.
Post by: kacase on Sat, 11 April 2015, 14:35:28
Thanks a lot for doing the calculation!Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45� shipping and 30-40� import costs? To be on the save side you can calculate final cost of the keyboard + 90�.
For Germany it will cost the following
Keyboard cost (depending on what you order)
+19% VAT (you might be lucky and it passes through customs without, but you shouldnt count on it)
+Shipping Costs (around 50$)
Do you really think there's any way this will slip through customs without paying VAT? I mean the box will be huge and heavy and I don't think Elton will declare its value as �20. Did this happen to you before?
It happened to me before twice. Once it was a brand new set of keycaps (DSA Dolch) from SP with the correct Value declared (around 100$) and it went straight through to my mailbox. The other time it was a used TKL, but chances are very very very slim that it will go through without you having to pay VAT.
Post by: Lastpilot on Sat, 11 April 2015, 14:38:18
what would you guys say is the best plate for ergo clears? My order has a steel plate atm, but I'm not sure whether aluminum or plastic might be even be better.Depends on how loud you want your switches.
Steel (loudest) - Alu (less but still loud) - Plastic (not loud)
Duck introduced the plastic plate as the "non-click" plate on the Korean forums.
Post by: wlhlm on Sat, 11 April 2015, 14:38:29
Now that I think about it: When I got my Quickfire Rapid from Korea, it was declared as €20 and came through without paying extra even though the package was quite sizeable. I also got a $170 shipment from Taobao with no custom fees as well, even though I've told my agent to put the actual value on the package.Thanks a lot for doing the calculation!Does someone have experience maybe from previous Korean group buys on what additional costs can I expect when ordering this to Europe or specifically Germany?
I wasn't sure what I paid for my Viper but I think it was around 45� shipping and 30-40� import costs? To be on the save side you can calculate final cost of the keyboard + 90�.
For Germany it will cost the following
Keyboard cost (depending on what you order)
+19% VAT (you might be lucky and it passes through customs without, but you shouldnt count on it)
+Shipping Costs (around 50$)
Do you really think there's any way this will slip through customs without paying VAT? I mean the box will be huge and heavy and I don't think Elton will declare its value as €20. Did this happen to you before?
Everytime I had to pick something up I had to show the invoice and payment confirmation (even for small baggies with keycaps) so I would not count on that :D
Post by: ctrlX on Sat, 11 April 2015, 14:42:43
Post by: kacase on Sat, 11 April 2015, 14:43:58
what would you guys say is the best plate for ergo clears? My order has a steel plate atm, but I'm not sure whether aluminum or plastic might be even be better.Depends on how loud you want your switches.
Steel (loudest) - Alu (less but still loud) - Plastic (not loud)
Duck introduced the plastic plate as the "non-click" plate on the Korean forums.
thanks for clearing that up! So the sound from the switches gets absorbed easiest by plastic, followed by alu and lastly steel; makes total sense from a physical perspective :)
what about the feeling? will it change as well? so softest plastic to hardest steel?
Post by: Bromono on Sat, 11 April 2015, 14:47:08
Post by: frostylove on Sat, 11 April 2015, 14:50:20
Hope it takes less than 2 months to get it in my hands.
Post by: asgeirtj on Sat, 11 April 2015, 14:50:32
what would you guys say is the best plate for ergo clears? My order has a steel plate atm, but I'm not sure whether aluminum or plastic might be even be better.Depends on how loud you want your switches.
Steel (loudest) - Alu (less but still loud) - Plastic (not loud)
Duck introduced the plastic plate as the "non-click" plate on the Korean forums.
The noise is irrelevant if you use o-rings right? What plate is the most sturdy? I saw on some post on GH recently where a plate which could be bent was showcased, is that the plastic plate available here? Also, some people have said that they feel like mx clears feel better with a pcb mounted board, if that is true, wouldn't the true flagship board feature a plate which is bendable (imitates a pcb mounted only board) but as the case has a plate the keyboard has "sturdiness" as people talk about.
Post by: reaxas on Sat, 11 April 2015, 14:52:46
Post by: wlhlm on Sat, 11 April 2015, 14:54:30
Link to the post (https://geekhack.org/index.php?topic=69190.msg1695759#msg1695759)what would you guys say is the best plate for ergo clears? My order has a steel plate atm, but I'm not sure whether aluminum or plastic might be even be better.Depends on how loud you want your switches.
Steel (loudest) - Alu (less but still loud) - Plastic (not loud)
Duck introduced the plastic plate as the "non-click" plate on the Korean forums.
The noise is irrelevant if you use o-rings right? What plate is the most sturdy? I saw on some post on GH recently where a plate which could be bent was showcased, is that the plastic plate available here? Also, some people have said that they feel like mx clears feel better with a pcb mounted board, if that is true, wouldn't the true flagship board feature a plate which is bendable (imitates a pcb mounted only board) but as the case has a plate the keyboard has "sturdiness" as people talk about.
I've decided for a plastic plate for 62g Clears. Am interested how it'll feel.
Post by: Sed8op8 on Sat, 11 April 2015, 14:56:31
I just put my order in and really hoping I can get in with the first 30! I don't see any pictures with the flat acrylic bottom and that what I ordered as I'm not sure i like the extreme angle. Anyways this is going to be my first custom and I'm not sure what choose for a plate and if I will need another PCB incase I screw up the first one. Is there anyone who can list me a short explanation of the differences between plates I'm not getting much info online. Also I hope I can change my plate material if I decide on a different type. This is really great and I am very excited! Thank you so much :thumb:
Post by: elton5354 on Sat, 11 April 2015, 15:02:23
OK, this might be a really silly question. I thought the Orion V2 would come with an ISO option, or was it just a dream? Saw some nice pictures of the ISO plate and/or PCB.
ISO is supported for MX PCB
Hey Elton
I just put my order in and really hoping I can get in with the first 30! I don't see any pictures with the flat acrylic bottom and that what I ordered as I'm not sure i like the extreme angle. Anyways this is going to be my first custom and I'm not sure what choose for a plate and if I will need another PCB incase I screw up the first one. Is there anyone who can list me a short explanation of the differences between plates I'm not getting much info online. Also I hope I can change my plate material if I decide on a different type. This is really great and I am very excited! Thank you so much :thumb:
Some pictures here with flat acrylic bottom with feet
http://kbdlab.co.kr/index.php?document_srl=2381083&mid=board_Lsno50
Post by: Lastpilot on Sat, 11 April 2015, 15:03:03
The noise is irrelevant if you use o-rings right? What plate is the most sturdy? I saw on some post on GH recently where a plate which could be bent was showcased, is that the plastic plate available here? Also, some people have said that they feel like mx clears feel better with a pcb mounted board, if that is true, wouldn't the true flagship board feature a plate which is bendable (imitates a pcb mounted only board) but as the case has a plate the keyboard has "sturdiness" as people talk about.
Well "noise" also means how your keypress impact reverberates through the board - something that happens with or without o-rings. So you will still feel a difference, it will just be dampened with o-rings.
Stainless steel is the most study one. I've seen titanium plates around before too, but that's obviously not a choice here.
Yes - people have differing opinions on PCB vs Plate-mount boards. Since a PCB mounted board has less shared surfaces (1 instead of 2) between switches there is a lower chance of being able to feel the reverberations of adjacent key presses. As a conveat to this the PCB may be subject to bending if not supported properly - so you may feel more of that bending instead. But how all of this feels to the user is subjective and opinions have always been scattered on it.
Post by: Fnzzy on Sat, 11 April 2015, 15:11:52
Post by: CyriusG on Sat, 11 April 2015, 15:12:18
Post by: Rainbow_ on Sat, 11 April 2015, 15:15:12
Post by: Fnzzy on Sat, 11 April 2015, 15:19:54
Are RGB SMD leds installed as standard or do you have to install those yourself?
Those are installed. The only thing you need to solder are switches and in switch LEDs.
Post by: ImDaBaron on Sat, 11 April 2015, 15:20:14
Post by: CyriusG on Sat, 11 April 2015, 15:21:49
Are RGB SMD leds installed as standard or do you have to install those yourself?
Those are installed. The only thing you need to solder are switches and in switch LEDs.
Great, the previous Duck keyboards had standard LEDs so I was a bit unsure if it came with standard or RGB LEDs.
Post by: Lastpilot on Sat, 11 April 2015, 15:25:30
thanks for clearing that up! So the sound from the switches gets absorbed easiest by plastic, followed by alu and lastly steel; makes total sense from a physical perspective :)Yes the feeling changes but it will be more noticeable to those who have heavier keystrokes (bottoming out). So yeah, as you can probably imagine, the harder plates will feel harder and the softer plates will feel softer. Not sure how much my explanation helps LOL.
what about the feeling? will it change as well? so softest plastic to hardest steel?
Post by: Sygaldry on Sat, 11 April 2015, 15:29:08
Perfect explanation!thanks for clearing that up! So the sound from the switches gets absorbed easiest by plastic, followed by alu and lastly steel; makes total sense from a physical perspective :)Yes the feeling changes but it will be more noticeable to those who have heavier keystrokes (bottoming out). So yeah, as you can probably imagine, the harder plates will feel harder and the softer plates will feel softer. Not sure how much my explanation helps LOL.
what about the feeling? will it change as well? so softest plastic to hardest steel?
+100
Post by: orcinus on Sat, 11 April 2015, 15:38:52
Any indication on what the lead times will be for people >30?
Post by: MarkRobbo on Sat, 11 April 2015, 15:41:00
Post by: Rainbow_ on Sat, 11 April 2015, 15:48:54
I second interest in stabilizers and winkey blockers along with the group buy if it would be possible :thumb:
Thirded
Post by: elton5354 on Sat, 11 April 2015, 16:13:12
Depending on the extra orders, if less than 30, then it will be around a month longer.
Not sure on the LED dimming question..anyone with Octagon want to input on this?
Post by: missalaire on Sat, 11 April 2015, 16:17:12
I second interest in stabilizers and winkey blockers along with the group buy if it would be possible :thumb:
^^
Post by: monotagary on Sat, 11 April 2015, 16:25:30
Will we be able to get the aluminum plates colored?
Not from the GB, but you can probably get it colored locally.
Post by: ctrlX on Sat, 11 April 2015, 16:32:38
OK, this might be a really silly question. I thought the Orion V2 would come with an ISO option, or was it just a dream? Saw some nice pictures of the ISO plate and/or PCB.
ISO is supported for MX PCB
Wicked! Order placed. All black alu casing with steel plate (might change this, have to sleep on it).
Post by: pichu23 on Sat, 11 April 2015, 16:38:50
There won't be any blockers, but I'm not sure if they have enough stabilizers. I will get back to you on this.
Depending on the extra orders, if less than 30, then it will be around a month longer.
Not sure on the LED dimming question..anyone with Octagon want to input on this?
Just a quick question, after the first 30 orders are fulfilled. Do we wait for the "second round"? Or do we just put in the order now? :-X
Post by: elton5354 on Sat, 11 April 2015, 16:48:07
There won't be any blockers, but I'm not sure if they have enough stabilizers. I will get back to you on this.
Depending on the extra orders, if less than 30, then it will be around a month longer.
Not sure on the LED dimming question..anyone with Octagon want to input on this?
Just a quick question, after the first 30 orders are fulfilled. Do we wait for the "second round"? Or do we just put in the order now? :-X
It is just that it will be ready to ship after a month or so after the 1st batch is ready to ship. So you can order now and will be invoiced together.
Post by: pichu23 on Sat, 11 April 2015, 17:07:20
There won't be any blockers, but I'm not sure if they have enough stabilizers. I will get back to you on this.
Depending on the extra orders, if less than 30, then it will be around a month longer.
Not sure on the LED dimming question..anyone with Octagon want to input on this?
Just a quick question, after the first 30 orders are fulfilled. Do we wait for the "second round"? Or do we just put in the order now? :-X
It is just that it will be ready to ship after a month or so after the 1st batch is ready to ship. So you can order now and will be invoiced together.
so the rest of the orders after the 30th will be shipped later? that's how i interpret it :p
Post by: yicaoyimu on Sat, 11 April 2015, 18:10:03
Post by: elton5354 on Sat, 11 April 2015, 18:47:18
so the rest of the orders after the 30th will be shipped later? that's how i interpret it :p
To simply put it, yes. :)
I will start invoicing once I know the weight of each item. Probably on Monday.
Post by: ImDaBaron on Sat, 11 April 2015, 19:01:14
Post by: Fnzzy on Sat, 11 April 2015, 19:01:53
Post by: monotagary on Sat, 11 April 2015, 19:04:49
Invoicing next week? Wow this goes by pretty fast. Does that mean we will have our keyboards pretty soon? :D
THE WAITING GAME MIGHT NOT BE THAT LONG AFTER ALL BOYS!
Post by: elton5354 on Sat, 11 April 2015, 19:05:39
Post by: Fnzzy on Sat, 11 April 2015, 19:07:59
They have already been preproducing for about a month now, so maybe in 2 months they will be ready. :thumb:
That's TWO months faster than I expected. :eek: :eek:
Post by: elton5354 on Sat, 11 April 2015, 19:34:39
They have already been preproducing for about a month now, so maybe in 2 months they will be ready. :thumb:
That's TWO months faster than I expected. :eek: :eek:
There are always some delays, so I should've been more conservative and say 2-3 months :)
Post by: pichu23 on Sat, 11 April 2015, 19:40:51
so the rest of the orders after the 30th will be shipped later? that's how i interpret it :p
To simply put it, yes. :)
I will start invoicing once I know the weight of each item. Probably on Monday.
Cheers buddy, ;D
Post by: FrostyToast on Sat, 11 April 2015, 19:41:44
Already filled out the form, but I assume there is only one choice.
Post by: elton5354 on Sat, 11 April 2015, 19:43:18
What material is the ALPS plate going to be in?
Already filled out the form, but I assume there is only one choice.
Only in stainless steel
Post by: PunksDead on Sat, 11 April 2015, 19:49:27
Post by: FrostyToast on Sat, 11 April 2015, 19:52:21
What material is the ALPS plate going to be in?
Already filled out the form, but I assume there is only one choice.
Only in stainless steel
Nice! Situation berry najs.
I ordered just the plastic plate since I don't really care about MX on this board. Although I guess it wouldn't change the price I have to pay.
Also, since you live really close is it possible to get you to proxy my order?
I would like to save money wherever possible.
Post by: elton5354 on Sat, 11 April 2015, 19:54:57
What material is the ALPS plate going to be in?
Already filled out the form, but I assume there is only one choice.
Only in stainless steel
Nice! Situation berry najs.
I ordered just the plastic plate since I don't really care about MX on this board. Although I guess it wouldn't change the price I have to pay.
Also, since you live really close is it possible to get you to proxy my order?
I would like to save money wherever possible.
I have no problem. Are you picking up or do you want me to ship it to London?
It's a 2 hours drive to Toronto..
Post by: FrostyToast on Sat, 11 April 2015, 19:58:08
What material is the ALPS plate going to be in?
Already filled out the form, but I assume there is only one choice.
Only in stainless steel
Nice! Situation berry najs.
I ordered just the plastic plate since I don't really care about MX on this board. Although I guess it wouldn't change the price I have to pay.
Also, since you live really close is it possible to get you to proxy my order?
I would like to save money wherever possible.
I have no problem. Are you picking up or do you want me to ship it to London?
It's a 2 hours drive to Toronto..
I'll probably just get it shipped here if it saves me money.
I don't have much reason to go to Toronto. I wouldn't count on finding a good opportunity for local pickup.
Post by: effectiveduck on Sat, 11 April 2015, 20:03:22
Post by: monotagary on Sat, 11 April 2015, 20:04:29
Is there any way to have it assembled prior to shipping?
Not unless you send it to someone who is willing to assemble it for you. There are no assembly services available for this GB.
Post by: FrostyToast on Sat, 11 April 2015, 20:06:41
Is there any way to have it assembled prior to shipping?
You could probably have it shipped to GON. Shipping wouldn't be that bad since it would be domestically sent within Korea.
Post by: elton5354 on Sat, 11 April 2015, 20:12:32
I'll probably just get it shipped here if it saves me money.
I don't have much reason to go to Toronto. I wouldn't count on finding a good opportunity for local pickup.
I'm only guesstimating but I checked the shipping cost would be about $14 regular parcel.
Is there any way to have it assembled prior to shipping?
Sorry, no assembly, but like others have said you could try sending it to GON. Give him a message first.
Post by: FrostyToast on Sat, 11 April 2015, 20:14:55
I'll probably just get it shipped here if it saves me money.
I don't have much reason to go to Toronto. I wouldn't count on finding a good opportunity for local pickup.
I'm only guesstimating but I checked the shipping cost would be about $14 regular parcel.
Nice. Just toss me an invoice for whatever you think the added cost will be for your package and whatever it will cost to have it sent here. :thumb:
Post by: pichu23 on Sat, 11 April 2015, 20:29:16
What material is the ALPS plate going to be in?
Already filled out the form, but I assume there is only one choice.
Only in stainless steel
Nice! Situation berry najs.
I ordered just the plastic plate since I don't really care about MX on this board. Although I guess it wouldn't change the price I have to pay.
Also, since you live really close is it possible to get you to proxy my order?
I would like to save money wherever possible.
I have no problem. Are you picking up or do you want me to ship it to London?
It's a 2 hours drive to Toronto..
TIL: There's a London in Canada. :-X Sorry for the side track. Hah
Post by: lionblinds on Sat, 11 April 2015, 20:33:10
Post by: Dreamre on Sat, 11 April 2015, 20:49:23
Post by: KatzenKinder on Sat, 11 April 2015, 20:52:04
Post by: elton5354 on Sat, 11 April 2015, 20:57:06
Elton, if I come pick up the KB at your house...would I still have to pay for shipping? :D...
If FrostyToast is going to be joining my order as well, the shipping cost will increase about 33%. We will have to split the shipping in thirds ;). The only thing is free (or not with gas or if you're taking the bus) is picking up :thumb:
Is there any idea about how much more time would be needed for the extra orders? I'm considering going in on this, just want to be kind of informed about when the +30 orders might ship out.
It will be about a month extra. Maybe I need to stop taking orders at 60 sets....
Order submitted!
What happened to the group buy in China? :P
Post by: cmadrid on Sat, 11 April 2015, 20:58:34
Post by: effectiveduck on Sat, 11 April 2015, 21:13:09
Do we need to add any of the case LED's (under the pcb and the dots beside esc and above the arrow keys)? Or are they pre soldered? And if so do we get to choose the colours or are they rgb? The reason i ask is I think the I'd only need switches and stabs from GON, correct?Is there any way to have it assembled prior to shipping?
Sorry, no assembly, but like others have said you could try sending it to GON. Give him a message first.
Post by: orcinus on Sat, 11 April 2015, 21:23:49
Do we need to add any of the case LED's (under the pcb and the dots beside esc and above the arrow keys)? Or are they pre soldered?
Presoldered SMDs.
You only need the top LEDs, AFAIK.
Post by: elton5354 on Sat, 11 April 2015, 21:26:24
Do we need to add any of the case LED's (under the pcb and the dots beside esc and above the arrow keys)? Or are they pre soldered? And if so do we get to choose the colours or are they rgb? The reason i ask is I think the I'd only need switches and stabs from GON, correct?
Indicator LEDs (top left and above arrow keys) and switch LEDs are needed if you want them. The SMD RGB LEDs are presolder onthe underside of the PCB
Post by: effectiveduck on Sat, 11 April 2015, 21:37:40
Do we need to add any of the case LED's (under the pcb and the dots beside esc and above the arrow keys)? Or are they pre soldered? And if so do we get to choose the colours or are they rgb? The reason i ask is I think the I'd only need switches and stabs from GON, correct?
Indicator LEDs (top left and above arrow keys) and switch LEDs are needed if you want them. The SMD RGB LEDs are presolder onthe underside of the PCB
Awesome, thanks.
Post by: duzeyao on Sat, 11 April 2015, 22:08:39
Post by: KatzenKinder on Sat, 11 April 2015, 22:18:02
Post by: elton5354 on Sat, 11 April 2015, 22:23:08
EDIT: Actually it's 59. I'll take one more. :cool:
Post by: Flyersfan1 on Sat, 11 April 2015, 22:24:47
Post by: 3Love on Sat, 11 April 2015, 22:41:09
I'm going to stop the orders now. It's at 60 sets..it's way more than expected. I'll take more orders if they allow or if there are unpaid orders..I just order it, add me on the list please :confused:
EDIT: Actually it's 59. I'll take one more. :cool:
Post by: elton5354 on Sat, 11 April 2015, 22:42:50
I'm going to stop the orders now. It's at 60 sets..it's way more than expected. I'll take more orders if they allow or if there are unpaid orders..I just order it, add me on the list please :confused:
EDIT: Actually it's 59. I'll take one more. :cool:
Oh you just made it. Orders are closed for now.
You can still add in your order, but I won't add you to my official list and the public sheet. I'll put you in if there are unpaid orders.
Post by: FrostyToast on Sat, 11 April 2015, 22:50:39
A GB that closed within the day?
Post by: missalaire on Sat, 11 April 2015, 22:55:15
This is insane.
A GB that closed within the day?
A testament to the fact that mechanical keyboards are a rapidly growing hobby :)
Doesn't hurt that there's cheaper options too.
Post by: monotagary on Sat, 11 April 2015, 23:00:48
This is insane.
A GB that closed within the day?
A testament to the fact that mechanical keyboards are a rapidly growing hobby :)
Doesn't hurt that there's cheaper options too.
Yeah, I think the cheaper options attracted a lot of would be buyers.
Post by: HelixDan on Sat, 11 April 2015, 23:01:28
Post by: sakai4eva on Sat, 11 April 2015, 23:02:35
Post by: yuktsi on Sat, 11 April 2015, 23:42:02
I can't believe I just made it :thumb:
Post by: jaemzp on Sat, 11 April 2015, 23:50:18
I go out for an hour, come back and this happens T.T
Please, someone don't pay on time lol.
Post by: wangbwhz on Sat, 11 April 2015, 23:56:53
Post by: KnivesM on Sun, 12 April 2015, 00:14:54
Post by: elton5354 on Sun, 12 April 2015, 00:15:37
>:D i come late, but is still order.. when will be second round coming out
Wait until payment deadline ;)
Are you only doing 60? or a few more?
Doing what is already on the sheet which is 61.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
oh it wasn't mentioned and if anyone who ordered the aluminum bottoms was wondering, the acrylic flat sides are included with the set.
Post by: radio_killah on Sun, 12 April 2015, 00:15:55
Are you only doing 60? or a few more?
Originally he was only planning on doing 30... :eek:
Post by: KnivesM on Sun, 12 April 2015, 00:20:40
Yea I saw that, but he said he would do another round of 30, just not sure if he has said he was willing to do more or not, haven't read through the last 4 pages yet.Are you only doing 60? or a few more?
Originally he was only planning on doing 30... :eek:
Post by: archer on Sun, 12 April 2015, 00:33:00
Post by: Ahkrael on Sun, 12 April 2015, 00:39:43
Post by: asdfasdfasdf on Sun, 12 April 2015, 00:40:42
What are the optional add-on for:
ALPs PCB + Plate - $72 USD
MX PCB + Plate - $72 USD
Or rather why is this being called an optional add on?
Don't you need these to complete the board?
Post by: monotagary on Sun, 12 April 2015, 00:49:07
I don't quite get this.
What are the optional add-on for:
ALPs PCB + Plate - $72 USD
MX PCB + Plate - $72 USD
Or rather why is this being called an optional add on?
Don't you need these to complete the board?
The ALPs PCB and plate is an optional add-on. MX PCB + Plate is required to join the buy.
Post by: monotagary on Sun, 12 April 2015, 00:50:47
Quick question on plates - the plastic, is it thin enough to remove the switch tops while in the plate? Or are all plates same thickness, and require unsoldering to open switch top?
All plates should be 1.5mm thick. I'm pretty sure. So no switchtop removal.
Post by: laguar on Sun, 12 April 2015, 03:09:40
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
Something is wonky with this sheet. I am in the US, not Vietnam. And very sad to be 31 :(
Post by: StylinGreymon on Sun, 12 April 2015, 03:21:37
Almost.
Post by: sakai4eva on Sun, 12 April 2015, 03:27:03
Also, can I still get the plate + PCB option?
Post by: wlhlm on Sun, 12 April 2015, 03:33:27
I'll be using Clears with the plastic plate.
Post by: kacase on Sun, 12 April 2015, 03:56:26
Post by: Want on Sun, 12 April 2015, 04:44:04
What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
Gaterons blacks, trying out springs when the switches and springs arrive. Going on a plastic plate cuz pings and whatnot.
My only concern with the plastic plate is wether there will be light leaking through from the back of the board in random places.
Post by: kingslenkds on Sun, 12 April 2015, 05:54:31
Post by: tjweir on Sun, 12 April 2015, 06:29:00
How to order? I would like to join a. :thumb:
Orders are closed for now.
I'd recommend subscribing to this topic and watch for a post about the next round.
Post by: Fnzzy on Sun, 12 April 2015, 07:34:16
Post by: ninjadoc on Sun, 12 April 2015, 08:46:46
Post by: kacase on Sun, 12 April 2015, 09:10:53
Wow. I've never seen a group buy close in less than 15 hours. Impressive.
this keyboard looks so great and ducks keyboards are extremely high quality... a lot of us have been waiting for this for very long!
so happy to finaly see it happen :thumb:
can't wait to get it going!!!
Post by: elton5354 on Sun, 12 April 2015, 09:17:05
@elton, can you put me on the waiting list for this one?
Also, can I still get the plate + PCB option?
Fill in the form and you will be in the waiting list. Though there will be 10 others in front of you. :blank:
How to order? I would like to join a. :thumb:
Click on "ORDER HERE"
Post by: Sed8op8 on Sun, 12 April 2015, 09:26:03
I'm in the same boat I just got some Gatorade blacks,some krytox and have some sprit gold springs coming in 62,65 and 68g variants so I can try different resistances to see which ones i like the most. I have heard the gat blacks are about as smooth as vintage blacks stock so lubed I hope they will be like butter. I'm having fun getting everything I need together soldering station, goose neck magnifying lamp,switches,springs and stabs (which I still need to source). I also need to find a couple (cheap) old boards to swap switches and practice my soldering. It would be easier to buy pre lubed,spring swapped and STICKERED switches but they are expensive and I wouldn't learn that way. Just looking at the PCB with all the leads is a little daunting but I'm pretty determined :) anyways thanks again Elton I'm very excited to start my first custom board !What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
Gaterons blacks, trying out springs when the switches and springs arrive. Going on a plastic plate cuz pings and whatnot.
My only concern with the plastic plate is wether there will be light leaking through from the back of the board in random places.
Post by: wlhlm on Sun, 12 April 2015, 09:33:02
Post by: Sed8op8 on Sun, 12 April 2015, 09:43:17
Hmmm, snickered switches sounds delicious! :pLol...I thought so myself :))
Post by: Want on Sun, 12 April 2015, 09:53:10
I'm in the same boat I just got some Gatorade blacks,some krytox and have some sprit gold springs coming in 62,65 and 68g variants so I can try different resistances to see which ones i like the most. I have heard the gat blacks are about as smooth as vintage blacks stock so lubed I hope they will be like butter. I'm having fun getting everything I need together soldering station, goose neck magnifying lamp,switches,springs and stabs (which I still need to source). I also need to find a couple (cheap) old boards to swap switches and practice my soldering. It would be easier to buy pre lubed,spring swapped and snickered switches but they are expensive and I wouldn't learn that way. Just looking at the PCB with all the leads is a little daunting but I'm pretty determined :) anyways thanks again Elton I'm very excited to start my first custom board !What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
Gaterons blacks, trying out springs when the switches and springs arrive. Going on a plastic plate cuz pings and whatnot.
My only concern with the plastic plate is wether there will be light leaking through from the back of the board in random places.
Cool, I also ordered Krytox lube and gold 62g, 65g, 68g and 72g springs, also trying out weights. Will probably be able to sell the unused springs relatively easily later. I think the hunt for parts and putting it all together is part of the fun, so although my experience with soldering is sub-par, I look forward to it :D
Hmmm, snickered switches sounds delicious! :p
Tactile nuts?
Post by: wlhlm on Sun, 12 April 2015, 10:01:48
:))Hmmm, snickered switches sounds delicious! :p
Tactile nuts?
No, smooth as caramel!
Post by: MarkRobbo on Sun, 12 April 2015, 10:02:45
I'm in the same boat I just got some Gatorade blacks,some krytox and have some sprit gold springs coming in 62,65 and 68g variants so I can try different resistances to see which ones i like the most. I have heard the gat blacks are about as smooth as vintage blacks stock so lubed I hope they will be like butter. I'm having fun getting everything I need together soldering station, goose neck magnifying lamp,switches,springs and stabs (which I still need to source). I also need to find a couple (cheap) old boards to swap switches and practice my soldering. It would be easier to buy pre lubed,spring swapped and snickered switches but they are expensive and I wouldn't learn that way. Just looking at the PCB with all the leads is a little daunting but I'm pretty determined :) anyways thanks again Elton I'm very excited to start my first custom board !What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
Gaterons blacks, trying out springs when the switches and springs arrive. Going on a plastic plate cuz pings and whatnot.
My only concern with the plastic plate is wether there will be light leaking through from the back of the board in random places.
Cool, I also ordered Krytox lube and gold 62g, 65g, 68g and 72g springs, also trying out weights. Will probably be able to sell the unused springs relatively easily later. I think the hunt for parts and putting it all together is part of the fun, so although my experience with soldering is sub-par, I look forward to it :D
Ill take the 62g if you don't decide on those ;)
Post by: ctrlX on Sun, 12 April 2015, 10:32:02
What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
I will most likely go with MX clears. Ordered steel plate but considered both plastic and alu.
This will also be my first custom board. As a matter of fact the GB was so quick I haven't even ordered switches and stabilizers. Any good tips on where to buy MX clear switches and stabilizers?
Will any of guys install switch LEDs? I will, but have no clue where to get em as am very new to the mechanical keyboard scene. So any tips and/or suggestions on where to get switches, stabilizers and in-switch LEDs would be greatly appreciated.
Post by: wlhlm on Sun, 12 April 2015, 10:44:31
Why did you ultimately decide for steel?What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
I will most likely go with MX clears. Ordered steel plate but considered both plastic and alu.
This will also be my first custom board. As a matter of fact the GB was so quick I haven't even ordered switches and stabilizers. Any good tips on where to buy MX clear switches and stabilizers?I'd get my switches from 7bit (http://deskthority.net/group-buys-f50/cherry-mx-taking-pre-orders-t2760.html). LEDs from ebay (http://stores.ebay.com/IC-Touch-Store/2x3x4-Rectangle-LEDs-/_i.html?_fsub=4091520013&_sid=1028435323&_trksid=p4634.c0.m322).
Will any of guys install switch LEDs? I will, but have no clue where to get em as am very new to the mechanical keyboard scene. So any tips and/or suggestions on where to get switches, stabilizers and in-switch LEDs would be greatly appreciated.
Post by: ctrlX on Sun, 12 April 2015, 11:11:35
Why did you ultimately decide for steel?What type of switches (tactile, linear, etc.) will you be putting in the board? I'm trying to get an idea of switch/plate combinations you went for.
I'll be using Clears with the plastic plate.
I will most likely go with MX clears. Ordered steel plate but considered both plastic and alu.This will also be my first custom board. As a matter of fact the GB was so quick I haven't even ordered switches and stabilizers. Any good tips on where to buy MX clear switches and stabilizers?I'd get my switches from 7bit (http://deskthority.net/group-buys-f50/cherry-mx-taking-pre-orders-t2760.html). LEDs from ebay (http://stores.ebay.com/IC-Touch-Store/2x3x4-Rectangle-LEDs-/_i.html?_fsub=4091520013&_sid=1028435323&_trksid=p4634.c0.m322).
Will any of guys install switch LEDs? I will, but have no clue where to get em as am very new to the mechanical keyboard scene. So any tips and/or suggestions on where to get switches, stabilizers and in-switch LEDs would be greatly appreciated.
I like my keyboards heavy and sturdy. Hence my decision for going with steel. If it becomes too loud I'd probably install o-rings. However if there was an option for buying an extra plastic plate I might go for it as well. Just to try out the feel of it.
Thanks for the tips! :-D
Post by: 3Love on Sun, 12 April 2015, 13:54:38
Post by: elton5354 on Sun, 12 April 2015, 15:09:55
Is there somebody has repeat orders?
Just multiple orders per person. No worry, you are still in
Post by: 3Love on Sun, 12 April 2015, 15:37:50
I see. Otherwise, when we need to pay it?Is there somebody has repeat orders?
Just multiple orders per person. No worry, you are still in
Post by: wlhlm on Sun, 12 April 2015, 15:48:28
winkey vs. winkeyless: | 34:28 |
blue grey vs. silver vs. black vs. red top: | 22:21:17:2 |
steel vs. aluminium vs. plastic plate (addons): | 23(0):22(2):17(3) |
aluminium vs. angled acrylic vs. flat acrylic bottom (addons): | 32(4):20(14):10(5) |
avg. money spent (overall): | $358 ($21953) |
People opted for an aluminium bottom but want to try out the angled acrylic variant. Nobody loves red. Most went for a steel plate.
Post by: MarkRobbo on Sun, 12 April 2015, 15:53:15
Post by: CyriusG on Sun, 12 April 2015, 16:05:07
Post by: r0mIe_Ng on Sun, 12 April 2015, 16:12:50
Post by: LONGZILLA on Sun, 12 April 2015, 16:25:00
Post by: Sed8op8 on Sun, 12 April 2015, 18:13:38
Surprised there aren't more flat acrylic bottoms as addons considering they are so darn cheap :pI went for the flat acrylic bottom but for some reason thought it was a frosted bottom not clear. I might change my order for the angled acrylic as that appears to be frosted (I'm really on the fence as to wether I really like the clear bottom with exposed PCB or I hate it). Also I went with the plastic plate because I think in lastpilots GON Crystal TKL build video he uses a plastic plate (someone correct me if I'm wrong) and the sound of the board in his subsequent typing video was amazing!!! I really loved it and seeing and reading the process he documented really inspired me to want to build my own. Seriously that board sounds amazing being typed on and I love the very muffled pitter patter of the keys on that thing they sounded sublime!
Post by: FreeChemicals on Sun, 12 April 2015, 18:20:06
(http://i.imgur.com/hg37Mmr.png)
By the way, will the MX plate be white too?
Post by: r0mIe_Ng on Sun, 12 April 2015, 18:44:24
I was browsing through some of the links in the OP and noticed this specific full alu bottom doesn't have 3M feet, as opposed to the 22$ plate. Will those pads be included, or should I find some on my own?Show Image(http://i.imgur.com/hg37Mmr.png)
By the way, will the MX plate be white too?
Edited: misunderstanding abt ur question lol
Post by: elton5354 on Sun, 12 April 2015, 19:45:16
Surprised there aren't more flat acrylic bottoms as addons considering they are so darn cheap :pI went for the flat acrylic bottom but for some reason thought it was a frosted bottom not clear. I might change my order for the angled acrylic as that appears to be frosted (I'm really on the fence as to wether I really like the clear bottom with exposed PCB or I hate it). Also I went with the plastic plate because I think in lastpilots GON Crystal TKL build video he uses a plastic plate (someone correct me if I'm wrong) and the sound of the board in his subsequent typing video was amazing!!! I really loved it and seeing and reading the process he documented really inspired me to want to build my own. Seriously that board sounds amazing being typed on and I love the very muffled pitter patter of the keys on that thing they sounded sublime!
I would choose the frosted angled acrylic. Why? Cause it looks MUCH cooler especially with that uniform glow underneath the PCB. You won't get a 2nd chance in changing once you receive it and will live to regret your decision if you hate it. :P
bottom plates work on V1?
Let me confirm but most likely it is able to
I was browsing through some of the links in the OP and noticed this specific full alu bottom doesn't have 3M feet, as opposed to the 22$ plate. Will those pads be included, or should I find some on my own?Show Image(http://i.imgur.com/hg37Mmr.png)
By the way, will the MX plate be white too?
They will all come with 3M feet. The metal plates will be silver and plastic will be frosted like in the pictures.
Post by: ramnes on Sun, 12 April 2015, 20:02:07
Post by: ph3nomzlol on Sun, 12 April 2015, 20:26:22
Any reason you guys went with WK or WKL? Looks? The 2 extra (or less) keys?
Post by: Prankk on Sun, 12 April 2015, 21:06:52
I'm sort of torn between winkey or winkeyless lol. My gut said winkeyless as it just looks so good with those built-in blockers in the aluminum top... :cool:
Any reason you guys went with WK or WKL? Looks? The 2 extra (or less) keys?
It's all about those looks though. And i don't have a winkeyless board yet. The question I keep struggling with is what plate material I should go with? Elton has already changed it once for me. Any advice from seasoned vets?
Post by: slickmamba on Sun, 12 April 2015, 21:17:19
Post by: elton5354 on Sun, 12 April 2015, 21:21:37
I'm sort of torn between winkey or winkeyless lol. My gut said winkeyless as it just looks so good with those built-in blockers in the aluminum top... :cool:
Any reason you guys went with WK or WKL? Looks? The 2 extra (or less) keys?
It's all about those looks though. And i don't have a winkeyless board yet. The question I keep struggling with is what plate material I should go with? Elton has already changed it once for me. Any advice from seasoned vets?
Lastpilot has gave us a pretty good explanation on the different types of plates and how it feels some pages back. It depends on what switches you use too I suppose
Post by: Prankk on Sun, 12 April 2015, 21:29:46
I'm sort of torn between winkey or winkeyless lol. My gut said winkeyless as it just looks so good with those built-in blockers in the aluminum top... :cool:
Any reason you guys went with WK or WKL? Looks? The 2 extra (or less) keys?
It's all about those looks though. And i don't have a winkeyless board yet. The question I keep struggling with is what plate material I should go with? Elton has already changed it once for me. Any advice from seasoned vets?
Lastpilot has gave us a pretty good explanation on the different types of plates and how it feels some pages back. It depends on what switches you use too I suppose
not sure how i missed all that. thanks.
Post by: wlhlm on Mon, 13 April 2015, 01:06:39
I'm sort of torn between winkey or winkeyless lol. My gut said winkeyless as it just looks so good with those built-in blockers in the aluminum top... :cool:I'm not 100% sure about this either.
Any reason you guys went with WK or WKL? Looks? The 2 extra (or less) keys?
My thoughts were this: What modifiers do I want/need?
I definitely need Ctrl for shortcuts, as well as Windows/Super (for window management, etc.). I also want to have Escape near the modifier area since I'm a vim user and that definitely makes things easier. CapsLock I can totally ditch. So, that leaves me with the following option: put Escape on CapsLock, Ctrl on Ctrl and Windows/Super on Alt. In this case, I'm missing an Alt key and even though I use it seldomly at the moment, maybe I take a go emacs at some point and having an Alt key with that helps. That's why I'm currently on winkey.
If you are not dependent on Escape, you can put Ctrl on CapsLock, Windows on Ctrl and Alt on Alt.
I'm interested in what configurations other Linux-desktop users went for.
Post by: FreeChemicals on Mon, 13 April 2015, 02:41:52
Surprised there aren't more flat acrylic bottoms as addons considering they are so darn cheap :pI went for the flat acrylic bottom but for some reason thought it was a frosted bottom not clear. I might change my order for the angled acrylic as that appears to be frosted (I'm really on the fence as to wether I really like the clear bottom with exposed PCB or I hate it). Also I went with the plastic plate because I think in lastpilots GON Crystal TKL build video he uses a plastic plate (someone correct me if I'm wrong) and the sound of the board in his subsequent typing video was amazing!!! I really loved it and seeing and reading the process he documented really inspired me to want to build my own. Seriously that board sounds amazing being typed on and I love the very muffled pitter patter of the keys on that thing they sounded sublime!
I would choose the frosted angled acrylic. Why? Cause it looks MUCH cooler especially with that uniform glow underneath the PCB. You won't get a 2nd chance in changing once you receive it and will live to regret your decision if you hate it. :Pbottom plates work on V1?
Let me confirm but most likely it is able toI was browsing through some of the links in the OP and noticed this specific full alu bottom doesn't have 3M feet, as opposed to the 22$ plate. Will those pads be included, or should I find some on my own?Show Image(http://i.imgur.com/hg37Mmr.png)
By the way, will the MX plate be white too?
They will all come with 3M feet. The metal plates will be silver and plastic will be frosted like in the pictures.
Great, that is good to know. I should've asked for the MX PCB instead of the plate, but this is valuable information as well.
By the way, regarding the winkeyless discussion: I'd kill myself if my keyboard would miss it. It's my window manager mod key @ linux, so I use it all the time! When I use Windows, I use it to launch applications (win+r/1-9), resize windows (win+arrows), jump to desktop (win+d), etc.
Post by: kacase on Mon, 13 April 2015, 02:56:20
I'm sort of torn between winkey or winkeyless lol. My gut said winkeyless as it just looks so good with those built-in blockers in the aluminum top... :cool:I'm not 100% sure about this either.
Any reason you guys went with WK or WKL? Looks? The 2 extra (or less) keys?
My thoughts were this: What modifiers do I want/need?
I definitely need Ctrl for shortcuts, as well as Windows/Super (for window management, etc.). I also want to have Escape near the modifier area since I'm a vim user and that definitely makes things easier. CapsLock I can totally ditch. So, that leaves me with the following option: put Escape on CapsLock, Ctrl on Ctrl and Windows/Super on Alt. In this case, I'm missing an Alt key and even though I use it seldomly at the moment, maybe I take a go emacs at some point and having an Alt key with that helps. That's why I'm currently on winkey.
If you are not dependent on Escape, you can put Ctrl on CapsLock, Windows on Ctrl and Alt on Alt.
I'm interested in what configurations other Linux-desktop users went for.
I was scared for a second when you were talking about remapping the esc key, and I was wondering why the hell there wouldnt be one on a WINKEYless keyboard. I love my esc right where it is. I use sublime text a lot and it is not dependent on the winkey at all, so I am very happy with my winkeyless choice. Maybe I will map some of the macros on other keys e.g. win + L to lock my pc but ill see about that when my holy grail arrives!
Post by: kingslenkds on Mon, 13 April 2015, 09:58:18
Post by: JaccoW on Mon, 13 April 2015, 10:08:31
Even though I'm not in this GB I would be interested in picking up another plate + PCB to be able to easily swap around my V1 board.bottom plates work on V1?Let me confirm but most likely it is able to
Post by: Blackehart on Mon, 13 April 2015, 12:36:28
Seriously?!
closed already?!
The one weekend i go out of town and I miss the one tkl i want...
ffs..
:'( :'( :'( :'( :'( :'( :'( :'(
Post by: FrostyToast on Mon, 13 April 2015, 13:01:24
The geekkey is worth it in my opinion. I'm not a fan of winkey but the case alone makes it worth it. Had I not put a order in for another GB I would consider it my self.
WTF?!GG
Seriously?!
closed already?!
The one weekend i go out of town and I miss the one tkl i want...
ffs..
:'( :'( :'( :'( :'( :'( :'( :'(
Time to get the Mira. ;D
Post by: Blackehart on Mon, 13 April 2015, 13:20:58
Was more gung-ho about the Orion.
I'll take small led holes over big over the top branding.
Post by: cooldiscretion on Mon, 13 April 2015, 14:09:11
It's a little pricey, but if you like the damped cream SKCM ALPS, then it's keycaps + switches in one go.
http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35 (http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35)
Post by: wlhlm on Mon, 13 April 2015, 14:14:25
http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35 (http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35)Are you sure I should trust seller "randomcomputerbiz"? :))
Post by: cooldiscretion on Mon, 13 April 2015, 14:16:54
http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35 (http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35)Are you sure I should trust seller "randomcomputerbiz"? :))
Who knows. Feedback numbers aren't too good, but he is selling something that's hard to find. It's up to you.
Post by: wlhlm on Mon, 13 April 2015, 14:19:16
Was just mocking about the name.http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35 (http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35)Are you sure I should trust seller "randomcomputerbiz"? :))
Who knows. Feedback numbers aren't too good, but he is selling something that's hard to find. It's up to you.
Post by: cooldiscretion on Mon, 13 April 2015, 14:21:51
Was just mocking about the name.http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35 (http://www.ebay.com/itm/Vintage-Silicon-Graphics-SGI-Clicky-Keyboard-9500900-Alps-Granite-/251918220597?hash=item3aa77efd35)Are you sure I should trust seller "randomcomputerbiz"? :))
Who knows. Feedback numbers aren't too good, but he is selling something that's hard to find. It's up to you.
It is silly, isn't it.
Post by: limitz on Mon, 13 April 2015, 17:15:07
Post by: dakuzo on Mon, 13 April 2015, 18:09:28
Shame. Didn't check GB's all weekend, and find out it's already sold out. Real shame here.
Still put in an order, hoping people somehow change their minds
Post by: elton5354 on Mon, 13 April 2015, 21:32:38
Post by: Rainbow_ on Mon, 13 April 2015, 21:45:26
Adding the weights right now. After that I will start invoicing.
Nice. Can't wait to give you my money! Also receive my keyboard.
Post by: elton5354 on Mon, 13 April 2015, 23:44:43
Post by: duzeyao on Mon, 13 April 2015, 23:50:53
Post by: Jason_IRL on Tue, 14 April 2015, 00:34:05
Post by: Rainbow_ on Tue, 14 April 2015, 00:39:35
Paid!
Same, unfortunately PayPal had me do an eCheck and I didn't notice. It says it will take a couple days to clear. Hopefully this won't be a problem.
Post by: elton5354 on Tue, 14 April 2015, 00:50:14
Address change within the same country is fine of course or any changes that don't change the weight or price.
Post by: yicaoyimu on Tue, 14 April 2015, 00:59:05
Post by: admiralvorian on Tue, 14 April 2015, 01:04:17
Post by: elton5354 on Tue, 14 April 2015, 01:06:05
PAID! how long do us 2nd-batchers have to wait? (not that Im complaining, there are obviously lots of people that didn't get in at all) just wondering.
A month or so.
Post by: Pemdas on Tue, 14 April 2015, 01:07:13
Post by: Evo_Spec on Tue, 14 April 2015, 01:32:39
Post by: kacase on Tue, 14 April 2015, 01:32:56
Post by: duzeyao on Tue, 14 April 2015, 01:39:53
Looking forward to the kbd and wish I enjoy my first GB in GH
Post by: elton5354 on Tue, 14 April 2015, 01:43:44
i'm currently flying around the globe for work, but I think i'll be able to pay by sunday! Hope thats ok!
That's fine. Payment deadline will be on May 1st.
If anyone is interested here is the weight list..
KG | Top 0.369 | Bottom Al 1.63 | Angle Bottom 0.605 | Flat Bottom 0.214 | PCB 0.142 | SS PLate 0.2 | Alum Plate 0.081 | Plastic Plate 0.042 | Accessories 0.014 | Box weight 0.69 |
Post by: kacase on Tue, 14 April 2015, 02:06:39
Post by: elton5354 on Tue, 14 April 2015, 02:18:51
when do you think shipping will begin?
I'd say 2-3 months from now.
Post by: PunksDead on Tue, 14 April 2015, 02:24:22
"The way my bank account is set up I have a checking account and a saving account and I have to transfer my money to my saving account and thats going to take about 3 business days"
(http://i.imgur.com/SO1g0Wi.jpg)
<3
Post by: pmh1410 on Tue, 14 April 2015, 02:47:51
Thanks Elton ;)
Post by: elton5354 on Tue, 14 April 2015, 02:53:22
Even though I'm not in this GB I would be interested in picking up another plate + PCB to be able to easily swap around my V1 board.bottom plates work on V1?Let me confirm but most likely it is able to
V2 bottoms will fit V1 tops.
Post by: MarkRobbo on Tue, 14 April 2015, 03:42:03
Post by: FreeChemicals on Tue, 14 April 2015, 03:43:02
i'm currently flying around the globe for work, but I think i'll be able to pay by sunday! Hope thats ok!
That's fine. Payment deadline will be on May 1st.
If anyone is interested here is the weight list..
KGTop
0.369Bottom Al
1.63Angle Bottom
0.605Flat Bottom
0.214PCB
0.142SS PLate
0.2Alum Plate
0.081Plastic Plate
0.042Accessories
0.014Box weight
0.69
In the mail I've received it says "Date payment is due 14 Apr 2015", or is it the 1st of May?
Post by: elton5354 on Tue, 14 April 2015, 03:46:35
In the mail I've received it says "Date payment is due 14 Apr 2015", or is it the 1st of May?
It's May 1st, I just didn't want to manually change each invoice's due date. Even making an invoice template doesn't set the due date either..
Post by: pmh1410 on Tue, 14 April 2015, 04:55:10
Post by: Fnzzy on Tue, 14 April 2015, 06:11:59
Post by: MarkRobbo on Tue, 14 April 2015, 06:28:21
Post by: elton5354 on Tue, 14 April 2015, 06:31:22
Post by: Jason_IRL on Tue, 14 April 2015, 07:04:54
I realized I forgot about the stabilizers after I finished invoicing...:facepalm:
already paid, but would be interested in stabilizers as well ;D
Post by: rainb1ood on Tue, 14 April 2015, 07:22:30
Post by: Frizer on Tue, 14 April 2015, 07:58:15
Post by: ctrlX on Tue, 14 April 2015, 08:01:06
Post by: Prankk on Tue, 14 April 2015, 08:05:43
Post by: ph3nomzlol on Tue, 14 April 2015, 08:11:24
I realized I forgot about the stabilizers after I finished invoicing...:facepalm:
Will you modify invoices and re-send? Or additional invoice if we want to add stabs?
Post by: FrostyToast on Tue, 14 April 2015, 08:26:41
Would standard Cherry stabs work?
Post by: duzeyao on Tue, 14 April 2015, 08:28:21
Post by: gravenshard on Tue, 14 April 2015, 08:31:44
Post by: admiralvorian on Tue, 14 April 2015, 08:41:52
PAID! how long do us 2nd-batchers have to wait? (not that Im complaining, there are obviously lots of people that didn't get in at all) just wondering.
A month or so.
Oh wow that's awesome!
Also in for a set or two of stabs if that happens.
Post by: lionblinds on Tue, 14 April 2015, 09:09:52
Post by: ekw808 on Tue, 14 April 2015, 09:24:23
Post by: MarkRobbo on Tue, 14 April 2015, 09:39:06
Wow dam, group buy finishing in less than 4 days...stupid tax season..
Was less than a day to 60 orders if I recall correctly! :eek:
Post by: wlhlm on Tue, 14 April 2015, 09:43:02
Yeah, < 15 hours :eek:Wow dam, group buy finishing in less than 4 days...stupid tax season..
Was less than a day to 60 orders if I recall correctly! :eek:
Post by: frostylove on Tue, 14 April 2015, 10:00:07
Waiting this beauty with my new octagon.
[attachimg=1]
Post by: ramnes on Tue, 14 April 2015, 10:16:11
Post by: laguar on Tue, 14 April 2015, 10:23:04
Post by: r0mIe_Ng on Tue, 14 April 2015, 10:23:16
Post by: ph3nomzlol on Tue, 14 April 2015, 10:47:31
Let us know, Elton! We wait with bated breath :-X
Post by: Lastpilot on Tue, 14 April 2015, 11:15:53
Post by: monotagary on Tue, 14 April 2015, 11:32:24
Post by: Sed8op8 on Tue, 14 April 2015, 11:42:57
I'll wait for the update on how stabilizers are going - also tempted to add on an Alps pcb/plate. Only 5 people ordered it?! Matias says they should be coming out with keycap options soon so I might go ahead and invest in the PCB now. ^-^I second that . Also Lastpilot I have a question for you I'm PM'ing now.
Post by: ryptide11 on Tue, 14 April 2015, 12:04:57
Post by: tjweir on Tue, 14 April 2015, 13:27:29
Keyboard innovation, who would have thunk it?
Post by: MarkRobbo on Tue, 14 April 2015, 13:56:32
Post by: orcinus on Tue, 14 April 2015, 15:26:48
Post by: tuantruong on Tue, 14 April 2015, 15:48:25
Post by: ctrlX on Wed, 15 April 2015, 05:03:51
Thanks in advance.
Post by: FreeChemicals on Wed, 15 April 2015, 06:00:13
I am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).
Thanks in advance.
You can't go wrong with 2x3x4 LEDs afaik. I bought a bunch of them @ zeal for my sprit build :)
Post by: MarkRobbo on Wed, 15 April 2015, 06:36:03
Post by: wlhlm on Wed, 15 April 2015, 07:02:20
Yep. You can also get them for $6 on aliexpress but shipping can take up to a monthThis keyboard won't arrive before a month either.
I am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).I'd get them from Aliexpress as well:
Thanks in advance.
http://www.aliexpress.com/store/group/Rectangular-square-led/629743_251765645.html
Post by: ctrlX on Wed, 15 April 2015, 07:14:10
Yep. You can also get them for $6 on aliexpress but shipping can take up to a monthThis keyboard won't arrive before a month either.I am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).I'd get them from Aliexpress as well:
Thanks in advance.
http://www.aliexpress.com/store/group/Rectangular-square-led/629743_251765645.html
I am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).
Thanks in advance.
You can't go wrong with 2x3x4 LEDs afaik. I bought a bunch of them @ zeal for my sprit build :)
Thnx a bunch for the suggestions. Probably go with Zeal in the end as I will buy some SIP sockets and other switch accessories from them. So I will not be able dodge any shipping costs anyway.
Post by: FreeChemicals on Wed, 15 April 2015, 07:31:39
Yep. You can also get them for $6 on aliexpress but shipping can take up to a monthThis keyboard won't arrive before a month either.I am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).I'd get them from Aliexpress as well:
Thanks in advance.
http://www.aliexpress.com/store/group/Rectangular-square-led/629743_251765645.htmlI am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).
Thanks in advance.
You can't go wrong with 2x3x4 LEDs afaik. I bought a bunch of them @ zeal for my sprit build :)
Thnx a bunch for the suggestions. Probably go with Zeal in the end as I will buy some SIP sockets and other switch accessories from them. So I will not be able dodge any shipping costs anyway.
If you buy the SIP sockets from zeal, don't forget to order them x2 (because he sells them per 130, not enough to cover every switch.
Post by: ctrlX on Wed, 15 April 2015, 07:38:54
If you buy the SIP sockets from zeal, don't forget to order them x2 (because he sells them per 130, not enough to cover every switch.
Good point. Didn't think of that so thank you once again! :D
Post by: wlhlm on Wed, 15 April 2015, 08:12:40
If you want to try:Yep. You can also get them for $6 on aliexpress but shipping can take up to a monthThis keyboard won't arrive before a month either.I am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).I'd get them from Aliexpress as well:
Thanks in advance.
http://www.aliexpress.com/store/group/Rectangular-square-led/629743_251765645.htmlI am gradually planning my build of the Orion V2 and it is my first custom build. So I humbly ask the pros here, what type of LEDs does the pre-soldered diodes work with? I am currently looking at buying the LEDs from Zeal (http://zealpc.net/collections/accessories/products/leds).
Thanks in advance.
You can't go wrong with 2x3x4 LEDs afaik. I bought a bunch of them @ zeal for my sprit build :)
Thnx a bunch for the suggestions. Probably go with Zeal in the end as I will buy some SIP sockets and other switch accessories from them. So I will not be able dodge any shipping costs anyway.
I got my sockets from Taobao (http://item.taobao.com/item.htm?id=43516784288). ¥0.10 a piece (500 = $10!). Zeal's are a bit pricey imo.
Post by: FrostyToast on Wed, 15 April 2015, 08:22:43
Post by: wlhlm on Wed, 15 April 2015, 08:32:28
The thing about sockets from Zeal is that they are already clipped of their plastic housings which is a ***** to do yourself.From the pictures, I'd say they're removed as well. The poorly google-translated description doesn't say anything specific though.
They are on the way and I'll drop an update once they arrive.
Post by: FreeChemicals on Wed, 15 April 2015, 09:36:49
The thing about sockets from Zeal is that they are already clipped of their plastic housings which is a ***** to do yourself.
That doesnt seem to be that bad: just use a clipper, see https://geekhack.org/index.php?topic=51792.msg1179087#msg1179087
I've paid $10 last time, for 130. This time I've ordered them from ebay, 400x @ ~6$. I might have to clip them myself, but I don't mind.
Post by: CyriusG on Wed, 15 April 2015, 10:27:30
Post by: Want on Wed, 15 April 2015, 14:42:52
Has anyone thought about blocking the two hole in the bottom case so that light only shines through the acrylic insert?
You might be able to put a strip of eletrical tape on either the insert or the bottom case to block the light. Probably isn't too thick, and should do the job.
Elton, if one were to put a dampening mat between the PCB and acrylic angled bottom, with cutouts around the LEDs, would it block out a significant amount of light?
Post by: Fnzzy on Wed, 15 April 2015, 19:06:08
The thing about sockets from Zeal is that they are already clipped of their plastic housings which is a ***** to do yourself.
That doesnt seem to be that bad: just use a clipper, see https://geekhack.org/index.php?topic=51792.msg1179087#msg1179087
I've paid $10 last time, for 130. This time I've ordered them from ebay, 400x @ ~6$. I might have to clip them myself, but I don't mind.
Can you show me where you ordered them? I an planning on putting SIP sockets in the orion v2 and I didn't buy some at nuclears GB (because I thought I never need them, smart me...).
Post by: IonutZ on Wed, 15 April 2015, 19:15:03
Post by: radio_killah on Wed, 15 April 2015, 19:27:28
How well do the LEDs stay in the SIP sockets? Have any of you run into an issue where they fall out?
As long as you don't trim down the legs of the LED too much they will stay in without a problem
Post by: Bromono on Wed, 15 April 2015, 19:39:12
Post by: rainb1ood on Wed, 15 April 2015, 19:42:03
(http://i.imgur.com/JOKM0cU.png)
Post by: LONGZILLA on Wed, 15 April 2015, 20:11:04
Even though I'm not in this GB I would be interested in picking up another plate + PCB to be able to easily swap around my V1 board.bottom plates work on V1?Let me confirm but most likely it is able to
V2 bottoms will fit V1 tops.
Thanks
Post by: elton5354 on Wed, 15 April 2015, 20:50:10
Maybe you can get some here? https://geekhack.org/index.php?topic=70990.0
Post by: Lastpilot on Wed, 15 April 2015, 21:17:52
Post by: Evo_Spec on Wed, 15 April 2015, 21:18:16
How well do the LEDs stay in the SIP sockets? Have any of you run into an issue where they fall out?You could turn it upside down and shake it and they shouldn't fall out. If you want more security use 2x3x4 led's since those friction fit into the top housing. Kind of makes it a ***** to remove or swap though lol.
Either way it should absolutely not fall out under normal circumstances.
Post by: wangbwhz on Thu, 16 April 2015, 00:03:25
Post by: FreeChemicals on Thu, 16 April 2015, 02:25:24
How well do the LEDs stay in the SIP sockets? Have any of you run into an issue where they fall out?
As long as you don't trim down the legs of the LED too much they will stay in without a problem
Zeal sent me this picture when I started building my previous board:
(http://i.imgur.com/bHQNtcul.jpg) (http://imgur.com/bHQNtcu)
Quote from: Zeal
ANOTHER IMPORTANT NOTE! Almost forgot. I HIGHLY RECOMMEND you insert the clipped LEDs (cut with flush cutters noting polarity a hair under the two bumps on the legs) INTO THE SIP SOCKET BEFORE SOLDERING. This keeps the pins straight when you solder SIP sockets onto the PCB. If you don't you'll have a hell of a time desoldering. Some people insert a new uncut LED into the SIP to align. I find it silly that you're doing two steps when you can already have the LED installed into the switch! Make sure the 2x3x4mm LEDs are sitting flat inside the indent of the Chery switch. If it's not sitting flat, then it's not all the way in.
Cut on red line
If you cut above the red line, the LEDs are able to fall out of their sockets.
Post by: wlhlm on Thu, 16 April 2015, 02:28:31
Quote from: Zeal
ANOTHER IMPORTANT NOTE! Almost forgot. I HIGHLY RECOMMEND you insert the clipped LEDs (cut with flush cutters noting polarity a hair under the two bumps on the legs) INTO THE SIP SOCKET BEFORE SOLDERING. This keeps the pins straight when you solder SIP sockets onto the PCB. If you don't you'll have a hell of a time desoldering. Some people insert a new uncut LED into the SIP to align. I find it silly that you're doing two steps when you can already have the LED installed into the switch! Make sure the 2x3x4mm LEDs are sitting flat inside the indent of the Chery switch. If it's not sitting flat, then it's not all the way in.Good tip from Zeal, though I would use a piece of wire instead of the LED just to be sure not to damage it by overheating.
Cut on red line
Post by: Ahkrael on Thu, 16 April 2015, 03:00:32
For switches, I'm going with the plastic plate, and I have several options for stem/springs. I have 90 gat browns and 90 gat clears on the way - I should of ordered the blacks, but I have 62g activation weight springs I can swap into the clears, to get a black-esque feel. I feel like I should grab some real 62g korean springs (I got mine from assdrop - they butchered that spring groupbuy, wasn't even a great price...). The only other thing I'm missing for an option, are the cherry MX clear stems... I have 1 from a switch-tester, and I loved the clear stem + black spring (panda clears I believe).
Does anyone know a vendor that sells cherry mx Clears (stems or switches) that is actually in stock - or any ETA on MK.com or Zeal?
Post by: Evo_Spec on Thu, 16 April 2015, 03:06:04
This is what I figured out and did during my build and all 87 led's are fine, even if they weren't they're pretty cheap anyways and you'll always definitely have enough since they're mostly sold in 100's so you'll either have 13 or 90 extra led's to use.Quote from: ZealANOTHER IMPORTANT NOTE! Almost forgot. I HIGHLY RECOMMEND you insert the clipped LEDs (cut with flush cutters noting polarity a hair under the two bumps on the legs) INTO THE SIP SOCKET BEFORE SOLDERING. This keeps the pins straight when you solder SIP sockets onto the PCB. If you don't you'll have a hell of a time desoldering. Some people insert a new uncut LED into the SIP to align. I find it silly that you're doing two steps when you can already have the LED installed into the switch! Make sure the 2x3x4mm LEDs are sitting flat inside the indent of the Chery switch. If it's not sitting flat, then it's not all the way in.Good tip from Zeal, though I would use a piece of wire instead of the LED just to be sure not to damage it by overheating.
Cut on red line
Post by: wlhlm on Thu, 16 April 2015, 03:06:49
Does anyone know a vendor that sells cherry mx Clears (stems or switches) that is actually in stock - or any ETA on MK.com or Zeal?
MK.com says (https://geekhack.org/index.php?topic=31221.msg1716624#msg1716624) 12 months (Cherry lead times are crazy). I recently got a pack of Clears from sprit.
Post by: Ahkrael on Thu, 16 April 2015, 03:10:00
Wow. Maybe I'll look to order a keyboard with clears and salvage some.. I was thinking to do linears on modifiers anyways. The pok3r just came out, looks interesting for an alternate board.Does anyone know a vendor that sells cherry mx Clears (stems or switches) that is actually in stock - or any ETA on MK.com or Zeal?
MK.com says (https://geekhack.org/index.php?topic=31221.msg1716624#msg1716624) 12 months (Cherry lead times are crazy). I recently got a pack of Clears from sprit.
Post by: ctrlX on Thu, 16 April 2015, 05:12:34
Plate mounted MX clears seem to be out of stock in most places. PCB mounted MX clears seem to be available at some places, i.e. winkeyless.kr and www.gonskeyboardworks.com
This brings up another question. Looking at the 3D render of the PCB it seems to be prepped for PCB mounted switches. Can anyone confirm? Is there a reason to opt for the plate mounted switches instead of PCB mounted? A PCB mounted switch should work with a plate as long as the PCB has holes for the stems right?
Post by: Ahkrael on Thu, 16 April 2015, 06:35:53
Post by: FrostyToast on Thu, 16 April 2015, 06:38:02
Really good tips/suggestions here for the novice. Thank you for that! :thumb:
Plate mounted MX clears seem to be out of stock in most places. PCB mounted MX clears seem to be available at some places, i.e. winkeyless.kr and www.gonskeyboardworks.com
This brings up another question. Looking at the 3D render of the PCB it seems to be prepped for PCB mounted switches. Can anyone confirm? Is there a reason to opt for the plate mounted switches instead of PCB mounted? A PCB mounted switch should work with a plate as long as the PCB has holes for the stems right?
PCB mounted switches can have the legs clipped and that will make them the exact same as plate mount.
Post by: FreeChemicals on Thu, 16 April 2015, 06:46:06
I have a newbie question here - regarding the controller programming. Is there a custom software to use for this board? I know GON has a gui, and I've seen others, just wondering what will be compatible with the V2.
I assume the Orion V2 will be added to the O2D KeyMapper, take a look at http://duck0113.tistory.com/category/%E2%98%85Firmware%20Program
Post by: Latin00032 on Thu, 16 April 2015, 07:56:14
Can I ask where I am on the list?
Post by: ph3nomzlol on Thu, 16 April 2015, 08:53:03
I have a newbie question here - regarding the controller programming. Is there a custom software to use for this board? I know GON has a gui, and I've seen others, just wondering what will be compatible with the V2.
I assume the Orion V2 will be added to the O2D KeyMapper, take a look at http://duck0113.tistory.com/category/%E2%98%85Firmware%20Program
I do know that Orion (at least V1) is supported by Easy AVR programmer here:
https://geekhack.org/index.php?topic=51252.0
I wonder if that support will extend to V2? Does anyone know if the controller is the same, etc.?
Post by: 3Love on Fri, 17 April 2015, 00:34:00
Post by: elton5354 on Fri, 17 April 2015, 07:04:25
I have a newbie question here - regarding the controller programming. Is there a custom software to use for this board? I know GON has a gui, and I've seen others, just wondering what will be compatible with the V2.
I assume the Orion V2 will be added to the O2D KeyMapper, take a look at http://duck0113.tistory.com/category/%E2%98%85Firmware%20Program
I do know that Orion (at least V1) is supported by Easy AVR programmer here:
https://geekhack.org/index.php?topic=51252.0
I wonder if that support will extend to V2? Does anyone know if the controller is the same, etc.?
It is the same controller on the V2
Post by: ph3nomzlol on Fri, 17 April 2015, 09:49:39
I have a newbie question here - regarding the controller programming. Is there a custom software to use for this board? I know GON has a gui, and I've seen others, just wondering what will be compatible with the V2.
I assume the Orion V2 will be added to the O2D KeyMapper, take a look at http://duck0113.tistory.com/category/%E2%98%85Firmware%20Program
I do know that Orion (at least V1) is supported by Easy AVR programmer here:
https://geekhack.org/index.php?topic=51252.0
I wonder if that support will extend to V2? Does anyone know if the controller is the same, etc.?
It is the same controller on the V2
Fantastic! I became well-acquainted with the Easy AVR program from fiddling with my Phantom; very nice!
Post by: effectiveduck on Sun, 19 April 2015, 12:35:37
Post by: Want on Sun, 19 April 2015, 13:09:14
What were the exact weights of each item again?
KGTop
0.369Bottom Al
1.63Angle Bottom
0.605Flat Bottom
0.214PCB
0.142SS PLate
0.2Alum Plate
0.081Plastic Plate
0.042Accessories
0.014Box weight
0.69
Cool stuff.
Post by: effectiveduck on Sun, 19 April 2015, 13:13:13
What were the exact weights of each item again?
KGTop
0.369Bottom Al
1.63Angle Bottom
0.605Flat Bottom
0.214PCB
0.142SS PLate
0.2Alum Plate
0.081Plastic Plate
0.042Accessories
0.014Box weight
0.69
Cool stuff.
Thanks.
Post by: missalaire on Sun, 19 April 2015, 15:01:27
Post by: wlhlm on Tue, 21 April 2015, 01:15:14
Post by: appleonama on Tue, 21 April 2015, 03:45:15
everywhere seems to be out of stock
also any place to get sticker switches
Post by: wlhlm on Tue, 21 April 2015, 04:38:33
anyone know where to get any cherry mx clear switches?I recently ordered some from sprit. Maybe, he has some left.
everywhere seems to be out of stock
also any place to get sticker switches
Post by: missalaire on Tue, 21 April 2015, 14:23:30
anyone know where to get any cherry mx clear switches?
everywhere seems to be out of stock
also any place to get sticker switches
You can order them from GON.
Post by: kingslenkds on Tue, 21 April 2015, 14:51:48
The next group of group purchase will be when? I'm sorry this purchase does not catch up with, if there is a new message, please tell me, thank you!
Post by: Michael on Tue, 21 April 2015, 15:06:41
ELTON
The next group of group purchase will be when? I'm sorry this purchase does not catch up with, if there is a new message, please tell me, thank you!
wat (http://i.imgur.com/XMTIbdL.png)
Post by: Defect on Wed, 22 April 2015, 10:33:05
Post by: FrostyToast on Wed, 22 April 2015, 10:37:32
In need of Alps PCB and plate if anyone is here for the case only. PM me please.
Since the ALPS stuff was completely optional I highly doubt that people have extras.
No idea if Elton will allow order changes but that might be the only option.
Post by: r0mIe_Ng on Thu, 23 April 2015, 13:10:17
Post by: Defect on Thu, 23 April 2015, 20:12:04
In need of Alps PCB and plate if anyone is here for the case only. PM me please.
Since the ALPS stuff was completely optional I highly doubt that people have extras.
No idea if Elton will allow order changes but that might be the only option.
I'm hoping someone can modify their order and let me piggy back. I'll pay for shipping of course.
Post by: kacase on Fri, 24 April 2015, 06:10:43
Post by: MarkRobbo on Fri, 24 April 2015, 07:09:05
Hi Elton, I have finally payed the invoice. Sorry for the delay. The paypal shipping address is however not the right one. Will you use the one from the webform?
From order form:
This will be used to ship your item(s). I will not be using your PayPal shipping address.
Post by: wakko on Sat, 25 April 2015, 00:50:40
Post by: monotagary on Sat, 25 April 2015, 13:51:30
In need of Alps PCB and plate if anyone is here for the case only. PM me please.
Since the ALPS stuff was completely optional I highly doubt that people have extras.
No idea if Elton will allow order changes but that might be the only option.
I'm hoping someone can modify their order and let me piggy back. I'll pay for shipping of course.
I don't think Elton is letting anyone change their order at this point since invoices already went out.
Post by: TLSC.wipeOut on Sat, 25 April 2015, 14:45:25
Post by: Sed8op8 on Sat, 25 April 2015, 15:05:57
Will there be a second round of these?i hope so or a viper v2
Post by: Jason_IRL on Sat, 25 April 2015, 21:22:02
Post by: elton5354 on Sat, 25 April 2015, 22:35:58
Does anyone know a timeline of when the first round will ship? Been checking the thread often (maybe I missed something?)
I'd say around 2 months.
Green PCB :blank:
(http://i.imgur.com/W0BVjtJ.jpg)
(http://i.imgur.com/p9axzBX.jpg)
Post by: MarkRobbo on Sun, 26 April 2015, 05:25:47
Post by: Fnzzy on Sun, 26 April 2015, 06:41:20
Post by: CyriusG on Sun, 26 April 2015, 06:49:54
Post by: MarkRobbo on Sun, 26 April 2015, 07:44:51
I've been curious how the extra LEDs are mounted in the case. Are they mounted directly on the PCB with spacers or is there a mounting device on the case itself?
There are SMD mount RGB LEDs on the back of the PCB
Post by: elton5354 on Sun, 26 April 2015, 09:08:53
Ooh. I was hoping for white, but green is definitely better than red. Actually the green will probably look nice under the plastic plate
White is for the ALPs PCB
Does this mean we WILL get a green PCB? All the pictures we have seen so far had a red PCB and I assumed that we will get that.
I could safely assume so since they made all the pcbs green for Octagon. Sorry about that.
There are about 3 pictures with the red PCB
http://cfile25.uf.tistory.com/image/22567936551F48751764AB
It was probably a V1 and that they haven't made the PCB yet for V2.
I've been curious how the extra LEDs are mounted in the case. Are they mounted directly on the PCB with spacers or is there a mounting device on the case itself?
The ones on top of the case? You could use 2x3x4mm or 3mm round ones you use for your switch LEDs.
Post by: CyriusG on Sun, 26 April 2015, 09:35:07
Post by: Lastpilot on Mon, 27 April 2015, 10:56:56
Post by: rainb1ood on Mon, 27 April 2015, 13:31:33
On my Octagon I was able to buy a few on Amazon but the seller ran out of stock at the moment.
Post by: r0mIe_Ng on Mon, 27 April 2015, 14:22:23
Post by: kacase on Mon, 27 April 2015, 17:13:42
Post by: orcinus on Mon, 27 April 2015, 18:23:15
Post by: Lpwl on Mon, 27 April 2015, 18:53:53
Where do you guys get your 1.8mm LEDs? If eBay, which seller?Try this vendor (on eBay) : colorfulplace888 (http://stores.ebay.com/colorfulplace888)
On my Octagon I was able to buy a few on Amazon but the seller ran out of stock at the moment.
You should look for the "New 1.8mm __color__ Water Clear [...]" LEDs ;)
EDIT : Fixed the link.
Post by: rainb1ood on Mon, 27 April 2015, 19:02:37
Where do you guys get your 1.8mm LEDs? If eBay, which seller?Try this vendor (on eBay) : colorfulplace888 (http://m.ebay.com/seller?sid=colorfulplace888)
On my Octagon I was able to buy a few on Amazon but the seller ran out of stock at the moment.
You should look for the "New 1.8mm __color__ Water Clear [...]" LEDs ;)
Thank you sir!
Post by: ramnes on Wed, 29 April 2015, 09:36:44
Post by: missalaire on Wed, 29 April 2015, 20:22:01
Post by: seedvd on Wed, 29 April 2015, 20:42:35
What size spacebar stabilizer does this use?
Since you ordered a Winkey layout board, you can use either 6.25u or 7u PCB mount stabilizer.
Post by: seedvd on Wed, 29 April 2015, 21:07:13
(http://i.imgur.com/kFcWIJK.jpg)
(http://i.imgur.com/jIMzddj.jpg)
Post by: Fnzzy on Thu, 30 April 2015, 05:45:21
Post by: Evo_Spec on Thu, 30 April 2015, 06:31:26
I wonder if normal 2x3x4 LEDs fit in there. Sky blue dots above arrow keys would be neat, indeed!
the LED legs are the same size so there's no reason that they wouldn't work.
Post by: rainb1ood on Thu, 30 April 2015, 07:34:07
Post by: wlhlm on Thu, 30 April 2015, 12:26:03
Post by: wangbwhz on Thu, 30 April 2015, 12:48:52
Post by: wlhlm on Thu, 30 April 2015, 12:50:53
4 unpaid.. do i get chance to go in> ? wan to know the resultProbably not. The order form is still open and I guess elton will just pick the next person from the list.
Post by: ramnes on Thu, 30 April 2015, 12:56:05
Now that I got the money, I'd really like to know about shipping before paying (cf. my question some posts before). :)
Post by: elton5354 on Thu, 30 April 2015, 20:20:25
Will it be possible to send the package as gift, with an indicated value under 100$?
Yeah, it will be. I have never paid any customs before receiving these from SK.
Post by: ramnes on Fri, 01 May 2015, 08:08:27
Will it be possible to send the package as gift, with an indicated value under 100$?
Yeah, it will be. I have never paid any customs before receiving these from SK.
Okay, great. Paid. Thanks for your patience Elton. :cool:
Post by: wlhlm on Fri, 01 May 2015, 08:11:23
Post by: rsadek on Fri, 01 May 2015, 09:55:35
Only Crabby_B, reaxas, and DelKey left...
<skip to rsadek, skip to rsadek, skip to rsadek>
;)
Post by: ramnes on Fri, 01 May 2015, 15:56:51
Post by: elton5354 on Sat, 02 May 2015, 23:54:27
Well, there are 2 spots..who wants to be next? ;)
Post by: HTN47 on Sun, 03 May 2015, 00:50:54
Post by: rsadek on Sun, 03 May 2015, 00:55:50
Post by: Dreamre on Sun, 03 May 2015, 01:12:08
There will be a lot of foam materials..
Well, there are 2 spots..who wants to be next? ;)
I want it!!!
Post by: wangbwhz on Sun, 03 May 2015, 10:03:52
wait what!!! there are spots open for this buy? :eek:i want it !!! and i think i am 60!
Post by: elton5354 on Sun, 03 May 2015, 11:07:40
Post by: elton5354 on Sun, 03 May 2015, 11:09:22
wait what!!! there are spots open for this buy? :eek:i want it !!! and i think i am 60!
You're the 3rd..lol
Post by: radio_killah on Sun, 03 May 2015, 11:09:44
I'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(Lol that's cold Elton. I sent you a pm though not sure if you got it or not. Oh well.
Post by: elton5354 on Sun, 03 May 2015, 11:12:39
I'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(Lol that's cold Elton. I sent you a pm though not sure if you got it or not. Oh well.
Yeah, I received it. They are only doing 60 sets for GH. TC has group buys in China and SK as well so they have massive orders.
Post by: radio_killah on Sun, 03 May 2015, 11:19:25
I'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(Lol that's cold Elton. I sent you a pm though not sure if you got it or not. Oh well.
Yeah, I received it. They are only doing 60 sets for GH. TC has group buys in China and SK as well so they have massive orders.
Ahh okay. Thanks anyways :thumb:
Post by: malcomkern on Sun, 03 May 2015, 12:34:10
Post by: Want on Sun, 03 May 2015, 13:01:46
I'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(Lol that's cold Elton. I sent you a pm though not sure if you got it or not. Oh well.
Yeah, I received it. They are only doing 60 sets for GH. TC has group buys in China and SK as well so they have massive orders.
So are the total numbers available? Would be cool to know the final amount of Orion V2s in the world :)
Post by: rsadek on Sun, 03 May 2015, 20:15:29
I'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(
It hurts in my feels. Why u make me sad.
I'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(Lol that's cold Elton. I sent you a pm though not sure if you got it or not. Oh well.
Yeah, I received it. They are only doing 60 sets for GH. TC has group buys in China and SK as well so they have massive orders.
Wut. Tell them to make a few more. They will say yes.
Post by: FreeChemicals on Mon, 04 May 2015, 05:22:11
Post by: FrostyToast on Mon, 04 May 2015, 07:29:25
I'm having a hard time deciding which type of switch I'll order, but that made me think: why doesn't the plate supports switchtop removal in the first place? Imo, that would only be reasonable for such a premium keyboard.
Some people would think that adding the notches for switch top removal decreases stability. While this may be untrue, these same people also think that stickers improve stability meaning that they will do whatever to increase feeling.
One would also think that for such a premium board you would take your time to plan what switches to put in.
It also helps to reduce costs significantly, so that's just a bonus for everyone.
Post by: Jason_IRL on Mon, 04 May 2015, 07:31:59
I'm having a hard time deciding which type of switch I'll order, but that made me think: why doesn't the plate supports switchtop removal in the first place? Imo, that would only be reasonable for such a premium keyboard.
Easy, Gateron switches of your favorite variety. :thumb:
Post by: wlhlm on Mon, 04 May 2015, 07:35:04
No MX Clears so far, sadly :'(I'm having a hard time deciding which type of switch I'll order, but that made me think: why doesn't the plate supports switchtop removal in the first place? Imo, that would only be reasonable for such a premium keyboard.
Easy, Gateron switches of your favorite variety. :thumb:
Post by: ramnes on Mon, 04 May 2015, 07:37:18
Post by: wangbwhz on Mon, 04 May 2015, 09:09:02
what a pity,hope jaemzp does not payI'm just kidding. I'm just going to PM the next in line if they still want it. Sorry :(Lol that's cold Elton. I sent you a pm though not sure if you got it or not. Oh well.
Yeah, I received it. They are only doing 60 sets for GH. TC has group buys in China and SK as well so they have massive orders.
Ahh okay. Thanks anyways :thumb:
Post by: asgeirtj on Thu, 07 May 2015, 13:06:42
On the red winkeyless board showcased: why is the space between ctrl alt gray? Is it not a part of the case? Is it just the plate? If it isn't a part of the case then why do you need to choose winkey or winkeyless case? If it is a part of the case why not have it red also?
Post by: yicaoyimu on Thu, 07 May 2015, 13:16:03
Show Image(http://i.imgur.com/DoO9Egu.jpg)
On the red winkeyless board showcased: why is the space between ctrl alt gray? Is it not a part of the case? Is it just the plate? If it isn't a part of the case then why do you need to choose winkey or winkeyless case? If it is a part of the case why not have it red also?
The red one has ALPS inside. So it's kind of different.
Post by: FrostyToast on Thu, 07 May 2015, 13:19:00
Show Image(http://i.imgur.com/DoO9Egu.jpg)
On the red winkeyless board showcased: why is the space between ctrl alt gray? Is it not a part of the case? Is it just the plate? If it isn't a part of the case then why do you need to choose winkey or winkeyless case? If it is a part of the case why not have it red also?
I would assume it's a prototyping thing.
I don't know if I have seen a single WKL case yet. They probably had all winkey tops ordered.
Post by: cooldiscretion on Thu, 07 May 2015, 13:23:15
Post by: wlhlm on Thu, 07 May 2015, 13:24:19
I'm pretty sure its because that is the winkey case + ALPs plate - not a likely combo in my opinion. If someone goes ALPs they would most likely get the winkeyless case and then that recess wouldn't be there. It would have the red case metal extend over where the winkey would be.Is this because most ALPS keysets are WKL?
Post by: cooldiscretion on Thu, 07 May 2015, 13:28:28
Post by: orcinus on Thu, 07 May 2015, 17:16:23
On the red winkeyless board showcased: why is the space between ctrl alt gray? Is it not a part of the case? Is it just the plate? If it isn't a part of the case then why do you need to choose winkey or winkeyless case? If it is a part of the case why not have it red also?
It's a prototype with a cover in place of the win key.
This is what the winkeyless case looks like:
(http://cfile29.uf.tistory.com/image/226D364C54FAB25723D37C)
(http://cfile6.uf.tistory.com/image/223E764F54FAB25A389727)
Post by: elton5354 on Fri, 08 May 2015, 10:29:35
(http://kbdlab.co.kr/files/attach/images/340/117/711/002/a474ca7540c3fef1da67be107b59c662.jpg)
(http://kbdlab.co.kr/files/attach/images/340/117/711/002/49fadb496e5d38e50c0d50e04a2ab87c.jpg)
(http://kbdlab.co.kr/files/attach/images/340/117/711/002/e065d078e3c5405c24d0482b8d60bdf1.jpg)
(http://kbdlab.co.kr/files/attach/images/340/117/711/002/76696874841d27ef307604ca361b7a61.jpg)
Post by: wlhlm on Fri, 08 May 2015, 10:32:45
Wish there was an option for this...Hmm, that would be awesome! Can you link to the thread?Show Image(http://kbdlab.co.kr/files/attach/images/340/117/711/002/a474ca7540c3fef1da67be107b59c662.jpg)Show Image(http://kbdlab.co.kr/files/attach/images/340/117/711/002/49fadb496e5d38e50c0d50e04a2ab87c.jpg)Show Image(http://kbdlab.co.kr/files/attach/images/340/117/711/002/e065d078e3c5405c24d0482b8d60bdf1.jpg)Show Image(http://kbdlab.co.kr/files/attach/images/340/117/711/002/76696874841d27ef307604ca361b7a61.jpg)
Post by: elton5354 on Fri, 08 May 2015, 10:36:56
I think it is just an one off made by another member.
Post by: wlhlm on Fri, 08 May 2015, 10:41:43
http://kbdlab.co.kr/index.php?document_srl=2711117&mid=board_Lsno50We should form a mob and persuade Duck, but I guess it's too late at this point and would increase the cost of the Aluminium bottom (though I wouldn't have a problem with that)... :rolleyes: :'(
I think it is just an one off made by another member.
Post by: Fnzzy on Tue, 12 May 2015, 12:43:32
Post by: Want on Tue, 12 May 2015, 13:14:28
Nice.
I'm really looking forward to the Orion v2, but I've been hesitant on wether I made the right choice on colour ever since ordering.
When's the last date to change colours, Elton?
Post by: orcinus on Tue, 12 May 2015, 16:45:49
Got switches, got LEDs, got stabs...
Come to papa.
Post by: wlhlm on Tue, 12 May 2015, 16:48:50
You're well prepared sir!Show Image(https://dl.dropboxusercontent.com/u/1702513/Photo%2012-05-15%2023%2043%2001.jpg)
Got switches, got LEDs, got stabs...
Come to papa.
I still have to get some LEDs and am waiting for my keycaps and USB cable.
Post by: appleonama on Tue, 12 May 2015, 17:13:14
where did you get clearsShow Image(https://dl.dropboxusercontent.com/u/1702513/Photo%2012-05-15%2023%2043%2001.jpg)
Got switches, got LEDs, got stabs...
Come to papa.
Post by: MarkRobbo on Tue, 12 May 2015, 17:17:15
where did you get clearsShow Image(https://dl.dropboxusercontent.com/u/1702513/Photo%2012-05-15%2023%2043%2001.jpg)
Got switches, got LEDs, got stabs...
Come to papa.
Looks like GON's work to me! Could be wrong though...
Post by: orcinus on Tue, 12 May 2015, 17:22:48
White LEDs (if anyone was wondering).
Post by: elton5354 on Tue, 12 May 2015, 20:44:59
I'd say end of this week
Nice.
I'm really looking forward to the Orion v2, but I've been hesitant on wether I made the right choice on colour ever since ordering.
When's the last date to change colours, Elton?
Post by: FreeChemicals on Wed, 13 May 2015, 05:04:59
I'd say end of this week
Nice.
I'm really looking forward to the Orion v2, but I've been hesitant on wether I made the right choice on colour ever since ordering.
When's the last date to change colours, Elton?
Would it still be possible to change the plate I ordered (asked for alu, would like a steel version)?
Post by: elton5354 on Wed, 13 May 2015, 09:23:35
Post by: FreeChemicals on Wed, 13 May 2015, 10:04:03
Yes
If you would be so kind to change my order, that would be terrific, (mmkay ;D).
Excuse me for the hassle, though.
Post by: elton5354 on Fri, 15 May 2015, 18:00:42
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
Post by: MarkRobbo on Fri, 15 May 2015, 18:26:47
Think I'm set though, I got all my changes from being indecisive over with early.
Post by: Latin00032 on Fri, 15 May 2015, 19:11:52
Am I still on the list?
I forgot if I am.
Post by: rainb1ood on Fri, 15 May 2015, 20:14:27
Post by: elton5354 on Sat, 16 May 2015, 04:05:03
Elton,
Am I still on the list?
I forgot if I am.
On the waiting list? Probably, but no point right now. :-X
Here's a video on the indicator LEDs
Post by: Want on Sat, 16 May 2015, 05:33:45
Here's a video on the indicator LEDs
Nice!
Question: How much control do we have over the indicator LEDs and the LED cluster above the arrows?
I'd prefer to have the indicator LEDs on when caps etc is off - reversed compared to standard, and have the LED cluster on at all times. But I understand it may not be a priority.
Post by: FreeChemicals on Sat, 16 May 2015, 06:10:47
Here's a video on the indicator LEDs
Nice!
Question: How much control do we have over the indicator LEDs and the LED cluster above the arrows?
I'd prefer to have the indicator LEDs on when caps etc is off - reversed compared to standard, and have the LED cluster on at all times. But I understand it may not be a priority.
I believe this would be a firmware related question. Easy AVR supports the Orion v1, but it didn't include those LED clusters. You could make a request to add LED support, see https://geekhack.org/index.php?topic=51252.0
Thanks for the update elton, it looks stunning!
Post by: Fnzzy on Sat, 16 May 2015, 06:49:09
Post by: rainb1ood on Sat, 16 May 2015, 10:58:02
Oh yes black top housing looking so good. Can any owner of the Octagon tell me if you can set the RGB LEDs on the back to a single custom color instead of rotating through many colors?
This is what I've been trying to figure out with 02D Keymapper with Octagon and will probably be figuring out on this upcoming Orion V2 :D
Post by: tjweir on Sat, 16 May 2015, 11:41:57
Oh yes black top housing looking so good. Can any owner of the Octagon tell me if you can set the RGB LEDs on the back to a single custom color instead of rotating through many colors?
This is what I've been trying to figure out with 02D Keymapper with Octagon and will probably be figuring out on this upcoming Orion V2 :D
With tmk on an Octagon you get on/off control of red, green and blue individually.
Not sure about the O2D firmware, sorry.
Post by: wlhlm on Tue, 19 May 2015, 01:55:36
Post by: Lpwl on Tue, 19 May 2015, 02:24:38
This looks.... niiiiice !
Post by: appleonama on Tue, 19 May 2015, 02:28:08
I recently bought a eagle with 62g clears and they're great. However while rebuilding the keyboard I tested some gateron blacks and they are soooo smooth. Would it be a sin if I used gaterons on this keyboard?
Post by: Frizer on Tue, 19 May 2015, 03:09:01
Guys what switches should I use on my orion
I recently bought a eagle with 62g clears and they're great. However while rebuilding the keyboard I tested some gateron blacks and they are soooo smooth. Would it be a sin if I used gaterons on this keyboard?
I think quite a few will get made with Gateron Blacks.
Post by: Want on Tue, 19 May 2015, 03:15:17
Guys what switches should I use on my orion
I recently bought a eagle with 62g clears and they're great. However while rebuilding the keyboard I tested some gateron blacks and they are soooo smooth. Would it be a sin if I used gaterons on this keyboard?
Gaterons will probably be just as popular as Cherry switches, at least on GH.
I'm under the impression that Duck keyboards are quite sturdy, unless you go for the plastic plate. You might want to keep that in mind, but really I wouldn't be able to say what to go for, that's your own opinion.
I've got some Gateron blacks, lube, stickers and springs ready for assembly :>
Post by: appleonama on Tue, 19 May 2015, 04:34:21
Guys what switches should I use on my orion
I recently bought a eagle with 62g clears and they're great. However while rebuilding the keyboard I tested some gateron blacks and they are soooo smooth. Would it be a sin if I used gaterons on this keyboard?
I think quite a few will get made with Gateron Blacks.
I got a steel plate.Guys what switches should I use on my orion
I recently bought a eagle with 62g clears and they're great. However while rebuilding the keyboard I tested some gateron blacks and they are soooo smooth. Would it be a sin if I used gaterons on this keyboard?
Gaterons will probably be just as popular as Cherry switches, at least on GH.
I'm under the impression that Duck keyboards are quite sturdy, unless you go for the plastic plate. You might want to keep that in mind, but really I wouldn't be able to say what to go for, that's your own opinion.
I've got some Gateron blacks, lube, stickers and springs ready for assembly :>
I've been using topre for a while now, using clears doesn't seem too comfortable anymore. The tactile bump is a little awkward for me now.
I think I'm going with Gateron black, they're just ultra smooth.What springs are you putting into those blacks? I have 62g springs from sprit. I was going to use them in some clear switches but I am unsure now.
Post by: Want on Tue, 19 May 2015, 04:52:37
I got a steel plate.
I've been using topre for a while now, using clears doesn't seem too comfortable anymore. The tactile bump is a little awkward for me now.
I think I'm going with Gateron black, they're just ultra smooth.What springs are you putting into those blacks? I have 62g springs from sprit. I was going to use them in some clear switches but I am unsure now.
It's between 65g, 68g and 72g. I do like switches with a bit of brawn to them :-)
Might have to wait to try them out on the actual board and PCB, to see how the weight actually feels in action.
Post by: appleonama on Tue, 19 May 2015, 05:13:17
Post by: FreeChemicals on Tue, 19 May 2015, 05:53:58
Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/a9595c926b75fd79b0b0d4a214a14674.JPG)
(http://i.imgur.com/2xNnI3a.png)
I just need stabs + stickers (trying plot my own with one of these http://imgur.com/7iHm0AY), and I'm good to go! ;D
Post by: wlhlm on Tue, 19 May 2015, 05:54:37
Post by: wlhlm on Wed, 20 May 2015, 07:09:35
(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)
(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)
(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
Post by: appleonama on Wed, 20 May 2015, 14:56:16
Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
I need more pictures of grey blue I hope I made the right decision
Post by: wlhlm on Wed, 20 May 2015, 14:58:12
I hope so as well. Duck says black and silver is his favourite combination.Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
I need more pictures of grey blue I hope I made the right decision
Post by: appleonama on Wed, 20 May 2015, 14:59:10
I hope so as well. Duck says black and silver is his favourite combination.Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
I need more pictures of grey blue I hope I made the right decision
Blue grey and silver looks good in the pictures
Post by: frostylove on Thu, 21 May 2015, 00:16:38
Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
Is the case shown grey-blue or black ?
Post by: whentheclouds on Thu, 21 May 2015, 00:22:58
Post by: appleonama on Thu, 21 May 2015, 02:35:08
black :pEnjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
Is the case shown grey-blue or black ?
Post by: admiralvorian on Thu, 21 May 2015, 11:56:13
Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
wait, does this mean that you've already received yours?
can't wait until my batch ships. I'm gonna do some nasty **** with this baby.
Post by: wlhlm on Thu, 21 May 2015, 11:58:15
No, unfortunately not. :(Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
wait, does this mean that you've already received yours?
can't wait until my batch ships. I'm gonna do some nasty **** with this baby.
These are pictures Duck posted to kbdlab. I thought I'd share them here to keep us entertained until the board ships.
Post by: admiralvorian on Thu, 21 May 2015, 12:10:52
No, unfortunately not. :(Enjoy: :thumb:Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8e982239f81b5edc4dd1fa422da8e147.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/8ee7e09f613f5fe0472282fa8eca19df.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/085/690/002/3e0e940a4c8333baa0afc3b1ac37bf69.JPG)
wait, does this mean that you've already received yours?
can't wait until my batch ships. I'm gonna do some nasty **** with this baby.
These are pictures Duck posted to kbdlab. I thought I'd share them here to keep us entertained until the board ships.
i thought i went crazy for a second there haha
Post by: orcinus on Fri, 22 May 2015, 11:21:36
i thought i went crazy for a second there haha
You did. We all did.
That's why we're here.
Post by: asgeirtj on Mon, 25 May 2015, 15:58:14
Would be amazing to hear a sound test comparing the different plates, preferably with o-rings on (the mission for the quietest board).
Post by: yuktsi on Mon, 25 May 2015, 20:26:13
Post by: whentheclouds on Mon, 25 May 2015, 20:43:10
Post by: FreeChemicals on Tue, 26 May 2015, 01:50:25
Elton just pmed me for address. Does it mean that the keyboards are shipping soon?
No, he was just going over shipping addresses, to make sure they are correct.
Post by: wlhlm on Tue, 26 May 2015, 02:36:51
Post by: wlhlm on Tue, 26 May 2015, 14:12:45
What will be the dimensions of the case? :rolleyes: I'm asking, because I'm looking to get a matching wrist rest.Weren't they the same dimensions as the V1?
Post by: appleonama on Wed, 27 May 2015, 22:20:44
Post by: Want on Sat, 30 May 2015, 11:25:01
any ETA ?I think a month ago Elton said two months, so another month to go.
Post by: wlhlm on Sun, 31 May 2015, 09:39:47
(http://cfile22.uf.tistory.com/image/22790C49556AEF1D2AB98C)
(http://cfile24.uf.tistory.com/image/2132754B556AEF2301A3BB)
(http://cfile30.uf.tistory.com/image/277C2E4B556AEF2C264100)
Post by: Want on Sun, 31 May 2015, 12:09:41
New pictures: http://duck0113.tistory.com/123Show Image(http://cfile22.uf.tistory.com/image/22790C49556AEF1D2AB98C)Show Image(http://cfile24.uf.tistory.com/image/2132754B556AEF2301A3BB)Show Image(http://cfile30.uf.tistory.com/image/277C2E4B556AEF2C264100)
Looking good. Wish the pictures were higher resolution though. I thought South Korea had superspeeds in the internets, so what's the point in making the pictures so small?
Post by: filphil on Sun, 31 May 2015, 12:19:36
Post by: admiralvorian on Mon, 01 June 2015, 09:11:20
any ETA ?I think a month ago Elton said two months, so another month to go.
did I read somewhere that that's for the first 30 or so, then the second batch would be produced? I'm no. 47 ;_;
Post by: MarkRobbo on Mon, 01 June 2015, 09:40:17
any ETA ?I think a month ago Elton said two months, so another month to go.
did I read somewhere that that's for the first 30 or so, then the second batch would be produced? I'm no. 47 ;_;
Another month for second batch IIRC, look earlier in the thread the answer will probably be there.
Im super excited to receive this already :D
Post by: appleonama on Mon, 01 June 2015, 18:13:49
exactly what came to my mindNew pictures: http://duck0113.tistory.com/123Show Image(http://cfile22.uf.tistory.com/image/22790C49556AEF1D2AB98C)Show Image(http://cfile24.uf.tistory.com/image/2132754B556AEF2301A3BB)Show Image(http://cfile30.uf.tistory.com/image/277C2E4B556AEF2C264100)
Looking good. Wish the pictures were higher resolution though. I thought South Korea had superspeeds in the internets, so what's the point in making the pictures so small?
also can we get some blue grey housing pictures? black is looking amazing... I hope blue grey will look this good
Post by: wlhlm on Mon, 08 June 2015, 03:05:40
[attachimg=1]
Post by: Jason_IRL on Tue, 09 June 2015, 23:29:29
Post by: Want on Wed, 10 June 2015, 08:35:00
Post by: FreeChemicals on Wed, 10 June 2015, 09:21:47
Are we still looking at an "end of June" delivery date?
As far as I know, it has always been the first week(s) of July.
Post by: ctrlX on Wed, 10 June 2015, 11:09:31
That's for the first batch, correct? Any ETA on the second batch?Are we still looking at an "end of June" delivery date?
As far as I know, it has always been the first week(s) of July.
Post by: fmendonca on Wed, 10 June 2015, 12:30:11
Post by: elton5354 on Wed, 10 June 2015, 18:05:27
That's for the first batch, correct? Any ETA on the second batch?Are we still looking at an "end of June" delivery date?
As far as I know, it has always been the first week(s) of July.
The production is delayed a bit due to their CNC machines having a bit of a problem..I'll update when I get more info.
Post by: wlhlm on Wed, 10 June 2015, 18:14:47
Can you link to the thread with status updates, or does Duck contact you directly?That's for the first batch, correct? Any ETA on the second batch?Are we still looking at an "end of June" delivery date?
As far as I know, it has always been the first week(s) of July.
The production is delayed a bit due to their CNC machines having a bit of a problem..I'll update when I get more info.
Post by: elton5354 on Wed, 10 June 2015, 18:23:45
Can you link to the thread with status updates, or does Duck contact you directly?That's for the first batch, correct? Any ETA on the second batch?Are we still looking at an "end of June" delivery date?
As far as I know, it has always been the first week(s) of July.
The production is delayed a bit due to their CNC machines having a bit of a problem..I'll update when I get more info.
I contact directly with Truecustom.
Post by: pr1me on Fri, 12 June 2015, 00:21:23
If anyone is interested, PM me.
Transfered.
Post by: filphil on Fri, 12 June 2015, 01:07:49
I have to let my order go :'(
If anyone is interested, PM me.Show Image(http://i.imgur.com/8ZDvGL5.jpg)
Just sent you a pm
Post by: ide_ on Fri, 12 June 2015, 09:47:15
please PM me
Thanks.
Post by: kurocat on Fri, 12 June 2015, 15:03:56
Post by: MarkRobbo on Fri, 12 June 2015, 15:12:56
Post by: wlhlm on Fri, 12 June 2015, 15:14:31
Post by: MarkRobbo on Fri, 12 June 2015, 15:16:14
Ain't no group buy without a delay... :rolleyes:
Ain't that the truth
Post by: cooldiscretion on Fri, 12 June 2015, 15:16:41
Ain't no group buy without a delay... :rolleyes:
Amen, brother.
Post by: admiralvorian on Fri, 12 June 2015, 15:23:35
Ain't no group buy without a delay... :rolleyes:
Amen, brother.
it will make receiving parts / building the board all the more special.
Post by: FrostyToast on Fri, 12 June 2015, 15:27:58
That's for the first batch, correct? Any ETA on the second batch?Are we still looking at an "end of June" delivery date?
As far as I know, it has always been the first week(s) of July.
The production is delayed a bit due to their CNC machines having a bit of a problem..I'll update when I get more info.
All I read was, "Everything is going as expected"
:))
Post by: filphil on Fri, 12 June 2015, 21:11:13
Post by: Evo_Spec on Fri, 12 June 2015, 21:39:01
Question - I picked up pr1me's order. It has an extra PCB purchased. How do you all recommend storing it as an emergency pcb if something were to go awry for myself or a future Orion owner? There's enough parts to basically make a second board but, unfortunately, there's no option right now to pick up a second top case. As it stands there's a spare with me for those that have an unfortunate incident. :thumb:
My guess (really not sure) for storage is an anti-static bag with a silica bag to control moisture but i think that's probably excessive as my NerD PCB was just wrapped in foam and a plastic bag.
Post by: filphil on Fri, 12 June 2015, 21:41:52
Question - I picked up pr1me's order. It has an extra PCB purchased. How do you all recommend storing it as an emergency pcb if something were to go awry for myself or a future Orion owner? There's enough parts to basically make a second board but, unfortunately, there's no option right now to pick up a second top case. As it stands there's a spare with me for those that have an unfortunate incident. :thumb:
My guess (really not sure) for storage is an anti-static bag with a silica bag to control moisture but i think that's probably excessive as my NerD PCB was just wrapped in foam and a plastic bag.
Excessive, sure. This keyboard screams excessive though!
Post by: Bromono on Sun, 14 June 2015, 11:44:04
Bromono - Silver Winkeyles - Acrylic Angled Bottom - Plastic - $362.69 C34 PAID
transferd
Post by: yuktsi on Thu, 18 June 2015, 03:35:16
Post by: orcinus on Thu, 18 June 2015, 17:21:11
Post by: rohanmital on Sun, 21 June 2015, 14:49:17
If anyone is interested in taking my slot. let me know!
Bromono - Silver Winkeyles - Acrylic Angled Bottom - Plastic - $362.69 C34 PAID
If you are able to switch to winkey I may be able to take it
Post by: whentheclouds on Sun, 21 June 2015, 15:08:43
Post by: coast9x72 on Thu, 25 June 2015, 13:11:32
If anyone is interested in taking my slot. let me know!
Bromono - Silver Winkeyles - Acrylic Angled Bottom - Plastic - $362.69 C34 PAID
hello, i sent a message to you. Please check your inbox. Thanks.
Anyone else want to transfer slots, please send me a message. Thank a lot!
Post by: Blackehart on Thu, 25 June 2015, 16:09:37
Post by: Want on Thu, 02 July 2015, 10:51:28
Post by: Fnzzy on Thu, 02 July 2015, 11:49:12
Post by: filphil on Thu, 02 July 2015, 15:34:40
Post by: Metr0 on Thu, 02 July 2015, 15:35:30
Post by: blighty on Thu, 02 July 2015, 17:47:06
Since this is my first aluminum keyboard group buy I wanted to ask this - If the alu casing gets dented in transit, are we SOL? Currently I'm 1 for 2 in cases that have been dented inbound to me. I'd be so sad if this one happened to be 2/3. :(
OP says you're covered, assuming you report the damage somewhat quickly.
- Deadline for order is April 20, 2015.
- Order ONLY if you can pay the invoice by the deadline (May 1st)
- There will be no extras for sale after this group buy is closed, so please put your order in before it's too late ;)
- I will send invoices through Paypal to everyone, so you need a verified Paypal account to receive and pay. Also please check the information carefully before submitting your order. There will be Paypal fees added to the price.
- If you want to make changes to your order, please send me a PM.
- I can only guarantee damages for 7 days from the day you receive the items.
Post by: filphil on Thu, 02 July 2015, 19:59:58
Since this is my first aluminum keyboard group buy I wanted to ask this - If the alu casing gets dented in transit, are we SOL? Currently I'm 1 for 2 in cases that have been dented inbound to me. I'd be so sad if this one happened to be 2/3. :(
OP says you're covered, assuming you report the damage somewhat quickly.- Deadline for order is April 20, 2015.
- Order ONLY if you can pay the invoice by the deadline (May 1st)
- There will be no extras for sale after this group buy is closed, so please put your order in before it's too late ;)
- I will send invoices through Paypal to everyone, so you need a verified Paypal account to receive and pay. Also please check the information carefully before submitting your order. There will be Paypal fees added to the price.
- If you want to make changes to your order, please send me a PM.
- I can only guarantee damages for 7 days from the day you receive the items.
Ah, I thought I read that from a different GB OP. Thanks!
Post by: yuktsi on Sun, 05 July 2015, 06:11:32
Post by: wlhlm on Sun, 05 July 2015, 06:12:40
ETA? it has been 2 months
Had email contact with Elton during GH downtime. It seems there's a delay til mid august.
Post by: admiralvorian on Mon, 06 July 2015, 19:11:31
ETA? it has been 2 monthsHad email contact with Elton during GH downtime. It seems there's a delay til mid august.
;_;
Post by: ramnes on Sat, 11 July 2015, 04:32:34
I'm going one month on holidays, it would really be a shame that it arrives when I'm not there.
Post by: elton5354 on Sat, 11 July 2015, 10:09:14
Can we please have an idea of when packages are going to be sent?
I'm going one month on holidays, it would really be a shame that it arrives when I'm not there.
I've been told it's been delayed until mid August. I can ask if they can delay your shipment until you're back..
Post by: ramnes on Sat, 11 July 2015, 10:15:57
Thanks Elton!
Post by: Fnzzy on Mon, 13 July 2015, 07:01:34
Post by: sethk_ on Mon, 13 July 2015, 07:52:17
(http://kbdlab.co.kr/files/attach/images/340/669/901/002/1abf51b34ac85f46ac3c777b8aa14917.jpg)
Post by: baldgye on Mon, 13 July 2015, 10:13:18
From kbdlabShow Image(http://kbdlab.co.kr/files/attach/images/340/669/901/002/1abf51b34ac85f46ac3c777b8aa14917.jpg)
god damnit I want this board
Post by: admiralvorian on Mon, 13 July 2015, 12:17:56
From kbdlabShow Image(http://kbdlab.co.kr/files/attach/images/340/669/901/002/1abf51b34ac85f46ac3c777b8aa14917.jpg)
god damnit I want this board
I'm finding it a bit unclear due to most of the pictures having rainbow backlighting, but we can program the RGB LEDs right? They don't just show rainbow colors all the time, do they?
Post by: sethk_ on Mon, 13 July 2015, 12:18:34
No I had an Octagon and they can changeFrom kbdlabShow Image(http://kbdlab.co.kr/files/attach/images/340/669/901/002/1abf51b34ac85f46ac3c777b8aa14917.jpg)
god damnit I want this board
I'm finding it a bit unclear due to most of the pictures having rainbow backlighting, but we can program the RGB LEDs right? They don't just show rainbow colors all the time, do they?
Post by: Blackhawk on Mon, 13 July 2015, 12:19:26
From kbdlabShow Image(http://kbdlab.co.kr/files/attach/images/340/669/901/002/1abf51b34ac85f46ac3c777b8aa14917.jpg)
That board is so damn nice
Post by: yicaoyimu on Mon, 13 July 2015, 12:24:09
Post by: radio_killah on Mon, 13 July 2015, 14:32:46
Post by: wlhlm on Mon, 13 July 2015, 15:11:37
Hmm. Hoping I can snag one of these in the classifieds.I hope your wallet is prepared :-X
Post by: radio_killah on Mon, 13 July 2015, 15:43:41
Hmm. Hoping I can snag one of these in the classifieds.I hope your wallet is prepared :-X
I already opened it for a 356cl. I think I can handle it :rolleyes:
Post by: filphil on Mon, 13 July 2015, 15:51:23
Hmm. Hoping I can snag one of these in the classifieds.I hope your wallet is prepared :-X
I already opened it for a 356cl. I think I can handle it :rolleyes:
(http://i.memecaptain.com/gend_images/ndROQg.jpg)
Post by: radio_killah on Mon, 13 July 2015, 17:14:21
Hmm. Hoping I can snag one of these in the classifieds.I hope your wallet is prepared :-X
I already opened it for a 356cl. I think I can handle it :rolleyes:Show Image(http://i.memecaptain.com/gend_images/ndROQg.jpg)
lol thanks filphil. For real though the Orion v2 looks awesome. So if anyone has a fully aluminum housing order they want to get rid of let me know!
Post by: appleonama on Tue, 14 July 2015, 04:54:41
https://www.youtube.com/watch?v=9o_Lw-9cleIFrom kbdlabShow Image(http://kbdlab.co.kr/files/attach/images/340/669/901/002/1abf51b34ac85f46ac3c777b8aa14917.jpg)
god damnit I want this board
I'm finding it a bit unclear due to most of the pictures having rainbow backlighting, but we can program the RGB LEDs right? They don't just show rainbow colors all the time, do they?
Post by: witbliz on Tue, 14 July 2015, 10:02:21
Post by: sethk_ on Tue, 14 July 2015, 15:18:39
(http://kbdlab.co.kr/files/attach/images/340/997/906/002/875d0be86cc6be6e776111ed6c1d19e1.jpg)
(http://kbdlab.co.kr/files/attach/images/340/997/906/002/4695a9bf16651d82ad2df3c63709bd99.jpg)
(http://kbdlab.co.kr/files/attach/images/340/997/906/002/15c031c8b40cd43b620445c20b83fbf9.jpg)
(http://kbdlab.co.kr/files/attach/images/340/997/906/002/d02c6036cbeda4400849f6c63677c21e.jpg)
Post by: wlhlm on Tue, 14 July 2015, 15:21:20
More photos of the Orion V2All those juicy pics. It's gonna be awesome when it finally arrives! :cool:
[...]
Thanks for keeping us updated Seth. :thumb:
Post by: Dreamre on Tue, 14 July 2015, 16:05:44
Post by: MarkRobbo on Tue, 14 July 2015, 18:09:10
Looking for an order to take over for my GF. Please PM me!
Good luck! Tons of demand and not much supply for the Orion V2
Post by: elton5354 on Tue, 14 July 2015, 18:14:48
Looking for an order to take over for my GF. Please PM me!
I have 2, not sure if I should give one to your gf though. ;)
That looks hot especially with those dirty caps :D
(http://kbdlab.co.kr/files/attach/images/340/997/906/002/d02c6036cbeda4400849f6c63677c21e.jpg)
Post by: Data on Tue, 14 July 2015, 18:30:24
Post by: Fnzzy on Tue, 14 July 2015, 20:21:40
Post by: radio_killah on Tue, 14 July 2015, 21:52:42
Looks amazing! Needs more winkeyless though...
Yes. Anyone with WKL want to sell me their spot :cool:
Post by: admiralvorian on Thu, 16 July 2015, 17:40:07
Silver Winkey
Silver Aluminum Bottom
Steel Plate
please PM me if you want to take over my order, thanks
Edit: order has been taken
Post by: filphil on Thu, 16 July 2015, 17:51:12
have to let my order go :{
Silver Winkey
Silver Aluminum Bottom
Steel Plate
please PM me if you want to take over my order, thanks
(http://cdn.meme.am/instances2/500x/785899.jpg)
Post by: rsadek on Thu, 16 July 2015, 20:04:27
have to let my order go :{I have an idea. I'll take yours, and Radio_Killah can take my WKL.
Silver Winkey
Silver Aluminum Bottom
Steel Plate
please PM me if you want to take over my order, thanks
Post by: radio_killah on Thu, 16 July 2015, 20:17:17
have to let my order go :{I have an idea. I'll take yours, and Radio_Killah can take my WKL.
Silver Winkey
Silver Aluminum Bottom
Steel Plate
please PM me if you want to take over my order, thanks
What color combo you got Rsadek?
Post by: filphil on Thu, 16 July 2015, 20:19:09
What color combo you got Rsadek?
He has a silver WKL with acrylic bottom according to the order forms.
Post by: Dreamre on Thu, 16 July 2015, 21:19:48
Post by: wangbwhz on Sat, 18 July 2015, 09:48:10
Post by: wlhlm on Wed, 22 July 2015, 16:28:40
Firmware/Mapping for the Orion V2
O2D Orion V2 custom key mapper:
(http://kbdlab.co.kr/files/attach/images/19389/859/925/002/1947fd2c52984a70e09cb83a6fd8736a.JPG)
New features (based on Google translation):
- ISO key layout
- More layers (4+3Fn)
- RGB lighting support
- Added Media keys
- Added Mouse keys
- Added locking keys
Firmware is currently in testing stage.
Post by: wlhlm on Wed, 22 July 2015, 16:31:28
(http://kbdlab.co.kr/files/attach/images/340/274/906/002/c053255fc0bc3ec8e346839bb7d797f9.jpg)
(http://kbdlab.co.kr/files/attach/images/340/998/916/002/8b88f2205292766b71d7813801c4229d.JPG)
(http://kbdlab.co.kr/files/attach/images/340/998/916/002/1686ea34ca09c8fff07a19e10ef6d5e3.JPG)
Post by: filphil on Wed, 22 July 2015, 16:48:27
- RGB lighting support
Firmware is currently in testing stage.
As per google translate
Quote
3. Support RGB Function
- RGB color controls available in separate into the lower
So does that mean RGB in-switch lighting adjustment?!
Edit:
Probably not but here's the screen shots for the bottom RGB adjustment
Adjustment for acrylic bottom flat/angled
(http://kbdlab.co.kr/files/attach/images/19389/567/926/002/de42e4bf9fb0b5d8a7590676d4cb5815.jpg)
Adjustment for the aluminum portion
(http://kbdlab.co.kr/files/attach/images/19389/573/926/002/6131680209fa0d83e1bd7b4b82a61049.jpg)
Post by: wlhlm on Wed, 22 July 2015, 16:51:02
I think just for the RGB LEDs on the back
- RGB lighting support
Firmware is currently in testing stage.
As per google translateQuote3. Support RGB Function
- RGB color controls available in separate into the lower
So does that mean RGB in-switch lighting adjustment?!
(http://kbdlab.co.kr/files/attach/images/19389/859/925/002/571edbe355bf85d4c4ddec8fc626ec4e.JPG)
Post by: Jason_IRL on Wed, 22 July 2015, 17:18:13
Post by: Want on Wed, 22 July 2015, 17:31:57
Post by: Pemdas on Wed, 22 July 2015, 18:04:12
Post by: PunksDead on Wed, 22 July 2015, 18:14:18
So it'll sit in my drawer each day trying to muster up the courage to not mess up a $500 keyboard
Post by: Sed8op8 on Wed, 22 July 2015, 19:35:32
I guess I need more practice because I really don't feel like defiling a beautiful PCB or having to order extras in my next GB :))
See sed8s name on one of those open GB spreadsheets where you can see everyone's order.
1 aluminum upper casing
1 poly carbonate bottom casing
1 aluminum plate
6 PCBs
:)) yupp that's me
Edit: I'm also slightly OCD when it comes to my gear. So knowing there is a flaw somewhere even if its not a major device altering one drives me freaking bananas !!
Post by: Evo_Spec on Wed, 22 July 2015, 19:39:07
Post by: filphil on Wed, 22 July 2015, 19:41:22
Too bad i'm so far, i'd totally build your guy's boards.....
I plan on taking a trip to Japan next year. Maybe I'll have an extra PCB for you to solder for me!
Post by: Evo_Spec on Wed, 22 July 2015, 20:21:47
I'll have my soldering equipment ready lolToo bad i'm so far, i'd totally build your guy's boards.....
I plan on taking a trip to Japan next year. Maybe I'll have an extra PCB for you to solder for me!
Post by: Fnzzy on Thu, 23 July 2015, 10:54:47
Post by: wlhlm on Thu, 23 July 2015, 11:15:40
So far I have only seen rainbow backlighting, glad to see you can also display a solid color. Can't wait now!The Koreans love their rainbow. :p
Post by: Ngt on Thu, 23 July 2015, 17:50:32
Post by: orcinus on Fri, 24 July 2015, 08:00:56
So does that mean RGB in-switch lighting adjustment?!
Switch footprints on the PCB only accommodate one LED (two leads).
There's simply not enough pads for an RGB LED in each switch (not to mention routing that would be hellish).
Post by: sethk_ on Fri, 24 July 2015, 14:50:08
well, 2 prong RGB LEDs might work, depends on how the Orion V2 is, but on my Octagon 2 prong RGB didn't work, but on my Leeku they did. Obviously you can't control the RGB on them though, they just cycle throughSo does that mean RGB in-switch lighting adjustment?!
Switch footprints on the PCB only accommodate one LED (two leads).
There's simply not enough pads for an RGB LED in each switch (not to mention routing that would be hellish).
Post by: coast9x72 on Fri, 24 July 2015, 22:23:55
have to let my order go :{
Silver Winkey
Silver Aluminum Bottom
Steel Plate
please PM me if you want to take over my order, thanks
Edit: order has been taken
pmed for a long time but no reply and now i read this end line :-<
anyone else want to let your order go, please pm me. thanks
Post by: filphil on Mon, 27 July 2015, 16:22:37
I'm currently looking for someone who ordered a steel plate and would be willing to swap me for a plastic plate(I have an extra set). I'm trying to do a review/comparison of each of the plate types(with 62g gold ergo clears) offered in this group buy and the steel plate is the missing piece of the puzzle.
Elton has already tried helping me out buy, understandably, it's a tad late to add on a steel plate to the order.
Please PM me even if you're so much as on the fence about it. Thanks!
Post by: missalaire on Mon, 27 July 2015, 20:33:15
Can we please have an idea of when packages are going to be sent?
I'm going one month on holidays, it would really be a shame that it arrives when I'm not there.
I've been told it's been delayed until mid August. I can ask if they can delay your shipment until you're back..
Still looking like mid August?
Post by: Lastpilot on Fri, 31 July 2015, 14:46:42
Post by: yicaoyimu on Fri, 31 July 2015, 16:01:57
Please let this still be on schedule for mid august. Please please please :]
+1. I can't stand my rubber dome no more! Gimme dat mechanical sh1t please!
Post by: digi on Fri, 31 July 2015, 16:04:57
Post by: Sed8op8 on Fri, 31 July 2015, 16:09:08
damn it, Orion V2 looks so good..It really does Digi ! Im quite bummed I didn't go through with this one but can't get them all !!!
Post by: blighty on Fri, 31 July 2015, 16:27:20
Some of you received a PM from me already but I'll put this out there for anyone who might be willing to help -
I'm currently looking for someone who ordered a steel plate and would be willing to swap me for a plastic plate(I have an extra set). I'm trying to do a review/comparison of each of the plate types(with 62g gold ergo clears) offered in this group buy and the steel plate is the missing piece of the puzzle.
Elton has already tried helping me out buy, understandably, it's a tad late to add on a steel plate to the order.
Please PM me even if you're so much as on the fence about it. Thanks!
Wouldn't your best bet be to buy out a third person's order, one with a steel plate? Your pockets seem deep enough.
:))
Post by: FreeChemicals on Fri, 31 July 2015, 16:29:58
Post by: filphil on Fri, 31 July 2015, 18:13:57
Some of you received a PM from me already but I'll put this out there for anyone who might be willing to help -
I'm currently looking for someone who ordered a steel plate and would be willing to swap me for a plastic plate(I have an extra set). I'm trying to do a review/comparison of each of the plate types(with 62g gold ergo clears) offered in this group buy and the steel plate is the missing piece of the puzzle.
Elton has already tried helping me out buy, understandably, it's a tad late to add on a steel plate to the order.
Please PM me even if you're so much as on the fence about it. Thanks!
Wouldn't your best bet be to buy out a third person's order, one with a steel plate? Your pockets seem deep enough.
:))
You set this one up, didn't you?!
I'm parting with my order, #5 on the list. Please send me a PM if you have any interest.
Post by: coast9x72 on Fri, 31 July 2015, 23:11:01
I'm parting with my order, #5 on the list. Please send me a PM if you have any interest.Pending.
d4mn i be late once again :-<
Post by: blighty on Sat, 01 August 2015, 00:39:03
Some of you received a PM from me already but I'll put this out there for anyone who might be willing to help -
I'm currently looking for someone who ordered a steel plate and would be willing to swap me for a plastic plate(I have an extra set). I'm trying to do a review/comparison of each of the plate types(with 62g gold ergo clears) offered in this group buy and the steel plate is the missing piece of the puzzle.
Elton has already tried helping me out buy, understandably, it's a tad late to add on a steel plate to the order.
Please PM me even if you're so much as on the fence about it. Thanks!
Wouldn't your best bet be to buy out a third person's order, one with a steel plate? Your pockets seem deep enough.
:))
You set this one up, didn't you?!I'm parting with my order, #5 on the list. Please send me a PM if you have any interest.
LOL. I didn't have to set it up. The longer a groupbuy takes, the more people realize what they can do with the cash they put up in it. Congrats on your 3rd OrionV2. I'd say to complete your set, you still need a red top (order #28, 50 or 60). :))
Post by: rainb1ood on Sun, 02 August 2015, 20:28:10
Post by: elton5354 on Sun, 02 August 2015, 21:34:32
Will there be a re-confirmation of shipping address before this ships? I'm just curious and you could say a bit paranoid since I changed my address lol
Yes, definitely. I'll post here to let you know they are almost ready to ship and to let me know if you want to confirm your address with me.
Actually, you can let me know now. Doesn't matter.
Edit: just send me a PM with your current address and if it's different from what I have, I'll let you know.
Post by: coast9x72 on Sun, 02 August 2015, 23:48:47
Post by: jaemzp on Mon, 03 August 2015, 22:00:21
Post by: coast9x72 on Tue, 04 August 2015, 00:23:13
Post by: appleonama on Tue, 04 August 2015, 07:14:40
Post by: duzeyao on Sat, 08 August 2015, 20:20:15
Post by: appleonama on Sun, 09 August 2015, 02:12:18
GG NO RE KEYBOARDS TILL DECEMBER
Post by: Fnzzy on Sun, 09 August 2015, 07:54:16
Post by: Fnzzy on Fri, 14 August 2015, 06:47:15
Post by: wlhlm on Fri, 14 August 2015, 07:35:20
(http://puu.sh/jh6Mu/3ac26033a2.png)
And I thought, I already had all the parts together...
Looks like my build is getting delayed even further... :'(
Elton, no pressure from my side ;)
Post by: Ahkrael on Fri, 14 August 2015, 08:42:27
Post by: Halverson on Fri, 14 August 2015, 13:31:41
Direct message from the maker:
"Thank you for the inform. I am sorry but schedule will be changed due to surface treatment takes too much time than i expected. I will let you know revise schedule this weekend. I am So Sorry again."
Post by: Lastpilot on Fri, 14 August 2015, 13:35:25
Post by: Fnzzy on Fri, 14 August 2015, 14:45:28
Post by: R1N3 on Fri, 14 August 2015, 15:00:48
Bad news. Production delay :(
Direct message from the maker:
"Thank you for the inform. I am sorry but schedule will be changed due to surface treatment takes too much time than i expected. I will let you know revise schedule this weekend. I am So Sorry again."
I wish this production delay meant that I could put a delayed order in :C
Post by: appleonama on Sat, 15 August 2015, 17:34:50
Post by: Pemdas on Sun, 16 August 2015, 04:19:31
Bad news. Production delay :(
Direct message from the maker:
"Thank you for the inform. I am sorry but schedule will be changed due to surface treatment takes too much time than i expected. I will let you know revise schedule this weekend. I am So Sorry again."
A little sad that there's been another delay, but the anticipation will just make it all that much sweeter when I get it in my hands ;)
Thanks for the update
Post by: Arvid on Tue, 18 August 2015, 04:42:44
I might let go of my set since I had planned to use the GMK triumph set, but it looks like utter garbage. Also, I am more of a Topre person that cherry. If anyone is interested let me know I will take offers.PMd!
Post by: duzeyao on Tue, 18 August 2015, 05:20:16
Post by: Rainbow_ on Tue, 18 August 2015, 15:27:36
Delay till when? :-\ :-\
Until it's not delayed!
Post by: ramnes on Tue, 18 August 2015, 16:47:00
(sorry about the repost, but I'm crying in front of that video)
Post by: R1N3 on Tue, 18 August 2015, 16:51:04
To make the wait a bit harder:
(sorry for repost, but I'm crying in front of that video)
I REALLY should have pulled the trigger on this..
Post by: rsadek on Tue, 18 August 2015, 22:04:21
Post by: filphil on Tue, 18 August 2015, 22:18:49
Edit
Acrylic angled?
Post by: rsadek on Wed, 19 August 2015, 00:19:34
I got you my friend. Just remind me when everything gets shipped out.Cool buddy :) yeah acrylic angled is what I'm after!
Edit
Acrylic angled?
Post by: R1N3 on Thu, 20 August 2015, 09:13:43
Post by: animated on Fri, 21 August 2015, 17:17:12
Post by: 64rky on Sat, 22 August 2015, 11:43:13
If I can get rid of my windows 98 cherry set from the Ivan GB, I think I'm willing to let go of my Orion order. So once that keyset sells I'll let you guys know :) Or if someone wanted to buy both feel free to PM me.
Windows 98 Cherry
Orion, Winkeyless, Blue, Steel Plate, Flat Clear Acrylic Bottom
I would be more than happy to take over your order if you decide not to go ahead.
Post by: ph3nomzlol on Mon, 24 August 2015, 01:00:32
I am order #23 in the first round:
-Silver Winkeyless Top
-Plastic Plate
-Flat Acrylic Bottom w/ Chrome Feet
PM me if interested in taking over my order!
SOLD to R1N3 :thumb:
Post by: Fnzzy on Mon, 24 August 2015, 04:58:09
Post by: 64rky on Mon, 24 August 2015, 19:46:37
Hello all! Well, after the delays and a long debate with myself about keyboards, I think I am going to be letting my order go.
I am order #23 in the first round:
-Silver Winkeyless Top
-Plastic Plate
-Flat Acrylic Bottom w/ Chrome Feet
PM me if interested in taking over my order!
Pending to R1N3 :thumb:
Darnit! I miss everything...
Post by: ph3nomzlol on Mon, 24 August 2015, 21:13:04
Hello all! Well, after the delays and a long debate with myself about keyboards, I think I am going to be letting my order go.
I am order #23 in the first round:
-Silver Winkeyless Top
-Plastic Plate
-Flat Acrylic Bottom w/ Chrome Feet
PM me if interested in taking over my order!
Pending to R1N3 :thumb:
Darnit! I miss everything...
You aren't the one pending for animated's order? I thought you might have snagged that one :-\
Post by: 64rky on Tue, 25 August 2015, 05:43:40
Hello all! Well, after the delays and a long debate with myself about keyboards, I think I am going to be letting my order go.
I am order #23 in the first round:
-Silver Winkeyless Top
-Plastic Plate
-Flat Acrylic Bottom w/ Chrome Feet
PM me if interested in taking over my order!
Pending to R1N3 :thumb:
Darnit! I miss everything...
You aren't the one pending for animated's order? I thought you might have snagged that one :-\
Sent a PM, but haven't heard anything. I hope so.
Post by: appleonama on Tue, 25 August 2015, 06:07:26
appleonama Blue Grey Winkey Silver Aluminum Bottom Steel 1 x acrylic angled bottom
1x flat acrylic bottom with chrome feet United States 3.864 $455.00 $67.65 $522.65 $20.68 $543.33 C49 PAID
Post by: 64rky on Tue, 25 August 2015, 06:43:32
Hello, I am letting go of my order please pm me if you are interested. It is currently pending but whoever pays immediately I will let it go to you.
appleonama Blue Grey Winkey Silver Aluminum Bottom Steel 1 x acrylic angled bottom
1x flat acrylic bottom with chrome feet United States 3.864 $455.00 $67.65 $522.65 $20.68 $543.33 C49 PAID
PM sent
Post by: animated on Tue, 25 August 2015, 12:00:03
Hello all! Well, after the delays and a long debate with myself about keyboards, I think I am going to be letting my order go.
I am order #23 in the first round:
-Silver Winkeyless Top
-Plastic Plate
-Flat Acrylic Bottom w/ Chrome Feet
PM me if interested in taking over my order!
Pending to R1N3 :thumb:
Darnit! I miss everything...
You aren't the one pending for animated's order? I thought you might have snagged that one :-\
Sent a PM, but haven't heard anything. I hope so.
Hello all! Well, after the delays and a long debate with myself about keyboards, I think I am going to be letting my order go.
I am order #23 in the first round:
-Silver Winkeyless Top
-Plastic Plate
-Flat Acrylic Bottom w/ Chrome Feet
PM me if interested in taking over my order!
Pending to R1N3 :thumb:
Darnit! I miss everything...
You aren't the one pending for animated's order? I thought you might have snagged that one :-\
Sent a PM, but haven't heard anything. I hope so.
Sorry for the delayed responses! I'm currently working something it out with someone, but I'll let you guys know if it falls through!
Post by: Rainbow_ on Tue, 25 August 2015, 20:41:55
u have been joked by the jokester!!!
Post by: ph3nomzlol on Wed, 26 August 2015, 08:51:34
Hey guys I am NOT looking to let go of my order!
u have been joked by the jokester!!!
Oh, you ^-^
Post by: animated on Wed, 26 August 2015, 14:51:44
I am looking for a straight trade. My winkeyless blue top for a silver one, winkeyless or not :thumb:
Post by: appleonama on Wed, 26 August 2015, 16:08:55
Post by: jaemzp on Wed, 26 August 2015, 20:41:01
My order is still available if anyone wants it
If you ever decide to split the order, I'd gladly grab that angled acrylic bottom off of you.
Post by: 64rky on Wed, 26 August 2015, 21:01:21
My order is still available if anyone wants it
If you ever decide to split the order, I'd gladly grab that angled acrylic bottom off of you.
I'd take the rest.
Post by: elton5354 on Wed, 26 August 2015, 21:42:56
Post by: Pemdas on Wed, 26 August 2015, 22:11:58
Sorry guys, I don't have any definite date as to when shipping will occur. As always, I will update ASAP once I know any new information.
Darn was hoping to get a more solid schedule after the weekend.
Either way thanks for keeping us in the loop :thumb: :thumb:
Post by: Fnzzy on Thu, 27 August 2015, 06:14:45
Post by: Permeability on Tue, 01 September 2015, 19:40:10
29 Permeability Silver Winkey Acrylic Angled Bottom Steel United States 2.02 $296.00 $56.53 $352.53 $14.05 $366.57 C29 PAID
PM me, thanks!!
gone!
Post by: ekw808 on Thu, 03 September 2015, 11:13:15
Post by: ika on Thu, 03 September 2015, 14:59:56
Post by: appleonama on Thu, 03 September 2015, 19:26:22
Post by: malcomkern on Fri, 04 September 2015, 12:16:15
Post by: E3E on Sat, 05 September 2015, 20:05:12
Still love MX tactile and linear, but g'damn. Alps is dreamy in all its variants. I won't ever leave behind MX boards and all the fun modding possibilities there, but I would LOVE to have a backlit Alps TKL like this with some SKCL greens. :thumb:
Oh well; I can dream!
Post by: Jason_IRL on Tue, 08 September 2015, 22:53:41
PM only if you are serious. Thank you
EDIT: Sold.
Post by: 64rky on Wed, 09 September 2015, 06:17:34
Selling Order. #20
PM only if you are serious. Thank you
What does your order consist of?
Post by: ika on Wed, 09 September 2015, 08:09:34
Selling Order. #20
PM only if you are serious. Thank you
What does your order consist of?
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
Post by: Rainbow_ on Thu, 10 September 2015, 23:10:34
Post by: yuktsi on Sun, 13 September 2015, 21:04:36
You guys think it will be done by the end of the year?I hope so. hmmmmm
Post by: animated on Mon, 14 September 2015, 11:45:56
Looking for someone to take over my order again.
Blue grey winkeyless, steel plate, flat acrylic bottom :)
edit: sold to sncbraxsc2
Post by: ramnes on Mon, 14 September 2015, 18:57:46
:confused:
Post by: PrinsPils on Mon, 14 September 2015, 19:54:06
Post by: frostylove on Tue, 15 September 2015, 15:03:26
Anyone who want to take over my order please PM me.
ITEM SOLD.
Feeling bored in keyboards now. :blank:
Post by: rsadek on Tue, 15 September 2015, 20:24:20
http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50 (http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50)
???
duuuuuuude! How can I get an ALPS plate? Someone tell me, please!
-R
Post by: Rainbow_ on Tue, 15 September 2015, 21:14:18
http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50 (http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50)
???
duuuuuuude! How can I get an ALPS plate? Someone tell me, please!
-R
It was available when you submitted your order
Post by: Sed8op8 on Tue, 15 September 2015, 21:20:08
Post by: SeeThruHead on Wed, 16 September 2015, 11:43:41
Post by: Rainbow_ on Wed, 16 September 2015, 12:01:46
have these shipped out yet?
Nope
Post by: r0mIe_Ng on Wed, 16 September 2015, 17:25:12
Post by: rsadek on Thu, 17 September 2015, 02:24:54
Well, sort of. I picked up an order that someone let go since I missed the original order period. So I'm really asking will someone please sell me an ALPS plate? :)http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50 (http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50)
???
duuuuuuude! How can I get an ALPS plate? Someone tell me, please!
-R
It was available when you submitted your order
Post by: ramnes on Thu, 17 September 2015, 02:59:42
Post by: filphil on Sat, 19 September 2015, 21:17:37
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/cd8abc547e5adf6e11b7b1a89faa1346.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/97f19202926f1bbe8a59488d8d1b3350.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/4a204a5b4f372dafca873aa74b7f49e2.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/c7652a1d86a54dfea2b614cadaf86ec5.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/e4e0f4c5d7bbfceeef6532f6d3d8eb4b.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/b6aed43a4df1a661e0aa23a99cba8381.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/d818d25435165eac8a0d37a9565c1c29.jpg)
(http://kbdlab.co.kr/files/attach/images/340/659/079/003/37bdab992ec6db14214c97e023616a8d.jpg)
Post by: raymogi on Sat, 19 September 2015, 21:22:53
Post by: Sed8op8 on Sat, 19 September 2015, 21:38:38
Post by: E3E on Sat, 19 September 2015, 23:55:30
Post by: yuktsi on Sun, 20 September 2015, 00:25:29
Post by: Rainbow_ on Sun, 20 September 2015, 00:34:36
seems like someone has received their orion v2
holy mother of god
Post by: filphil on Sun, 20 September 2015, 01:11:31
seems like someone has received their orion v2
The pics I posted were from kbdlab. I think duck posted those.
Post by: Rainbow_ on Sun, 20 September 2015, 01:45:44
seems like someone has received their orion v2
The pics I posted were from kbdlab. I think duck posted those.
I dunno, the post title (according to google) is "2 Orion received" (Orion 2 received?) as well as the title of the page itself being "receipt of Orion 2"
Post by: ika on Sun, 20 September 2015, 01:59:41
Post by: filphil on Sun, 20 September 2015, 02:02:35
seems like someone has received their orion v2
The pics I posted were from kbdlab. I think duck posted those.
I dunno, the post title (according to google) is "2 Orion received" (Orion 2 received?) as well as the title of the page itself being "receipt of Orion 2"
Ah. So we ARE moving closer, :)
For anyone who has transferred their order, has elton followed up with you yet? We sent him a PM a couple weeks ago with no response, and no update to the googledoc. Just want to be sure everything is in order before things get shipped out.
I've messaged him before without issue.
Post by: ika on Sun, 20 September 2015, 02:05:30
For anyone who has transferred their order, has elton followed up with you yet? We sent him a PM a couple weeks ago with no response, and no update to the googledoc. Just want to be sure everything is in order before things get shipped out.I've messaged him before without issue.
Any idea how active he usually is? The PM was sent on the 9th, and he has only briefly logged in once since that time. I don't want to spam him with PMs since I'm sure he's busy, but with all the stuff going on with the TX1800 I'm a little wary about korean boards at the moment.
Post by: filphil on Sun, 20 September 2015, 02:18:24
For anyone who has transferred their order, has elton followed up with you yet? We sent him a PM a couple weeks ago with no response, and no update to the googledoc. Just want to be sure everything is in order before things get shipped out.I've messaged him before without issue.
Any idea how active he usually is? The PM was sent on the 9th, and he has only briefly logged in once since that time. I don't want to spam him with PMs since I'm sure he's busy, but with all the stuff going on with the TX1800 I'm a little wary about korean boards at the moment.
The last time I've messaged him and he replied was aug 26th. Elton's organized many of duck's group buys here on GH so I imagine our money is safe.
Post by: Fnzzy on Sun, 20 September 2015, 09:30:50
Post by: digi on Sun, 20 September 2015, 09:42:05
At the beginning it was said that we would receive a green PCB, in the pictures above there is a red PCB. Which colour do we get now :o
Duck PCB's have always been red
Post by: CyriusG on Sun, 20 September 2015, 12:38:03
Post by: Fnzzy on Sun, 20 September 2015, 12:54:24
At the beginning it was said that we would receive a green PCB, in the pictures above there is a red PCB. Which colour do we get now :o
Duck PCB's have always been red
Didn't the Octagon come with a green PCB?
(https://geekhack.org/index.php?action=dlattach;topic=65036.0;attach=97019;image)
Post by: Rainbow_ on Sun, 20 September 2015, 12:54:57
(http://i.imgur.com/HmmrrzC.png)
Post by: Fnzzy on Sun, 20 September 2015, 12:56:16
Post by: digi on Sun, 20 September 2015, 13:02:59
At the beginning it was said that we would receive a green PCB, in the pictures above there is a red PCB. Which colour do we get now :o
Duck PCB's have always been red
Didn't the Octagon come with a green PCB?Show Image(https://geekhack.org/index.php?action=dlattach;topic=65036.0;attach=97019;image)
oh ok, didn't know that, kewl
Post by: Pemdas on Sun, 20 September 2015, 17:10:23
I just looked on KBDlab again.Show Image(http://i.imgur.com/HmmrrzC.png)
Ohhhh snap. It's happening!!
Post by: Sed8op8 on Sun, 20 September 2015, 17:20:30
Post by: Rainbow_ on Sun, 20 September 2015, 18:00:06
I just looked on KBDlab again.Show Image(http://i.imgur.com/HmmrrzC.png)
Ohhhh snap. It's happening!!
It sure appears that way. Unfortunately, I can't actually read the thread. I even tried registering, but it hasn't sent me an email, and refuses to let me log in.
Post by: Fnzzy on Sun, 20 September 2015, 19:37:02
Quote
Finally, the preparation of ships ORION V2 is finished, try to start shipping this week.
Posted by True Custom on the 15th this month.
http://kbdlab.co.kr/index.php?mid=board_cUlO13&document_srl=3069971
Post by: Pemdas on Sun, 20 September 2015, 19:58:58
All I could find was this on the Free BoardQuoteFinally, the preparation of ships ORION V2 is finished, try to start shipping this week.
Posted by True Custom on the 15th this month.
http://kbdlab.co.kr/index.php?mid=board_cUlO13&document_srl=3069971
(http://i.imgur.com/xihg38M.gif)
Post by: digi on Sun, 20 September 2015, 20:19:29
Post by: Pemdas on Sun, 20 September 2015, 20:29:31
you girls should wait for an update from the supreme gb leader before you get your panties all worked up. haha
There are no brakes on this hype train :p
Post by: Rainbow_ on Sun, 20 September 2015, 20:31:46
you girls should wait for an update from the supreme gb leader before you get your panties all worked up. haha
There are no brakes on this hype train :p
CHOO CHOO
Post by: rainb1ood on Sun, 20 September 2015, 20:49:55
All I could find was this on the Free BoardQuoteFinally, the preparation of ships ORION V2 is finished, try to start shipping this week.
Posted by True Custom on the 15th this month.
http://kbdlab.co.kr/index.php?mid=board_cUlO13&document_srl=3069971
On that link, it says I have no permission to view the URL that was posted
> http://kbdlab.co.kr/index.php?mid=board_gb_do&document_srl=2611324
Does anyone have access?
Post by: kacase on Mon, 21 September 2015, 11:32:40
(http://i.imgur.com/rRsD9bI.png)
(http://imgur.com/swwuVlp.png)
Post by: kacase on Mon, 21 September 2015, 11:35:26
Post by: Rainbow_ on Mon, 21 September 2015, 14:16:37
According to the Forum Post, the shipping will be FINISHED BEFORE THANKSGIVING
thank sweet baby jesus
Post by: ryptide11 on Mon, 21 September 2015, 16:27:21
Post by: ika on Mon, 21 September 2015, 17:11:38
According to the Forum Post, the shipping will be FINISHED BEFORE THANKSGIVING
This is shipping from the original Korean buy, correct? So tack on another couple of weeks for sorting and shipping here and that pushes the date right up against Christmas shipping, so... expect these early next year?
Post by: kacase on Tue, 22 September 2015, 05:23:06
According to the Forum Post, the shipping will be FINISHED BEFORE THANKSGIVING
This is shipping from the original Korean buy, correct? So tack on another couple of weeks for sorting and shipping here and that pushes the date right up against Christmas shipping, so... expect these early next year?
if i am not completely mistaken the parts will be shipped directly to us; thats why the pricing for the shipping came from the korean postal service.
Post by: jaemzp on Tue, 22 September 2015, 06:44:28
According to the Forum Post, the shipping will be FINISHED BEFORE THANKSGIVING
aka Now-Thanksgiving
Hopefully everything arrives in perfect condition!
Post by: PunksDead on Tue, 22 September 2015, 18:04:57
Hit me up if interested
*prefer conus incase of address switch issues I can mail it
Got a new kitty want to spoil him
Post by: filphil on Tue, 22 September 2015, 18:23:16
More
(http://kbdlab.co.kr/[spoiler]files/attach/images/340/273/086/003/60fbd05822a0706a6eaa6a924afcfb7b.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/b8c43251402b8869b61e631a22fed0c5.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/3fd0b43d8920dde551490aa4eb57e835.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/0fcbbd06370f32d7d6c8987222260a96.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/07c194c7522f8019f6e3364f96056d78.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/12a77f6ca3b10d2a02308eb20cddb1c4.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/8fc00b5ead4c71b44484ab55c77220ba.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/4b39d77402b42c716156ce4a4d9e92e8.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/b8c43251402b8869b61e631a22fed0c5.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/3fd0b43d8920dde551490aa4eb57e835.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/0fcbbd06370f32d7d6c8987222260a96.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/07c194c7522f8019f6e3364f96056d78.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/12a77f6ca3b10d2a02308eb20cddb1c4.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/8fc00b5ead4c71b44484ab55c77220ba.JPG)
(http://kbdlab.co.kr/files/attach/images/340/273/086/003/4b39d77402b42c716156ce4a4d9e92e8.JPG)
Post by: Evo_Spec on Tue, 22 September 2015, 20:00:11
Post by: radio_killah on Wed, 23 September 2015, 11:36:24
Some ALPhaS goodness for yallMoreShow Image(http://kbdlab.co.kr/[spoiler]files/attach/images/340/273/086/003/60fbd05822a0706a6eaa6a924afcfb7b.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/b8c43251402b8869b61e631a22fed0c5.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/3fd0b43d8920dde551490aa4eb57e835.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/0fcbbd06370f32d7d6c8987222260a96.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/07c194c7522f8019f6e3364f96056d78.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/12a77f6ca3b10d2a02308eb20cddb1c4.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/8fc00b5ead4c71b44484ab55c77220ba.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/4b39d77402b42c716156ce4a4d9e92e8.JPG)
Nice job posting Leeku's pictures without even giving him credit.
Post by: Rainbow_ on Wed, 23 September 2015, 12:56:26
All I could find was this on the Free BoardQuoteFinally, the preparation of ships ORION V2 is finished, try to start shipping this week.
Posted by True Custom on the 15th this month.
http://kbdlab.co.kr/index.php?mid=board_cUlO13&document_srl=3069971
On that link, it says I have no permission to view the URL that was posted
> http://kbdlab.co.kr/index.php?mid=board_gb_do&document_srl=2611324
Does anyone have access?
My account just got authorized. It just says what has been already said; it will be done by Thanksgiving.
Also, they are running extra plates to be completed after the actual GB. http://kbd4u.com/product/detail.html?product_no=57&cate_no=1&display_group=2
Post by: rsadek on Thu, 24 September 2015, 04:45:02
Some ALPhaS goodness for yallMoreShow Image(http://kbdlab.co.kr/[spoiler]files/attach/images/340/273/086/003/60fbd05822a0706a6eaa6a924afcfb7b.JPG[/spoiler])Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/b8c43251402b8869b61e631a22fed0c5.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/3fd0b43d8920dde551490aa4eb57e835.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/0fcbbd06370f32d7d6c8987222260a96.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/07c194c7522f8019f6e3364f96056d78.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/12a77f6ca3b10d2a02308eb20cddb1c4.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/8fc00b5ead4c71b44484ab55c77220ba.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/273/086/003/4b39d77402b42c716156ce4a4d9e92e8.JPG)
Nice job posting Leeku's pictures without even giving him credit.
C'mon Killah, Phil is just trying to taunt me wit' 'dat ALPS.
Sweet unattainable ALPS.
Srsly tho what is the disgusting thing the board is plugged into? That pic is like beauty and the beast.
I might sheepishly ask someone to help me out with a Windows machine to program my Orion :/
-R
Post by: filphil on Thu, 24 September 2015, 05:51:55
Post by: yuktsi on Fri, 25 September 2015, 14:26:58
It's okay. I linked the kbdlab thread to leeku and he also mentioned that it was his thread.Hi Elton! I just sent you a PM.I'll ask if he has extra plate and pcb combos left over.Nothing available
Post by: kacase on Sat, 26 September 2015, 01:27:33
Isn't she a beauty?
Red PCB is now confirmed too. :eek:
(http://i.imgur.com/iyaxDOQ.jpg)
Post by: ika on Sat, 26 September 2015, 02:39:48
Post by: yuktsi on Sat, 26 September 2015, 03:09:12
Post by: Halverson on Sat, 26 September 2015, 03:15:51
Post by: sncbraxsc2 on Sat, 26 September 2015, 06:26:34
I'll tell him to get his ass in here lol
good man
Post by: Rainbow_ on Sat, 26 September 2015, 16:41:47
(http://kbdlab.co.kr/files/attach/images/340/566/093/003/16e1fd2b5cd2a870108a7314a13e2e15.jpg)
Post by: filphil on Sat, 26 September 2015, 16:52:20
Found a photo of one of these assembled on kbdlab...Show Image(http://kbdlab.co.kr/files/attach/images/340/566/093/003/16e1fd2b5cd2a870108a7314a13e2e15.jpg)
So excited
Post by: orcinus on Sat, 26 September 2015, 19:14:16
http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50
:confused:
Wait. Where did the holes above the cursor keys go?
Also, why are there two RGB power LEDs above them?
:eek:
Post by: orcinus on Sat, 26 September 2015, 19:16:39
Show Image(http://i.imgur.com/iyaxDOQ.jpg)
Same question here.
Post by: Fnzzy on Sat, 26 September 2015, 19:36:19
Post by: rsadek on Sun, 27 September 2015, 00:59:57
Didn't you know about the special kbdlab-only option for a special craptastic Orion-without-the-Orionness version?Show Image(http://i.imgur.com/iyaxDOQ.jpg)
Same question here.
Post by: kacase on Sun, 27 September 2015, 05:51:19
Looks like the Orion v1 top housing. It has a thicker bezel. http://duck0113.tistory.com/114
correct me if i'm wrong, but the v1 didnt have those 5 LEDs above the arrows.
http://duck0113.tistory.com/86
Post by: Fnzzy on Sun, 27 September 2015, 07:46:01
Looks like the Orion v1 top housing. It has a thicker bezel. http://duck0113.tistory.com/114
correct me if i'm wrong, but the v1 didnt have those 5 LEDs above the arrows.
http://duck0113.tistory.com/86
Oh I was replying to Orcinus' post where he asked why the Orion in his link didn't have the holes above the arrows.
http://kbdlab.co.kr/index.php?document_srl=3066285&mid=board_Lsno50
:confused:
Wait. Where did the holes above the cursor keys go?
Also, why are there two RGB power LEDs above them?
:eek:
But now that I actually look at the second post he did the guy who got his Orion v2 also doesn't have the holes that we get. I am now confused as well. :confused:
Post by: Rainbow_ on Sun, 27 September 2015, 13:23:30
But now that I actually look at the second post he did the guy who got his Orion v2 also doesn't have the holes that we get. I am now confused as well. :confused:
I can see the LED holes in the assembled one, but I think the one that is just parts is too low quality to see them. It has all of the other characteristics of v2, like the acrylic things that allow light to shine through the side of the board.
Post by: seedvd on Sun, 27 September 2015, 23:06:46
I couldnt see housing designs in those pictures and did hack them with photoshop. They look nicer with thick bezel and bottom aluminum housing with maybe 7 degree angled.
(http://i.imgur.com/TrZ0OXp.jpg)
(http://i.imgur.com/c2q6d2Q.jpg)
Post by: Rainbow_ on Tue, 29 September 2015, 12:21:22
(http://kbdlab.co.kr/files/attach/images/340/372/096/003/7618238ff4eec43e12cf44966d036596.jpg)
Another completed Orion v2!
source (http://kbdlab.co.kr/index.php?document_srl=3096372&mid=board_Lsno50)
Post by: Steezus on Tue, 29 September 2015, 14:03:04
Post by: jaemzp on Tue, 29 September 2015, 18:53:47
Black and red look amazing, I can't wait for the next board for Duck to release. So disappointed I missed this group buy.
Duck Eagle/Viper v2 ;)
Post by: ViệtNV on Tue, 29 September 2015, 23:27:10
Duck Eagle/Viper v2 ;)
i hope so, too :D
Post by: Rainbow_ on Wed, 30 September 2015, 00:24:29
(http://kbdlab.co.kr/files/attach/images/340/733/097/003/96cc3c1efe4c88a1f4b0fd82e8c57f5b.jpg)
(http://kbdlab.co.kr/files/attach/images/340/733/097/003/069068e9c159e171ce258bb4c1b79c43.jpg)
Another one from kbdlab!
Source (http://kbdlab.co.kr/index.php?document_srl=3097733&mid=board_Lsno50)
Post by: swimmingbird on Wed, 30 September 2015, 05:37:00
Black and red look amazing, I can't wait for the next board for Duck to release. So disappointed I missed this group buy.
Duck Eagle/Viper v2 ;)
Man I think I'd buy both if it got run again... or maybe just two vipers :cool:
Post by: jaemzp on Wed, 30 September 2015, 06:04:05
Black and red look amazing, I can't wait for the next board for Duck to release. So disappointed I missed this group buy.
Duck Eagle/Viper v2 ;)
Man I think I'd buy both if it got run again... or maybe just two vipers :cool:
Two is too pricey for me :( Prob get one viper though. Apparently v2 was to have an asymmetric bottom row similar to the hhkb :eek:
Post by: swimmingbird on Wed, 30 September 2015, 06:09:31
Black and red look amazing, I can't wait for the next board for Duck to release. So disappointed I missed this group buy.
Duck Eagle/Viper v2 ;)
Man I think I'd buy both if it got run again... or maybe just two vipers :cool:
Two is too pricey for me :( Prob get one viper though. Apparently v2 was to have an asymmetric bottom row similar to the hhkb :eek:
So it would be 1u/1.5u/6.25u/1.5u/1u like the HHKB?
Post by: ryptide11 on Wed, 30 September 2015, 13:51:29
Post by: Steezus on Wed, 30 September 2015, 23:34:53
Post by: kacase on Thu, 01 October 2015, 09:51:54
Blue-Gray Top w/ Silver Alu Bottom, Gateron blacks and Triumph Adler GMK
all credit to 눈부신눈매™ from kbdlab
(http://i.imgur.com/DJ6zB82.png)
(http://i.imgur.com/1jHR449.png)
(http://i.imgur.com/DvXiZlr.png)
(http://i.imgur.com/EjOZHe6.png)
Post by: Fnzzy on Thu, 01 October 2015, 10:26:02
Post by: Ahkrael on Thu, 01 October 2015, 14:46:48
Post by: orcinus on Thu, 01 October 2015, 18:48:14
Should've stuck with black.
Edit: Or maybe not.
Didn't refresh before replying, so haven't seen the silver until now :D
Post by: elton5354 on Fri, 02 October 2015, 09:21:00
Meanwhile, take a look at their next 75% kustom...
(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Post by: rainb1ood on Fri, 02 October 2015, 09:21:56
Post by: Sed8op8 on Fri, 02 October 2015, 09:23:10
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.stop making new stuff I want Duck haha can't afford it :thumb: thanks Elton exciting stuff and I hope your not to overwhelmed with PMs haha
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Post by: ctrlX on Fri, 02 October 2015, 09:46:03
Post by: digi on Fri, 02 October 2015, 09:50:36
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Uhm, yea, so this will also have Alps support like the Orion!??
SIGN UP FOR THE ALPINE SP GB BOYS!! (it's 60% but you can use blanks or something for the F keys, hehe)
Post by: Rainbow_ on Fri, 02 October 2015, 09:58:33
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Good stuff, elton. Does this mean we get our tracking numbers too? ;)
Post by: elton5354 on Fri, 02 October 2015, 10:11:10
They haven't shipped ours yet, so no tracking..;)
Post by: Sed8op8 on Fri, 02 October 2015, 10:18:09
Post by: E3E on Fri, 02 October 2015, 10:53:09
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Uhm, yea, so this will also have Alps support like the Orion!??
SIGN UP FOR THE ALPINE SP GB BOYS!! (it's 60% but you can use blanks or something for the F keys, hehe)
So it IS an Octagon v2. Fuuuuuuusk my liiiiiife! If it has Alps support, then I am done. Just done. Bye bye wallet.
Post by: ViệtNV on Fri, 02 October 2015, 12:53:55
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Why not Viper/Eagle v2 :'(
Post by: ika on Fri, 02 October 2015, 13:34:51
Post by: yicaoyimu on Fri, 02 October 2015, 13:40:09
Post by: pmh1410 on Fri, 02 October 2015, 13:42:43
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
i hope that USB port is more nice (Like LZMXmini) than Octagon ;)
Post by: digi on Fri, 02 October 2015, 14:04:11
Post by: pichu23 on Fri, 02 October 2015, 16:29:02
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Oh man, If it was a 60%, I'd order one in a heartbeat. :(
Post by: nguyenkimtam on Fri, 02 October 2015, 16:33:23
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.I'm waiting for that , 75% kb is great :thumb:
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
Post by: Jokrik on Sat, 03 October 2015, 04:05:56
Sorry guys, I haven't updated the spreadsheet for a while. I will do it today. NOT to worry. I will read through the PMs and change everything in order.
Meanwhile, take a look at their next 75% kustom...Show Image(http://kbdlab.co.kr/files/attach/images/340/247/104/003/1dbc68a5129cd8beeb68b3746be26303.jpg)
75% in alps, it's like a dream come true
my poor wallet :(
Post by: whentheclouds on Sat, 03 October 2015, 08:59:27
Post by: alienman82 on Sat, 03 October 2015, 13:11:04
Post by: elton5354 on Sat, 03 October 2015, 19:41:49
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
Post by: E3E on Sat, 03 October 2015, 20:08:18
The first 30 will be shipped soon. The rest will follow after a few weeks.
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
The suspense is real. :-X
Well, there has been a LOT of Alps support lately and many in the community are starting to really pay attention to them. Hopefully we can get an Alps PCB!
Post by: blighty on Sat, 03 October 2015, 20:33:26
The first 30 will be shipped soon. The rest will follow after a few weeks.
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
Great news! Now I have to finally decide what switches and caps to put on this...
Post by: KatzenKinder on Sat, 03 October 2015, 20:35:27
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
Post by: njbair on Sat, 03 October 2015, 20:43:51
Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
"Oh hey, look, this must be from that Pay It Forward thing! Oh, my, how generous of my anonymous benefactor!"
Post by: KatzenKinder on Sat, 03 October 2015, 20:44:57
Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
"Oh hey, look, this must be from that Pay It Forward thing! Oh, my, how generous of my anonymous benefactor!"
I've probably abused the "anonymous benefactor" too much already, dunno if that one's gonna fly again.
Post by: njbair on Sat, 03 October 2015, 20:46:47
Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
"Oh hey, look, this must be from that Pay It Forward thing! Oh, my, how generous of my anonymous benefactor!"
I've probably abused the "anonymous benefactor" too much already, dunno if that one's gonna fly again.
Perhaps your cap craft has earned you such a reputation among enthusiasts, that keyboard manufacturers are sending you early releases in order to get a glowing endorsement?
Post by: KatzenKinder on Sat, 03 October 2015, 22:11:53
Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
"Oh hey, look, this must be from that Pay It Forward thing! Oh, my, how generous of my anonymous benefactor!"
I've probably abused the "anonymous benefactor" too much already, dunno if that one's gonna fly again.
Perhaps your cap craft has earned you such a reputation among enthusiasts, that keyboard manufacturers are sending you early releases in order to get a glowing endorsement?
If only I were famous in Korea, then I can go be kpop keyboard star with my Orion
Post by: elton5354 on Sat, 03 October 2015, 23:49:16
The first 30 will be shipped soon. The rest will follow after a few weeks.
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
The suspense is real. :-X
Well, there has been a LOT of Alps support lately and many in the community are starting to really pay attention to them. Hopefully we can get an Alps PCB!
Given that there was an ALPs option in this group buy, there were only 7 orders (2 of which were mine)..so I don't know..
Post by: Rainbow_ on Sun, 04 October 2015, 00:08:51
The first 30 will be shipped soon. The rest will follow after a few weeks.
Very nice!
Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
Is there a problem with saying you bought it (assuming that is what you did)?
Post by: KatzenKinder on Sun, 04 October 2015, 00:53:12
The first 30 will be shipped soon. The rest will follow after a few weeks.
Very nice!Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
Is there a problem with saying you bought it (assuming that is what you did)?
I've had too many boxes come in lately, and the boss is not pleased lolol
But I figured out shipping gonna ship directly to builder, so I can dodge for a bit
Post by: elton5354 on Sun, 04 October 2015, 00:57:36
The first 30 will be shipped soon. The rest will follow after a few weeks.
Very nice!Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
Is there a problem with saying you bought it (assuming that is what you did)?
I've had too many boxes come in lately, and the boss is not pleased lolol
But I figured out shipping gonna ship directly to builder, so I can dodge for a bit
When are you going to make more of those watermelon seed caps??
(https://www.keychatter.com/wp-content/uploads/2015/10/keychatter_2015-10-02_05-07-53.jpg)
Post by: KatzenKinder on Sun, 04 October 2015, 00:58:36
The first 30 will be shipped soon. The rest will follow after a few weeks.
Very nice!Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
Is there a problem with saying you bought it (assuming that is what you did)?
I've had too many boxes come in lately, and the boss is not pleased lolol
But I figured out shipping gonna ship directly to builder, so I can dodge for a bit
When are you going to make more of those watermelon seed caps??Show Image(https://www.keychatter.com/wp-content/uploads/2015/10/keychatter_2015-10-02_05-07-53.jpg)
lol that's KeyKollectiv (Kudos & Koala) not me kekeke
Post by: Want on Sun, 04 October 2015, 05:34:34
Post by: Fnzzy on Sun, 04 October 2015, 14:21:39
Post by: asgeirtj on Sun, 04 October 2015, 15:12:23
Nice! So it's looking probable before Christmas...
Now I just have to figure out how to explain its appearance or smuggle it into my house :v
LOL
Post by: ika on Sun, 04 October 2015, 16:12:19
(http://i.imgur.com/uW5TXwZ.jpg)
Post by: appleonama on Sun, 04 October 2015, 20:00:50
Post by: frostylove on Sun, 04 October 2015, 21:28:21
Well, I was desperate to sell mine because I needed the money but I'm doing well now. I can't wait for this keyboard now.
Oh Please,
tell yourself it's just a fxxking KEYBOARD.
Post by: appleonama on Sun, 04 October 2015, 22:11:31
it is just a keyboard and nothing elseWell, I was desperate to sell mine because I needed the money but I'm doing well now. I can't wait for this keyboard now.
Oh Please,
tell yourself it's just a fxxking KEYBOARD.
its a luxury item and im fully aware of that. I'm still a student who makes a small amount of income doing online jobs but I can manage. if you're tired of keyboards why are you still here :rolleyes:
Post by: Steezus on Sun, 04 October 2015, 22:13:48
it is just a keyboard and nothing elseWell, I was desperate to sell mine because I needed the money but I'm doing well now. I can't wait for this keyboard now.
Oh Please,
tell yourself it's just a fxxking KEYBOARD.
its a luxury item and im fully aware of that. I'm still a student who makes a small amount of income doing so online jobs but I can manage. if you're tired of keyboards why are you still here :rolleyes:
Having interest in keyboards and being on the broke student budget is a bad mix, I'm on the same boat as you. :p
Post by: Sed8op8 on Sun, 04 October 2015, 22:20:42
Also it seems like we are almost there so thanks again Elton and PD for making this possible
Post by: E3E on Sun, 04 October 2015, 22:35:43
I really need to invest in a new soldering iron :eek: can someone in this thread direct me to someone who offers great keyboard assembly service !? I would references from people who have dealt directly with the people they refer if possible :thumb: thanks all
Also it seems like we are almost there so thanks again Elton and PD for making this possible
Well, I did help repair phatdood's Viper PCB
I think I broke my pcb somehow resoldering the switches to gateron blues :-( on my duck viper. Every key works except the 7 key.
Is it possible to get a new pcb? Any tips on fixing it?
Thx so much to E3E for fixing my viper! ;DShow Image(http://i.imgur.com/h80Lw3F.jpg)
Also a buildlog for my Infinity keyboard: http://imgur.com/a/Zrcjx#0
I have desoldered, switch swapped, switch-tuned, and assembled many boards myself, including my Octagon, and I can do repairs up to pad and trace repair (though if your microcontroller is shot, your SOL with me).
I certainly don't mind being a last resort if you'd rather someone who has more history on this site. I did the Viper repair for free. I'd' pretty much just ask you to pay what you feel I should deserve for the assembly. If that's nothing but shipping, then that's fine by me. :)
I can't lie that it'd be cool as hell to see an Orion in the flesh (though my heart will always be with the Octagon <3)
Post by: Ahkrael on Sun, 04 October 2015, 22:41:15
I saw a picture with the LED pins clipped and inserted into pre-soldered pin holders - I'm guessing the board does not come with these clips? I'm talking about the LEDs for the 3 and 5 array strips. Just trying to get a list of everything I would need, and I like the idea of being able to easily clip and try other LEDs if I buy a bunch, than resoldering.
Post by: ika on Sun, 04 October 2015, 22:59:48
I'm also looking to get a soldering station. I've got a few extra QFRs to practice on first - I want to convert one of them from browns to gateron clears.
I saw a picture with the LED pins clipped and inserted into pre-soldered pin holders - I'm guessing the board does not come with these clips? I'm talking about the LEDs for the 3 and 5 array strips. Just trying to get a list of everything I would need, and I like the idea of being able to easily clip and try other LEDs if I buy a bunch, than resoldering.
I think you're talking about SIP sockets. https://geekhack.org/index.php?topic=51792.0
You'll have to push the sockets out of their plastic housing if you want the switch to close completely. http://imgur.com/a/asdXP
Post by: Rainbow_ on Mon, 05 October 2015, 12:57:55
Post by: kacase on Mon, 05 October 2015, 16:57:01
I'm also looking to get a soldering station. I've got a few extra QFRs to practice on first - I want to convert one of them from browns to gateron clears.
I saw a picture with the LED pins clipped and inserted into pre-soldered pin holders - I'm guessing the board does not come with these clips? I'm talking about the LEDs for the 3 and 5 array strips. Just trying to get a list of everything I would need, and I like the idea of being able to easily clip and try other LEDs if I buy a bunch, than resoldering.
I think you're talking about SIP sockets. https://geekhack.org/index.php?topic=51792.0
You'll have to push the sockets out of their plastic housing if you want the switch to close completely. http://imgur.com/a/asdXP
I have a completely different approach on putting in SIP sockets. And just made a little guide. http://imgur.com/a/ewFAz
This is how i made all the switches for my ORION
Post by: Ahkrael on Mon, 05 October 2015, 17:34:22
I'm also looking to get a soldering station. I've got a few extra QFRs to practice on first - I want to convert one of them from browns to gateron clears.
I saw a picture with the LED pins clipped and inserted into pre-soldered pin holders - I'm guessing the board does not come with these clips? I'm talking about the LEDs for the 3 and 5 array strips. Just trying to get a list of everything I would need, and I like the idea of being able to easily clip and try other LEDs if I buy a bunch, than resoldering.
I think you're talking about SIP sockets. https://geekhack.org/index.php?topic=51792.0
You'll have to push the sockets out of their plastic housing if you want the switch to close completely. http://imgur.com/a/asdXP
I have a completely different approach on putting in SIP sockets. And just made a little guide. http://imgur.com/a/ewFAz
This is how i made all the switches for my ORION
Very useful, thank you for the info. I probably won't do much with in-switch LEDs, I'm more concerned with the 3 and 5 array, I'm guessing I can leave the SIP attached to the casing and just solder those on the board.
I'm getting the plastic plate, so I'm thinking there will be a bit of backlight bleed from the underside RGBs, which I like how it looks in the pictures. Either way it's great to have the info on arranging the SIP. Considering I ordered 60 zealios, I'll be modding around 30 other switches to add on the board for the non-alphas, might be a good idea to SIP on those while changing springs just for the future.
Post by: ctrlX on Tue, 06 October 2015, 01:40:17
Money is not a big issue, time is. As long as the build is made with tender loving care and I wouldn't expect anything less from this great community! :)
Only problem is that I am located in Sweden, so shipping it + all parts to the States or Asia is a bit of a drag. Anyone located within the EU that has good experience assembling keyboards and willing to offer their services in exchange for some extra cash?
Post by: Rodgaroon on Tue, 06 October 2015, 09:58:34
Due to limited amount of time (kids :rolleyes:), I am also considering getting mine assembled. Otherwise there is a great risk mine will be finished when V3 is out... :(
Money is not a big issue, time is. As long as the build is made with tender loving care and I wouldn't expect anything less from this great community! :)
Only problem is that I am located in Sweden, so shipping it + all parts to the States or Asia is a bit of a drag. Anyone located within the EU that has good experience assembling keyboards and willing to offer their services in exchange for some extra cash?
https://geekhack.org/index.php?topic=73134.0
Location - Sweden. You are Welcome =)
Post by: ctrlX on Fri, 09 October 2015, 10:52:54
Wicked! Thanks for the tip. :)Due to limited amount of time (kids :rolleyes:), I am also considering getting mine assembled. Otherwise there is a great risk mine will be finished when V3 is out... :(
Money is not a big issue, time is. As long as the build is made with tender loving care and I wouldn't expect anything less from this great community! :)
Only problem is that I am located in Sweden, so shipping it + all parts to the States or Asia is a bit of a drag. Anyone located within the EU that has good experience assembling keyboards and willing to offer their services in exchange for some extra cash?
https://geekhack.org/index.php?topic=73134.0
Location - Sweden. You are Welcome =)
Post by: ramnes on Mon, 12 October 2015, 17:47:58
Post by: rsadek on Fri, 16 October 2015, 23:40:01
These words make no sense together. Like one of those wacky shirts:...just a keyboard...Well, I was desperate to sell mine because I needed the money but I'm doing well now. I can't wait for this keyboard now..... just a fxxking KEYBOARD....
[attach=1]
Post by: ramnes on Tue, 20 October 2015, 07:14:52
I don't see the point of paying Paypal fees if the shipping is done after the protection limit.
Also, Elton, please communicate. That's terrible to be in the dark like we are right now.
Post by: Want on Tue, 20 October 2015, 09:26:44
Am I the only one worried by the fact that my Paypal protection ends in a week for that paiement?
I don't see the point of paying Paypal fees if the shipping is done after the protection limit.
Also, Elton, please communicate. That's terrible to be in the dark like we are right now.
This is a valid concern. My transaction says (roughly translated): "If there's a problem, contact the seller through PayPal before the 20th October 2015", which is today.
I have confidence in Elton delivering a solid product, but expiring safety is always troubling.
Post by: monotagary on Tue, 20 October 2015, 12:13:52
Am I the only one worried by the fact that my Paypal protection ends in a week for that paiement?
I don't see the point of paying Paypal fees if the shipping is done after the protection limit.
Also, Elton, please communicate. That's terrible to be in the dark like we are right now.
Elton has run multiple group buys for Duck's custom boards. He has a stellar track record with handling large amounts of money and getting items out to people in the best condition possible. You have no reason to worry.
Post by: ramnes on Tue, 20 October 2015, 13:04:32
Also, what's the point of paying Paypal fees if we don't use Paypal protection?
Post by: monotagary on Tue, 20 October 2015, 13:11:32
It's not against Elton, I trust him, but if anything happens (package lost, case broken), I feel like I'll be a very bad position.
Also, what's the point of paying Paypal fees if we don't use Paypal protection?
PP fees are paid so that elton doesn't lose money on the buy. Otherwise PP takes a cut directly and he loses out. It just makes it so GBs are more appealing for leaders to run. Also elton will cover anything damaged if you notify him immediately. And also take note that your concerns are totally valid, but elton will take care of us and make sure everyone gets exactly what they paid for.
Post by: ramnes on Tue, 20 October 2015, 15:02:24
PP fees are paid so that elton doesn't lose money on the buy. Otherwise PP takes a cut directly and he loses out.
Then why didn't we just make a payment as gift?
Post by: appleonama on Wed, 21 October 2015, 06:50:41
Post by: Rainbow_ on Wed, 21 October 2015, 07:32:11
There is a higher possibility of me dying before getting this. :rolleyes:
We could arrange that. ;)
Post by: Photoelectric on Wed, 21 October 2015, 11:59:51
Post by: Dreamre on Wed, 21 October 2015, 13:59:29
PP fees are paid so that elton doesn't lose money on the buy. Otherwise PP takes a cut directly and he loses out.
Then why didn't we just make a payment as gift?
I'll gladly take your order if you're sceptical about this GB ;).
Post by: ramnes on Wed, 21 October 2015, 18:00:56
Post by: Rainbow_ on Wed, 21 October 2015, 19:49:07
Well, it's gotta be soon...
Post by: monotagary on Wed, 21 October 2015, 22:01:57
Show Image(http://a.nigger.cat/ojwgnx.png)
Well, it's gotta be soon...
(http://i.imgur.com/vwMin.gif)
Post by: ccc24 on Wed, 21 October 2015, 22:04:54
Post by: monotagary on Wed, 21 October 2015, 22:17:28
anyone have any info on what GB he's running next?
I think Eagle/Viper v2 are next. Not 100% sure though.
Post by: E3E on Wed, 21 October 2015, 22:21:08
anyone have any info on what GB he's running next?
I think Eagle/Viper v2 are next. Not 100% sure though.
Elton showed Duck's plans for an Octagon v2 (if it's going to be called that again, anyway). I think Viper and Eagle v2 will probably be after that, but who knows.
Post by: Fnzzy on Thu, 22 October 2015, 11:34:39
Post by: Steezus on Thu, 22 October 2015, 11:36:28
Isn't there still the next Lightsaver group buy? Not sure what happened to this.
This is the current Duck group buy, once this is done then the next project should be the Octagon v2, then Eagle/Viper v2, and then hopefully a second round of Lightsaver r2. This group buy is near the completion stage waiting for the parts to be shipped.
Post by: wangbwhz on Sat, 24 October 2015, 02:18:20
Post by: nguyenkimtam on Sat, 24 October 2015, 06:05:07
do u know when Octagon GB will start? :DI think it will start next year , because they still not ship Orion v2 for international order :thumb:
Post by: slushi on Sat, 24 October 2015, 15:51:38
Post by: FrostyToast on Sun, 25 October 2015, 09:51:46
This is one of the very few orders with the ALPS combo so I hope that it will get picked up shortly.
FrostyToast
Silver Winkeyless
Acrylic Angled Bottom
Plastic Plate
ALPS Plate and PCB
$433.61
Post by: Rainbow_ on Sun, 25 October 2015, 09:57:41
Hello guys, I am going to let go of my spot for the Orion V2.
This is one of the very few orders with the ALPS combo so I hope that it will get picked up shortly.
FrostyToast
Silver Winkeyless
Acrylic Angled Bottom
Plastic Plate
ALPS Plate and PCB
$433.61
No...
We're so close! :p
Post by: FrostyToast on Sun, 25 October 2015, 10:00:01
Hello guys, I am going to let go of my spot for the Orion V2.
This is one of the very few orders with the ALPS combo so I hope that it will get picked up shortly.
FrostyToast
Silver Winkeyless
Acrylic Angled Bottom
Plastic Plate
ALPS Plate and PCB
$433.61
No...
We're so close! :p
There will be another kustom ALPS board eventually. A TKL board is nothing to cry over.
Still hurts though.
Post by: slushi on Sun, 25 October 2015, 13:02:00
Post by: filphil on Sun, 25 October 2015, 14:07:04
Dangit, I would be all over your order but I was hoping for a MX set :(
His order comes with a plastic plate and mx pcb. If you decide to pick it up I'd be happy to take the alps combo off of you.
That goes to anyone who would want to pick up frosty's order. Lmk!
Post by: slushi on Sun, 25 October 2015, 14:09:29
Dangit, I would be all over your order but I was hoping for a MX set :(
His order comes with a plastic plate and mx pcb. If you decide to pick it up I'd be happy to take the alps combo off of you.
That goes to anyone who would want to pick up frosty's order. Lmk!
Thanks for the heads up! Frosty - you have a PM!
Post by: ccc24 on Sun, 25 October 2015, 23:15:49
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Post by: ika on Mon, 26 October 2015, 00:17:32
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Post by: ccc24 on Mon, 26 October 2015, 00:22:58
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
Post by: ika on Mon, 26 October 2015, 00:26:06
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
Outer diameter and inner diameter. The pin holes on the PCB are the same size, but the Cherry pins themselves are NOT. The OD is what matters when it comes to slotting the sockets into the PCB; the ID is what matters when you want to insert the switch into the sockets.
Now that I think about it I suppose you don't actually NEED the OD to be the same if you plan on soldering all the sockets in. I'm not sure how secure it would be, though. In the smart68 GB thread, feng mentioned the developer of the board worked on it for like two years, so I don't think it's a simple process.
Post by: E3E on Mon, 26 October 2015, 00:35:13
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
Post by: ctrlX on Mon, 26 October 2015, 00:35:56
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?Oh cool. You're trying to mod your Orion so it will be able to do switch hot-swap?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Post by: ccc24 on Mon, 26 October 2015, 00:38:14
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
Outer diameter and inner diameter. The pin holes on the PCB are the same size, but the Cherry pins themselves are NOT. The OD is what matters when it comes to slotting the sockets into the PCB; the ID is what matters when you want to insert the switch into the sockets.
Now that I think about it I suppose you don't actually NEED the OD to be the same if you plan on soldering all the sockets in. I'm not sure how secure it would be, though. In the smart68 GB thread, feng mentioned the developer of the board worked on it for like two years, so I don't think it's a simple process.
ahh ok i see what your'e saying. Yeah I think the issue would be getting the correct outer diameter to fit with the pcb, because digikey does offer different sizes and I can always buy a few to test with the switches but I don't have the pcb to test with on hand. But I saw some posts and threads about people testing it, and the website says the termination type is solder so it seems pretty straight forward ;D. But I think what the smart68 had to accomplish was doing all of it on a mass production scale.
Post by: ccc24 on Mon, 26 October 2015, 00:44:04
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
Yeah I saw
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes
Post by: ccc24 on Mon, 26 October 2015, 00:44:42
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes that ika was talking about. And he uses ones that don't require solder. I think his main issue was his PCB had different layout so his switch mounting points weren't completely circular and a bit ovalish. I guess I just need to wait to see more info on the octagon pcb.
Post by: E3E on Mon, 26 October 2015, 01:38:51
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes that ika was talking about. And he uses ones that don't require solder. I think his main issue was his PCB had different layout so his switch mounting points weren't completely circular and a bit ovalish. I guess I just need to wait to see more info on the octagon pcb.
Are you planning on doing this for the Octagon or for the Orion v2? If you check out some of the pics, the holes on his winkeyless.kr PCB are round, not oval, so these receptacles should fit no problem. The problems he mentions were because of the switch pin holes running into the cutouts for the stem well on the bottom of the switch. Since they are solderless, they had to be secured more sturdily. These can also be soldered too though, but they should hold solidly and be flush fitting if the size of the whole is correct.
The measurements I got when checking the ID of the switch pin holes in a Duck Lightpad PCB were around 1.55mm.
The measurements I got in Cherry pins were .80mm for the smaller stout pin and 1mm for the wider, leafy pin.
Post by: ccc24 on Mon, 26 October 2015, 12:09:57
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes that ika was talking about. And he uses ones that don't require solder. I think his main issue was his PCB had different layout so his switch mounting points weren't completely circular and a bit ovalish. I guess I just need to wait to see more info on the octagon pcb.
Are you planning on doing this for the Octagon or for the Orion v2? If you check out some of the pics, the holes on his winkeyless.kr PCB are round, not oval, so these receptacles should fit no problem. The problems he mentions were because of the switch pin holes running into the cutouts for the stem well on the bottom of the switch. Since they are solderless, they had to be secured more sturdily. These can also be soldered too though, but they should hold solidly and be flush fitting if the size of the whole is correct.
The measurements I got when checking the ID of the switch pin holes in a Duck Lightpad PCB were around 1.55mm.
The measurements I got in Cherry pins were .80mm for the smaller stout pin and 1mm for the wider, leafy pin.
Sweet thanks yeah I'm going to buy different kinds of receptacles that fit those dimensions and see which work best. I missed out on this GB so I hope to test it out on whatever the next GB is, which I hear is the octagon. I posted here because people seem to be more active, and i'm sure the pcb's have similar specs when it comes to the mounting point of the switches.
Post by: Want on Mon, 26 October 2015, 13:09:38
Update?
It's been a while since we heard "shipping soon".
Post by: ccc24 on Mon, 26 October 2015, 18:11:56
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes that ika was talking about. And he uses ones that don't require solder. I think his main issue was his PCB had different layout so his switch mounting points weren't completely circular and a bit ovalish. I guess I just need to wait to see more info on the octagon pcb.
Are you planning on doing this for the Octagon or for the Orion v2? If you check out some of the pics, the holes on his winkeyless.kr PCB are round, not oval, so these receptacles should fit no problem. The problems he mentions were because of the switch pin holes running into the cutouts for the stem well on the bottom of the switch. Since they are solderless, they had to be secured more sturdily. These can also be soldered too though, but they should hold solidly and be flush fitting if the size of the whole is correct.
The measurements I got when checking the ID of the switch pin holes in a Duck Lightpad PCB were around 1.55mm.
The measurements I got in Cherry pins were .80mm for the smaller stout pin and 1mm for the wider, leafy pin.
do you also know what he means when he says he centre punched and hammered the inserts into the pcb? Does he mean he literally just banged them into the pcb?
Post by: E3E on Mon, 26 October 2015, 20:10:14
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes that ika was talking about. And he uses ones that don't require solder. I think his main issue was his PCB had different layout so his switch mounting points weren't completely circular and a bit ovalish. I guess I just need to wait to see more info on the octagon pcb.
Are you planning on doing this for the Octagon or for the Orion v2? If you check out some of the pics, the holes on his winkeyless.kr PCB are round, not oval, so these receptacles should fit no problem. The problems he mentions were because of the switch pin holes running into the cutouts for the stem well on the bottom of the switch. Since they are solderless, they had to be secured more sturdily. These can also be soldered too though, but they should hold solidly and be flush fitting if the size of the whole is correct.
The measurements I got when checking the ID of the switch pin holes in a Duck Lightpad PCB were around 1.55mm.
The measurements I got in Cherry pins were .80mm for the smaller stout pin and 1mm for the wider, leafy pin.
do you also know what he means when he says he centre punched and hammered the inserts into the pcb? Does he mean he literally just banged them into the pcb?
Yeah, I talked to him a ton through the messaging system on that forum to get my plans for an Alps-build with hotswapping figured out.
Yeah, he did actually hammer the pins in, but he did say in the end, that simply heating the sockets with a soldering iron and pushing them in made the process a lot easier. So that's what I'd go for if you plan on doing this. Taking a hammer and a punch sounds insanely dangerous for both your fingers, the sockets, and the PCB. :P
Post by: ccc24 on Mon, 26 October 2015, 20:39:58
anyone know/think these pin receptacles could fit in the duck PCB? The datasheet says the diameter is .058mm..so could anyone tell me the diameter of the the switch mounting hole?
edit:sorry forgot to include the link https://www.digikey.com/product-detail/en/0305-2-15-15-47-27-10-0/ED90333-ND/1801940
Are you intending to use these as hot-swap receptacles? Keep in mind that you'll have to use two different kinds of sockets, since Cherry switch pins are different widths. You'll need the same OD and different IDs. That said, I hope someone has an answer for you, because it sounds interesting!
Yeah I am, I was actually hoping to test them out on zealios first. But what do you mean by OD and ID?
https://linustechtips.com/main/topic/430702-custom-keyboard-hot-swapable-switch-build/
This is an excellent read if you're looking into hotswapping.
okay nice yeah it seems like he used a different receptacle to fix the issue he had of the different cherry pin sizes that ika was talking about. And he uses ones that don't require solder. I think his main issue was his PCB had different layout so his switch mounting points weren't completely circular and a bit ovalish. I guess I just need to wait to see more info on the octagon pcb.
Are you planning on doing this for the Octagon or for the Orion v2? If you check out some of the pics, the holes on his winkeyless.kr PCB are round, not oval, so these receptacles should fit no problem. The problems he mentions were because of the switch pin holes running into the cutouts for the stem well on the bottom of the switch. Since they are solderless, they had to be secured more sturdily. These can also be soldered too though, but they should hold solidly and be flush fitting if the size of the whole is correct.
The measurements I got when checking the ID of the switch pin holes in a Duck Lightpad PCB were around 1.55mm.
The measurements I got in Cherry pins were .80mm for the smaller stout pin and 1mm for the wider, leafy pin.
do you also know what he means when he says he centre punched and hammered the inserts into the pcb? Does he mean he literally just banged them into the pcb?
Yeah, I talked to him a ton through the messaging system on that forum to get my plans for an Alps-build with hotswapping figured out.
Yeah, he did actually hammer the pins in, but he did say in the end, that simply heating the sockets with a soldering iron and pushing them in made the process a lot easier. So that's what I'd go for if you plan on doing this. Taking a hammer and a punch sounds insanely dangerous for both your fingers, the sockets, and the PCB. :P
haha ok I see. So the receptacle data sheet says the mounting hole diameter is 1.47mm and you said the duck pcb is around 1.55mm. You think that'll be fine? Or does it have to be completely flush with the trace for it to work?
Post by: E3E on Mon, 26 October 2015, 20:47:59
haha ok I see. So the receptacle data sheet says the mounting hole diameter is 1.47mm and you said the duck pcb is around 1.55mm. You think that'll be fine? Or does it have to be completely flush with the trace for it to work?
I can't say with the utmost certainty as, for my case, I'll have to be drilling out the holes a slight amount because the only receptacles that would work with Alps are too wide to just slip in. I can't imagine the through holes being so off between the WKL.kr PCB and the Duck that it won't work. The next size up on those is a 1.60mm diameter. I'd say going a little less might be a better idea.
If you are worried, then try ordering a small amount of both sizes to see which works best for ya! Maybe we should take this to PM too by the way, unless the guys here don't mind our conversation here.
Post by: ccc24 on Mon, 26 October 2015, 20:51:17
haha ok I see. So the receptacle data sheet says the mounting hole diameter is 1.47mm and you said the duck pcb is around 1.55mm. You think that'll be fine? Or does it have to be completely flush with the trace for it to work?
I can't say with the utmost certainty as, for my case, I'll have to be drilling out the holes a slight amount because the only receptacles that would work with Alps are too wide to just slip in. I can't imagine the through holes being so off between the WKL.kr PCB and the Duck that it won't work. The next size up on those is a 1.60mm diameter. I'd say going a little less might be a better idea.
If you are worried, then try ordering a small amount of both sizes to see which works best for ya! Maybe we should take this to PM too by the way, unless the guys here don't mind our conversation here.
ok sounds good, yeah i'll try different sizes..I'll pm you if I have any more questions.
Post by: romevi on Mon, 26 October 2015, 21:10:05
The first 30 will be shipped soon. The rest will follow after a few weeks.Sweet. If I can get in on this then this'll be my first Duck. Hopefully it'll have Alps.
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
Will this thread be the best way to get updated on that? Don't mean to hijack the Orion line just for the Octagon.
Also, how many Orion boards were successfully ordered after the first 30? Just want to know the chances of getting on the Octagon.
Post by: ika on Mon, 26 October 2015, 21:20:59
Post by: Rainbow_ on Mon, 26 October 2015, 21:32:01
The first 30 will be shipped soon. The rest will follow after a few weeks.Sweet. If I can get in on this then this'll be my first Duck. Hopefully it'll have Alps.
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
Will this thread be the best way to get updated on that? Don't mean to hijack the Orion line just for the Octagon.
Also, how many Orion boards were successfully ordered after the first 30? Just want to know the chances of getting on the Octagon.
IIRC GH only got 60 units.
Post by: E3E on Mon, 26 October 2015, 22:07:44
The first 30 will be shipped soon. The rest will follow after a few weeks.Sweet. If I can get in on this then this'll be my first Duck. Hopefully it'll have Alps.
Regarding alps for the new 75% I am not sure they will go along with it unless there are significant interest in it. If there are they can get leeku to make them as an add on.
Will this thread be the best way to get updated on that? Don't mean to hijack the Orion line just for the Octagon.
Also, how many Orion boards were successfully ordered after the first 30? Just want to know the chances of getting on the Octagon.
Pretty sure the Octagon v2 is going to happen. The main uncertainty is whether or not an Alps PCB will be included or not.
Post by: elton5354 on Wed, 28 October 2015, 13:46:51
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Post by: FrostyToast on Wed, 28 October 2015, 13:52:40
I've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Elton I have sent an inquiry via pm. I don't know if you got it.
I am in the latter half of the orders so I hope that they can be addressed.
Post by: elton5354 on Wed, 28 October 2015, 13:53:28
I've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Elton I have sent an inquiry via pm. I don't know if you got it.
I am in the latter half of the orders so I hope that they can be addressed.
I got it. It will be done tonight.
Post by: filphil on Wed, 28 October 2015, 13:59:47
I've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
(https://media.giphy.com/media/ZsiFSuU8YVfwc/giphy.gif)
Post by: Halverson on Wed, 28 October 2015, 14:01:49
I've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
RIOT!!!
Post by: rainb1ood on Wed, 28 October 2015, 14:24:53
Post by: Rainbow_ on Wed, 28 October 2015, 14:48:52
Post by: monotagary on Wed, 28 October 2015, 14:51:32
Post by: Sed8op8 on Wed, 28 October 2015, 15:04:29
Post by: Want on Wed, 28 October 2015, 15:40:45
Post by: R1N3 on Wed, 28 October 2015, 15:44:31
Post by: Frizer on Wed, 28 October 2015, 16:22:44
Post by: Pemdas on Wed, 28 October 2015, 16:38:17
I've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Yesssssss! So just to make sure, do we need anything other than switches, leds, and stabilizers?
Post by: monotagary on Wed, 28 October 2015, 18:08:34
I've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Yesssssss! So just to make sure, do we need anything other than switches, leds, and stabilizers?
Correct. The PCB parts are presoldered, so the kits will be ready to go with just switches and stabs. And LEDs if you're into that sort of thing. :p
Post by: appleonama on Wed, 28 October 2015, 20:33:39
The whole keyboard is a light show. Pretty sure everyone bought it to make a light showI've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Yesssssss! So just to make sure, do we need anything other than switches, leds, and stabilizers?
Correct. The PCB parts are presoldered, so the kits will be ready to go with just switches and stabs. And LEDs if you're into that sort of thing. :p
Post by: E3E on Wed, 28 October 2015, 20:39:19
The whole keyboard is a light show. Pretty sure everyone bought it to make a light showI've received an update regarding the first 30 orders are packed and are waiting to be picked up. Hopefully we get it by next week!
I will update the order changes tonight.
On behalf of truecustom, I apologize to everyone about the long delays.
Yesssssss! So just to make sure, do we need anything other than switches, leds, and stabilizers?
Correct. The PCB parts are presoldered, so the kits will be ready to go with just switches and stabs. And LEDs if you're into that sort of thing. :p
Except the Alps versions. They won't be as much of a light show, but the RGB will still be nice. :)
Post by: orcinus on Wed, 28 October 2015, 21:11:12
Yesssssss! So just to make sure, do we need anything other than switches, leds, and stabilizers?
Yes we do. An Orion v2.
Post by: CyriusG on Thu, 29 October 2015, 03:13:19
Post by: appleonama on Thu, 29 October 2015, 07:38:06
Post by: E3E on Thu, 29 October 2015, 07:51:56
ugh im not first 30 gg im probably going to randomly have a stroke tomrrow
... And that'll make the next in line very happy! Don't get people's hopes up now. >:D
Post by: alienman82 on Thu, 29 October 2015, 12:21:34
ugh im not first 30 gg im probably going to randomly have a stroke tomrrow
I feel you #34
Post by: kacase on Thu, 29 October 2015, 13:19:50
Post by: rainb1ood on Thu, 29 October 2015, 13:20:56
Post by: Fnzzy on Thu, 29 October 2015, 14:05:44
Post by: kacase on Thu, 29 October 2015, 17:10:39
He just did a few posts agooh
i feel pretty stupid :D
Post by: elton5354 on Fri, 30 October 2015, 12:25:13
Post by: alienman82 on Fri, 30 October 2015, 12:27:19
I'll have the tracking #s for the first 30 tonight or tomorrow.
Any estimates for the next 30?
Post by: monotagary on Fri, 30 October 2015, 13:07:03
I'll have the tracking #s for the first 30 tonight or tomorrow.
*S C R E A M I N G E X C I T E D L Y*
Post by: Rainbow_ on Fri, 30 October 2015, 13:24:00
I'll have the tracking #s for the first 30 tonight or tomorrow.
I'm hype.
Post by: Fnzzy on Fri, 30 October 2015, 13:31:18
still don't have the right switches ffs
Post by: Ahkrael on Fri, 30 October 2015, 14:01:37
Post by: hatran87 on Fri, 30 October 2015, 15:35:40
Or we must wait for the next round GB?
Post by: FrostyToast on Fri, 30 October 2015, 15:45:11
Hi Elton, do you have any spot for the Orion V2 now ?
Or we must wait for the next round GB?
Orders have been closed for a long time.
You will have to wait for another round. That is, if there is ever another round.
Post by: aznairjordan on Fri, 30 October 2015, 15:45:53
Hi Elton, do you have any spot for the Orion V2 now ?
Or we must wait for the next round GB?
Try picking up an order from someone getting rid of theirs if you are interested in the parts that they ordered.
Post by: Pemdas on Fri, 30 October 2015, 18:11:26
I'll have the tracking #s for the first 30 tonight or tomorrow.
Oh man I'm feeling all anxious now :))
Post by: E3E on Fri, 30 October 2015, 18:18:02
Hi Elton, do you have any spot for the Orion V2 now ?
Or we must wait for the next round GB?
Orders have been closed for a long time.
You will have to wait for another round. That is, if there is ever another round.
If I was one for TKLs, this comment would be way 2spooky3me :'(
Post by: duzeyao on Fri, 30 October 2015, 21:39:02
:thumb: :thumb: :thumb:
Post by: FrostyToast on Fri, 30 October 2015, 21:42:56
Hi Elton, do you have any spot for the Orion V2 now ?
Or we must wait for the next round GB?
Orders have been closed for a long time.
You will have to wait for another round. That is, if there is ever another round.
If I was one for TKLs, this comment would be way 2spooky3me :'(
Well I think the bigger picture here is that if there isn't a second round for this board then there will be a v3 or something of the like.
The only time when a TKL from truecustom is out of the question is when he stops making boards.
Post by: E3E on Fri, 30 October 2015, 21:46:41
Hi Elton, do you have any spot for the Orion V2 now ?
Or we must wait for the next round GB?
Orders have been closed for a long time.
You will have to wait for another round. That is, if there is ever another round.
If I was one for TKLs, this comment would be way 2spooky3me :'(
Well I think the bigger picture here is that if there isn't a second round for this board then there will be a v3 or something of the like.
The only time when a TKL from truecustom is out of the question is when he stops making boards.
I getcha. I'd rather see things evolve rather than stay in the same iteration for too long. It's why I'm more a fan of seeing a Lightsaver v3 over seeing another round of v2.
I'm definitely psyched at the prospect of an Octagon v2. I wonder if it will still even be called by that name. :P
Post by: elton5354 on Sat, 31 October 2015, 09:59:04
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
It's about another month for the rest to be ready to ship.
Post by: Rainbow_ on Sat, 31 October 2015, 10:17:18
just gotta wait for customs now...
Post by: CyriusG on Sat, 31 October 2015, 10:25:12
Post by: rainb1ood on Sat, 31 October 2015, 10:59:53
mine is in JFK airport nowSame with mine. Looks like we'll be getting these this week!
just gotta wait for customs now...
Post by: tuantruong on Sat, 31 October 2015, 11:11:08
Tracking #s are updated for some.. Due to some problems manufacturing the acrylic angled bottom casings, there weren't many available to ship hence the mixed of order in shipping.So the rest of 1st 30 orders has to wait for another month? :'(
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
It's about another month for the rest to be ready to ship.
Post by: ika on Sat, 31 October 2015, 11:17:34
Post by: kacase on Sat, 31 October 2015, 11:23:40
Thank you for all the hard work Elton!
Do you know about what value true custom declared on the package? Just so I can go to customs prepared. ;D
Post by: Frizer on Sat, 31 October 2015, 12:07:52
Post by: Want on Sat, 31 October 2015, 12:39:53
Post by: Pemdas on Sat, 31 October 2015, 13:19:08
Tracking #s are updated for some.. Due to some problems manufacturing the acrylic angled bottom casings, there weren't many available to ship hence the mixed of order in shipping.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
It's about another month for the rest to be ready to ship.
Dang was so close :( so if we don't have a tracking number right now and were in the first 30 we have to wait another month?
*edit* would it be possible to have an option to pay more for shipping and have the parts that are ready ship now? I wouldn't mind having getting the acrylic bottom a month after getting the rest :p
Post by: duzeyao on Sun, 01 November 2015, 03:22:02
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
Post by: Rainbow_ on Sun, 01 November 2015, 09:25:14
it's just so beautiful
Post by: alienman82 on Sun, 01 November 2015, 09:27:27
Just received mine, safe and sound. It's in perfect condition and I'm gonna assemble it right away.
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
PICTURES PICTURES!!!
Post by: duzeyao on Mon, 02 November 2015, 02:26:58
Just received mine, safe and sound. It's in perfect condition and I'm gonna assemble it right away.
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
PICTURES PICTURES!!!
(http://ww1.sinaimg.cn/mw690/54b7b013gw1exmpfvc6f6j24802tcx6s.jpg)
(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpfir206j24802tcqv7.jpg)
(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpesw73gj24802tcu10.jpg)
(http://ww3.sinaimg.cn/mw690/54b7b013gw1exmpczmgojj24802tc1l1.jpg)
(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpcnd80qj24802tc7wk.jpg)
For original sized pictures and more you can check: (click 查看大图)
http://photo.weibo.com/1421324307/albums/detail/album_id/3904765762372638#!/mode/1/page/1
The blue-grey + silver case is from Elton. The full black case is ordered from another source.
Post by: E3E on Mon, 02 November 2015, 02:47:01
Just received mine, safe and sound. It's in perfect condition and I'm gonna assemble it right away.
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
PICTURES PICTURES!!!Show Image(http://ww1.sinaimg.cn/mw690/54b7b013gw1exmpfvc6f6j24802tcx6s.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpfir206j24802tcqv7.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpesw73gj24802tcu10.jpg)Show Image(http://ww3.sinaimg.cn/mw690/54b7b013gw1exmpczmgojj24802tc1l1.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpcnd80qj24802tc7wk.jpg)
For original sized pictures and more you can check: (click 查看大图)
http://photo.weibo.com/1421324307/albums/detail/album_id/3904765762372638#!/mode/1/page/1
The blue-grey + silver case is from Elton. The full black case is ordered from another source.
Sorry for my confusion, but did you buy a second Orion from Elton, or is that just Elton's for whatever reason?
Post by: duzeyao on Mon, 02 November 2015, 03:55:31
Just received mine, safe and sound. It's in perfect condition and I'm gonna assemble it right away.
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
PICTURES PICTURES!!!Show Image(http://ww1.sinaimg.cn/mw690/54b7b013gw1exmpfvc6f6j24802tcx6s.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpfir206j24802tcqv7.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpesw73gj24802tcu10.jpg)Show Image(http://ww3.sinaimg.cn/mw690/54b7b013gw1exmpczmgojj24802tc1l1.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpcnd80qj24802tc7wk.jpg)
For original sized pictures and more you can check: (click 查看大图)
http://photo.weibo.com/1421324307/albums/detail/album_id/3904765762372638#!/mode/1/page/1
The blue-grey + silver case is from Elton. The full black case is ordered from another source.
Sorry for my confusion, but did you buy a second Orion from Elton, or is that just Elton's for whatever reason?
A BlueGrey + Silver from Elton and a Black + Black from local vendor. :rolleyes:
Post by: E3E on Mon, 02 November 2015, 04:04:11
Just received mine, safe and sound. It's in perfect condition and I'm gonna assemble it right away.
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
PICTURES PICTURES!!!Show Image(http://ww1.sinaimg.cn/mw690/54b7b013gw1exmpfvc6f6j24802tcx6s.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpfir206j24802tcqv7.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpesw73gj24802tcu10.jpg)Show Image(http://ww3.sinaimg.cn/mw690/54b7b013gw1exmpczmgojj24802tc1l1.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpcnd80qj24802tc7wk.jpg)
For original sized pictures and more you can check: (click 查看大图)
http://photo.weibo.com/1421324307/albums/detail/album_id/3904765762372638#!/mode/1/page/1
The blue-grey + silver case is from Elton. The full black case is ordered from another source.
Sorry for my confusion, but did you buy a second Orion from Elton, or is that just Elton's for whatever reason?
A BlueGrey + Silver from Elton and a Black + Black from local vendor. :rolleyes:
So you do have two. I was wondering if you simply had Elton's for some reason, as in, he did not sell it to you, but it was in your possession. :P
Have fun!
Post by: ramnes on Mon, 02 November 2015, 05:58:46
Acrylic inserts?
Post by: appleonama on Mon, 02 November 2015, 08:16:16
Post by: Fnzzy on Mon, 02 November 2015, 12:29:19
Post by: filphil on Mon, 02 November 2015, 13:23:06
(http://i.imgur.com/lIxSucT.jpg)
Post by: R1N3 on Mon, 02 November 2015, 13:31:09
Almost timeI can't ****ing wait!Show Image(http://i.imgur.com/lIxSucT.jpg)
Which springs did you get in your zealios?
Post by: filphil on Mon, 02 November 2015, 13:43:18
Almost timeI can't ****ing wait!Show Image(http://i.imgur.com/lIxSucT.jpg)
Which springs did you get in your zealios?
I was JUST in atlanta over the weekend btw!
The setup is unmodified 62g zealios and semi-clipped stabilizers. The leg of the stabs were only clipped to remove the pointed 90 degree ends rather than the whole leg people would usually do. Since OG red alert is being used I'm sure this set will see the mods being switched out a few times and this was a precaution against cherry stabs getting pulled off.
Post by: ctrlX on Mon, 02 November 2015, 13:53:35
Almost timeHow did the soldering go? According to the Zealios GB thread some have had issues with the switches being a bit sensitive to the heat from the soldering iron. Causing the plastic to deform and ruining the actuation etc.Show Image(http://i.imgur.com/lIxSucT.jpg)
Post by: filphil on Mon, 02 November 2015, 14:15:24
Almost timeHow did the soldering go? According to the Zealios GB thread some have had issues with the switches being a bit sensitive to the heat from the soldering iron. Causing the plastic to deform and ruining the actuation etc.Show Image(http://i.imgur.com/lIxSucT.jpg)
The switches aren't soldered yet. Just mounted it to get ready got soldering tomorrow and to make sure I got the bottom row how I wanted it.
I'll report and issues with zeal's switches in his group buy thread.
Post by: R1N3 on Mon, 02 November 2015, 14:39:16
Damn bro you shoulda hit me up!Almost timeI can't ****ing wait!Show Image(http://i.imgur.com/lIxSucT.jpg)
Which springs did you get in your zealios?
I was JUST in atlanta over the weekend btw!
The setup is unmodified 62g zealios and semi-clipped stabilizers. The leg of the stabs were only clipped to remove the pointed 90 degree ends rather than the whole leg people would usually do. Since OG red alert is being used I'm sure this set will see the mods being switched out a few times and this was a precaution against cherry stabs getting pulled off.
Post by: blighty on Mon, 02 November 2015, 14:59:38
*edit: It seems the positive side of the led is the farthest from the resistor/ + side on left side of switch when inserting into switch/pcb when not marked otherwise
Link that might help others:
http://duck0113.tistory.com/84 (http://duck0113.tistory.com/84) Breakdown on getting the keymapper up and running, and installing flip/java for firmware upload and atmel usb drivers
*
Ended up going with gateron reds with red leds with caps from a g80-1000 (black winkeyless/ss plate/acrylic wedge). I'll post pics tomorrow if anyone is interested. :thumb:
I have to say the the packaging for this was even more robust than the last Lightsaver buy. Thanks again for running this, elton!
Post by: Steezus on Mon, 02 November 2015, 21:09:50
Anyone know a quick way to tell LED polarity on the Orion V2 pcb? It seems only switch holes with multiple positions have it marked.
*edit: It seems the positive side of the led is the farthest from the resistor/ + side on left side of switch when inserting into switch/pcb when not marked otherwise
Link that might help others:
http://duck0113.tistory.com/84 (http://duck0113.tistory.com/84) Breakdown on getting the keymapper up and running, and installing flip/java for firmware upload and atmel usb drivers
*
Ended up going with gateron reds with red leds with caps from a g80-1000 (black winkeyless/ss plate/acrylic wedge). I'll post pics tomorrow if anyone interested. :thumb:
I have to say the the packaging for this was even more robust than the last Lightsaver buy. Thanks again for running this elton!
Haven't seen the PCB yet but usually square is positive and oval is negative if it happens to look like this.
[attachimg=1]
Post by: blighty on Mon, 02 November 2015, 21:20:44
Anyone know a quick way to tell LED polarity on the Orion V2 pcb? It seems only switch holes with multiple positions have it marked.
*edit: It seems the positive side of the led is the farthest from the resistor/ + side on left side of switch when inserting into switch/pcb when not marked otherwise
Link that might help others:
http://duck0113.tistory.com/84 (http://duck0113.tistory.com/84) Breakdown on getting the keymapper up and running, and installing flip/java for firmware upload and atmel usb drivers
*
Ended up going with gateron reds with red leds with caps from a g80-1000 (black winkeyless/ss plate/acrylic wedge). I'll post pics tomorrow if anyone interested. :thumb:
I have to say the the packaging for this was even more robust than the last Lightsaver buy. Thanks again for running this elton!
Haven't seen the PCB yet but usually square is positive and oval is negative if it happens to look like this.
(Attachment Link)
Already got it assembled, but i'm pretty sure there it's all circles. Only the bottom row mods have printed "+" symbols, use dependent use of 1.25 or 1.5u mods.
Post by: gadzkun on Tue, 03 November 2015, 02:47:40
any news about duck next GB?
for next i really dont want to miss it.. :-[
Post by: kacase on Tue, 03 November 2015, 02:48:58
Will having an LED inserted "the wrong way round" have a negative effect except that no light is being emitted? E.g. does it make the LED break or even worse does anything happen to the pcb?
It would be great if somebody could give me an answer to that! :thumb:
Post by: gadzkun on Tue, 03 November 2015, 02:56:05
quick question. I was stupid and completely forgot about LED Polarity when assembling my switches. So chances are that 50% of my assembled switches will be "the wrong way round". As I am using SIP Sockets, changing polarity shouldnt be too much of a hassle. I was planning on soldering all the switches and then see which LEDs I have to flip.
Will having an LED inserted "the wrong way round" have a negative effect except that no light is being emitted? E.g. does it make the LED break or even worse does anything happen to the pcb?
It would be great if somebody could give me an answer to that! :thumb:
i think it wont do any damage. only make the led wont work.
just like inserted wrong battery, it wont ON but not damaged.
but maybe im wrong ;D
Post by: E3E on Tue, 03 November 2015, 03:36:44
quick question. I was stupid and completely forgot about LED Polarity when assembling my switches. So chances are that 50% of my assembled switches will be "the wrong way round". As I am using SIP Sockets, changing polarity shouldnt be too much of a hassle. I was planning on soldering all the switches and then see which LEDs I have to flip.
Will having an LED inserted "the wrong way round" have a negative effect except that no light is being emitted? E.g. does it make the LED break or even worse does anything happen to the pcb?
It would be great if somebody could give me an answer to that! :thumb:
i think it wont do any damage. only make the led wont work.
just like inserted wrong battery, it wont ON but not damaged.
but maybe im wrong ;D
As someone who's dealt with SIPs a ton, you'll be fine. In practical terms and through experience assembling boards and changing out LEDs, there is no harm to the board when it comes putting in LEDs the wrong way around, just that it's a major PITA if you SOLDERED them all that way.
Post by: Ahkrael on Tue, 03 November 2015, 03:51:33
I'm SUPER impressed with the quality of the machining on the alum top. I love how the LED cutouts are done - with the pinholes on top of the dome cuts. I got the angled bottom and it is SOLID. I'm still going to toy around with different spring weights for some of the keys before I solder it together - I only got 60 of the 65g Zealios. I'm thinking of mixing some other springs with Gat linears - 65g Zeals would be roughly equal to what actuation weight? I have some Sprits 78 (2 pcs), 72, 62 and 68 (which are weighted for total compression) and some Gateron springs (massdrop) which are weighted for actuation at 62, 45, and 80 (super heavy). I've got more gat browns if I want more tactiles, but if they are going to be different I might as well do linears, is my thinking.
Post by: E3E on Tue, 03 November 2015, 03:57:04
I just received my board, and though I haven't tested it, the other poster earlier said that polarity should be Positive on the Farthest circle from the Resistor. Basically, if you are looking at the Front of the PCB, it would mean Pos is Left, as when you flip it over, the resistors are on the Left, so pos is Right on the reverse side of board. I'm assuming this is the same for the other LEDs as well.
I'm SUPER impressed with the quality of the machining on the alum top. I love how the LED cutouts are done - with the pinholes on top of the dome cuts. I got the angled bottom and it is SOLID. I'm still going to toy around with different spring weights for some of the keys before I solder it together - I only got 60 of the 65g Zealios. I'm thinking of mixing some other springs with Gat linears - 65g Zeals would be roughly equal to what actuation weight? I have some Sprits 78 (2 pcs), 72, 62 and 68 (which are weighted for total compression) and some Gateron springs (massdrop) which are weighted for actuation at 62, 45, and 80 (super heavy). I've got more gat browns if I want more tactiles, but if they are going to be different I might as well do linears, is my thinking.
I'm pretty sure that Zeal weighted his switches using the Korean standard, so the weight should be most similar to the 62g and 68g SPRiT springs you have.
If the Gateton 45g springs are anything like Cherry MX reds, then the bottom out weight should be 60g.
Post by: kacase on Tue, 03 November 2015, 04:37:20
quick question. I was stupid and completely forgot about LED Polarity when assembling my switches. So chances are that 50% of my assembled switches will be "the wrong way round". As I am using SIP Sockets, changing polarity shouldnt be too much of a hassle. I was planning on soldering all the switches and then see which LEDs I have to flip.
Will having an LED inserted "the wrong way round" have a negative effect except that no light is being emitted? E.g. does it make the LED break or even worse does anything happen to the pcb?
It would be great if somebody could give me an answer to that! :thumb:
i think it wont do any damage. only make the led wont work.
just like inserted wrong battery, it wont ON but not damaged.
but maybe im wrong ;D
As someone who's dealt with SIPs a ton, you'll be fine. In practical terms and through experience assembling boards and changing out LEDs, there is no harm to the board when it comes putting in LEDs the wrong way around, just that it's a major PITA if you SOLDERED them all that way.
Thanks a ton for your help! I guess ill just solder all my switches and flip the LEDs that dont light up :)
Post by: gadzkun on Tue, 03 November 2015, 04:49:04
quick question. I was stupid and completely forgot about LED Polarity when assembling my switches. So chances are that 50% of my assembled switches will be "the wrong way round". As I am using SIP Sockets, changing polarity shouldnt be too much of a hassle. I was planning on soldering all the switches and then see which LEDs I have to flip.
Will having an LED inserted "the wrong way round" have a negative effect except that no light is being emitted? E.g. does it make the LED break or even worse does anything happen to the pcb?
It would be great if somebody could give me an answer to that! :thumb:
i think it wont do any damage. only make the led wont work.
just like inserted wrong battery, it wont ON but not damaged.
but maybe im wrong ;D
As someone who's dealt with SIPs a ton, you'll be fine. In practical terms and through experience assembling boards and changing out LEDs, there is no harm to the board when it comes putting in LEDs the wrong way around, just that it's a major PITA if you SOLDERED them all that way.
Thanks a ton for your help! I guess ill just solder all my switches and flip the LEDs that dont light up :)
:thumb:
dont forget to post the picture when your board is ready
Post by: Ahkrael on Tue, 03 November 2015, 04:58:45
I just received my board, and though I haven't tested it, the other poster earlier said that polarity should be Positive on the Farthest circle from the Resistor. Basically, if you are looking at the Front of the PCB, it would mean Pos is Left, as when you flip it over, the resistors are on the Left, so pos is Right on the reverse side of board. I'm assuming this is the same for the other LEDs as well.
I'm SUPER impressed with the quality of the machining on the alum top. I love how the LED cutouts are done - with the pinholes on top of the dome cuts. I got the angled bottom and it is SOLID. I'm still going to toy around with different spring weights for some of the keys before I solder it together - I only got 60 of the 65g Zealios. I'm thinking of mixing some other springs with Gat linears - 65g Zeals would be roughly equal to what actuation weight? I have some Sprits 78 (2 pcs), 72, 62 and 68 (which are weighted for total compression) and some Gateron springs (massdrop) which are weighted for actuation at 62, 45, and 80 (super heavy). I've got more gat browns if I want more tactiles, but if they are going to be different I might as well do linears, is my thinking.
I'm pretty sure that Zeal weighted his switches using the Korean standard, so the weight should be most similar to the 62g and 68g SPRiT springs you have.
If the Gateton 45g springs are anything like Cherry MX reds, then the bottom out weight should be 60g.
Yeah, I realize that. I've got a little numpad that is PCB mounted, so I'm going to play around with that mixing these extra gaterons in. It's just hard to use a single switch tester to get a feel for what you want, especially when mixing things around. When I used my tester before, I prefered linears with O rings to dampen the landing - though I'm not sure how well those would feel in a board. I used O rings with my Browns for a month or so, and ended up hating it in the end. That's something easy to test and change, but finding a good mix of spring weight with or without the O rings, might be harder. Maybe this is why people usually don't mix different switches often on board, haha. Try to make it perfect, and then it becomes a mess in the end.
Post by: blighty on Tue, 03 November 2015, 17:02:45
[attach=1]
I made myself LOL over the light bleed on the caps lock key. :p
I do have to take off the bottom and resolder the LED under the Print Screen key (cold solder joint...), but not bad for a rush job I guess.
Post by: Steezus on Tue, 03 November 2015, 17:06:38
Potato pic:
(Attachment Link)
I made myself LOL over the light bleed on the caps lock key. :p
I do have to take off the bottom and resolder the LED under the Print Screen key (cold solder joint...), but not bad for a rush job I guess.
Nice job, did you not sip socket your switches? They are a pain in the ass but it's so worth it when an LED burns out or you change the LEDs to match a set. Also what time of button is your Orion v2, black aluminum?
Post by: ramnes on Tue, 03 November 2015, 17:24:11
Potato pic:
(Attachment Link)
I made myself LOL over the light bleed on the caps lock key. :p
I do have to take off the bottom and resolder the LED under the Print Screen key (cold solder joint...), but not bad for a rush job I guess.
Why do you post a picture of almost the build I've planned to do while I didn't receive the board yet? >:D
Post by: blighty on Tue, 03 November 2015, 17:32:32
Nice job, did you not sip socket your switches? They are a pain in the ass but it's so worth it when an LED burns out or you change the LEDs to match a set. Also what time of button is your Orion v2, black aluminum?No sip sockets. I have no plan to change the LED colors. I set the base color to red as well, but haven't quite figured out how to stop the base lights from "breathing." Probably set with controls I didn't flash... The base is the acrylic wedge, not the aluminum one. I wanted a different angle than the LSv2. It's such a solid build, even with the acrylic. I was a bit wary about acrylic bottoms after building the RSIII (kind of flimsy, even with the plate), but the Orion V2 is rock solid. Glad I got in on the buy, and glad I didn't puss out and sell my spot. It's definitely a keeper.
Why do you post a picture of almost the build I've planned to do while I didn't receive the board yet? >:D
Sorry! Great minds think alike? It looks kind of classy and reserved, even with the backlighting. :thumb:
Post by: Steezus on Tue, 03 November 2015, 17:46:27
Nice job, did you not sip socket your switches? They are a pain in the ass but it's so worth it when an LED burns out or you change the LEDs to match a set. Also what time of button is your Orion v2, black aluminum?No sip sockets. I have no plan to change the LED colors. I set the base color to red as well, but haven't quite figured out how to stop the base lights from "breathing." Probably set with controls I didn't flash... The base is the acrylic wedge, not the aluminum one. I wanted a different angle than the LSv2. It's such a solid build, even with the acrylic. I was a bit wary about acrylic bottoms after building the RSIII (kind of flimsy, even with the plate), but the Orion V2 is rock solid. Glad I got in on the buy, and glad I didn't puss out and sell my spot. It's definitely a keeper.
Glad to hear how solid it feels, I do like the acrylic of the RS96 but it does feel a little flimsy. I should be getting an acrylic angled bottom and a aluminum bottom, I'll probably end up using the alu bottom. I love the the acrylic slits when using both the aluminum top and bottom.
Post by: elton5354 on Tue, 03 November 2015, 17:49:47
Nice job, did you not sip socket your switches? They are a pain in the ass but it's so worth it when an LED burns out or you change the LEDs to match a set. Also what time of button is your Orion v2, black aluminum?No sip sockets. I have no plan to change the LED colors. I set the base color to red as well, but haven't quite figured out how to stop the base lights from "breathing." Probably set with controls I didn't flash... The base is the acrylic wedge, not the aluminum one. I wanted a different angle than the LSv2. It's such a solid build, even with the acrylic. I was a bit wary about acrylic bottoms after building the RSIII (kind of flimsy, even with the plate), but the Orion V2 is rock solid. Glad I got in on the buy, and glad I didn't puss out and sell my spot. It's definitely a keeper.
Glad to hear how solid it feels, I do like the acrylic of the RS96 but it does feel a little flimsy. I should be getting an acrylic angled bottom and a aluminum bottom, I'll probably end up using the alu bottom. I love the the acrylic slits when using both the aluminum top and bottom.
I don't see you on my order list though? :P
Mine should be in my hands tomorrow. I'll post an unboxing or something :D
Post by: Steezus on Tue, 03 November 2015, 18:01:23
Nice job, did you not sip socket your switches? They are a pain in the ass but it's so worth it when an LED burns out or you change the LEDs to match a set. Also what time of button is your Orion v2, black aluminum?No sip sockets. I have no plan to change the LED colors. I set the base color to red as well, but haven't quite figured out how to stop the base lights from "breathing." Probably set with controls I didn't flash... The base is the acrylic wedge, not the aluminum one. I wanted a different angle than the LSv2. It's such a solid build, even with the acrylic. I was a bit wary about acrylic bottoms after building the RSIII (kind of flimsy, even with the plate), but the Orion V2 is rock solid. Glad I got in on the buy, and glad I didn't puss out and sell my spot. It's definitely a keeper.
Glad to hear how solid it feels, I do like the acrylic of the RS96 but it does feel a little flimsy. I should be getting an acrylic angled bottom and a aluminum bottom, I'll probably end up using the alu bottom. I love the the acrylic slits when using both the aluminum top and bottom.
I don't see you on my order list though? :P
Mine should be in my hands tomorrow. I'll post an unboxing or something :D
Oh haha I am buying it off another member, being shipped to him first to inspect everything.
Post by: Rainbow_ on Wed, 04 November 2015, 06:55:59
Post by: filphil on Wed, 04 November 2015, 07:02:49
tfw one of those pink slips is in your door :'(
I feel you there, bud. Sit there all day and you have to wonder if they even bothered to ring your doorbell. -_-
Post by: ramnes on Wed, 04 November 2015, 12:36:48
The top housing is really lighter than I thought, so I'm very glad that I choose to pay a bit more to have the alu bottom. Looks really great overall.
Elton, sorry about that Paypal thing, but I was really worried. In the end everything is okay so thanks a lot!
Do you know if we could order some acrylic inserts to put under the holes?
Post by: jaemzp on Wed, 04 November 2015, 15:08:50
Does anyone happen know where to get the program to, well program it?
Post by: slushi on Wed, 04 November 2015, 15:11:05
Thanks elton, got mine yesterday and I've just finished assembling it!
Does anyone happen know where to get the program to, well program it?
Should be here:
EDIT:
Sorry it is here: http://duck0113.tistory.com/m/post/124
Post by: rainb1ood on Wed, 04 November 2015, 15:13:33
http://duck0113.tistory.com/m/post/124
Post by: jaemzp on Wed, 04 November 2015, 17:14:24
Thanks elton, got mine yesterday and I've just finished assembling it!
Does anyone happen know where to get the program to, well program it?
Should be here:http://duck0113.tistory.com/m/post/84
EDIT:
Sorry it is here: http://duck0113.tistory.com/m/post/124
The newer version for Orion v2 is here
http://duck0113.tistory.com/m/post/124
Thanks guys, really appreciate it! Assumed it would have been in the OP and never bothered researching it :))
Post by: rainb1ood on Wed, 04 November 2015, 20:29:56
Thanks elton, got mine yesterday and I've just finished assembling it!
Does anyone happen know where to get the program to, well program it?
Should be here:http://duck0113.tistory.com/m/post/84
EDIT:
Sorry it is here: http://duck0113.tistory.com/m/post/124The newer version for Orion v2 is here
http://duck0113.tistory.com/m/post/124
Thanks guys, really appreciate it! Assumed it would have been in the OP and never bothered researching it :))
Nope it was just posted yesterday on his site (duck)
I got my kit yesterday and its on its way to E3E for assembly.
Some pics I took before I packed it up again
(http://i.imgur.com/bGaolqb.jpg)
(http://i.imgur.com/KRPyMnm.jpg)
(http://i.imgur.com/kl2CV25.jpg)
Love the quality of the aluminum top
Post by: ika on Wed, 04 November 2015, 20:31:50
For that matter, do the steel/alu plates support it? I was under the impression that they do but now I'm second-guessing myself.
EDIT: none of them do T_T
Post by: rainb1ood on Wed, 04 November 2015, 20:36:56
Post by: Steezus on Wed, 04 November 2015, 20:43:58
Does that plastic plate support switch top removal? I don't see the required notches.
For that matter, do the steel/alu plates support it? I was under the impression that they do but now I'm second-guessing myself.
It appears that non of them do :(.
(http://kbdlab.co.kr/files/attach/images/340/979/493/002/c428d19cca751c7b0e185d67d448bc41.jpg)
Post by: Rainbow_ on Wed, 04 November 2015, 20:47:39
WOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
Post by: Dreamre on Wed, 04 November 2015, 21:29:00
Just received the package. I love that "Made in Korea" sticker!
The top housing is really lighter than I thought, so I'm very glad that I choose to pay a bit more to have the alu bottom. Looks really great overall.
Elton, sorry about that Paypal thing, but I was really worried. In the end everything is okay so thanks a lot!
Do you know if we could order some acrylic inserts to put under the holes?
Never doubt Sir Elton! :thumb:
Post by: elton5354 on Wed, 04 November 2015, 22:07:08
(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)
(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)
(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
Post by: gadzkun on Wed, 04 November 2015, 22:17:44
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
dem so fukin gud! :p :thumb:
any news when next GB duck board. :rolleyes:
i really want one.
cant wait for next GB.
Post by: alienman82 on Wed, 04 November 2015, 22:22:43
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
OOOOO!!! ALPS!!
Post by: R1N3 on Wed, 04 November 2015, 22:57:21
One more month seems like nothing for a lifetime of clackiness
Post by: E3E on Wed, 04 November 2015, 23:54:16
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
The angled acrylic bottom makes this keyboard one of the most unique looking I have seen.
I definitely hope that the Octagon v2 has such an option too. I'll be buying all of the bottom case options for that one. :thumb:
Post by: ccc24 on Thu, 05 November 2015, 00:11:35
Post by: appleonama on Thu, 05 November 2015, 04:14:17
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
so freaking awesome no way i could sell mine
well RIP my topre collection gotta make way for 1 cherry board
Post by: E3E on Thu, 05 November 2015, 05:19:26
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
so freaking awesome no way i could sell mine
well RIP my topre collection gotta make way for 1 cherry board
Ahaha. I like your renewed vigor! I know how it is to be torn on a buy, man. Good luck battling those demons, hehe.
Post by: Fnzzy on Thu, 05 November 2015, 10:23:25
Post by: appleonama on Thu, 05 November 2015, 12:01:00
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
so freaking awesome no way i could sell mine
well RIP my topre collection gotta make way for 1 cherry board
Ahaha. I like your renewed vigor! I know how it is to be torn on a buy, man. Good luck battling those demons, hehe.
Lol yes it's a real battle I am so torn at the moment. I love topre and my topre collection but the reality is I only use 2 topre boards out of my 5. I can't have money laying around being unused. I might as well sell them to someone who will use them. This will leave me with my favorite topre boards and awesome cherry board.
Post by: E3E on Thu, 05 November 2015, 12:03:26
Some shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
so freaking awesome no way i could sell mine
well RIP my topre collection gotta make way for 1 cherry board
Ahaha. I like your renewed vigor! I know how it is to be torn on a buy, man. Good luck battling those demons, hehe.
Lol yes it's a real battle I am so torn at the moment. I love topre and my topre collection but the reality is I only use 2 topre boards out of my 5. I can't have money laying around being unused. I might as well sell them to someone who will use them. This will leave me with my favorite topre boards and awesome cherry board.
That's definitely good logic to follow. It can definitely be hard to let go to boards sometimes, even if you don't use them often. Oh the sentimental attachment!
Post by: kacase on Thu, 05 November 2015, 15:15:49
Does anyone know which Function Layers correspond to which keys?
Post by: appleonama on Thu, 05 November 2015, 19:54:46
Post by: Steezus on Thu, 05 November 2015, 19:57:46
All of you post pictures please show off your glories boards.
Agreed, this threads needs more pictures. I want to see some built Orions in all of their shining glory. :p
Post by: elton5354 on Fri, 06 November 2015, 00:26:21
Post by: R1N3 on Fri, 06 November 2015, 00:52:25
Ran out of solder..... >:D
LOL life is pain..
Need those Amazon drones on call for one hour delivery (or it's free)
Post by: kacase on Fri, 06 November 2015, 01:40:31
Sadly I only noticed afterwards that two of my ergo clears were sticky. At least it's just F4 and ' but I think I'll desolder them and check what seems to be the issue.
Also I am still not sure about the O2D mapper. I managed to get it running (hold backspace on orion before plugging in) and also installing the required drivers and software and have successfully uploaded a firmware update to my baby. I'm still having trouble understanding the Funktion layers though. Which keys do I need to press to get to which of the function layers, so I can switch to a different layer or change the led settings.
Post by: jaemzp on Fri, 06 November 2015, 02:44:23
All of you post pictures please show off your glories boards.
You may have one potato ;). 65g zealios + 72g spring in zealio for spacebar
Does anyone happen to know if anyone still sells sip sockets that have not been removed from their plastic housing? I remember zeal selling them but I may be mistaken.
Post by: kacase on Fri, 06 November 2015, 02:50:49
All of you post pictures please show off your glories boards.
You may have one potato ;). 65g zealios + 72g spring in zealio for spacebar
Does anyone happen to know if anyone still sells sip sockets that have not been removed from their plastic housing? I remember zeal selling them but I may be mistaken.
Just get them on Ebay. Free shipping from Thailand to you.
http://www.ebay.com.au/itm/5-x-40-Pin-DIP-SIP-IC-Sockets-Adaptor-Solder-Type-FREE-SHIPPING-/260551794155?hash=item3caa18ddeb:g:9L4AAOxy4RpRzERk
Post by: ika on Fri, 06 November 2015, 09:43:53
All of you post pictures please show off your glories boards.
You may have one potato ;). 65g zealios + 72g spring in zealio for spacebar
Does anyone happen to know if anyone still sells sip sockets that have not been removed from their plastic housing? I remember zeal selling them but I may be mistaken.
Just get them on Ebay. Free shipping from Thailand to you.
http://www.ebay.com.au/itm/5-x-40-Pin-DIP-SIP-IC-Sockets-Adaptor-Solder-Type-FREE-SHIPPING-/260551794155?hash=item3caa18ddeb:g:9L4AAOxy4RpRzERk
The ones on eBay are short and don't protrude through the LED holes in my experience. Sethk recently ran a group buy for Mill-Max sockets from Mouser, those are the ones you're looking for. A good deal pricier than the eBay sockets, but for good reason.
Post by: E3E on Fri, 06 November 2015, 09:53:27
All of you post pictures please show off your glories boards.
You may have one potato ;). 65g zealios + 72g spring in zealio for spacebar
Does anyone happen to know if anyone still sells sip sockets that have not been removed from their plastic housing? I remember zeal selling them but I may be mistaken.
Just get them on Ebay. Free shipping from Thailand to you.
http://www.ebay.com.au/itm/5-x-40-Pin-DIP-SIP-IC-Sockets-Adaptor-Solder-Type-FREE-SHIPPING-/260551794155?hash=item3caa18ddeb:g:9L4AAOxy4RpRzERk
The ones on eBay are short and don't protrude through the LED holes in my experience. Sethk recently ran a group buy for Mill-Max sockets from Mouser, those are the ones you're looking for. A good deal pricier than the eBay sockets, but for good reason.
I recently bought (and subsequently sold) some 13-14mm tail SIP sockets from Jameco. Cheaper than Zeal's 5mm tail sockets and more than twice as long for that added sense of security. http://www.jameco.com/webapp/wcs/stores/servlet/StoreCatalogDrillDownView?langId=-1&storeId=10001&catalogId=10001&freeText=SIPP&search_type=jamecoall
The first on that list should be what I had. Still expensive, especially for anything larger than a 60%. There are tons of other options to choose from as well, and shipping is incredibly fast if you're in the US.
Post by: E3E on Fri, 06 November 2015, 09:59:11
Ran out of solder..... >:D
I've had this happen right while finishing up a restoration on my Fame board with blue alps.
I was so eager to get it done, I used tiny dabs of ChipQuik to finish the job, which worked, but which is very expensive and very useful for tough and stubborn desolder jobs. After that, I bought a huge spool of lead-free stuff and gave my old little spool the finger.
Post by: ccc24 on Fri, 06 November 2015, 10:51:46
Post by: MarkRobbo on Fri, 06 November 2015, 10:59:26
where did you all source your stabs?
I got mine from GON, but spirit sells them too (and gold plated wire)
Post by: sncbraxsc2 on Fri, 06 November 2015, 11:02:49
where did you all source your stabs?
Got mine from GON http://www.gonskeyboardworks.com/ (http://www.gonskeyboardworks.com/)
but saw icyskyz was selling some on reddit https://www.reddit.com/r/mechmarket/comments/3rr1yb/tw_h_stabilizer_wires_blue_sleeved_mini_usb_cable/ (https://www.reddit.com/r/mechmarket/comments/3rr1yb/tw_h_stabilizer_wires_blue_sleeved_mini_usb_cable/)
Post by: Steezus on Fri, 06 November 2015, 11:10:46
where did you all source your stabs?
Got mine from GON http://www.gonskeyboardworks.com/ (http://www.gonskeyboardworks.com/)
but saw icyskyz was selling some on reddit https://www.reddit.com/r/mechmarket/comments/3rr1yb/tw_h_stabilizer_wires_blue_sleeved_mini_usb_cable/ (https://www.reddit.com/r/mechmarket/comments/3rr1yb/tw_h_stabilizer_wires_blue_sleeved_mini_usb_cable/)
I bought two sets of gold stabs from icyskyz, haven't got them in yet but the transaction was easy and had no problems. They don't have to be gold stabs but I like them to be. :p
Post by: appleonama on Fri, 06 November 2015, 11:11:59
:thumb: Well, I'll find love in the Orion but I'm a little skeptical since the duck Eagle wasn't great. Maybe it was the switches, 62g ergo clears felt very cheap to me compared to topre. I recently tried my blacks and they felt awesome for linears. I will be using gateron blacks withSome shots before I build it over the weekend. :)Show Image(http://images.tapatalk-cdn.com/15/11/04/dc304bb833f3c4533619f5c905571f69.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/d28375b349d0f73ff0f571c14c70b953.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/04/26119937f2c84efa1a1431c32aa3469b.jpg)
so freaking awesome no way i could sell mine
well RIP my topre collection gotta make way for 1 cherry board
Ahaha. I like your renewed vigor! I know how it is to be torn on a buy, man. Good luck battling those demons, hehe.
Lol yes it's a real battle I am so torn at the moment. I love topre and my topre collection but the reality is I only use 2 topre boards out of my 5. I can't have money laying around being unused. I might as well sell them to someone who will use them. This will leave me with my favorite topre boards and awesome cherry board.
That's definitely good logic to follow. It can definitely be hard to let go to boards sometimes, even if you don't use them often. Oh the sentimental attachment!
:thumb: Well, I'll find love in the Orion but I'm a little skeptical since the duck Eagle wasn't great. Maybe it was the switches, 62g ergo clears felt very cheap to me compared to topre. I recently tried my blacks and they felt awesome for linears. I will be using gateron blacks with gold plated springs and zip sockets.
Post by: appleonama on Fri, 06 November 2015, 11:17:51
All of you post pictures please show off your glories boards.
You may have one potato ;). 65g zealios + 72g spring in zealio for spacebar
Does anyone happen to know if anyone still sells sip sockets that have not been removed from their plastic housing? I remember zeal selling them but I may be mistaken.
Your best bet is to buy them on eBay along with some very small wore clippers to clip off the black plastic around them.
Post by: appleonama on Fri, 06 November 2015, 11:19:22
where did you all source your stabs?
Sprit aka sprite guy
I bought springs, stabs, and lube ;) from him it took about a week for shipping in the USA
Post by: Steezus on Fri, 06 November 2015, 11:22:00
where did you all source your stabs?
Sprit aka sprite guy
I bought springs, stabs, and lube ;) from him it took about a week for shipping in the USA
Sprit has gone off the deep end again, he's vanished but has slowly been filling out orders. Last I saw somebody that put in an order in the beginning of August got theirs mid October. Just be wary, :thumb:
Post by: appleonama on Fri, 06 November 2015, 11:28:38
Welp then everyone should take this advice. I remember he disappeared when he was fulfilling cases.where did you all source your stabs?
Sprit aka sprite guy
I bought springs, stabs, and lube ;) from him it took about a week for shipping in the USA
Sprit has gone off the deep end again, he's vanished but has slowly been filling out orders. Last I saw somebody that put in an order in the beginning of August got theirs mid October. Just be wary, :thumb:
I bought my stuff earlier this year when he was very active.
Post by: kacase on Fri, 06 November 2015, 11:32:41
(http://i.imgur.com/wtgdtvg.jpg)
(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
Post by: E3E on Fri, 06 November 2015, 11:35:40
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
I love the look of clears with clear switch tops. I think your Orion and my Lightpad could be siblings. :P
(http://i.imgur.com/kMu2jKn.jpg)
Great looking board though! Sorry to derail the thread.
Holy ****, that side LED acrylic panel is god-like! Definitely hope the next Octagon comes with all of the same aesthetics! SO HYPE.
Post by: Pemdas on Fri, 06 November 2015, 11:39:23
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
Yes! That gif is glorious!. The inserts look awesome :thumb:
Post by: Steezus on Fri, 06 November 2015, 11:41:02
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
Great build kacase! I saw your post on reddit and lol'd a little bit by how ignorant the people were commenting on your Orion. They had absolutely no clue what the board was, why it costs so much, and why it did not have any windows keys. :p
Post by: appleonama on Fri, 06 November 2015, 12:07:02
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
:eek: dam
Post by: rainb1ood on Fri, 06 November 2015, 12:07:53
Post by: appleonama on Fri, 06 November 2015, 12:25:10
I should've went blue grey and black looks awesomeJust received mine, safe and sound. It's in perfect condition and I'm gonna assemble it right away.
Will post pics after assembling.
Thanks Elton for the perfect work. :thumb:
PICTURES PICTURES!!!Show Image(http://ww1.sinaimg.cn/mw690/54b7b013gw1exmpfvc6f6j24802tcx6s.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpfir206j24802tcqv7.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpesw73gj24802tcu10.jpg)Show Image(http://ww3.sinaimg.cn/mw690/54b7b013gw1exmpczmgojj24802tc1l1.jpg)Show Image(http://ww4.sinaimg.cn/mw690/54b7b013gw1exmpcnd80qj24802tc7wk.jpg)
For original sized pictures and more you can check: (click 查看大图)
http://photo.weibo.com/1421324307/albums/detail/album_id/3904765762372638#!/mode/1/page/1
The blue-grey + silver case is from Elton. The full black case is ordered from another source.
Post by: E3E on Fri, 06 November 2015, 12:44:43
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
Great build kacase! I saw your post on reddit and lol'd a little bit by how ignorant the people were commenting on your Orion. They had absolutely no clue what the board was, why it costs so much, and why it did not have any windows keys. :p
The reddit MK community is a nice place. Can't blame them for not being elitist enthusiasts. :P It's pretty much the first place a person goes to get their feet wet in this hobby.
Post by: Fnzzy on Fri, 06 November 2015, 13:12:20
Post by: kacase on Fri, 06 November 2015, 13:15:29
I am really happy with my board. I hope there will be a another GB for the Lightpad, or a Lightpad V2 so i can put it on the right side of my mouse :)
Post by: Steezus on Fri, 06 November 2015, 13:16:27
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
Great build kacase! I saw your post on reddit and lol'd a little bit by how ignorant the people were commenting on your Orion. They had absolutely no clue what the board was, why it costs so much, and why it did not have any windows keys. :p
The reddit MK community is a nice place. Can't blame them for not being elitist enthusiasts. :P It's pretty much the first place a person goes to get their feet wet in this hobby.
Yeah I know, by no means was I trying to talk bad about r/MK. I'm not a fan though, I don't see people there appreciate keyboards as much as Geekhack if I'm honest. I spent about 10 hours prepping, building, and keymapping my RS96 and post it on reddit to get about 20 upvotes and then have somebody post there unicorn puke Pok3r and it his the front page of r/MK. I honestly don't really care about upvotes, never did but it's the fact that Pok3r with random ass keycaps than an a custom keyboard, an Orion, an RS96, etc.
Post by: Steezus on Fri, 06 November 2015, 13:17:48
Apologies if I am going sort of off-topic with this, but can someone who used SIP sockets for LEDs tell me if it was worth it? I am currently removing SIP sockets from their housing for my Orion and it's super annoying :D
Sip Sockets are so worth in my opinion, it's a pain at first but worth it in the end. It's nice when you have a faulty LED die and then it just becomes and easy swap, or if you change your keyset and want new matching LEDs to go along with it then it's much easier to swap the LEDs than de-soldering and soldering new LEDs.
Post by: Fnzzy on Fri, 06 November 2015, 13:20:15
Apologies if I am going sort of off-topic with this, but can someone who used SIP sockets for LEDs tell me if it was worth it? I am currently removing SIP sockets from their housing for my Orion and it's super annoying :D
Sip Sockets are so worth in my opinion, it's a pain at first but worth it in the end. It's nice when you have a faulty LED die and then it just becomes and easy swap, or if you change your keyset and want new matching LEDs to go along with it then it's much easier to swap the LEDs than de-soldering and soldering new LEDs.
Alright, sounds like I will continue. Seems to be really worth it afterall :D
Post by: kacase on Fri, 06 November 2015, 13:37:53
Apologies if I am going sort of off-topic with this, but can someone who used SIP sockets for LEDs tell me if it was worth it? I am currently removing SIP sockets from their housing for my Orion and it's super annoying :D
Sip Sockets are so worth in my opinion, it's a pain at first but worth it in the end. It's nice when you have a faulty LED die and then it just becomes and easy swap, or if you change your keyset and want new matching LEDs to go along with it then it's much easier to swap the LEDs than de-soldering and soldering new LEDs.
Alright, sounds like I will continue. Seems to be really worth it afterall :D
With my method it's actually not that much of a pain http://imgur.com/a/null/titledesc
Post by: Steezus on Fri, 06 November 2015, 13:44:53
Apologies if I am going sort of off-topic with this, but can someone who used SIP sockets for LEDs tell me if it was worth it? I am currently removing SIP sockets from their housing for my Orion and it's super annoying :D
Sip Sockets are so worth in my opinion, it's a pain at first but worth it in the end. It's nice when you have a faulty LED die and then it just becomes and easy swap, or if you change your keyset and want new matching LEDs to go along with it then it's much easier to swap the LEDs than de-soldering and soldering new LEDs.
FYI the link isn't working for me.
Alright, sounds like I will continue. Seems to be really worth it afterall :D
With my method it's actually not that much of a pain http://imgur.com/a/null/titledesc
Post by: missalaire on Fri, 06 November 2015, 15:35:17
Post by: slushi on Fri, 06 November 2015, 18:21:17
Post by: sncbraxsc2 on Fri, 06 November 2015, 18:28:38
Just out of curiosity does anyone happen to have a flat acrylic bottom they'd be willing to sell?
I have a flat acrylic bottom that I would like to trade. Its my only bottom :-[
Post by: missalaire on Fri, 06 November 2015, 20:54:49
Just out of curiosity does anyone happen to have a flat acrylic bottom they'd be willing to sell?
I have a flat acrylic bottom that I would like to trade. Its my only bottom :-[
I have a black aluminum bottom, but unfortunately not looking to sell or trade it :/
I just want a flat acrylic bottom that I can swap out to if I fancy.
Post by: ika on Fri, 06 November 2015, 20:55:08
Apologies if I am going sort of off-topic with this, but can someone who used SIP sockets for LEDs tell me if it was worth it? I am currently removing SIP sockets from their housing for my Orion and it's super annoying :D
Sip Sockets are so worth in my opinion, it's a pain at first but worth it in the end. It's nice when you have a faulty LED die and then it just becomes and easy swap, or if you change your keyset and want new matching LEDs to go along with it then it's much easier to swap the LEDs than de-soldering and soldering new LEDs.
Alright, sounds like I will continue. Seems to be really worth it afterall :D
With my method it's actually not that much of a pain http://imgur.com/a/null/titledesc (http://imgur.com/a/null/titledesc)
pls fix your link! is your method shaving the plastic housings?
Post by: elton5354 on Fri, 06 November 2015, 21:20:43
(http://images.tapatalk-cdn.com/15/11/06/93addb4106a9b540e9b1ad9994df9257.jpg)
(http://images.tapatalk-cdn.com/15/11/06/8dd778e0589ef572b7e6b2768f5d0dbd.jpg)
Post by: alienman82 on Fri, 06 November 2015, 22:50:16
Just some photos..Show Image(http://images.tapatalk-cdn.com/15/11/06/93addb4106a9b540e9b1ad9994df9257.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/06/8dd778e0589ef572b7e6b2768f5d0dbd.jpg)
which alps caps?
Post by: E3E on Sat, 07 November 2015, 08:47:25
Here are some pics of my assembled goodness:Show Image(http://i.imgur.com/wtgdtvg.jpg)Show Image(http://i.imgur.com/4qz5TiY.gif)
(http://i.imgur.com/d8A8mpL.jpg) (http://imgur.com/d8A8mpL)
Great build kacase! I saw your post on reddit and lol'd a little bit by how ignorant the people were commenting on your Orion. They had absolutely no clue what the board was, why it costs so much, and why it did not have any windows keys. :p
The reddit MK community is a nice place. Can't blame them for not being elitist enthusiasts. :P It's pretty much the first place a person goes to get their feet wet in this hobby.
Yeah I know, by no means was I trying to talk bad about r/MK. I'm not a fan though, I don't see people there appreciate keyboards as much as Geekhack if I'm honest. I spent about 10 hours prepping, building, and keymapping my RS96 and post it on reddit to get about 20 upvotes and then have somebody post there unicorn puke Pok3r and it his the front page of r/MK. I honestly don't really care about upvotes, never did but it's the fact that Pok3r with random ass keycaps than an a custom keyboard, an Orion, an RS96, etc.
Heh. It's subjective, imo, but to be honest, I've had my builds and things I have labored on for days seemingly ignored on GeekHack too, probably because I have a **** camera or something. So I really don't know what to say there. I often feel overlooked, but that's likely a stupid inferiority complex I've developed. That's neither here nor there. My Octagon and Lightpad w/ Jukebox got some pretty nice karma, but yeah. Er, though that GIF of kacase's Orion's RGB lighting got pretty popular.
It depends really. I don't think they are always as smitten by customs as we are. In that respect, I do agree to an extent. I'm generally not a fan of commercial boards these days and could care less about Pok3rs and the like. There's no appeal there for me compared to custom builds and projects.
Post by: Fnzzy on Sat, 07 November 2015, 14:49:01
Anyway back to the point, anyone had similar problems where the 4 corner screws wouldn't go all the way down?
Post by: filphil on Sat, 07 November 2015, 15:27:07
Just assembled mine and I have some problems with the screws. I have the flat acryllic backplate and the 4 long screws that you are supposed to screw in the corner won't go all the way down. At some point they just won't go further down and unfortunately I learned that the hard way and one of my screws just broke off after I tried tried to tighten it even more in an attempt to make it go all the way down. Now I have half of a screw stuck in my top housing. However the 4 small screws worked just fine. My plan is to get similar screws that I can screw into the 3 corners that I have left and just leave that one corner screw alone and treat it as a cosmetic defect.
Anyway back to the point, anyone had similar problems where the 4 corner screws wouldn't go all the way down?
I looked and it seems like duck didn't include enough screws for the flat acrylic plate. The case screws given to me were all four long and four short which is fine for the other two bottom cases. Flat bottom needs 8 short.
Post by: Fnzzy on Sat, 07 November 2015, 15:44:38
Post by: digi on Sat, 07 November 2015, 15:56:33
Post by: filphil on Sat, 07 November 2015, 16:18:53
This is why I was confused, the screw count seemed exactly right. Well I ****ed up. Gotta get more flat screws now and later see how to remove the broken one...
You can use a manual screw extractor set. They're pretty inexpensive from home depot/lowes type stores and a good thing to have around the house. Just make sure you start with the smallest size and work your way up if need be.
Post by: Fnzzy on Sat, 07 November 2015, 17:57:28
Post by: E3E on Sat, 07 November 2015, 18:06:12
Will trade a Clack for an unbuilt kit, pm for details.
:rolleyes:
Post by: elton5354 on Sat, 07 November 2015, 20:06:33
Just assembled mine and I have some problems with the screws. I have the flat acryllic backplate and the 4 long screws that you are supposed to screw in the corner won't go all the way down. At some point they just won't go further down and unfortunately I learned that the hard way and one of my screws just broke off after I tried tried to tighten it even more in an attempt to make it go all the way down. Now I have half of a screw stuck in my top housing. However the 4 small screws worked just fine. My plan is to get similar screws that I can screw into the 3 corners that I have left and just leave that one corner screw alone and treat it as a cosmetic defect.
Anyway back to the point, anyone had similar problems where the 4 corner screws wouldn't go all the way down?
Just assembled mine and I have some problems with the screws. I have the flat acryllic backplate and the 4 long screws that you are supposed to screw in the corner won't go all the way down. At some point they just won't go further down and unfortunately I learned that the hard way and one of my screws just broke off after I tried tried to tighten it even more in an attempt to make it go all the way down. Now I have half of a screw stuck in my top housing. However the 4 small screws worked just fine. My plan is to get similar screws that I can screw into the 3 corners that I have left and just leave that one corner screw alone and treat it as a cosmetic defect.
Anyway back to the point, anyone had similar problems where the 4 corner screws wouldn't go all the way down?
I looked and it seems like duck didn't include enough screws for the flat acrylic plate. The case screws given to me were all four long and four short which is fine for the other two bottom cases. Flat bottom needs 8 short.
Wow, I'm definitely going to address this back to truecustom. :-[
Post by: Fnzzy on Sun, 08 November 2015, 10:51:24
(http://i.imgur.com/tRRHEqx.jpg)
(http://i.imgur.com/6kFrJFd.jpg)
(http://i.imgur.com/l6wRcb4.jpg)
(http://i.imgur.com/VwJTgsg.jpg)
(http://i.imgur.com/Nv7pOz4.jpg)
(http://i.imgur.com/jD3xgTS.jpg)
Post by: Want on Sun, 08 November 2015, 10:54:41
Post by: jbondeson on Sun, 08 November 2015, 10:56:31
Just some photos..Show Image(http://images.tapatalk-cdn.com/15/11/06/93addb4106a9b540e9b1ad9994df9257.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/06/8dd778e0589ef572b7e6b2768f5d0dbd.jpg)
I can't believe I didn't investigate this buy thinking it didn't have any Alps support :'(
You just need some Blues in a case that beautiful!
Post by: rainb1ood on Sun, 08 November 2015, 12:32:48
10/10 well done!Show Image(http://i.imgur.com/h8U8siZ.jpg)Show Image(http://i.imgur.com/tRRHEqx.jpg)Show Image(http://i.imgur.com/6kFrJFd.jpg)Show Image(http://i.imgur.com/l6wRcb4.jpg)Show Image(http://i.imgur.com/VwJTgsg.jpg)Show Image(http://i.imgur.com/Nv7pOz4.jpg)Show Image(http://i.imgur.com/jD3xgTS.jpg)
What camera did you use?
Post by: missalaire on Sun, 08 November 2015, 14:11:35
Never did I imagine the flat acrylic to look so good. Nice job mang.
Same, until I saw this: http://kbdlab.co.kr/index.php?document_srl=2381083&mid=board_Lsno50
Makes me really regret not getting the flat acrylic bottom in the first place. Funds were tighter at the start of the group buy, but now I really realize how cheap that option was :/
Someone sell me your flat acrylic bottom!
Post by: Ahkrael on Sun, 08 November 2015, 14:41:31
Post by: slushi on Sun, 08 November 2015, 14:44:57
Post by: Fnzzy on Sun, 08 November 2015, 14:57:20
10/10 well done!
What camera did you use?
Nikon D5200 with a Sigma 50MM F1.4EX.
Thanks!
Post by: R1N3 on Sun, 08 November 2015, 16:13:43
To be fair, I think if someone were to plan on DIY'ing any style of bottom, the clear acrylic wouldn't be the hardest to manage. I mean you could get a piece cut with the right dimensions and rig it up somewhat.Was there another update I missed?
Post by: filphil on Sun, 08 November 2015, 16:17:18
To be fair, I think if someone were to plan on DIY'ing any style of bottom, the clear acrylic wouldn't be the hardest to manage. I mean you could get a piece cut with the right dimensions and rig it up somewhat.Was there another update I missed?
Negative. Jut that the flat acrylic plate was the underdog of the bottom plates but it looks great.
10/10 well done!
What camera did you use?
Nikon D5200 with a Sigma 50MM F1.4EX.
Thanks!
Do you use an ikea table too? It looks like the same grain/pattern and color as mine, :))
Post by: R1N3 on Sun, 08 November 2015, 16:26:59
They all look so good! The exposed pcb gives the flat bottom a completely different sex appeal though.. especially for the price pointTo be fair, I think if someone were to plan on DIY'ing any style of bottom, the clear acrylic wouldn't be the hardest to manage. I mean you could get a piece cut with the right dimensions and rig it up somewhat.Was there another update I missed?
Negative. Jut that the flat acrylic plate was the underdog of the bottom plates but it looks great.10/10 well done!
What camera did you use?
Nikon D5200 with a Sigma 50MM F1.4EX.
Thanks!
Do you use an ikea table too? It looks like the same grain/pattern and color as mine, :))
Post by: Rainbow_ on Sun, 08 November 2015, 16:40:10
Post by: Steezus on Sun, 08 November 2015, 16:42:47
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
I don't believe so, it's just standard procedure for assembling every board. It's also a big help that the all the SMD parts come pre-soldered. If you're having trouble building I suggest you take look some member's build logs, that's how I learned to build my first board. :thumb:
Edit: Oops I think you may mean the case itself and not the board, if so there so there are no instructions listed for that.
Post by: filphil on Sun, 08 November 2015, 16:53:11
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
It's fairly straight forward when you get the board. When I had my flat acrylic plate there weren't enough small screws in a single pack. The packs you get for the bottom housing consist of 4 long screws, 4 small screws, 10 plate screws, and rubber feet. Maybe the second shipment will address this.
Post by: slushi on Sun, 08 November 2015, 16:56:23
Post by: ccc24 on Sun, 08 November 2015, 17:23:41
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
It's fairly straight forward when you get the board. When I had my flat acrylic plate there weren't enough small screws in a single pack. The packs you get for the bottom housing consist of 4 long screws, 4 small screws, 10 plate screws, and rubber feet. Maybe the second shipment will address this.
What about a guide for the firmware?
Post by: Steezus on Sun, 08 November 2015, 17:25:47
Just a quick question as I've been following this thread quite a bit. Am I correct in assuming that there is no ETA for the second set of shipments? Just wondering.
If I'm not mistaken Elton said it should be an additional month after the first 30 are shipped.
Post by: Rainbow_ on Sun, 08 November 2015, 17:32:47
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
I don't believe so, it's just standard procedure for assembling every board. It's also a big help that the all the SMD parts come pre-soldered. If you're having trouble building I suggest you take look some member's build logs, that's how I learned to build my first board. :thumb:
Edit: Oops I think you may mean the case itself and not the board, if so there so there are no instructions listed for that.
lol yeah, I meant the case. I've done SMD soldering before and it's not that bad. I guess I'll look harder at it when I get my switches and stabs.
Post by: alienman82 on Sun, 08 November 2015, 17:33:40
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
I don't believe so, it's just standard procedure for assembling every board. It's also a big help that the all the SMD parts come pre-soldered. If you're having trouble building I suggest you take look some member's build logs, that's how I learned to build my first board. :thumb:
Edit: Oops I think you may mean the case itself and not the board, if so there so there are no instructions listed for that.
lol yeah, I meant the case. I've done SMD soldering before and it's not that bad. I guess I'll look harder at it when I get my switches and stabs.
ooh reminds me I need to pick up lube and led's...
Post by: filphil on Sun, 08 November 2015, 17:52:53
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
It's fairly straight forward when you get the board. When I had my flat acrylic plate there weren't enough small screws in a single pack. The packs you get for the bottom housing consist of 4 long screws, 4 small screws, 10 plate screws, and rubber feet. Maybe the second shipment will address this.
What about a guide for the firmware?
http://duck0113.tistory.com/124
Post by: slushi on Sun, 08 November 2015, 20:02:36
If I'm not mistaken Elton said it should be an additional month after the first 30 are shipped.
Oh I thought that only applied to those who were in the first 30 but didn't get into the original shipment.
Post by: Steezus on Sun, 08 November 2015, 20:11:23
If I'm not mistaken Elton said it should be an additional month after the first 30 are shipped.
Oh I thought that only applied to those who were in the first 30 but didn't get into the original shipment.
The first 30 will be shipped soon. The rest will follow after a few weeks.
Tracking #s are updated for some.. Due to some problems manufacturing the acrylic angled bottom casings, there weren't many available to ship hence the mixed of order in shipping.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
It's about another month for the rest to be ready to ship.
I assumed by "others" he means the rest of the orders but I'm not quite sure. Either way it seems like it's going to be around 3-4 weeks.
Post by: slushi on Sun, 08 November 2015, 20:24:47
Post by: kacase on Mon, 09 November 2015, 03:47:10
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
I don't believe so, it's just standard procedure for assembling every board. It's also a big help that the all the SMD parts come pre-soldered. If you're having trouble building I suggest you take look some member's build logs, that's how I learned to build my first board. :thumb:
Edit: Oops I think you may mean the case itself and not the board, if so there so there are no instructions listed for that.
lol yeah, I meant the case. I've done SMD soldering before and it's not that bad. I guess I'll look harder at it when I get my switches and stabs.
Instructions
Assembly
Except for the Switches and in Switch Leds/SIPs there is no soldering you have to do. The Assembly couldnt be more straight forwards:
1. Install stabs on pcb
2. Solder Switches and LEDs
3. Screw Plate PCB combo onto the top cover with 8 round head screws (put top cover upside down)
4. Put the two acrylic inserts into place (after removing the protective film)
5. Put Top cover into place on top of the bottom one with acrylic inserts inbetween
6. Flip upside down and screw together (4 small flat screws 4 very long cylindrical screws for the angled bottoms, 8 flat screws for the flat acrylic bottom)
7. Turn upside down and you are finished ;)
Firmware
For the firmware its a bit more work..
I got most of the information from this guide:
https://drive.google.com/file/d/0B4Q2mepcAlZnWmx5V1d2QmZqZGs/view
1. Download the follwing files
http://sourceforge.net/projects/dfu-programmer/files/dfu-programmer/0.7.0/
https://gallery.atmel.com/Products/Details/6272a8fd-68fe-43d8-a990-741878cfe7b6 (sadly you will have to register for it >:D)
http://duck0113.tistory.com/124
2. Install the amtel usb driver
3. put the o2d mapper into the folder of the dfu programmer
4. Start up the o2dmapper and map your stuff
5. save your hex and rename it (long names make it crash)
6. disconnect your Orion V2
7. hold backspace and reconnect your v2
8. in the firmware upload popup click connect and upload your firmware
9. you are good to go! have fun with this amazing keyboard
These are not proper official instructions, but rather a sum up of how I assembled my Orion and updated the firmware. Please be careful when handeling your device and don't make me responsible for any damage that occurs.
Post by: MarkRobbo on Mon, 09 November 2015, 04:14:27
Does it come flashed with basic firmware?
Post by: filphil on Mon, 09 November 2015, 05:05:29
Thanks for the write-up
Does it come flashed with basic firmware?
Yep. You should be happily typing after your switches are soldered.
Post by: MarkRobbo on Mon, 09 November 2015, 07:40:39
Thanks for the write-up
Does it come flashed with basic firmware?
Yep. You should be happily typing after your switches are soldered.
Perfect, thanks
Post by: CyriusG on Mon, 09 November 2015, 13:10:01
Post by: nguyenkimtam on Mon, 09 November 2015, 14:17:31
Post by: alienman82 on Mon, 09 November 2015, 14:20:56
waiting for the next 30 :'( :'( :'( :'( :'(
yes patiently
Post by: Steezus on Mon, 09 November 2015, 14:22:21
waiting for the next 30 :'( :'( :'( :'( :'(
yes patiently
Perfection takes time, time that I don't have the patience to wait for. :p
Post by: monotagary on Mon, 09 November 2015, 16:09:54
To the best of my knowledge I have assembled my Orion correctly, and when I plug it in, all the LEDs come online but I can't get it to type. Are there any additional steps to getting the ALPs PCB working?
Post by: elton5354 on Mon, 09 November 2015, 18:38:01
Question for anyone with an ALPs Orion v2!
To the best of my knowledge I have assembled my Orion correctly, and when I plug it in, all the LEDs come online but I can't get it to type. Are there any additional steps to getting the ALPs PCB working?
I got the same problem. I'm waiting on leeku's reply on how to keymap (program) it.
Post by: kacase on Mon, 09 November 2015, 18:56:13
Question for anyone with an ALPs Orion v2!
To the best of my knowledge I have assembled my Orion correctly, and when I plug it in, all the LEDs come online but I can't get it to type. Are there any additional steps to getting the ALPs PCB working?
Sadly I don't have the Alps board but you could try the following.
Disconnect your orion.
Hold Backspace and plug it back in.
The LEDs should not come on this time, and you should be able to flash the firmware.
Maybe tell us at which step it is not going as it should be.
Post by: elton5354 on Mon, 09 November 2015, 19:03:34
Question for anyone with an ALPs Orion v2!
To the best of my knowledge I have assembled my Orion correctly, and when I plug it in, all the LEDs come online but I can't get it to type. Are there any additional steps to getting the ALPs PCB working?
http://kbdlab.co.kr/index.php?document_srl=2702787&mid=board_sw
Here are the instructions.
Post by: blighty on Mon, 09 November 2015, 19:07:17
[attach=1]
I hope everyone gets their build issues sorted quickly so they can enjoy this nice piece of kit.
Post by: E3E on Mon, 09 November 2015, 19:52:24
LEDs fully lit:
(Attachment Link)
I hope everyone gets their build issues sorted quickly so they can enjoy this nice piece of kit.
Looks like a board from the underworld >:D
Post by: appleonama on Mon, 09 November 2015, 20:16:54
tbh I always wanted some unicorn led vomit.
Post by: blighty on Mon, 09 November 2015, 21:03:03
LEDs fully lit:
(Attachment Link)
I hope everyone gets their build issues sorted quickly so they can enjoy this nice piece of kit.
Looks like a board from the underworld >:D
Ha! I'm hoping to raise a little hell in Fallout 4 come midnight on it. :)
Post by: monotagary on Tue, 10 November 2015, 03:10:14
Question for anyone with an ALPs Orion v2!
To the best of my knowledge I have assembled my Orion correctly, and when I plug it in, all the LEDs come online but I can't get it to type. Are there any additional steps to getting the ALPs PCB working?
http://kbdlab.co.kr/index.php?document_srl=2702787&mid=board_sw
Here are the instructions.
Thanks elton, this got it working!
Post by: kacase on Tue, 10 November 2015, 03:20:55
Post by: filphil on Tue, 10 November 2015, 06:44:38
I saw a lot of people on KBDlab having Brass inserts for their Orion V2. Were they not a part of our Version or am I the only one who doesnt have one?
I think those were custom cut. I approached some local shops to have them cut me inserts but they won't do a one off for a small price.
If anyone has access or the facilities to get one cutting done here is the drawing for the insert.
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
Post by: R1N3 on Tue, 10 November 2015, 11:04:51
I saw a lot of people on KBDlab having Brass inserts for their Orion V2. Were they not a part of our Version or am I the only one who doesnt have one?
I think those were custom cut. I approached some local shops to have them cut me inserts but they won't do a one off for a small price.
If anyone has access or the facilities to get one cutting done here is the drawing for the insert.
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
I might have someone. She and I aren't on really good terms atm but I'll talk to her about it. Is solid brass what people want?
Post by: Steezus on Tue, 10 November 2015, 11:23:45
I saw a lot of people on KBDlab having Brass inserts for their Orion V2. Were they not a part of our Version or am I the only one who doesnt have one?
I think those were custom cut. I approached some local shops to have them cut me inserts but they won't do a one off for a small price.
If anyone has access or the facilities to get one cutting done here is the drawing for the insert.
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
I might have someone. She and I aren't on really good terms atm but I'll talk to her about it. Is solid brass what people want?
I'd be interested in solid brass plate, I don't have my board yet so do the cases already have been cutout for a brass plate and just no brass plate was provided?
Edit: Oops messed up quoting. :p
Post by: alienman82 on Tue, 10 November 2015, 11:24:20
I saw a lot of people on KBDlab having Brass inserts for their Orion V2. Were they not a part of our Version or am I the only one who doesnt have one?
I think those were custom cut. I approached some local shops to have them cut me inserts but they won't do a one off for a small price.
If anyone has access or the facilities to get one cutting done here is the drawing for the insert.
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
I might have someone. She and I aren't on really good terms atm but I'll talk to her about it. Is solid brass what people want?
yeah solid the heavier the better kinda thing
Post by: Rainbow_ on Tue, 10 November 2015, 11:26:10
I saw a lot of people on KBDlab having Brass inserts for their Orion V2. Were they not a part of our Version or am I the only one who doesnt have one?
I think those were custom cut. I approached some local shops to have them cut me inserts but they won't do a one off for a small price.
If anyone has access or the facilities to get one cutting done here is the drawing for the insert.
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
I might have someone. She and I aren't on really good terms atm but I'll talk to her about it. Is solid brass what people want?
How much would such a thing run us?
Post by: ramnes on Tue, 10 November 2015, 17:05:30
I also would be interested in some side acrylic inserts, if someone know where/how to get/make them.
Post by: R1N3 on Tue, 10 November 2015, 17:56:16
Post by: kacase on Tue, 10 November 2015, 18:10:35
Post by: alienman82 on Tue, 10 November 2015, 18:14:04
if you guys want, I can also contact a local milling shop. How many of you would be interested in the brass inserts?
is the alu bottom the only one which works with brass? I'm guessing that's the case
Post by: filphil on Tue, 10 November 2015, 18:43:46
Post by: MarkRobbo on Tue, 10 November 2015, 20:06:07
Post by: missalaire on Tue, 10 November 2015, 20:50:20
Interested in brass insert depending on price/shipping.
Same
Post by: Rainbow_ on Tue, 10 November 2015, 23:19:08
if you guys want, I can also contact a local milling shop. How many of you would be interested in the brass inserts?
is the alu bottom the only one which works with brass? I'm guessing that's the case
As far as I'm aware, yes, but I haven't seen the angled acrylic bottom, maybe that one works too...
Post by: Doobalicious on Wed, 11 November 2015, 00:59:57
Post by: Prankk on Wed, 11 November 2015, 07:24:53
Post by: aznairjordan on Wed, 11 November 2015, 08:58:53
Post by: Rainbow_ on Wed, 11 November 2015, 14:09:17
photos
Post by: Steezus on Wed, 11 November 2015, 14:30:39
http://imgur.com/a/BTXEC
photos
Very nice, how come you decided to go without any in-switch LEDs? Usually people like to make sure their Orions can be seen from outer space. :p
Post by: filphil on Wed, 11 November 2015, 15:00:24
http://imgur.com/a/BTXEC
photos
The plastic plate feels great on the hands. Nice Orion!
Post by: Rainbow_ on Wed, 11 November 2015, 15:33:13
Very nice, how come you decided to go without any in-switch LEDs? Usually people like to make sure their Orions can be seen from outer space. :p
lol, I'm not one for in-switch LEDs. never really got into them. maybe I can add some later. I just want to make sure everything's the way I want it, because it's a little harder to get the switches out with LEDs in them.
The plastic plate feels great on the hands. Nice Orion!
yeah, the plastic plate is nice... only complaint being that it was too bendable, it was difficult to get the switches into it.
on an unrelated note, anyone know how I can make all of the 5 LEDs stay lit?
Post by: appleonama on Wed, 11 November 2015, 19:09:00
Post by: Rainbow_ on Wed, 11 November 2015, 19:42:49
I was almost rear ended by a guy texting and driving. I told you guys I have a higher probability of dying than receiving this keyboard. :'(
Reply #1000 though, nice job.
Post by: monotagary on Wed, 11 November 2015, 19:58:38
I was almost rear ended by a guy texting and driving. I told you guys I have a higher probability of dying than receiving this keyboard. :'(
Reply #1000 though, nice job.
Totally worth
Post by: ccc24 on Wed, 11 November 2015, 21:56:37
Post by: filphil on Wed, 11 November 2015, 22:12:41
can anyone explain the difference in feel between the 3 plates? Does the acrylic plate have less of a 'ping'?
If you're familiar with pcb mount or gons polycarbonate plate I would say it reminds me of those. Probably closer to the former actually. I opted for plastic over aluminum and steel for my board.
Post by: missalaire on Wed, 11 November 2015, 22:41:48
Post by: whentheclouds on Wed, 11 November 2015, 22:43:57
Post by: slushi on Wed, 11 November 2015, 22:49:46
does anybody else feel the acrylic angled bottom gives the board a strange and disproportional look?
Kind of, but it gets so shiney.. Me likes shiney.
But seriously, I'd love to get my hands on a black aluminum bottom instead.
Post by: blighty on Thu, 12 November 2015, 00:41:13
does anybody else feel the acrylic angled bottom gives the board a strange and disproportional look?
Kind of, but it gets so shiney.. Me likes shiney.
But seriously, I'd love to get my hands on a black aluminum bottom instead.
I went for the acrylic bottom to have a different degree/angle. I like the aluminum's angle fine (assuming it's the same as the LSv2), but I wanted to try something different. I'm definitely a fan of the angle. I was going to spray black vinyl dye on the base to darken it up, but changed my mind (I figured the base has all those LEDs, so why mask them). I like how the board looks like it's glowing from the inside, showing through both the top and the bottom. It's solid, stable, won't slide around on the desk, and doesn't kill one's back if you pack it along with a laptop. If the upcoming 75% duck board has the same angled acrylic bottom with the same angle, I'd do my damnedest to jump on board that buy.
TL;DR:
I like how my set up looks with red backlighting. :D
Post by: E3E on Thu, 12 November 2015, 01:51:08
does anybody else feel the acrylic angled bottom gives the board a strange and disproportional look?
Not at all! It just looks like an aluminum bottom died and left behind its ghost.
Seriously though, I love that it has the same look as the aluminum angled bottom and the fact it literally gets painted with whatever colors the LEDs are is an amazing aspect. I definitely will have to get one of each option for the next Octagon.
Post by: ika on Thu, 12 November 2015, 02:51:56
does anybody else feel the acrylic angled bottom gives the board a strange and disproportional look?
Opposite for me, I think the full alu bottom looks strangely elongated and too tall. The acrylic bottom is the perfect angle and shape, it's exactly what I imagine a keyboard should be like.
Post by: whentheclouds on Thu, 12 November 2015, 03:20:38
LED/lighting capabilities is ofc, a separate discussion entirely
Post by: E3E on Thu, 12 November 2015, 06:38:45
are you referring to the frontal view when you say it's too tall? if so i definitely agree. but the primary view of a keyboard is from either sides, and to me the full alu bottom look more 'complete' and don't have the tall body/short leg effect that the acry bottom does
LED/lighting capabilities is ofc, a separate discussion entirely
D: I don't think and Duck board looks too tall. That angle is to die for! <3 They look amazing with an angled wrist rest, imo. If you mean primary view for other people, then I suppose I get that, but unless you're reaching your arms over from an offset position in front of the keyboard, your primary view is in front, haha.
Post by: whentheclouds on Thu, 12 November 2015, 08:34:44
fnzzy's photos are the best in this thread so far for me. defo getting the flat acry bottom for the octa v2
Post by: Fnzzy on Thu, 12 November 2015, 11:00:11
fnzzy's photos
I've been summoned!
Added some color
(http://i.imgur.com/bhcoxq2.jpg) (http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...
(http://i.imgur.com/chWHLUs.jpg) (http://i.imgur.com/mNTX85q.jpg)
(http://i.imgur.com/hw9LBCa.jpg) (http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
Post by: Steezus on Thu, 12 November 2015, 11:08:02
fnzzy's photos
I've been summoned!
Added some colorShow Image(http://i.imgur.com/bhcoxq2.jpg)Show Image(http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...Show Image(http://i.imgur.com/chWHLUs.jpg)
more color!Show Image(http://i.imgur.com/mNTX85q.jpg)
good look at the 9° angleShow Image(http://i.imgur.com/hw9LBCa.jpg)
you can see my missing screws in this oneShow Image(http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
Looks amazing, the flat acylic bottom looks so much better than I expected. May have to try and attempt to make one if I ever get some free time.
Post by: rainb1ood on Thu, 12 November 2015, 12:17:02
Post by: alienman82 on Thu, 12 November 2015, 12:23:34
fnzzy's photos
I've been summoned!
Added some colorShow Image(http://i.imgur.com/bhcoxq2.jpg)Show Image(http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...Show Image(http://i.imgur.com/chWHLUs.jpg)Show Image(http://i.imgur.com/mNTX85q.jpg)Show Image(http://i.imgur.com/hw9LBCa.jpg)Show Image(http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
What esc key?
Post by: fliptrik on Thu, 12 November 2015, 12:35:16
fnzzy's photos
I've been summoned!
Added some colorShow Image(http://i.imgur.com/bhcoxq2.jpg)Show Image(http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...Show Image(http://i.imgur.com/chWHLUs.jpg)Show Image(http://i.imgur.com/mNTX85q.jpg)Show Image(http://i.imgur.com/hw9LBCa.jpg)Show Image(http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
Damn, girl. That clear bottom is sexy af.
Post by: appleonama on Thu, 12 November 2015, 13:09:42
Post by: Fnzzy on Thu, 12 November 2015, 13:13:46
What esc key?
I have absolutely no idea. It's a sort of cyan green-ish thick ABS keycap I found on the attic in a little baggie along with some doubleshot f-keys. To this day I couldn't figure out from what keyboard it came from originally. If anyone has any lead that would be cool!
Post by: romevi on Thu, 12 November 2015, 13:18:59
:thumb: here's to a day of not dying
Day's not over yet.
Post by: slushi on Thu, 12 November 2015, 13:21:24
:thumb: here's to a day of not dying
Day's not over yet.
This got dark reallll quick
Post by: alienman82 on Thu, 12 November 2015, 13:22:29
:thumb: here's to a day of not dying
you're the most patient being there ever was
Post by: appleonama on Thu, 12 November 2015, 13:35:28
:thumb: here's to a day of not dying
Day's not over yet.
:thumb: here's to a day of not dying
Day's not over yet.
This got dark reallll quick
:thumb: here's to a day of not dying
you're the most patient being there ever was
:)) who will inherit my keyboards?
Post by: alienman82 on Thu, 12 November 2015, 13:53:08
:thumb: here's to a day of not dying
Day's not over yet.:thumb: here's to a day of not dying
Day's not over yet.
This got dark reallll quick:thumb: here's to a day of not dying
you're the most patient being there ever was
:)) who will inherit my keyboards?
dumpster?
Post by: slushi on Thu, 12 November 2015, 13:56:50
dumpster?:p
Post by: ramnes on Thu, 12 November 2015, 19:44:48
Post by: Dreamre on Thu, 12 November 2015, 19:52:32
Elton, are you going to sell some acrylic inserts for the v2? :confused:
I don't think has ever sold any inserts... :(
Post by: ramnes on Thu, 12 November 2015, 20:01:10
Post by: rainb1ood on Thu, 12 November 2015, 20:05:53
Post by: trenzafeeds on Fri, 13 November 2015, 02:22:59
Post by: Karura on Fri, 13 November 2015, 03:19:13
fnzzy's photos
I've been summoned!
Added some colorShow Image(http://i.imgur.com/bhcoxq2.jpg)Show Image(http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...Show Image(http://i.imgur.com/chWHLUs.jpg)Show Image(http://i.imgur.com/mNTX85q.jpg)Show Image(http://i.imgur.com/hw9LBCa.jpg)Show Image(http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
That is so awesome Fnzzy! Favourite TKL right now.
Do you know if those screw-in feet are for sale somewhere? I might want to pick up a few myself.
Post by: slushi on Fri, 13 November 2015, 07:51:09
fnzzy's photos
I've been summoned!
Added some colorShow Image(http://i.imgur.com/bhcoxq2.jpg)Show Image(http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...Show Image(http://i.imgur.com/chWHLUs.jpg)Show Image(http://i.imgur.com/mNTX85q.jpg)Show Image(http://i.imgur.com/hw9LBCa.jpg)Show Image(http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
That is so awesome Fnzzy! Favourite TKL right now.
Do you know if those screw-in feet are for sale somewhere? I might want to pick up a few myself.
I wonder if the GON feet would work. I kinda like those better but the ones Fnzzy has looks great too.
Post by: whentheclouds on Fri, 13 November 2015, 10:00:47
Post by: Steezus on Fri, 13 November 2015, 10:21:15
i think those feet are non-detachable. are they, fnzzy?
I'm sure they were screwed into the acrylic piece, I doubt they used any sort of adhesive.
Post by: E3E on Fri, 13 November 2015, 10:27:11
i think those feet are non-detachable. are they, fnzzy?
I'm sure they were screwed into the acrylic piece, I doubt they used any sort of adhesive.
I concur! They look like some I've seen on taobao a while back. All of these, including GON's tend to screw in from the bottom of the case.
Post by: Fnzzy on Fri, 13 November 2015, 10:34:54
Fun fact, I was going to buy black feet from GON but decided against it because it didn't feel like it was worth the shipping from korea.
EDIT:
Quote
ESC right is from the top SetNumlockState Sets the state of the Numlock, Caps Lock, Scroll Lock
I should read.
Post by: elton5354 on Sat, 14 November 2015, 11:37:02
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50
(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Post by: Fnzzy on Sat, 14 November 2015, 11:42:11
also
(http://puu.sh/llkEP/6ca5634be2.jpg)
Post by: nguyenkimtam on Sat, 14 November 2015, 11:47:08
On another topic while we wait for the next batch to ship...100% join it :thumb: :thumb: :thumb:
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Post by: Steezus on Sat, 14 November 2015, 11:49:01
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Not a big fan of the 75% layout but damn that looks amazing! :thumb:
Post by: billnye on Sat, 14 November 2015, 12:04:45
Beautiful. Your pictures are always stunning.fnzzy's photos
I've been summoned!
Added some colorShow Image(http://i.imgur.com/bhcoxq2.jpg)Show Image(http://i.imgur.com/0XBbRc2.jpg)
Afternoon Delight - It's getting dark so fast these days...Show Image(http://i.imgur.com/chWHLUs.jpg)Show Image(http://i.imgur.com/mNTX85q.jpg)Show Image(http://i.imgur.com/hw9LBCa.jpg)Show Image(http://i.imgur.com/jop7RAc.jpg)
More pictures of different keyset combinations to come :))
Post by: E3E on Sat, 14 November 2015, 16:19:06
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Please no. My wallet, it can't handle it! Is this happening really soon, or are we going to get some down time before the Octagon v2 hits?
Damn I can't just keep buying Duck boards, I need some variety!
alsoShow Image(http://puu.sh/llkEP/6ca5634be2.jpg)
Jesus, is this the plan? truecustom and co are very ambitious already planning for the Orion v3 before all of these are even out. :eek:
Looks like people who want an Eagle/Viper v2 are getting shafted then? :P
I have an odd feeling that the new 75% isn't going to be called "Octagon" this time around. He seems to have removed the little nameplate piece that creates the "octagon" form factor, but then he does list it as the next GB.
Post by: ika on Sat, 14 November 2015, 17:02:30
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Jesus christ. I think I shed an actual tear looking at those pics.
Post by: appleonama on Sat, 14 November 2015, 20:34:48
75% are meme boards :^)
Post by: Karura on Sat, 14 November 2015, 20:44:22
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Jesus christ. I think I shed an actual tear looking at those pics.
There are better 75% out there, but damn this one looks quite good as well. :)
Post by: alienman82 on Sat, 14 November 2015, 20:46:39
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
Jesus christ. I think I shed an actual tear looking at those pics.
There are better 75% out there, but damn this one looks quite good as well. :)
like what?
Post by: Prankk on Sat, 14 November 2015, 21:22:29
(http://i.imgur.com/FHGbR2i.jpg)
Post by: TLSC.wipeOut on Sun, 15 November 2015, 01:34:16
Post by: gadzkun on Sun, 15 November 2015, 03:50:14
So when are the Orion V3's incoming?? I'll wait for those xD
after octagon V2 > lightsaver V3 > Orion V3 xD
Post by: Fnzzy on Sun, 15 November 2015, 04:50:07
Post by: Steezus on Sun, 15 November 2015, 07:16:05
I wonder how different the Orion v3 will be. I mean it has to be different enough to justify a purchase by someone who already has a v1 or v2. If it's just for people who missed out on previous GBs why not do more rounds of the v2? Anyway I am sure Duck has some neat stuff planned.
If you think about it the Orion v3 GB probably won't happen until 2017. This one has currently taken 7 months and it's almost done, with two more group buys in front of that then 2016 is basically filled up.
Post by: E3E on Sun, 15 November 2015, 09:14:45
I wonder how different the Orion v3 will be. I mean it has to be different enough to justify a purchase by someone who already has a v1 or v2. If it's just for people who missed out on previous GBs why not do more rounds of the v2? Anyway I am sure Duck has some neat stuff planned.
Personally, I don't even think Duck knows exactly how different it will be just yet this close off the heels of the Orion v2, but it definitely shows that he really wants to do another version already, haha.
What was the first Duck custom? The Kingsaver/Duck Mini? Then what, the Lightsaver, Lightpad, Orion, Lightsaver v2, Eagle/Viper, Octagon, Orion v2? I'm really curious about the timeline.
I think it's too early to really say what the v3 will have in store, but I think it could possibly have SMD underswitch backlighting like the GON NERD 60 v2 PCBs or 4 pin RGB in-switch backlighting for starters. The angle will probably be the same (for the aluminum options), but perhaps there will be even more intricate machining on the case, since you can clearly see that going from the v1 Lightsaver to the v2 Lightsaver and now the Orion v2, which is the first "third gen" design, I believe. The design will probably remain a two-piece design for all future generations of his boards unless Duck thinks of some crazy one-piece design.
I'm honestly surprised the 75% layout was embraced the way it has been. A lot of people didn't expect an Octagon v2 because of how unpopular the layout typically is compared to other layouts. There hasn't been much of a gap between Octagon v1 an the announcement of its successor.
Post by: ViệtNV on Sun, 15 November 2015, 12:03:57
Post by: Fnzzy on Sun, 15 November 2015, 18:45:38
The design will probably remain a two-piece design for all future generations of his boards unless Duck thinks of some crazy one-piece design.
Make one piece TKL housing. Make slid at the side which you close with an acryllic insert. Slide PCB in and screw onto the bottom part. Put switches from above into the pre-soldered SIP sockets.
:^)
Post by: ccc24 on Sun, 15 November 2015, 18:53:38
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
There all beautiful boards can't wait for the octagon. Are the indicator leds included?
Post by: E3E on Sun, 15 November 2015, 18:58:18
The design will probably remain a two-piece design for all future generations of his boards unless Duck thinks of some crazy one-piece design.
Make one piece TKL housing. Make slid at the side which you close with an acryllic insert. Slide PCB in and screw onto the bottom part. Put switches from above into the pre-soldered SIP sockets.
:^)
Pretty cool idea. That is definitely one way to do it. :D
Post by: E3E on Sun, 15 November 2015, 18:59:12
On another topic while we wait for the next batch to ship...
Duck's new 75% anyone....?
http://kbdlab.co.kr/index.php?document_srl=3200082&mid=board_Lsno50Show Image(http://kbdlab.co.kr/files/attach/images/340/082/200/003/33782148115c2fa218153849bb427044.JPG)
There all beautiful boards can't wait for the octagon. Are the indicator leds included?
Like the Orion, you'll have to add those yourself, I would imagine, but there will definitely be the pin holes for the indicators to flash through, which is awesome. :D
Post by: elton5354 on Sun, 15 November 2015, 19:16:25
Post by: E3E on Sun, 15 November 2015, 19:23:02
I heard the new 75% will offer the same options as Orion V2. :eek:
Awesome. That's what I figured. :D I'm definitely going to go for red again. It's just my favorite color for the 75% form. I don't think I'd like the others as much if I got another color.
Though IF Alps becomes available, then I might look at a lighter color to go with Alpine Winter.
Time will tell :D
Post by: ccc24 on Sun, 15 November 2015, 19:48:17
Post by: E3E on Sun, 15 November 2015, 20:33:18
So many options don't know which I like more :p. Which leds should I buy for the indicators?
For the Orion v2 I put together for the ever-so-awesome rainb1ood, I used 2x4x5mm LEDs, as those were the most colorful I had on hand. Can confirm that autoswitching 2 pin RGB LED work on the indicator lights, and they look awesome as an indicator. You can pick up different (RGB) varieties on eBay. I used Aliexpress for the 2x4x5mm LEDs.
But yeah, any kind will work! People tend to favor 1.8mm LEDs since they will not conflict with the downstroke of keys with thick Cherry profile caps like 2x4x5mm LEDs can. I'd recommend them honestly. I'm lucky I use SA on my Octagon, because the LEDs did create problems when I used them with my Gateron PBT set.
Post by: ccc24 on Sun, 15 November 2015, 21:05:34
So many options don't know which I like more :p. Which leds should I buy for the indicators?
For the Orion v2 I put together for the ever-so-awesome rainb1ood, I used 2x4x5mm LEDs, as those were the most colorful I had on hand. Can confirm that autoswitching 2 pin RGB LED work on the indicator lights, and they look awesome as an indicator. You can pick up different (RGB) varieties on eBay. I used Aliexpress for the 2x4x5mm LEDs.
But yeah, any kind will work! People tend to favor 1.8mm LEDs since they will not conflict with the downstroke of keys with thick Cherry profile caps like 2x4x5mm LEDs can. I'd recommend them honestly. I'm lucky I use SA on my Octagon, because the LEDs did create problems when I used them with my Gateron PBT set.
sounds good thanks
Post by: rainb1ood on Mon, 16 November 2015, 06:54:11
Can't wait to receive the masterfully crafted board from you
Post by: ryptide11 on Mon, 16 November 2015, 09:38:46
Post by: elton5354 on Mon, 16 November 2015, 09:56:57
Any idea when the second batch will ship?
I was told a month after the 1st batch was shipped
Post by: Want on Tue, 17 November 2015, 02:36:53
Any idea when the second batch will ship?
I was told a month after the 1st batch was shipped
Are the angled acrylic bottoms coming with this shipment, or is that a separate shipment? Gotta say, someone really dropped the ball on those angled acrylic.
Post by: filphil on Wed, 18 November 2015, 09:52:07
Just one for now.
Post by: R1N3 on Wed, 18 November 2015, 10:13:32
What bottom though??
Post by: filphil on Wed, 18 November 2015, 10:26:52
Glorious..
What bottom though??
:D
(http://i.imgur.com/0eg2zAg.jpg)
Post by: slushi on Wed, 18 November 2015, 11:00:23
Looks awesome dude!Glorious..
What bottom though??
:DShow Image(http://i.imgur.com/0eg2zAg.jpg)
Post by: alienman82 on Wed, 18 November 2015, 11:09:14
Show Image(http://i.imgur.com/6mjcFoW.jpg)
Just one for now.
are those dyesubs or ds?
Post by: Steezus on Wed, 18 November 2015, 13:38:07
Post by: ccc24 on Wed, 18 November 2015, 15:34:43
Post by: E3E on Wed, 18 November 2015, 15:54:13
anyone have pictures of the angled acrylic bottom?
Here's some pictures from my build log for rainb1ood.
The acrylic bottom is super cool and very hefty, imo. Solid. :)
(http://i.imgur.com/f4oPfzN.jpg)
(http://i.imgur.com/2VwRlPh.jpg)
(http://i.imgur.com/AocyaZi.jpg)
Sorry, I know my camera sucks. :P
Post by: ccc24 on Wed, 18 November 2015, 16:46:54
anyone have pictures of the angled acrylic bottom?
Here's some pictures from my build log for rainb1ood.
The acrylic bottom is super cool and very hefty, imo. Solid. :)Show Image(http://i.imgur.com/f4oPfzN.jpg)Show Image(http://i.imgur.com/2VwRlPh.jpg)Show Image(http://i.imgur.com/AocyaZi.jpg)
Sorry, I know my camera sucks. :P
Looks good, I definitely know what I'm getting on the Octagon now can't wait.
How do the zealios feel on an acrylic plate?
Post by: slushi on Wed, 18 November 2015, 16:52:15
Post by: E3E on Wed, 18 November 2015, 17:00:46
Wow E2E, very nice. I may need to contact you for my own build since I don't really want to chance this board's PCB with my first soldering experience. Mine looks to be the exact same build as rainb1ood's.
Haha, I'd be happy too! I usually just ya know, do my own builds, but it's really nice having the opportunity to put together builds of really cool boards for others like this.
Just send me a PM with whatever you'd like done and I'd be happy to work with you! :D
Looks good, I definitely know what I'm getting on the Octagon now can't wait.
How do the zealios feel on an acrylic plate?
Can't tell you how they feel; you'll have to ask rainb1ood for that one. I never put caps on the board, haha. Though I hear that plastic plates and direct mounting to PCBs are popular for tactile switches. I have a Rapoo KX that I use some ergo clears with (it was my first board, lol), and I have to admit, it's a very smooth and soft feel while keeping the tactility. No flex in my case, but I can't speak for the Orion. A shorter board like the Octagon should have even less flex if any.
Yeah, I'm really hyped about the new Octagon. Though I probably will just go with the aluminum bottom. Either that or buy one of each and then sell off what I don't care for (if anyone would even be in the market for that, haha). I hope Alps will be possible for it, but I'll still buy it even if not.
Post by: rainb1ood on Wed, 18 November 2015, 17:04:02
Post by: appleonama on Wed, 18 November 2015, 18:26:35
Glorious..
What bottom though??
:DShow Image(http://i.imgur.com/0eg2zAg.jpg)
i got the same combo im so happy i creamed
Post by: Phillipj06 on Wed, 18 November 2015, 19:23:55
Post by: trenzafeeds on Wed, 18 November 2015, 19:29:02
Sad I missed out on this GB. Any idea when/if the next round will be.
Read the last like two thread pages.
Post by: E3E on Wed, 18 November 2015, 19:30:04
Sad I missed out on this GB. Any idea when/if the next round will be.
Probably this time or a bit later next year or early 2017
Post by: rainb1ood on Wed, 18 November 2015, 19:51:17
I'm using chrome's translator and I get the basics of some function but I'd like to learn more about the 02D mapper and some of the translation does not make sense.
Post by: filphil on Wed, 18 November 2015, 19:58:40
Post by: rainb1ood on Wed, 18 November 2015, 20:07:35
I've been reading this translated text over and over too and trying to understand:
Code: [Select]
Maximum brightness automatic control of the switch LED and RGB LED
In the 500mA of USB 2.0 switch with LED status lights, effects, conditions, and automatically controlling the brightness of the colors of the RGB
If the switch LED except for the bypass mode and multi-LED disabled
It can affect the brightness of RGB when the bypass mode. (Full LED OFF switch at the maximum, full ON, minimum brightness)
Bypass mode only affects switch LED mode.
The maximum power setting
LED as the ability to set the maximum current value available in the (RGB included),
All responsibility for the operation and fault when setting its functions are attributed to your own.
For a USB output current of the devices used (PC, etc.), if you only set generous.
Example) lights up the entire bypass switch LED (LED multi-use) to secure an RGB LED brightness in the state.
> Setting
After entering control mode,
SCM Enter, enter,
Pressing a number from 500 to 900 slowly (base 500)
Control mode, press (Save)
Control mode is exited with ESC
Using the event of default after reset operational errors or dead 500
Keyboard LED LED Down key and then press the Stop recognized
After changing power settings
Post by: elton5354 on Wed, 18 November 2015, 21:34:54
Any idea when the second batch will ship?
I was told a month after the 1st batch was shipped
Are the angled acrylic bottoms coming with this shipment, or is that a separate shipment? Gotta say, someone really dropped the ball on those angled acrylic.
Yeah, everything is going to shipped together. Makes no sense in shipping separately as that will add cost and time (packaging and shipping twice). You won't find a better acrylic bottom than this hence the tough QC on them and thus took much longer to produce. I'd imagine they wasted more money and time trying to produce them.
Post by: Dreamre on Thu, 19 November 2015, 11:07:52
Any idea when the second batch will ship?
I was told a month after the 1st batch was shipped
Are the angled acrylic bottoms coming with this shipment, or is that a separate shipment? Gotta say, someone really dropped the ball on those angled acrylic.
Yeah, everything is going to shipped together. Makes no sense in shipping separately as that will add cost and time (packaging and shipping twice). You won't find a better acrylic bottom than this hence the tough QC on them and thus took much longer to produce. I'd imagine they wasted more money and time trying to produce them.
Thanks for the update, Elton! You're the best GB leader. :thumb: :)) :-*
Post by: filphil on Thu, 19 November 2015, 16:13:11
I'd like to know what Control Mode, Key lock, Push lock, Change lock, LED bypass, etc. does
I've been reading this translated text over and over too and trying to understand:Code: [Select]Maximum brightness automatic control of the switch LED and RGB LED
In the 500mA of USB 2.0 switch with LED status lights, effects, conditions, and automatically controlling the brightness of the colors of the RGB
If the switch LED except for the bypass mode and multi-LED disabled
It can affect the brightness of RGB when the bypass mode. (Full LED OFF switch at the maximum, full ON, minimum brightness)
Bypass mode only affects switch LED mode.
The maximum power setting
LED as the ability to set the maximum current value available in the (RGB included),
All responsibility for the operation and fault when setting its functions are attributed to your own.
For a USB output current of the devices used (PC, etc.), if you only set generous.
Example) lights up the entire bypass switch LED (LED multi-use) to secure an RGB LED brightness in the state.
> Setting
After entering control mode,
SCM Enter, enter,
Pressing a number from 500 to 900 slowly (base 500)
Control mode, press (Save)
Control mode is exited with ESC
Using the event of default after reset operational errors or dead 500
Keyboard LED LED Down key and then press the Stop recognized
After changing power settings
Wish I could help you out. That translation pains me too. =(
http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=3208312
WHAT IS THIS
(http://kbdlab.co.kr/files/attach/images/340/312/208/003/1223e0148468551bdd73272092c321c0.JPG)
(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0f8164cf2f161d9b512b4d36e2110e58.JPG)
(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0e4c122dae33dfcedc3a1a61b00bc351.JPG)
(http://kbdlab.co.kr/files/attach/images/340/312/208/003/321d33e9228b3c5e74d1dff34035d71c.JPG)
Post by: romevi on Thu, 19 November 2015, 16:15:03
Waddle, waddle.
Post by: yicaoyimu on Thu, 19 November 2015, 16:17:23
I'd like to know what Control Mode, Key lock, Push lock, Change lock, LED bypass, etc. does
I've been reading this translated text over and over too and trying to understand:Code: [Select]Maximum brightness automatic control of the switch LED and RGB LED
In the 500mA of USB 2.0 switch with LED status lights, effects, conditions, and automatically controlling the brightness of the colors of the RGB
If the switch LED except for the bypass mode and multi-LED disabled
It can affect the brightness of RGB when the bypass mode. (Full LED OFF switch at the maximum, full ON, minimum brightness)
Bypass mode only affects switch LED mode.
The maximum power setting
LED as the ability to set the maximum current value available in the (RGB included),
All responsibility for the operation and fault when setting its functions are attributed to your own.
For a USB output current of the devices used (PC, etc.), if you only set generous.
Example) lights up the entire bypass switch LED (LED multi-use) to secure an RGB LED brightness in the state.
> Setting
After entering control mode,
SCM Enter, enter,
Pressing a number from 500 to 900 slowly (base 500)
Control mode, press (Save)
Control mode is exited with ESC
Using the event of default after reset operational errors or dead 500
Keyboard LED LED Down key and then press the Stop recognized
After changing power settings
Wish I could help you out. That translation pains me too. =(
http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=3208312
WHAT IS THISShow Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/1223e0148468551bdd73272092c321c0.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0f8164cf2f161d9b512b4d36e2110e58.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0e4c122dae33dfcedc3a1a61b00bc351.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/321d33e9228b3c5e74d1dff34035d71c.JPG)
Unicorn X3. Great full metal keyboard look but less clumsy. I like it.
Post by: Steezus on Thu, 19 November 2015, 16:25:13
Post by: slushi on Thu, 19 November 2015, 16:25:29
Post by: filphil on Fri, 20 November 2015, 09:57:47
Post by: ccc24 on Sun, 22 November 2015, 12:23:21
Post by: Steezus on Sun, 22 November 2015, 12:31:26
(https://farm1.staticflickr.com/771/22819084157_e504f3e9ec_z.jpg) (https://flic.kr/p/ALrLHt)
Orion v2 w/ OTD Red Alert 2 (https://flic.kr/p/ALrLHt) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Post by: ccc24 on Sun, 22 November 2015, 14:26:25
Teaser Pic :thumb:
(https://farm1.staticflickr.com/771/22819084157_e504f3e9ec_z.jpg) (https://flic.kr/p/ALrLHt)
Orion v2 w/ OTD Red Alert 2 (https://flic.kr/p/ALrLHt) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Nice board. I was looking through your pictures, did you put those sip sockets in for the indicator leds or did they come installed with the pcb?
Post by: Steezus on Sun, 22 November 2015, 14:37:19
Teaser Pic :thumb:
(https://farm1.staticflickr.com/771/22819084157_e504f3e9ec_z.jpg) (https://flic.kr/p/ALrLHt)
Orion v2 w/ OTD Red Alert 2 (https://flic.kr/p/ALrLHt) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Nice board. I was looking through your pictures, did you put those sip sockets in for the indicator leds or did they come installed with the pcb?
Thanks I put them in myself, it was a little tricky trying to hold them in place to solder so I put a piece of tape on the other side to hold it so I could flip it over and solder them on.
Post by: E3E on Sun, 22 November 2015, 14:43:40
do we have an eta on the Octagon and the estimated turn around time for it?
I'm hoping it's not too soon. My wallet is going to commit sudoku at this rate. I'd be happy if it's at the end of January or start of February.
Post by: ccc24 on Sun, 22 November 2015, 14:59:32
do we have an eta on the Octagon and the estimated turn around time for it?
I'm hoping it's not too soon. My wallet is going to commit sudoku at this rate. I'd be happy if it's at the end of January or start of February.
haha ya I keep buying stuff instead of saving for this GB. I think though I'm going to follow you and go with the red case and purchase the Coke JTK set to match.
Post by: E3E on Sun, 22 November 2015, 15:16:29
do we have an eta on the Octagon and the estimated turn around time for it?
I'm hoping it's not too soon. My wallet is going to commit sudoku at this rate. I'd be happy if it's at the end of January or start of February.
haha ya I keep buying stuff instead of saving for this GB. I think though I'm going to follow you and go with the red case and purchase the Coke JTK set to match.
Haha, yeah I noticed that set and thought the same thing, well more so with my original Octagon. I thought it was ironic since I was thinking of Coca/Nuka Cola when I saw Jukebox and the Red Octagon.
I think I'm actually going to go for a silver base and a titanium gray bottom for the SNES GMK set though. It totally changed my plans. I remember when the Jazz Solo Cup vs SNES poll went up but I forgot all about that design until it popped up on reddit the other day.
I figure since I already have a red one, I might as well, haha. I hear you on buying instead of saving. It's too easy to do that in this hobby. :P
Post by: Steezus on Sun, 22 November 2015, 17:59:12
Post by: slushi on Sun, 22 November 2015, 18:06:04
Post by: E3E on Sun, 22 November 2015, 18:10:36
Anytime I try to save the keymap .hex file I get a runtime error, anybody else experiencing this?
Yeah, this is a common issue with the 02D software, I think.
Create a text file and rename it whatever you want, but change the extension to .hex
Then create your keymap and save it over that file.
In otherwords, you need to have a dummy file to save keymaps. O2D trends to screw up if you try to create a new file.
Post by: Steezus on Sun, 22 November 2015, 18:26:55
Anytime I try to save the keymap .hex file I get a runtime error, anybody else experiencing this?
Yeah, this is a common issue with the 02D software, I think.
Create a text file and rename it whatever you want, but change the extension to .hex
Then create your keymap and save it over that file.
In otherwords, you need to have a dummy file to save keymaps. O2D trends to screw up if you try to create a new file.
Thank you very much, that fixed the problem. :thumb:
Post by: yuktsi on Sun, 22 November 2015, 18:32:27
Post by: alienman82 on Sun, 22 November 2015, 18:33:24
When will be the rest be shipped? I am hoping this to arrive before Christmas :blank:
Yeah me too bro
Post by: Steezus on Sun, 22 November 2015, 19:09:06
Post by: slushi on Sun, 22 November 2015, 19:17:53
I was finally able to flash the board with a hex file that was to made to my liking. Once you get everything done this board is amazing, a little confusing learning how to use the keymapper and flash the board but it didn't take too long.Yeah I had the same issues with the duck eagle
Post by: nguyenkimtam on Mon, 23 November 2015, 00:42:08
When will be the rest be shipped? I am hoping this to arrive before Christmas :blank:I think next month :mad: :mad: :mad:
Post by: Steezus on Mon, 23 November 2015, 09:59:41
When will be the rest be shipped? I am hoping this to arrive before Christmas :blank:I think next month :mad: :mad: :mad:
Elton was told the second batch would be shipped a month after the first batch. If everything goes to plan then you probably will have it before Christmas. The mail is going to start slowing down to with the holidays. :(
Post by: slushi on Mon, 23 November 2015, 10:03:29
:P
Post by: Steezus on Mon, 23 November 2015, 11:12:54
(https://farm1.staticflickr.com/639/23249688155_5e69c98b32_z.jpg) (https://flic.kr/p/BquJhk)
Orion v2 Acrylic Bottom 1 (https://flic.kr/p/BquJhk) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Post by: slushi on Mon, 23 November 2015, 11:42:03
Your board looks amazing... sigh.
Post by: Steezus on Mon, 23 November 2015, 11:45:53
You're the worst! Just. The. Worst.
Your board looks amazing... sigh.
:p, at least you know you're board will be nothing but perfect when it comes. I'm more of a fan of the aluminum bottom than the acrylic, the plastic plate also gives a beautiful illumination under the caps.
Post by: slushi on Mon, 23 November 2015, 12:09:44
You're the worst! Just. The. Worst.
Your board looks amazing... sigh.
:p, at least you know you're board will be nothing but perfect when it comes. I'm more of a fan of the aluminum bottom than the acrylic, the plastic plate also gives a beautiful illumination under the caps.
Yeah, I wish I could find someone who was willing to sell their black aluminum bottom.
Post by: rainb1ood on Mon, 23 November 2015, 12:17:06
(http://images.tapatalk-cdn.com/15/11/23/8d664fba16ed66f1996a7dafab60e764.jpg)
Post by: alienman82 on Mon, 23 November 2015, 12:37:19
Show Image(http://images.tapatalk-cdn.com/15/11/23/077a5a0ca58b2ad36462f15f76a81d64.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/23/8d664fba16ed66f1996a7dafab60e764.jpg)
I love it! so stealthy!
Post by: E3E on Mon, 23 November 2015, 13:25:29
Show Image(http://images.tapatalk-cdn.com/15/11/23/077a5a0ca58b2ad36462f15f76a81d64.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/23/8d664fba16ed66f1996a7dafab60e764.jpg)
She's a beaut! :thumb: Love the all black look of your boards, man.
Also, yeah... Thanks to expenditures, I'm likely only going to get the aluminum bottom for my Octagon v2 instead of all three. Also partially because I can see myself thinking it's a cool idea to swap out at will but quickly realizing it's a pain in the ass to undo and refasten all the screws every time I want to change the bottom. Plus, the 11 degree incline goes perfect with my Lightpad and wrist rest, nooot to meniton the fact I have a spare set of side insert wedges that are just waiting for that alu bottom. :)
Post by: Steezus on Mon, 23 November 2015, 13:50:56
Show Image(http://images.tapatalk-cdn.com/15/11/23/077a5a0ca58b2ad36462f15f76a81d64.jpg)Show Image(http://images.tapatalk-cdn.com/15/11/23/8d664fba16ed66f1996a7dafab60e764.jpg)
She's a beaut! :thumb: Love the all black look of your boards, man.
Also, yeah... Thanks to expenditures, I'm likely only going to get the aluminum bottom for my Octagon v2 instead of all three. Also partially because I can see myself thinking it's a cool idea to swap out at will but quickly realizing it's a pain in the ass to undo and refasten all the screws every time I want to change the bottom. Plus, the 11 degree incline goes perfect with my Lightpad and wrist rest, nooot to meniton the fact I have a spare set of side insert wedges that are just waiting for that alu bottom. :)
Switching the bottom is a pain. I had already taken mine off so many times to swap out an indicator LED, to take pics of the acrylic bottom, etc.
Post by: ninjadoc on Mon, 23 November 2015, 17:05:02
Anytime I try to save the keymap .hex file I get a runtime error, anybody else experiencing this?
yes. It is driving me ape**** crazy! I'll try the save file trick with a blank file. Damn runtime errors!!!
Post by: Steezus on Mon, 23 November 2015, 17:14:00
Anytime I try to save the keymap .hex file I get a runtime error, anybody else experiencing this?
yes. It is driving me ape**** crazy! I'll try the save file trick with a blank file. Damn runtime errors!!!
The file trick fixed it for me, it was a little confusing at first with the error but thanks to E3E it was an easy fix. :thumb:
Post by: rainb1ood on Mon, 23 November 2015, 19:30:23
She's a beaut! :thumb: Love the all black look of your boards, man.
I love it! so stealthy!
Thanks! Cherry WoB are all time favorite set!
Post by: Rainbow_ on Mon, 23 November 2015, 21:22:31
Whie you're waiting, here's a pic of the acrylic angled bottom. :thumb:
(https://farm1.staticflickr.com/639/23249688155_5e69c98b32_z.jpg) (https://flic.kr/p/BquJhk)
Orion v2 Acrylic Bottom 1 (https://flic.kr/p/BquJhk) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Makes me wish I got the WKL top
Post by: E3E on Mon, 23 November 2015, 21:31:45
Whie you're waiting, here's a pic of the acrylic angled bottom. :thumb:
(https://farm1.staticflickr.com/639/23249688155_5e69c98b32_z.jpg) (https://flic.kr/p/BquJhk)
Orion v2 Acrylic Bottom 1 (https://flic.kr/p/BquJhk) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Makes me wish I got the WKL top
Variety is the spice of life! But yeah, the symmetry of WKL with the filled-in positions there is very attractive.
Post by: missalaire on Mon, 23 November 2015, 21:50:20
(http://i.imgur.com/WK19wPg.jpg)
(http://i.imgur.com/zg94xvk.jpg)
(http://i.imgur.com/r0ZG72L.jpg)
The work is being done by dorkvader.
Someone sell me your flat acrylic bottom!
Post by: slushi on Mon, 23 November 2015, 22:39:43
Progress so far :)Looks awesome! I'd trade you bottoms lol.Show Image(http://i.imgur.com/WK19wPg.jpg)Show Image(http://i.imgur.com/zg94xvk.jpg)Show Image(http://i.imgur.com/r0ZG72L.jpg)
The work is being done by dorkvader.
Someone sell me your flat acrylic bottom!
Post by: missalaire on Mon, 23 November 2015, 22:51:24
Progress so far :)Looks awesome! I'd trade you bottoms lol.Show Image(http://i.imgur.com/WK19wPg.jpg)Show Image(http://i.imgur.com/zg94xvk.jpg)Show Image(http://i.imgur.com/r0ZG72L.jpg)
The work is being done by dorkvader.
Someone sell me your flat acrylic bottom!
But I want both bottoms ;_;
Post by: slushi on Mon, 23 November 2015, 22:52:39
I know that feel lolProgress so far :)Looks awesome! I'd trade you bottoms lol.Show Image(http://i.imgur.com/WK19wPg.jpg)Show Image(http://i.imgur.com/zg94xvk.jpg)Show Image(http://i.imgur.com/r0ZG72L.jpg)
The work is being done by dorkvader.
Someone sell me your flat acrylic bottom!
But I want both bottoms ;_;
Post by: yuktsi on Tue, 24 November 2015, 19:01:52
Post by: elton5354 on Wed, 25 November 2015, 10:25:35
They were:
Tuantruong
Laguar
Sed8op8
lionblinds
I have updated the tracking in the order list.
Post by: filphil on Wed, 25 November 2015, 10:38:42
There were 4 orders that was shipped out on Monday that was supposed to be in the first batch as well.
They were:
Tuantruong
Laguar
Sed8op8
lionblinds
I have updated the tracking in the order list.
Welcome to the club, friends.
Post by: Pemdas on Wed, 25 November 2015, 12:24:30
There were 4 orders that was shipped out on Monday that was supposed to be in the first batch as well.
They were:
Tuantruong
Laguar
Sed8op8
lionblinds
I have updated the tracking in the order list.
Is the rest of the first batch still on schedule for shipping next week?
Post by: MarkRobbo on Fri, 27 November 2015, 17:21:02
Unfortunately my flat acrylic bottom came out of the packaging super scratched up. It was packaged quite well, so I won't really know how it got scratched this badly if it happened in transit but...
Hard to picture:
(http://i.imgur.com/Q2CfwiQh.jpg)
Post by: Rainbow_ on Fri, 27 November 2015, 18:40:50
Finally had chance to unpack my order, and wow. Super impressive
Unfortunately my flat acrylic bottom came out of the packaging super scratched up. It was packaged quite well, so I won't really know how it got scratched this badly if it happened in transit but...
Hard to picture:Show Image(http://i.imgur.com/Q2CfwiQh.jpg)
Did you remove the protective film? AFAIK it should have come with that, as did the inserts for the aluminum bottom.
Post by: filphil on Fri, 27 November 2015, 19:28:45
Finally had chance to unpack my order, and wow. Super impressive
Unfortunately my flat acrylic bottom came out of the packaging super scratched up. It was packaged quite well, so I won't really know how it got scratched this badly if it happened in transit but...
Hard to picture:Show Image(http://i.imgur.com/Q2CfwiQh.jpg)
Did you remove the protective film? AFAIK it should have come with that, as did the inserts for the aluminum bottom.
Very much this. It looks like it still has the film plus the made in korea sticker is a dead give away. =D
Also I love your avatars, rainbow
Post by: MarkRobbo on Sat, 28 November 2015, 06:31:38
But I'm glad of that in this case :P
Post by: appleonama on Sat, 28 November 2015, 09:59:37
Post by: alienman82 on Sat, 28 November 2015, 10:03:38
never getting it am i? 9months and countingbreh gotta resist selling that spot
Post by: trenzafeeds on Sat, 28 November 2015, 10:04:10
never getting it am i? 9months and countingbreh gotta resist selling that spot
I will buy happily
Post by: alienman82 on Sat, 28 November 2015, 10:07:52
never getting it am i? 9months and countingbreh gotta resist selling that spot
I will buy happily
That was fast
Post by: laden3 on Sat, 28 November 2015, 15:19:00
Somebody halp prease.
Post by: Steezus on Sat, 28 November 2015, 15:25:52
How do I get my hands on these? http://kbdlab.co.kr/index.php?mid=board_Lsno50&page=2&document_srl=3230933 (just the feet)
Somebody halp prease.
I don't think anybody has them, the only time I ever even saw those being mentioned was in Leeku's Compact SQ group buy. I'm almost 100% positive that you could not order them for the Orion v2.
Post by: missalaire on Sat, 28 November 2015, 19:00:18
never getting it am i? 9months and counting
I will buy your flat acrylic bottom if you are open to parting with it :P
Post by: trenzafeeds on Sat, 28 November 2015, 19:13:12
never getting it am i? 9months and counting
I will buy your flat acrylic bottom if you are open to parting with it :P
Back off m80 I got dibs. :p
Post by: havenlau on Sun, 29 November 2015, 13:32:53
How do I order one????? :eek: :eek: :eek: :eek:I'd like to know what Control Mode, Key lock, Push lock, Change lock, LED bypass, etc. does
I've been reading this translated text over and over too and trying to understand:Code: [Select]Maximum brightness automatic control of the switch LED and RGB LED
In the 500mA of USB 2.0 switch with LED status lights, effects, conditions, and automatically controlling the brightness of the colors of the RGB
If the switch LED except for the bypass mode and multi-LED disabled
It can affect the brightness of RGB when the bypass mode. (Full LED OFF switch at the maximum, full ON, minimum brightness)
Bypass mode only affects switch LED mode.
The maximum power setting
LED as the ability to set the maximum current value available in the (RGB included),
All responsibility for the operation and fault when setting its functions are attributed to your own.
For a USB output current of the devices used (PC, etc.), if you only set generous.
Example) lights up the entire bypass switch LED (LED multi-use) to secure an RGB LED brightness in the state.
> Setting
After entering control mode,
SCM Enter, enter,
Pressing a number from 500 to 900 slowly (base 500)
Control mode, press (Save)
Control mode is exited with ESC
Using the event of default after reset operational errors or dead 500
Keyboard LED LED Down key and then press the Stop recognized
After changing power settings
Wish I could help you out. That translation pains me too. =(
http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=3208312
WHAT IS THISShow Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/1223e0148468551bdd73272092c321c0.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0f8164cf2f161d9b512b4d36e2110e58.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0e4c122dae33dfcedc3a1a61b00bc351.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/321d33e9228b3c5e74d1dff34035d71c.JPG)
Unicorn X3. Great full metal keyboard look but less clumsy. I like it.
Post by: aznairjordan on Sun, 29 November 2015, 19:22:16
There were 4 orders that was shipped out on Monday that was supposed to be in the first batch as well.
They were:
Tuantruong
Laguar
Sed8op8
lionblinds
I have updated the tracking in the order list.
elton, I sent you a PM just hope you get it before things ship!
Post by: nguyenkimtam on Sun, 29 November 2015, 21:25:11
It's also a group buy but was ended. So can not orderHow do I order one????? :eek: :eek: :eek: :eek:I'd like to know what Control Mode, Key lock, Push lock, Change lock, LED bypass, etc. does
I've been reading this translated text over and over too and trying to understand:Code: [Select]Maximum brightness automatic control of the switch LED and RGB LED
In the 500mA of USB 2.0 switch with LED status lights, effects, conditions, and automatically controlling the brightness of the colors of the RGB
If the switch LED except for the bypass mode and multi-LED disabled
It can affect the brightness of RGB when the bypass mode. (Full LED OFF switch at the maximum, full ON, minimum brightness)
Bypass mode only affects switch LED mode.
The maximum power setting
LED as the ability to set the maximum current value available in the (RGB included),
All responsibility for the operation and fault when setting its functions are attributed to your own.
For a USB output current of the devices used (PC, etc.), if you only set generous.
Example) lights up the entire bypass switch LED (LED multi-use) to secure an RGB LED brightness in the state.
> Setting
After entering control mode,
SCM Enter, enter,
Pressing a number from 500 to 900 slowly (base 500)
Control mode, press (Save)
Control mode is exited with ESC
Using the event of default after reset operational errors or dead 500
Keyboard LED LED Down key and then press the Stop recognized
After changing power settings
Wish I could help you out. That translation pains me too. =(
http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=3208312
WHAT IS THISShow Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/1223e0148468551bdd73272092c321c0.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0f8164cf2f161d9b512b4d36e2110e58.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/0e4c122dae33dfcedc3a1a61b00bc351.JPG)Show Image(http://kbdlab.co.kr/files/attach/images/340/312/208/003/321d33e9228b3c5e74d1dff34035d71c.JPG)
Unicorn X3. Great full metal keyboard look but less clumsy. I like it.
Post by: yuktsi on Mon, 30 November 2015, 02:55:06
Post by: appleonama on Mon, 30 November 2015, 03:24:41
When will mine be shipped? :-X :-X :-X :-X
:^) he said about a month seems like 3 more months to go
Post by: E3E on Mon, 30 November 2015, 06:29:26
http://duck0113.tistory.com/127
:-X I can't take it. I want them all!
Post by: rainb1ood on Mon, 30 November 2015, 06:58:13
I wonder if the new case will fit the v1 PCB? (Alu top + acrylic angled bottom)
Post by: whentheclouds on Mon, 30 November 2015, 07:13:17
led indicators look better in actual photos than in the render, but i still don't care much for them
Post by: E3E on Mon, 30 November 2015, 07:38:22
I think the original got its design from the original Orion, either that or the Lightsaver v2. It's all coming around again, haha.
I personally like the centered USB location. It's pretty unique. :) I'm gonna miss the little name plate that the original Octagon had for the stickers. :( Buuut, the rest makes up for it.
That's true too, since I have the original Octagon, I can always swap PCBs out for fun. That's a plus! I also agree with the indicators. I think they're innovative and different. Kinda harken back to old school keyboards, but they do look a little funny.
Post by: yicaoyimu on Mon, 30 November 2015, 12:21:02
Post by: meiosis on Mon, 30 November 2015, 18:08:26
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
Post by: yicaoyimu on Mon, 30 November 2015, 18:37:04
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
More is always better :))
Post by: E3E on Mon, 30 November 2015, 18:38:28
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
What is this best 75% you speak of? :P
Post by: Steezus on Mon, 30 November 2015, 20:52:39
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
What is this best 75% you speak of? :P
Leeku's 75% of the Compact SQ
Post by: E3E on Mon, 30 November 2015, 21:16:08
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
What is this best 75% you speak of? :P
Leeku's 75% of the Compact SQ
What is this 75% version of the SQ? I only see the 1800-style version.
Post by: Steezus on Mon, 30 November 2015, 21:17:13
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
What is this best 75% you speak of? :P
Leeku's 75% of the Compact SQ
What is this 75% version of the SQ? I only see the 1800-style version.
It hasn't been released yet, in the SQ's group buy he was discussing that the 75% is planned for the next group buy. He has several layouts that he is planning on selling.
Post by: E3E on Mon, 30 November 2015, 21:22:47
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
What is this best 75% you speak of? :P
Leeku's 75% of the Compact SQ
What is this 75% version of the SQ? I only see the 1800-style version.
It hasn't been released yet, in the SQ's group buy he was discussing that the 75% is planned for the next group buy. He has several layouts that he is planning on selling.
Gotcha. Thanks for the clarification. I'm wondering what it'll look like. I remember a 75% PCB being offered as part of the interest check Meiosis hosted a while back (one that ended up being suspended for a while), so I'm guessing that a case is being designed around it. So likely something like the SQ and RedScarf III, with an aluminum top and acrylic bottom?
Sounds tempting, but I'm not the biggest fans of those diffuse bottoms.
Post by: slushi on Mon, 30 November 2015, 21:25:03
Post by: E3E on Mon, 30 November 2015, 21:30:15
Is it sad to think that even though I haven't gotten the Orion yet, I know part of my money has already been claimed by the Octagon V2?
Oh, what are you planning to get for the Octagon v2? I certainly plan on getting a brass weight for the board if we can get a good source for them in the states, someone who can make Orion and Octagon brass weights. :D
I'm so glad that I'm really not "turned on" by TKL layouts, because there are far too many awesome TKLs coming out all the time. Strangely, I feel satisfied just hanging with the Octagon, even if other 75% boards come out. Definitely my happy place. I love the Duck boards.
I think it's the 11 degree angle and all the flashy lights. 02D is pretty intuitive too, if not just a little bit quirky.
Post by: slushi on Mon, 30 November 2015, 21:38:36
Is it sad to think that even though I haven't gotten the Orion yet, I know part of my money has already been claimed by the Octagon V2?
Oh, what are you planning to get for the Octagon v2? I certainly plan on getting a brass weight for the board if we can get a good source for them in the states, someone who can make Orion and Octagon brass weights. :D
I'm so glad that I'm really not "turned on" by TKL layouts, because there are far too many awesome TKLs coming out all the time. Strangely, I feel satisfied just hanging with the Octagon, even if other 75% boards come out. Definitely my happy place. I love the Duck boards.
I think it's the 11 degree angle and all the flashy lights. 02D is pretty intuitive too, if not just a little bit quirky.
Im not sure yet... I think you may have convinced me to try Alps on one of the two Duck boards... :)
Post by: E3E on Mon, 30 November 2015, 21:54:54
Is it sad to think that even though I haven't gotten the Orion yet, I know part of my money has already been claimed by the Octagon V2?
Oh, what are you planning to get for the Octagon v2? I certainly plan on getting a brass weight for the board if we can get a good source for them in the states, someone who can make Orion and Octagon brass weights. :D
I'm so glad that I'm really not "turned on" by TKL layouts, because there are far too many awesome TKLs coming out all the time. Strangely, I feel satisfied just hanging with the Octagon, even if other 75% boards come out. Definitely my happy place. I love the Duck boards.
I think it's the 11 degree angle and all the flashy lights. 02D is pretty intuitive too, if not just a little bit quirky.
Im not sure yet... I think you may have convinced me to try Alps on one of the two Duck boards... :)
Do it! >:D
It would be nice to have at least one with Alps! :D If the Octagon v2 ends up not having an Alps PCB option, I'm just going to throw in some linear Zealios to really soak up that RGB glow, and also since I prefer linears on my daily drivers. If I want to go tactile, I'll just swap in some vintage clear stems!
Post by: whentheclouds on Mon, 30 November 2015, 23:21:22
I'm so glad that I'm really not "turned on" by TKL layoutsme neither, though yutski's boards almost managed it. i still think wkl is the best layout aesthetics wise, but i like 75% for the compactness and the novelty
Post by: meiosis on Mon, 30 November 2015, 23:47:20
Octagon v2 is a two piece design? Now I really want it!
But you already have the best 75% coming :(
What is this best 75% you speak of? :P
Leeku's 75% of the Compact SQ
What is this 75% version of the SQ? I only see the 1800-style version.
It hasn't been released yet, in the SQ's group buy he was discussing that the 75% is planned for the next group buy. He has several layouts that he is planning on selling.
Gotcha. Thanks for the clarification. I'm wondering what it'll look like. I remember a 75% PCB being offered as part of the interest check Meiosis hosted a while back (one that ended up being suspended for a while), so I'm guessing that a case is being designed around it. So likely something like the SQ and RedScarf III, with an aluminum top and acrylic bottom?
Sounds tempting, but I'm not the biggest fans of those diffuse bottoms.
Ohh didn't mean to keep you guys guessing, it's an inside joke between me and yicao haha, no its not leeku's 75% compact version (that should be coming soon anyways)
--
The octagon 2 is amazing :) really digging the diffuser/indicator location
Post by: appleonama on Tue, 01 December 2015, 21:37:39
Post by: nguyenkimtam on Fri, 04 December 2015, 04:56:28
so update elton?Also have this question and waiting for batch 2 ship out
Post by: filphil on Fri, 04 December 2015, 07:32:17
Post by: slushi on Fri, 04 December 2015, 09:30:47
He's been good with the updates so rest easy. If anything I'd be worried about a board being shipped out during the holidays and tired workers dropping your box.
:eek: don't even say that!!! jk.
Post by: Lastpilot on Fri, 04 December 2015, 15:30:22
Post by: alienman82 on Fri, 04 December 2015, 15:37:25
Just an update, I received my Orion a while ago. November 4th.
blue alps?
Post by: Lastpilot on Fri, 04 December 2015, 21:10:59
Have not gotten the Alps yet for it...orange would be best XDJust an update, I received my Orion a while ago. November 4th.
blue alps?
Post by: E3E on Fri, 04 December 2015, 21:22:04
Have not gotten the Alps yet for it...orange would be best XDJust an update, I received my Orion a while ago. November 4th.
blue alps?
Good choice, good choice. :thumb:
Post by: filphil on Fri, 04 December 2015, 21:43:39
Have not gotten the Alps yet for it...orange would be best XDJust an update, I received my Orion a while ago. November 4th.
blue alps?
Check to see if you received the right screws. I think you're supposed to use 8 short screws but my flat piece came with 4 short and 4 long for the angled and aluminum bottom.
Post by: Lastpilot on Fri, 04 December 2015, 21:50:06
Check to see if you received the right screws. I think you're supposed to use 8 short screws but my flat piece came with 4 short and 4 long for the angled and aluminum bottom.
Is this good? Edit: Darn it looks like I need some screws.
(http://i.imgur.com/bYKIuSY.jpg)
Post by: pmh1410 on Fri, 04 December 2015, 21:53:19
http://duck0113.tistory.com/127
Post by: E3E on Fri, 04 December 2015, 22:01:28
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck every body ;)
Red Scarf 84?
Awesome, well hopefully the Octagon v2 GB happens not too long after, but I can respect if Elton would rather wait to be sure everyone gets their Orion v2 safely before starting. I guess we'll have to wait and see, but I'm ready!
Post by: pmh1410 on Fri, 04 December 2015, 22:09:38
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck every body ;)
Red Scarf 84?
Awesome, well hopefully the Octagon v2 GB happens not too long after, but I can respect if Elton would rather wait to be sure everyone gets their Orion v2 safely before starting. I guess we'll have to wait and see, but I'm ready!
BminiX2 PCB, Housing designed by VNMK team, assembled by me ;)
i still wait 3 DIY kits of Orion V2 :(
Post by: alienman82 on Fri, 04 December 2015, 22:11:23
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck every body ;)
Red Scarf 84?
Awesome, well hopefully the Octagon v2 GB happens not too long after, but I can respect if Elton would rather wait to be sure everyone gets their Orion v2 safely before starting. I guess we'll have to wait and see, but I'm ready!
BminiX2 PCB, Housing designed by VNMK team, assembled by me ;)
i still wait 3 DIY kits of Orion V2 :(
What is your favorite artisan you have?
Post by: yicaoyimu on Fri, 04 December 2015, 22:11:49
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck every body ;)
Red Scarf 84?
Awesome, well hopefully the Octagon v2 GB happens not too long after, but I can respect if Elton would rather wait to be sure everyone gets their Orion v2 safely before starting. I guess we'll have to wait and see, but I'm ready!
BminiX2 PCB, Housing designed by VNMK team, assembled by me ;)
i still wait 3 DIY kits of Orion V2 :(
Good to hear it's not some ripoff case your friend sent you.
Post by: ccc24 on Sat, 05 December 2015, 17:32:56
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck every body ;)
Red Scarf 84?
Awesome, well hopefully the Octagon v2 GB happens not too long after, but I can respect if Elton would rather wait to be sure everyone gets their Orion v2 safely before starting. I guess we'll have to wait and see, but I'm ready!
Did the korean's already have all their orders filled? Mind as well start our Octagon GB with theirs as well lol :p
Post by: PrpnNightmare on Sun, 06 December 2015, 16:44:49
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck everybody ;)
http://duck0113.tistory.com/127
If I was any more excited for this my eyes might have burst!
Post by: swimmingbird on Sun, 06 December 2015, 19:21:40
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck everybody ;)
http://duck0113.tistory.com/127
Damn that's like now :eek:
Post by: trenzafeeds on Sun, 06 December 2015, 21:30:52
Octagon V2 will open GB by Elton on GH, Korea GB will open at Monday 7 Dec 2015 (Maybe). Good Luck everybody ;)
http://duck0113.tistory.com/127
Damn that's like now :eek:
I think he means the groupbuy will start then in Korea, doesn't necessarily mean it will start at the same time here. I could be reading it wrong though.
Post by: raymogi on Sun, 06 December 2015, 21:32:52
Post by: ika on Sun, 06 December 2015, 21:36:05
Post by: romevi on Sun, 06 December 2015, 21:38:53
Post by: Pemdas on Sun, 06 December 2015, 21:39:48
Anyone know how quickly the spots filled up for the Orion when the GB started?
If I remember correctly the first 30 were gone within the first couple hours
I placed my order like an hour and a half after and got spot 23
Comparatively. I tried to join the yuktsi Jane ce buy 10 minutes after the post and was too late to get in.
Post by: trenzafeeds on Sun, 06 December 2015, 21:41:35
Anyone know how quickly the spots filled up for the Orion when the GB started?
If I remember correctly the first 30 were gone within the first couple hours
That's actually not that quickly if you think about it. As long as you're prepared for the buy you should have plenty of time to get in.
Post by: romevi on Sun, 06 December 2015, 21:42:59
Anyone know how quickly the spots filled up for the Orion when the GB started?
If I remember correctly the first 30 were gone within the first couple hours
That's actually not that quickly if you think about it. As long as you're prepared for the buy you should have plenty of time to get in.
Phew. I didn't think that was fast either. The first round of Jane sold out within the day, and that was a while.
The second sold out in less than a half-hour, though!
Post by: trenzafeeds on Sun, 06 December 2015, 21:43:51
The second sold out in less than a half-hour, though!
Yeah, and I was at work lol :( luckily I'm buying one though :thumb:
Post by: Pemdas on Sun, 06 December 2015, 21:51:58
The second sold out in less than a half-hour, though!
Yeah, and I was at work lol :( luckily I'm buying one though :thumb:
Luckyyy. I sat refreshing the group buy page for like 6 hours. Took a small break to play fallout and of course that's the exact moment the buy gets approved :'(
Post by: E3E on Sun, 06 December 2015, 22:06:47
Post by: ika on Sun, 06 December 2015, 23:04:46
Anyone know how quickly the spots filled up for the Orion when the GB started?
If I remember correctly the first 30 were gone within the first couple hours
That's actually not that quickly if you think about it. As long as you're prepared for the buy you should have plenty of time to get in.
It's not like you can predict when GB threads pop up, though. AFAIK they need to be approved by mods and that basically happens whenever. "being prepared" = sit at your computer and F5 every five minutes? the thread notification emails can be hours late.
Post by: rainb1ood on Sun, 06 December 2015, 23:08:29
(http://images.tapatalk-cdn.com/15/12/06/49fea80b1c7791707d0f2b5e9143a9b7.jpg)
(http://images.tapatalk-cdn.com/15/12/06/29cd05a0663beddadbdaa5ac29e3bb5c.jpg)
(http://images.tapatalk-cdn.com/15/12/06/d8ceb09b834b3d49eab282a8d9b5bf34.jpg)
Assembled by E3E.
Post by: PrpnNightmare on Sun, 06 December 2015, 23:09:12
Anyone know how quickly the spots filled up for the Orion when the GB started?
If I remember correctly the first 30 were gone within the first couple hours
That's actually not that quickly if you think about it. As long as you're prepared for the buy you should have plenty of time to get in.
It's not like you can predict when GB threads pop up, though. AFAIK they need to be approved by mods and that basically happens whenever. "being prepared" = sit at your computer and F5 every five minutes? the thread notification emails can be hours late.
I have lost a lot of artisans to this, haha
Post by: E3E on Sun, 06 December 2015, 23:11:47
Anyone know how quickly the spots filled up for the Orion when the GB started?
If I remember correctly the first 30 were gone within the first couple hours
That's actually not that quickly if you think about it. As long as you're prepared for the buy you should have plenty of time to get in.
It's not like you can predict when GB threads pop up, though. AFAIK they need to be approved by mods and that basically happens whenever. "being prepared" = sit at your computer and F5 every five minutes? the thread notification emails can be hours late.
Welp, I'm sure Elton can give us a time to expect the GB to land on our shores, so that'll be time to camp out. Though I think everyone who wants one will probably be able to get one. I hope.
Post by: alienman82 on Sun, 06 December 2015, 23:12:57
Took some photos today.Show Image(http://images.tapatalk-cdn.com/15/12/06/49fea80b1c7791707d0f2b5e9143a9b7.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/29cd05a0663beddadbdaa5ac29e3bb5c.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/d8ceb09b834b3d49eab282a8d9b5bf34.jpg)
Assembled by E3E.
Is this jtk mixed with OG cherry
Post by: rainb1ood on Sun, 06 December 2015, 23:16:35
OG cherry with tsangan kit from SP from a GB years ago. I need a proper tsangan kit!Took some photos today.Show Image(http://images.tapatalk-cdn.com/15/12/06/49fea80b1c7791707d0f2b5e9143a9b7.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/29cd05a0663beddadbdaa5ac29e3bb5c.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/d8ceb09b834b3d49eab282a8d9b5bf34.jpg)
Assembled by E3E.
Is this jtk mixed with OG cherry
Post by: alienman82 on Sun, 06 December 2015, 23:31:25
OG cherry with tsangan kit from SP from a GB years ago. I need a proper tsangan kit!Took some photos today.Show Image(http://images.tapatalk-cdn.com/15/12/06/49fea80b1c7791707d0f2b5e9143a9b7.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/29cd05a0663beddadbdaa5ac29e3bb5c.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/d8ceb09b834b3d49eab282a8d9b5bf34.jpg)
Assembled by E3E.
Is this jtk mixed with OG cherry
Oh looks great!
Post by: trenzafeeds on Mon, 07 December 2015, 00:55:56
OG cherry with tsangan kit from SP from a GB years ago. I need a proper tsangan kit!Took some photos today.Show Image(http://images.tapatalk-cdn.com/15/12/06/49fea80b1c7791707d0f2b5e9143a9b7.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/29cd05a0663beddadbdaa5ac29e3bb5c.jpg)Show Image(http://images.tapatalk-cdn.com/15/12/06/d8ceb09b834b3d49eab282a8d9b5bf34.jpg)
Assembled by E3E.
Is this jtk mixed with OG cherry
A JTK set would definitely be your best bet as a tsangan kit I think. Bunny still has some if you PM him.
Post by: orcinus on Mon, 07 December 2015, 10:00:06
If I remember correctly the first 30 were gone within the first couple hours
I placed my order like an hour and a half after and got spot 23
I jumped in 5.5 hours after the thread start and ended up #39.
Post by: Want on Mon, 07 December 2015, 11:17:36
As the holidays are creeping up, I feel like more updates would soothe my nerves.
I also realize that elton is sort of a middle man here and might have trouble getting the info, so of course I take that into consideration.
Post by: E3E on Mon, 07 December 2015, 11:35:44
If I remember correctly the first 30 were gone within the first couple hours
I placed my order like an hour and a half after and got spot 23
I jumped in 5.5 hours after the thread start and ended up #39.
I just better make sure I'm free the day of the group buy, then there shouldn't be any problems. I'm glad 75% isn't as popular as TKL, so it's a little less pressure to boot. :)
Post by: appleonama on Tue, 08 December 2015, 14:15:30
Post by: elton5354 on Tue, 08 December 2015, 19:00:01
Post by: ccc24 on Tue, 08 December 2015, 19:27:21
No update yet. I usually don't post anything if I don't have anything new..as for the start of GH's Oct. V2 GB, I may post it up over the weekend or once the 2nd batch are shipped. I still need some confirmation first.
Sound good. Prepare your wallets.
Post by: E3E on Tue, 08 December 2015, 20:24:35
No update yet. I usually don't post anything if I don't have anything new..as for the start of GH's Oct. V2 GB, I may post it up over the weekend or once the 2nd batch are shipped. I still need some confirmation first.
No update yet. I usually don't post anything if I don't have anything new..as for the start of GH's Oct. V2 GB, I may post it up over the weekend or once the 2nd batch are shipped. I still need some confirmation first.
Sound good. Prepare your wallets.
I'm down, yo. I am SO down. I'll be ready. :thumb:
Post by: Frizer on Wed, 09 December 2015, 10:33:29
No update yet. I usually don't post anything if I don't have anything new..as for the start of GH's Oct. V2 GB, I may post it up over the weekend or once the 2nd batch are shipped. I still need some confirmation first.
Thanks for keeping us in the loop, even if it's not much info it is appreciated.
Post by: filphil on Sat, 12 December 2015, 23:25:21
(http://i.imgur.com/b1owP6Q.jpg)
(http://i.imgur.com/BRSezF6.jpg)
Post by: Steezus on Sat, 12 December 2015, 23:28:58
I haven't posted anything keyboard related in a while so...Show Image(http://i.imgur.com/b1owP6Q.jpg)Show Image(http://i.imgur.com/BRSezF6.jpg)
Beautiful board filphil, I really like the beige without in switch LEDs. :thumb:
The Orion blue grey is very different to the Jane's.
Post by: Pemdas on Sat, 12 December 2015, 23:35:10
I haven't posted anything keyboard related in a while so...Show Image(http://i.imgur.com/b1owP6Q.jpg)Show Image(http://i.imgur.com/BRSezF6.jpg)
Your pictures are like torture for those of us that haven't received theirs yet :p
Quick question. The lighting showing on the keys is that bleeding over from the side LEDs? Or do you have a few LEDs on certain keys?
Post by: Steezus on Sat, 12 December 2015, 23:37:18
I haven't posted anything keyboard related in a while so...Show Image(http://i.imgur.com/b1owP6Q.jpg)Show Image(http://i.imgur.com/BRSezF6.jpg)
Your pictures are like torture for those of us that haven't received theirs yet :p
Quick question. The lighting showing on the keys is that bleeding over from the side LEDs? Or do you have a few LEDs on certain keys?
That's light bleeding from the RGB LEDs, with a plastic plate there will be a little bit of light bleed. I noticed that on my Orion as well, even for the LED layer indicators.
Post by: filphil on Sat, 12 December 2015, 23:58:07
I haven't posted anything keyboard related in a while so...Show Image(http://i.imgur.com/b1owP6Q.jpg)Show Image(http://i.imgur.com/BRSezF6.jpg)
Your pictures are like torture for those of us that haven't received theirs yet :p
Quick question. The lighting showing on the keys is that bleeding over from the side LEDs? Or do you have a few LEDs on certain keys?
=D
What you're seeing is light bleed for sure. The plastic plate/aluminum bottom duo has some intense light bleed compared to an aluminum plate/acrylic flat bottom.
I'm sure once the in-switch leds are installed it'll nullify it but in the meantime I really dig it. The color looks whitish blue because of how long the exposure was taken.
Post by: ocodo on Tue, 15 December 2015, 18:08:43
I really want to buy a winkey/MX version (preferably with the full Alu case)
Post by: slushi on Tue, 15 December 2015, 23:33:42
If anyone is thinking about dropping their order, let me know.Join the club. I have an order but would love to get a second one with an aluminum bottom
I really want to buy a winkey/MX version (preferably with the full Alu case)
Post by: HannahPeach on Wed, 16 December 2015, 06:16:47
Post by: popkorn62 on Wed, 16 December 2015, 20:16:42
Post by: Pemdas on Wed, 16 December 2015, 20:23:36
:'(
Post by: ocodo on Wed, 16 December 2015, 20:26:15
Post by: alienman82 on Wed, 16 December 2015, 20:46:52
Gah I keep seeing this thread getting bumped and my heart jumps thinking there's an update everytime.
:'(
I know. Want it so bad have all the parts too....
Post by: Rainbow_ on Wed, 16 December 2015, 22:16:46
Post by: appleonama on Thu, 17 December 2015, 00:40:23
same im tired of waitingGah I keep seeing this thread getting bumped and my heart jumps thinking there's an update everytime.
:'(
I know. Want it so bad have all the parts too....
Post by: alienman82 on Thu, 17 December 2015, 00:53:02
same im tired of waitingGah I keep seeing this thread getting bumped and my heart jumps thinking there's an update everytime.
:'(
I know. Want it so bad have all the parts too....
is that why you make fire?
Post by: appleonama on Thu, 17 December 2015, 01:35:40
same im tired of waitingGah I keep seeing this thread getting bumped and my heart jumps thinking there's an update everytime.
:'(
I know. Want it so bad have all the parts too....
is that why you make fire?
of course I got to let it out some how
Post by: appleonama on Sun, 20 December 2015, 01:46:40
Post by: alienman82 on Sun, 20 December 2015, 09:05:04
:llama:
Ahh! Please just arrive! The horse is kicking me!
Post by: missalaire on Mon, 21 December 2015, 12:25:24
Post by: appleonama on Mon, 21 December 2015, 19:10:23
Post by: alienman82 on Mon, 21 December 2015, 21:02:44
:llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
jesus ****!
Post by: appleonama on Mon, 21 December 2015, 21:05:01
:llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
jesus ****!
you thought it was an update :p
Post by: E3E on Mon, 21 December 2015, 21:11:49
:llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
jesus ****!
you thought it was an update :p
BUT IT WAS ME :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
Post by: alienman82 on Mon, 21 December 2015, 22:08:20
:llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
jesus ****!
you thought it was an update :p
BUT IT WAS ME :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
why not?
:llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama: :llama:
Post by: ika on Mon, 21 December 2015, 23:43:44
(https://elaineandjosh.files.wordpress.com/2010/05/1zvbaxe2.gif)
Post by: elton5354 on Tue, 22 December 2015, 09:49:57
Post by: Frizer on Tue, 22 December 2015, 10:07:22
Post by: alienman82 on Tue, 22 December 2015, 11:12:37
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hell yeah. Appleonama can stop now!
Post by: appleonama on Tue, 22 December 2015, 11:30:31
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hell yeah. Appleonama can stop now!
FINALLY ! I CAN START PUTTING SIP SOCKETS ON MY SWITCHES
BURN ONE MORE CLACK IN CELEBRATION?
(http://i.imgur.com/3BNua6Q.jpg)
Post by: asdfjkl36 on Tue, 22 December 2015, 11:36:07
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hell yeah. Appleonama can stop now!
FINALLY ! I CAN START PUTTING SIP SOCKETS ON MY SWITCHES
BURN ONE MORE CLACK IN CELEBRATION?Show Image(http://i.imgur.com/3BNua6Q.jpg)
Why not just send them to me and let me burn them with my love
Post by: Steezus on Tue, 22 December 2015, 11:37:39
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hell yeah. Appleonama can stop now!
FINALLY ! I CAN START PUTTING SIP SOCKETS ON MY SWITCHES
BURN ONE MORE CLACK IN CELEBRATION?Show Image(http://i.imgur.com/3BNua6Q.jpg)
Here I am sitting here clackless while appleonama is burning them all...
Edit: messed up the damn quotes
Post by: appleonama on Tue, 22 December 2015, 11:43:14
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hell yeah. Appleonama can stop now!
FINALLY ! I CAN START PUTTING SIP SOCKETS ON MY SWITCHES
BURN ONE MORE CLACK IN CELEBRATION?Show Image(http://i.imgur.com/3BNua6Q.jpg)
Why not just send them to me and let me burn them with my love
send me your clacks first
Post by: E3E on Tue, 22 December 2015, 14:08:35
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
Hell yeah. Appleonama can stop now!
FINALLY ! I CAN START PUTTING SIP SOCKETS ON MY SWITCHES
BURN ONE MORE CLACK IN CELEBRATION?Show Image(http://i.imgur.com/3BNua6Q.jpg)
You seriously have to be making replicas and the burning them, right? I can't imagine anyone would take a knife to a $100 or more.
Unless they're the cloned clacks. K3KC or something?
Again, if you seriously do murder your Clacks, then you are a verifiable cap serial killer! xD
Post by: Pemdas on Tue, 22 December 2015, 15:17:07
Hey guys. Good news! Finally the rest of the orders are packed and ready to be picked up tomorrow (tonight if you're in NA). I'll get the tracking up in the list once I get them. Probably won't get it by Christmas though....:(
:thumb: :thumb: :thumb: :thumb: :thumb:
So excited, thanks for the update elton.
Post by: aznairjordan on Tue, 22 December 2015, 16:52:35
Post by: PrpnNightmare on Tue, 22 December 2015, 17:24:12
Post by: E3E on Tue, 22 December 2015, 17:29:04
So does that mean Octagon V2 is on its way soon? If I miss that GB I will burn a lot more than some clacks..
Elton mentioned it will be occurring some time in January! Stay tuned! :thumb:
Post by: ctrlX on Wed, 23 December 2015, 00:29:09
Post by: elton5354 on Wed, 23 December 2015, 18:50:25
This is for the remaining orders in the first round right?
These are for the rest of the orders that hasn't been shipped yet.
Trackings #s are up now except for one that needed to be shipped domestically to another Korean member.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
Post by: appleonama on Wed, 23 December 2015, 19:01:40
This is for the remaining orders in the first round right?
These are for the rest of the orders that hasn't been shipped yet.
Trackings #s are up now except for one that needed to be shipped domestically to another Korean member.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
:thumb:
awesome
Post by: ryptide11 on Thu, 24 December 2015, 01:01:26
Post by: ctrlX on Thu, 24 December 2015, 01:01:29
Post by: concertomi on Thu, 24 December 2015, 02:46:16
Post by: pmh1410 on Thu, 24 December 2015, 07:19:56
This is for the remaining orders in the first round right?
These are for the rest of the orders that hasn't been shipped yet.
Trackings #s are up now except for one that needed to be shipped domestically to another Korean member.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
:thumb:
awesome
Many thanks Elton for update ;)
Post by: slushi on Thu, 24 December 2015, 11:43:45
Edit: I bought my order from FrostyToast and I believe we sent you my address for the change. I noticed Frosty lives in Canada so I wonder if it got shipped to him?
Post by: Pemdas on Thu, 24 December 2015, 19:23:09
This is for the remaining orders in the first round right?
These are for the rest of the orders that hasn't been shipped yet.
Trackings #s are up now except for one that needed to be shipped domestically to another Korean member.
https://docs.google.com/spreadsheets/d/1jrMbDe35hC3IshgaSnp90YyeR8AT3GJw1ozidWtn4qQ/pubhtml?gid=702353801&single=true
Tracking numbers yes! Thanks again elton can't wait 'til next year now :thumb: :thumb:
Post by: appleonama on Fri, 25 December 2015, 12:44:13
LOS ANGELES
might get mine sometime next week :cool:
Post by: alienman82 on Fri, 25 December 2015, 13:33:23
Delivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
Post by: R1N3 on Fri, 25 December 2015, 13:47:56
Post by: Steezus on Fri, 25 December 2015, 15:05:26
Delivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Post by: alienman82 on Fri, 25 December 2015, 15:12:53
Delivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
Post by: appleonama on Fri, 25 December 2015, 15:33:31
Delivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
can't wait to break out my full frame for this glorious board. hyperfuse, purple clack
Post by: alienman82 on Fri, 25 December 2015, 15:40:34
Delivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
can't wait to break out my full frame for this glorious board. hyperfuse, purple clack
I have a full frame, and 2 purple clacks, just at other address :( Hyperfuse is meh
Post by: appleonama on Fri, 25 December 2015, 17:17:39
what keyset are you usingDelivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
can't wait to break out my full frame for this glorious board. hyperfuse, purple clack
I have a full frame, and 2 purple clacks, just at other address :( Hyperfuse is meh
Post by: alienman82 on Fri, 25 December 2015, 17:28:49
what keyset are you usingDelivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
can't wait to break out my full frame for this glorious board. hyperfuse, purple clack
I have a full frame, and 2 purple clacks, just at other address :( Hyperfuse is meh
SGi caps for my alps pcb :p For the mx one, I'll use OG cherry or OG Dolch with GMK mods, or OG wob with GMK mods.
Post by: Steezus on Fri, 25 December 2015, 17:40:31
what keyset are you usingDelivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
can't wait to break out my full frame for this glorious board. hyperfuse, purple clack
I have a full frame, and 2 purple clacks, just at other address :( Hyperfuse is meh
SGi caps for my alps pcb :p For the mx one, I'll use OG cherry or OG Dolch with GMK mods, or OG wob with GMK mods.
Good choice, I've been wanting to grab a set of OG caps. I currently having the OTD Red Alert on mine, first time ever using DCS and I'm actually quite fond of it. My original plan was to the GMK Hyperfuse set and the three matching Boopers that I have, but I'm still waiting to get my hyperfuse set in the mail.
Post by: alienman82 on Fri, 25 December 2015, 17:47:33
what keyset are you usingDelivered to Destination AirportKorea Post
LOS ANGELES
might get mine sometime next week :cool:
mine is in Delaware OuO
So close but yet so far. :(
I can't wait until you get the board and upload some shots, I'm curious as to what everybody is planning for their Orion v2. :thumb:
Thanks! Only got the point and shoot right now, but it'll do
can't wait to break out my full frame for this glorious board. hyperfuse, purple clack
I have a full frame, and 2 purple clacks, just at other address :( Hyperfuse is meh
SGi caps for my alps pcb :p For the mx one, I'll use OG cherry or OG Dolch with GMK mods, or OG wob with GMK mods.
Good choice, I've been wanting to grab a set of OG caps. I currently having the OTD Red Alert on mine, first time ever using DCS and I'm actually quite fond of it. My original plan was to the GMK Hyperfuse set and the three matching Boopers that I have, but I'm still waiting to get my hyperfuse set in the mail.
Wish I liked DCS, sold soware since I didn't care for the feel. Lot of good looking DCS sets out there. I do like SA though. Have yet to try DSA.
Post by: appleonama on Sat, 26 December 2015, 09:10:32
^-^
Post by: alienman82 on Sat, 26 December 2015, 09:54:06
Expected Delivery Day: Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
Post by: aznairjordan on Sat, 26 December 2015, 10:04:38
Expected Delivery Day: Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
When did yours ship out? Mine just got on a plane in the 24th
Post by: alienman82 on Sat, 26 December 2015, 10:13:27
Expected Delivery Day: Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
When did yours ship out? Mine just got on a plane in the 24th
23rd at 8:30PM just got delivered. Opening soon
Post by: Steezus on Sat, 26 December 2015, 10:15:47
Expected Delivery Day: Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
When did yours ship out? Mine just got on a plane in the 24th
23rd at 8:30PM just got delivered. Opening soon
Very exciting! Perfect day to receive the board to give you plenty of time to build it. I don't think there has been one board yet that I haven't built the same day as the kit arriving.
Post by: aznairjordan on Sat, 26 December 2015, 10:17:35
Oh **** now mine is coming on the 29th!!Expected Delivery Day:Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
When did yours ship out? Mine just got on a plane in the 24th
23rd at 8:30PM just got delivered. Opening soon
Post by: appleonama on Sat, 26 December 2015, 10:17:44
Expected Delivery Day: Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
wow that sucks you get yours before i do >:D
Post by: alienman82 on Sat, 26 December 2015, 10:50:49
Expected Delivery Day: Tuesday, December 29, 2015
^-^
Mine is at local post office !!!!
wow that sucks you get yours before i do >:D
(http://imgur.com/fl3bNMS.jpg)
Post by: Pemdas on Sat, 26 December 2015, 18:06:17
Show Image(http://imgur.com/fl3bNMS.jpg)
You got yours already?!?! ems shipping is fast!
Post by: alienman82 on Sat, 26 December 2015, 18:31:52
Post by: ika on Sun, 27 December 2015, 03:24:03
Post by: ctrlX on Mon, 28 December 2015, 07:23:07
Status: Unsuccessful delivery
Nooooooo! WTH! >:D >:D >:D >:D
Post by: nguyenkimtam on Mon, 28 December 2015, 08:01:13
Poor you, what's wrong with this ?
Status: Unsuccessful delivery
Nooooooo! WTH! >:D >:D >:D >:D
Post by: ctrlX on Mon, 28 December 2015, 08:28:53
That was the status of my tracking no. Reason was blank so no reason was given as to why the delivery was unsuccessful.Poor you, what's wrong with this ?
Status: Unsuccessful delivery
Nooooooo! WTH! >:D >:D >:D >:D
Luckely enough I just got home and a delivery notice was left in my mailbox. The package is waiting on me at the post office :-)
I got worried the package was misplaced or similar. I've been very unlucky with packages lately.
Post by: nguyenkimtam on Mon, 28 December 2015, 09:10:45
Congratulation :thumb: :thumb:That was the status of my tracking no. Reason was blank so no reason was given as to why the delivery was unsuccessful.Poor you, what's wrong with this ?
Status: Unsuccessful delivery
Nooooooo! WTH! >:D >:D >:D >:D
Luckely enough I just got home and a delivery notice was left in my mailbox. The package is waiting on me at the post office :-)
I got worried the package was misplaced or similar. I've been very unlucky with packages lately.
I'm waiting this package , maybe will receive this week. Then maybe sell it haha
Post by: appleonama on Mon, 28 December 2015, 13:54:42
getting this awesome board tomorrow and on wednesday I am also getting a GON TKL. 2 sexy boards in one week :cool:
Post by: alienman82 on Mon, 28 December 2015, 13:55:10
Post by: appleonama on Mon, 28 December 2015, 14:07:28
I'm getting my solder tomorrowhope you got that kester butter solder
Post by: alienman82 on Mon, 28 December 2015, 14:08:14
I'm getting my solder tomorrowhope you got that kester butter solder
I did. Plus OG weller tips and flux
Post by: Pemdas on Mon, 28 December 2015, 14:24:21
Even got it a day earlier than the expected ship date :cool:
(http://i.imgur.com/U5dZ7oh.jpg)
I was so excited to put this together while I was expecting it, but now that it's in my hands I'm kinda nervous about assembling it haha
Once again many thanks to Elton and here's hoping the Octagon V2 buy comes soon :thumb:
Post by: alienman82 on Mon, 28 December 2015, 14:25:32
Got it! I think this keyboard was speaking to me, I woke up just in time to hear USPS drive up to my door and I opened the door as the postman was putting the missed you slip on my door. :eek:
Even got it a day earlier than the expected ship date :cool:Show Image(http://i.imgur.com/U5dZ7oh.jpg)
I was so excited to put this together while I was expecting it, but now that it's in my hands I'm kinda nervous about assembling it haha
Once again many thanks to Elton and here's hoping the Octagon V2 buy comes soon :thumb:
Have kinda glad I waited to order the new solder. Patience is important and that old stuff I had is ****
Post by: appleonama on Mon, 28 December 2015, 14:31:00
Post by: Pemdas on Mon, 28 December 2015, 16:14:50
I'm getting my solder tomorrowhope you got that kester butter solder
I did. Plus OG weller tips and flux
Did you get rosin free solder? If you got the kester that everyone uses (kester 44 represent!) it has a rosin core that eliminates the need for flux AFAIK.
I'm gonna try and get my board finished tonight, thankfully I don't have any work tomorrow so I can work through the night :p
Also, ~7 months of waiting and I wait til the day I get the keyboard to put in sip sockets... I hate my procrastinating ways.
Post by: filphil on Mon, 28 December 2015, 16:48:32
I'm getting my solder tomorrowhope you got that kester butter solder
I did. Plus OG weller tips and flux
Did you get rosin free solder? If you got the kester that everyone uses (kester 44 represent!) it has a rosin core that eliminates the need for flux AFAIK.
I'm gonna try and get my board finished tonight, thankfully I don't have any work tomorrow so I can work through the night :p
Also, ~7 months of waiting and I wait til the day I get the keyboard to put in sip sockets... I hate my procrastinating ways.
You Should have done 1 switch a day. Would have made the wait a little easier!
Flux is always good to have on hand because you never know if you have to reflow a joint.
Post by: alienman82 on Mon, 28 December 2015, 16:50:29
I'm getting my solder tomorrowhope you got that kester butter solder
I did. Plus OG weller tips and flux
Did you get rosin free solder? If you got the kester that everyone uses (kester 44 represent!) it has a rosin core that eliminates the need for flux AFAIK.
I'm gonna try and get my board finished tonight, thankfully I don't have any work tomorrow so I can work through the night :p
Also, ~7 months of waiting and I wait til the day I get the keyboard to put in sip sockets... I hate my procrastinating ways.
You Should have done 1 switch a day. Would have made the wait a little easier!
Flux is always good to have on hand because you never know if you have to reflow a joint.
Yes I got rosin solder. Flux is extra :)
Post by: appleonama on Mon, 28 December 2015, 19:06:11
Same doing sip sockets atm before it arrives tomorrow. This process takes me about 2-4 hours man I hate it.I'm getting my solder tomorrowhope you got that kester butter solder
I did. Plus OG weller tips and flux
Did you get rosin free solder? If you got the kester that everyone uses (kester 44 represent!) it has a rosin core that eliminates the need for flux AFAIK.
I'm gonna try and get my board finished tonight, thankfully I don't have any work tomorrow so I can work through the night :p
Also, ~7 months of waiting and I wait til the day I get the keyboard to put in sip sockets... I hate my procrastinating ways.
Post by: appleonama on Mon, 28 December 2015, 20:53:39
Post by: Steezus on Mon, 28 December 2015, 20:58:38
6 switches lubed and sipped :)
Only around ~80 to go, depending on your layout :p
Post by: alienman82 on Mon, 28 December 2015, 21:05:57
Post by: orcinus on Mon, 28 December 2015, 22:49:52
Last status was on departure from Korea, on 24th.
Since then, no updates.
And yes, i've checked my local post's tracking too. Same info.
How long did shipping take for you folks?
Post by: alienman82 on Mon, 28 December 2015, 22:50:36
Post by: Pemdas on Mon, 28 December 2015, 23:20:26
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.
(http://i.imgur.com/Zfr4c7l.png)
(http://i.imgur.com/Uf627Zj.png)
(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Post by: Steezus on Mon, 28 December 2015, 23:24:39
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Very nice! I see you sip-socketed your switches but didn't add LEDs, how come?
Post by: Pemdas on Mon, 28 December 2015, 23:32:31
Very nice! I see you sip-socketed your switches but didn't add LEDs, how come?
Thanks! Can finally join the kustom club ;D
I prefer keyboards with no backlight usually. I think out of the 10 keyboards I own only 1 has full backlighting. With that said I put in sip sockets because I like having the option to go full out with the lighting if the mood hits me. Better to put them in now than desoldering the board and putting them in later :p
Post by: alienman82 on Mon, 28 December 2015, 23:53:11
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
sweet man! Just made me realize I need to get order a usb cable :))
Post by: Steezus on Mon, 28 December 2015, 23:56:16
Very nice! I see you sip-socketed your switches but didn't add LEDs, how come?
Thanks! Can finally join the kustom club ;D
I prefer keyboards with no backlight usually. I think out of the 10 keyboards I own only 1 has full backlighting. With that said I put in sip sockets because I like having the option to go full out with the lighting if the mood hits me. Better to put them in now than desoldering the board and putting them in later :p
Yeah sip-socketing is always a good idea even if you don't like backlighting it helps if you ever need to sell the board. I love backlighting myself so I, the Orion v2 is meant to light like the sun. :p
Post by: E3E on Tue, 29 December 2015, 00:11:27
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Glorious, simply glorious. I love the way the RGB shines up through the Zealios.
Hotswapping is always a good option, even if you never use the functionality yourself. Whether it's for switches or LEDs. I've SIP socketed ALL of my MX boards and it's very nice to switch up the colors at will if needed.
Oooh, that aluminum on aluminum though. I CANNOT wait for the Octagon v2, where I'll finally pick a more subtle color as opposed to my overall favorite case color, red. It's super hard to find a set that really gels well with a red case, but it's hard to pass up that fiery hue. Ahh, so good.
This time I'm going to go for silver top and blue grey bottom! :thumb:
Did you end up getting two different bottom halves, or do you have TWO Orion v2s? :O
Post by: filphil on Tue, 29 December 2015, 00:32:45
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Glorious, simply glorious. I love the way the RGB shines up through the Zealios.
Hotswapping is always a good option, even if you never use the functionality yourself. Whether it's for switches or LEDs. I've SIP socketed ALL of my MX boards and it's very nice to switch up the colors at will if needed.
Oooh, that aluminum on aluminum though. I CANNOT wait for the Octagon v2, where I'll finally pick a more subtle color as opposed to my overall favorite case color, red. It's super hard to find a set that really gels well with a red case, but it's hard to pass up that fiery hue. Ahh, so good.
This time I'm going to go for silver top and blue grey bottom! :thumb:
Did you end up getting two different bottom halves, or do you have TWO Orion v2s? :O
If you're wondering if it's possible to have two different colored halves for a single order when you go for the octagon then yes you should be able to do that. My orders were like that and they came out perfectly. I say should because you never know if duck will change that option in the future.
Post by: E3E on Tue, 29 December 2015, 01:00:26
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Glorious, simply glorious. I love the way the RGB shines up through the Zealios.
Hotswapping is always a good option, even if you never use the functionality yourself. Whether it's for switches or LEDs. I've SIP socketed ALL of my MX boards and it's very nice to switch up the colors at will if needed.
Oooh, that aluminum on aluminum though. I CANNOT wait for the Octagon v2, where I'll finally pick a more subtle color as opposed to my overall favorite case color, red. It's super hard to find a set that really gels well with a red case, but it's hard to pass up that fiery hue. Ahh, so good.
This time I'm going to go for silver top and blue grey bottom! :thumb:
Did you end up getting two different bottom halves, or do you have TWO Orion v2s? :O
If you're wondering if it's possible to have two different colored halves for a single order when you go for the octagon then yes you should be able to do that. My orders were like that and they came out perfectly. I say should because you never know if duck will change that option in the future.
Oh no, I was asking more so whether or not he bought a few different lowers or actually bought two different Orions to go with the angled acrylic bottom and the aluminum bottom in his imgur album.
Yeah, I'm expecting Duck to leave that option open, especially considering how he had some renders of the Octagon v2 with dual tone color schemes.
Post by: orcinus on Tue, 29 December 2015, 01:19:51
3 including Christmas day
Well that's mildly worrying, then.
Fingers crossed someone just forgot to update tracking data and it's on its way.
Post by: Pemdas on Tue, 29 December 2015, 01:48:21
sweet man! Just made me realize I need to get order a usb cable :))
I still need to order a new cable that's just for the Orion too!
Yeah sip-socketing is always a good idea even if you don't like backlighting it helps if you ever need to sell the board. I love backlighting myself so I, the Orion v2 is meant to light like the sun. :p
I'm probably gonna light this one up sooner or later, with the acrylic back I'll be able to use this as a flashlight :))
Well that's mildly worrying, then.
Fingers crossed someone just forgot to update tracking data and it's on its way.
I've had so many packages just show up without updated tracking, hopefully you get yours with no problems!
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Glorious, simply glorious. I love the way the RGB shines up through the Zealios.
Hotswapping is always a good option, even if you never use the functionality yourself. Whether it's for switches or LEDs. I've SIP socketed ALL of my MX boards and it's very nice to switch up the colors at will if needed.
Oooh, that aluminum on aluminum though. I CANNOT wait for the Octagon v2, where I'll finally pick a more subtle color as opposed to my overall favorite case color, red. It's super hard to find a set that really gels well with a red case, but it's hard to pass up that fiery hue. Ahh, so good.
This time I'm going to go for silver top and blue grey bottom! :thumb:
Did you end up getting two different bottom halves, or do you have TWO Orion v2s? :O
If you're wondering if it's possible to have two different colored halves for a single order when you go for the octagon then yes you should be able to do that. My orders were like that and they came out perfectly. I say should because you never know if duck will change that option in the future.
Oh no, I was asking more so whether or not he bought a few different lowers or actually bought two different Orions to go with the angled acrylic bottom and the aluminum bottom in his imgur album.
Yeah, I'm expecting Duck to leave that option open, especially considering how he had some renders of the Octagon v2 with dual tone color schemes.
I just got one Orion with 2 backs. The silver bottom and acrylic angled bottom, and now that I've seen the pictures I'm kicking myself for not getting the flat acrylic bottom it was so cheap....
And go red again! You have the Jukebox set you're set for life on keysets that look good on red keyboards :p I want to get a "out there" color for my next one. Like a pink or purple.
Post by: slickmamba on Tue, 29 December 2015, 02:01:50
6 switches lubed and sipped :)
just did 90 zealios today... not for orion though. took a good 3 hours to take apart, lube, SIP socket.
Post by: ramnes on Tue, 29 December 2015, 02:57:11
Show Image(http://i.imgur.com/Zfr4c7l.png)
phat
Post by: filphil on Tue, 29 December 2015, 07:29:57
Post by: appleonama on Tue, 29 December 2015, 08:20:55
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!i just got off to this amazing we got the same config
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Post by: Pemdas on Tue, 29 December 2015, 08:53:57
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!i just got off to this amazing we got the same config
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Twinsies?
Post by: xondat on Tue, 29 December 2015, 09:02:27
8 months 17 days from placing my order, I now have a working Orion V2 in my hands! What a journey!
Definitely worth the wait! Haven't fiddled around with the keymapping yet (gonna start now) but got it all assembled!
I used 65g tactile Zealios only had 4 switches with the chattering problem but got them fixed up no problem.Show Image(http://i.imgur.com/Zfr4c7l.png)Show Image(http://i.imgur.com/Uf627Zj.png)Show Image(http://i.imgur.com/qMlQGFN.png)
All in all VERY satisfied with the board! Loving the blue and silver combo too glad I switched over from black :cool:
Thanks Elton and Duck and anyone else invovled :thumb: :thumb: :thumb:
And a link to some more pictures I took during the build if anyone is interested ;)
http://imgur.com/a/3xiK2
Congratulations! That is as great looking boards, and I especially love the look of the LEDs with the clear switch tops.
Post by: appleonama on Tue, 29 December 2015, 11:06:56
Post by: alienman82 on Tue, 29 December 2015, 11:07:20
it here! but I am still not done with my switches... I fell asleep yesterday
Pics or it didn't happen
Post by: elton5354 on Tue, 29 December 2015, 13:40:34
(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
Post by: alienman82 on Tue, 29 December 2015, 13:46:20
Why couldnt leekus pcb have diodes preinstalled....Show Image(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
I feel you
Post by: E3E on Tue, 29 December 2015, 15:06:46
Why couldnt leekus pcb have diodes preinstalled....Show Image(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
To make you cherish the board even more once you're done, of course! :thumb:
/me makes a note to buy diodes
Post by: Steezus on Tue, 29 December 2015, 16:22:25
Why couldnt leekus pcb have diodes preinstalled....Show Image(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
To make you cherish the board even more once you're done, of course! :thumb:
/me makes a note to buy diodes
Diodes and resistor are a pain, I much prefer spending the extra money to have somebody do them for me. I wish Duck came out with an Alps option, I like his firmware better.
Post by: alienman82 on Tue, 29 December 2015, 17:14:46
Why couldnt leekus pcb have diodes preinstalled....Show Image(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
To make you cherish the board even more once you're done, of course! :thumb:
/me makes a note to buy diodes
Diodes and resistor are a pain, I much prefer spending the extra money to have somebody do them for me. I wish Duck came out with an Alps option, I like his firmware better.
even more of a pain when they aren't included! AHHH more waiting ! DAMN IT
Post by: appleonama on Tue, 29 December 2015, 18:07:37
Post by: alienman82 on Tue, 29 December 2015, 18:08:31
I forgot how stabs go on :rolleyes: anyone can teach me ?
Bigger holes are for the stationary part, slide them in, then out the clip ends in the smaller holes
Post by: E3E on Tue, 29 December 2015, 18:17:07
Why couldnt leekus pcb have diodes preinstalled....Show Image(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
To make you cherish the board even more once you're done, of course! :thumb:
/me makes a note to buy diodes
Diodes and resistor are a pain, I much prefer spending the extra money to have somebody do them for me. I wish Duck came out with an Alps option, I like his firmware better.
Hehe, I've got a potential Alps Orion v2 build lined up for Slushi so I have to be prepared, but SMD isn't so bad!
Post by: orcinus on Tue, 29 December 2015, 19:43:52
All it takes is solder with good flux and tweezers.
Still no updates on my tracking T_T
Post by: Steezus on Tue, 29 December 2015, 19:46:42
Why couldnt leekus pcb have diodes preinstalled....Show Image(https://uploads.tapatalk-cdn.com/20151229/fbe27f377b9c3e31f1d398f85cc0f3a5.jpg)
To make you cherish the board even more once you're done, of course! :thumb:
/me makes a note to buy diodes
Diodes and resistor are a pain, I much prefer spending the extra money to have somebody do them for me. I wish Duck came out with an Alps option, I like his firmware better.
Hehe, I've got a potential Alps Orion v2 build lined up for Slushi so I have to be prepared, but SMD isn't so bad!
It's not difficult at all just tedious, it's relatively easy but having to solder a resistor, diode, LED, and then the switch itself for a TKL board takes quite the amount of time.
Post by: alienman82 on Tue, 29 December 2015, 19:53:35
Post by: orcinus on Tue, 29 December 2015, 20:46:35
I've done smd before just sucks that U have to wait for more parts
I hear ya.
Always sucks. I've been accumulating parts for a new (custom watercooling loop) rig for months now.
There's always some **** missing and i have to wait for it.
Post by: alienman82 on Tue, 29 December 2015, 20:47:27
I've done smd before just sucks that U have to wait for more parts
I hear ya.
Always sucks. I've been accumulating parts for a new (custom watercooling loop) rig for months now.
There's always some **** missing and i have to wait for it.
Yep, the waiting and cost is why I chose a h100i for my rig. Got it for $40 new reddit deal
Post by: appleonama on Wed, 30 December 2015, 14:26:44
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orion
(http://i.imgur.com/Jc2KQdc.jpg)
Post by: alienman82 on Wed, 30 December 2015, 14:36:09
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orion she is a lookerShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Img broken
Post by: appleonama on Wed, 30 December 2015, 14:37:38
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orion she is a lookerShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Img broken
http://imgur.com/Jc2KQdc
Post by: Pemdas on Wed, 30 December 2015, 14:51:42
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
Post by: appleonama on Wed, 30 December 2015, 14:59:23
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
Post by: Pemdas on Wed, 30 December 2015, 15:04:18
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
:eek: bizzare I haven't fiddled around with the software yet so wouldn't even know where to start
Post by: Steezus on Wed, 30 December 2015, 15:48:40
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
Have you tried de-soldering just that switch and seeing if the issue persists? I'm not really sure it could be the firmware after messing around with it a bit, or it could a defective PCB which I sure hope not.
Post by: appleonama on Wed, 30 December 2015, 19:18:17
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
Have you tried de-soldering just that switch and seeing if the issue persists? I'm not really sure it could be the firmware after messing around with it a bit, or it could a defective PCB which I sure hope not.
its the switch... once I remover solder from the joints it stopped the print screen. I wonder whats wrong with it. I can't take of the switch since my solder sucker sucks ass. just got this http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011 (http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011) if I kept trying id probably burn the bad off
Post by: Steezus on Wed, 30 December 2015, 19:25:14
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
Have you tried de-soldering just that switch and seeing if the issue persists? I'm not really sure it could be the firmware after messing around with it a bit, or it could a defective PCB which I sure hope not.
its the switch... once I remover solder from the joints it stopped the print screen. I wonder whats wrong with it. I can't take of the switch since my solder sucker sucks ass. just got this http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011 (http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011) if I kept trying id probably burn the bad off
Ah at least it's the switch. I have the same solder sucker as well, I find it best if you can not get suck up all the solder the first time to re-solder it, heat up the solder, and then try and get the best seal possible with the solder sucker and then hit the button to suck it up. Sometimes if you leave a little gap it won't completely suck up all the solder, I'm definitely going to invest in a de-soldering station one of these times.
Post by: appleonama on Wed, 30 December 2015, 19:43:15
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
Have you tried de-soldering just that switch and seeing if the issue persists? I'm not really sure it could be the firmware after messing around with it a bit, or it could a defective PCB which I sure hope not.
its the switch... once I remover solder from the joints it stopped the print screen. I wonder whats wrong with it. I can't take of the switch since my solder sucker sucks ass. just got this http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011 (http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011) if I kept trying id probably burn the bad off
Ah at least it's the switch. I have the same solder sucker as well, I find it best if you can not get suck up all the solder the first time to re-solder it, heat up the solder, and then try and get the best seal possible with the solder sucker and then hit the button to suck it up. Sometimes if you leave a little gap it won't completely suck up all the solder, I'm definitely going to invest in a de-soldering station one of these times.
burn the pad*
yeah thats good I can live without a print screen for the mean time. yeah I tried to resolder and suck it out but my sucker just sucks. I don't want to burn the pad :( I just remembered my friend has a soldering station! going to take it to him to remove the solder.
do you know how to access fn or the other layers?
Post by: Steezus on Wed, 30 December 2015, 20:05:03
MoreDONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Nice! The TA looks really good on that, makes me want to get a set haha
Are you using zealous by chance? I had a couple chattering issues that made the switches activate before actually going all the way down.
https://geekhack.org/index.php?topic=74807.msg1923515#msg1923515
Used this to fix it though. 100% success rate and didn't have to desolder anything :)
I am using gateron black but I inspected every single switch. I don't think it is a switch problem it seems to be a software issue. Everytime I connect my keyboards it just begins to prt sc multiple times
Have you tried de-soldering just that switch and seeing if the issue persists? I'm not really sure it could be the firmware after messing around with it a bit, or it could a defective PCB which I sure hope not.
its the switch... once I remover solder from the joints it stopped the print screen. I wonder whats wrong with it. I can't take of the switch since my solder sucker sucks ass. just got this http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011 (http://www.amazon.com/Engineer-SS-02-Solder-Sucker/dp/B002MJMXD4/ref=sr_1_3?dd=aKrOoZPHPFjYz6XKVlNrCg%2C%2C&ddc_refnmnt=pfod&ie=UTF8&qid=1451524284&sr=8-3&keywords=solder+sucker&refinements=p_97%3A11292772011) if I kept trying id probably burn the bad off
Ah at least it's the switch. I have the same solder sucker as well, I find it best if you can not get suck up all the solder the first time to re-solder it, heat up the solder, and then try and get the best seal possible with the solder sucker and then hit the button to suck it up. Sometimes if you leave a little gap it won't completely suck up all the solder, I'm definitely going to invest in a de-soldering station one of these times.
burn the pad*
yeah thats good I can live without a print screen for the mean time. yeah I tried to resolder and suck it out but my sucker just sucks. I don't want to burn the pad :( I just remembered my friend has a soldering station! going to take it to him to remove the solder.
do you know how to access fn or the other layers?
I'm pretty sure there is not a key to layer change or function(since I have wkl) with the preset hex file loaded onto the board. I ended up changing my Pause key to layer change and it makes it very easy to rotate thru the layers. I have my second layer set for the LED controls.
Post by: elton5354 on Wed, 30 December 2015, 22:29:26
Also the TA set looked ugly at first but now it is love at first sight on the orion
That's not how love at first sight works! :P
Post by: alienman82 on Wed, 30 December 2015, 22:34:57
Post by: elton5354 on Wed, 30 December 2015, 22:36:22
I wish my diodes could here faster
Sorry :( If i had known we need them beforehand, you wouldn't had to wait now.
Post by: appleonama on Wed, 30 December 2015, 22:37:25
Also the TA set looked ugly at first but now it is love at first sight on the orion
That's not how love at first sight works! :P
:rolleyes: got me there
You know its love at first sight for you :cool:
Post by: alienman82 on Wed, 30 December 2015, 22:38:42
I wish my diodes could here faster
Sorry :( If i had known we need them beforehand, you wouldn't had to wait now.
Not a problem. Appreciate what you did for me. Was very kind of you
Post by: appleonama on Wed, 30 December 2015, 23:00:14
PURDY
Post by: R1N3 on Wed, 30 December 2015, 23:25:11
We need diodes? ? ?I wish my diodes could here faster
Sorry :( If i had known we need them beforehand, you wouldn't had to wait now.
Post by: Steezus on Wed, 30 December 2015, 23:26:09
Show Image(http://i.imgur.com/gLe3SE9.jpg)
PURDY
Damn beautiful! I wish I was able to get my hands on the flat acrylic bottom, I'm sure a lot of people weren't expecting it to look this good. :thumb:
Post by: alienman82 on Wed, 30 December 2015, 23:28:33
We need diodes? ? ?I wish my diodes could here faster
Sorry :( If i had known we need them beforehand, you wouldn't had to wait now.
Only for alps
Post by: R1N3 on Wed, 30 December 2015, 23:29:25
Confirmed. Ty <3We need diodes? ? ?I wish my diodes could here faster
Sorry :( If i had known we need them beforehand, you wouldn't had to wait now.
Only for alps
Post by: appleonama on Wed, 30 December 2015, 23:36:48
Show Image(http://i.imgur.com/gLe3SE9.jpg)
PURDY
Damn beautiful! I wish I was able to get my hands on the flat acrylic bottom, I'm sure a lot of people weren't expecting it to look this good. :thumb:
yeah it looks great tbh I think I prefer the flat acrylic bottom than to the other bottoms.
Post by: Steezus on Thu, 31 December 2015, 00:41:40
(https://farm6.staticflickr.com/5793/23995949621_4ce521e4fe_z.jpg) (https://flic.kr/p/CyrvPk)
Orion v2 with Zealios (https://flic.kr/p/CyrvPk) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
(https://farm2.staticflickr.com/1622/23992045861_338c0e1929_z.jpg) (https://flic.kr/p/Cy6vn8)
Orion v2 w/OTD Red Alert (https://flic.kr/p/Cy6vn8) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
Post by: appleonama on Thu, 31 December 2015, 12:38:15
Show Image
There needs to be pictures in here, since I haven't shared in awhile:
(https://farm6.staticflickr.com/5793/23995949621_4ce521e4fe_z.jpg) (https://flic.kr/p/CyrvPk)
Orion v2 with Zealios (https://flic.kr/p/CyrvPk) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
(https://farm2.staticflickr.com/1622/23992045861_338c0e1929_z.jpg) (https://flic.kr/p/Cy6vn8)
Orion v2 w/OTD Red Alert (https://flic.kr/p/Cy6vn8) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
sex
Post by: Pemdas on Thu, 31 December 2015, 16:19:08
Show Image
There needs to be pictures in here, since I haven't shared in awhile:
(https://farm6.staticflickr.com/5793/23995949621_4ce521e4fe_z.jpg) (https://flic.kr/p/CyrvPk)
Orion v2 with Zealios (https://flic.kr/p/CyrvPk) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
(https://farm2.staticflickr.com/1622/23992045861_338c0e1929_z.jpg) (https://flic.kr/p/Cy6vn8)
Orion v2 w/OTD Red Alert (https://flic.kr/p/Cy6vn8) by Steve N (https://www.flickr.com/photos/137225850@N04/), on Flickr
That red alert looks great on the black top :thumb: :thumb:
Post by: alienman82 on Thu, 31 December 2015, 16:23:46
Post by: appleonama on Fri, 01 January 2016, 16:40:10
Post by: alienman82 on Fri, 01 January 2016, 16:41:00
Anyone have a guide on the keyboard software. I am having trouble getting this thing to work. I was able to get it working on the duck eagle a couple months ago but now I can't get it to work.
I had a viper and got everything to work if you wanna pm me I'll try to help
Post by: Steezus on Fri, 01 January 2016, 16:48:44
Anyone have a guide on the keyboard software. I am having trouble getting this thing to work. I was able to get it working on the duck eagle a couple months ago but now I can't get it to work.
Other than Duck's page listing all the functionalities I don't think there is a guide. http://duck0113.tistory.com/124
I'm also more than willing to help out if you want to shoot me a PM, I got mine working rather quickly and like to think that I got the hang of the software by now.
Post by: appleonama on Fri, 01 January 2016, 17:09:41
Anyone have a guide on the keyboard software. I am having trouble getting this thing to work. I was able to get it working on the duck eagle a couple months ago but now I can't get it to work.
I had a viper and got everything to work if you wanna pm me I'll try to help
Anyone have a guide on the keyboard software. I am having trouble getting this thing to work. I was able to get it working on the duck eagle a couple months ago but now I can't get it to work.
Other than Duck's page listing all the functionalities I don't think there is a guide. http://duck0113.tistory.com/124
I'm also more than willing to help out if you want to shoot me a PM, I got mine working rather quickly and like to think that I got the hang of the software by now.
just found http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docx
ill try to see if I can get it going
Post by: Steezus on Fri, 01 January 2016, 17:21:49
just found http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docxAnyone have a guide on the keyboard software. I am having trouble getting this thing to work. I was able to get it working on the duck eagle a couple months ago but now I can't get it to work.
Other than Duck's page listing all the functionalities I don't think there is a guide. http://duck0113.tistory.com/124
I'm also more than willing to help out if you want to shoot me a PM, I got mine working rather quickly and like to think that I got the hang of the software by now.
ill try to see if I can get it going
Awesome, I actually didn't know that exists. One thing I forgot that may help, when I was having trouble getting the hex files to save. If you make a txt file first with the same name then it allows you save the hex file over it. I don't know if everybody was experiencing this problem but it occurred for me.
Post by: appleonama on Fri, 01 January 2016, 18:20:55
Think I could use a korean version of window in vmware to overcome the arrow keys issuejust found http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docxAnyone have a guide on the keyboard software. I am having trouble getting this thing to work. I was able to get it working on the duck eagle a couple months ago but now I can't get it to work.
Other than Duck's page listing all the functionalities I don't think there is a guide. http://duck0113.tistory.com/124
I'm also more than willing to help out if you want to shoot me a PM, I got mine working rather quickly and like to think that I got the hang of the software by now.
ill try to see if I can get it going
Awesome, I actually didn't know that exists. One thing I forgot that may help, when I was having trouble getting the hex files to save. If you make a txt file first with the same name then it allows you save the hex file over it. I don't know if everybody was experiencing this problem but it occurred for me.
Post by: rainb1ood on Fri, 01 January 2016, 18:30:22
Post by: appleonama on Fri, 01 January 2016, 19:19:52
In the octagon thread, there is a workaround with using microsoft app locale. Doesnt work with Windows 10 tho.
got it to work :thumb:
Post by: alienman82 on Fri, 01 January 2016, 20:36:06
Post by: appleonama on Fri, 01 January 2016, 20:41:03
Post by: HannahPeach on Sat, 02 January 2016, 07:13:03
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
Looks awesome, congratz. Now to go looking for feng's cyan. :D
Post by: orcinus on Sat, 02 January 2016, 11:21:46
Just to make sure - it was posted from an individual, right? Not a business?
Asking because individual == i can use the paypal/bank statement as proof of purchase; whereas for a business PoP == invoice.
Post by: alienman82 on Sat, 02 January 2016, 11:30:22
Mine finally surfaced at the customs today (9 days later).
Just to make sure - it was posted from an individual, right? Not a business?
Asking because individual == i can use the paypal/bank statement as proof of purchase; whereas for a business PoP == invoice.
from memory pretty such it was a person
Post by: alienman82 on Sat, 02 January 2016, 12:22:11
Mine finally surfaced at the customs today (9 days later).
Just to make sure - it was posted from an individual, right? Not a business?
Asking because individual == i can use the paypal/bank statement as proof of purchase; whereas for a business PoP == invoice.
from memory pretty such it was a person
No says mycnc co
(http://images.tapatalk-cdn.com/16/01/02/c030deff953966621a6a11cbea7879cf.jpg)
Post by: alienman82 on Sat, 02 January 2016, 15:50:24
Diodes all damn day
Post by: alienman82 on Sat, 02 January 2016, 19:59:07
Post by: orcinus on Sat, 02 January 2016, 20:01:18
No says mycnc coShow Image(http://images.tapatalk-cdn.com/16/01/02/c030deff953966621a6a11cbea7879cf.jpg)
Excellent, thank you.
If the package contains the invoice, that means less days of back and forth with the customs.
Post by: appleonama on Sat, 02 January 2016, 20:13:26
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Post by: alienman82 on Sat, 02 January 2016, 20:14:02
well after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Which plate do you have?
Post by: appleonama on Sat, 02 January 2016, 20:20:47
steelwell after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Which plate do you have?
Post by: Steezus on Sat, 02 January 2016, 20:34:17
well after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Nothing is worse than soldering up a whole board and then not liking the switches. I can definitely vouch for the 65g Tactile Zealios though, I have those in my Orion and love them, I do however have a plastic plate but that muffles the sound and gives a little more tactility. Best of luck and take your time, don't want to ruin a good PCB. :thumb:
Post by: appleonama on Sat, 02 January 2016, 20:45:33
well after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Nothing is worse than soldering up a whole board and then not liking the switches. I can definitely vouch for the 65g Tactile Zealios though, I have those in my Orion and love them, I do however have a plastic plate but that muffles the sound and gives a little more tactility. Best of luck and take your time, don't want to ruin a good PCB. :thumb:
yeah I am definitely being very careful with my pcb but dam this solder sucker makes my life much easier. The only trouble is the tiny led holes the solder becomes solid way too quick.
Post by: Steezus on Sat, 02 January 2016, 20:48:11
well after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Nothing is worse than soldering up a whole board and then not liking the switches. I can definitely vouch for the 65g Tactile Zealios though, I have those in my Orion and love them, I do however have a plastic plate but that muffles the sound and gives a little more tactility. Best of luck and take your time, don't want to ruin a good PCB. :thumb:
yeah I am definitely being very careful with my pcb but dam this solder sucker makes my life much easier.
Yeah mine has treated me quite well. I had to de-solder both Pok3rs since the LED holes came pre-filled, and then after finishing soldering up one board I saw that Vortex posted that you need to put the LEDs in the opposite polarity of what the PCB says...
Post by: appleonama on Sat, 02 January 2016, 20:49:44
well after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Nothing is worse than soldering up a whole board and then not liking the switches. I can definitely vouch for the 65g Tactile Zealios though, I have those in my Orion and love them, I do however have a plastic plate but that muffles the sound and gives a little more tactility. Best of luck and take your time, don't want to ruin a good PCB. :thumb:
yeah I am definitely being very careful with my pcb but dam this solder sucker makes my life much easier.
Yeah mine has treated me quite well. I had to de-solder both Pok3rs since the LED holes came pre-filled, and then after finishing soldering up one board I saw that Vortex posted that you need to put the LEDs in the opposite polarity of what the PCB says...
oh man that sucks... The only issue I am having is getting the solder out of the tiny led holes. The solder becomes solid way too quick.
Post by: Steezus on Sat, 02 January 2016, 20:51:09
well after a couple hours of using lubed gateron blacks I regret them. I think I just prefer tactile switches.
I think I over lubed my switches which made them feel buttery. Anyways I am going to desolder and replace them with 65g zealios
Nothing is worse than soldering up a whole board and then not liking the switches. I can definitely vouch for the 65g Tactile Zealios though, I have those in my Orion and love them, I do however have a plastic plate but that muffles the sound and gives a little more tactility. Best of luck and take your time, don't want to ruin a good PCB. :thumb:
yeah I am definitely being very careful with my pcb but dam this solder sucker makes my life much easier.
Yeah mine has treated me quite well. I had to de-solder both Pok3rs since the LED holes came pre-filled, and then after finishing soldering up one board I saw that Vortex posted that you need to put the LEDs in the opposite polarity of what the PCB says...
oh man that sucks... The only issue I am having is getting the solder out of the tiny led holes. The solder becomes solid way too quick.
Yeah the LED holes are the trickiest of them all, I always found it best to get a good bit of solder on them(add some more if need be) and then that helps get it all at once.
Post by: orcinus on Sat, 02 January 2016, 22:33:12
Saved my ass a ton of times.
Just be careful not to get the solder flow through to the other side of the board and pool up in a blob there.
If it does, try sucking from that side.
What i also sometimes do before adding more solder is slathering the top side with flux.
That will make any added solder prefer to spread (lower surface tension) on that side, in turn making it easier to heat up and keeping it hot long enough to suck.
Post by: alienman82 on Sun, 03 January 2016, 01:13:13
Post by: naasfu on Sun, 03 January 2016, 01:17:32
Show Image(http://images.tapatalk-cdn.com/16/01/02/46ee283cae2b85e6b2dc00b518635027.jpg)Show Image(http://images.tapatalk-cdn.com/16/01/02/8c244b80dda97d116f9f37094039a276.jpg)
pretty. :) so the bottom half is acrylic?
Post by: Pemdas on Sun, 03 January 2016, 01:19:15
Show Image(http://images.tapatalk-cdn.com/16/01/02/46ee283cae2b85e6b2dc00b518635027.jpg)Show Image(http://images.tapatalk-cdn.com/16/01/02/8c244b80dda97d116f9f37094039a276.jpg)
That looks awesome! As someone who hasn't used alps but is alps-curious I'm kicking myself for not getting the alps add on :mad:
Post by: alienman82 on Sun, 03 January 2016, 01:19:32
Show Image(http://images.tapatalk-cdn.com/16/01/02/46ee283cae2b85e6b2dc00b518635027.jpg)Show Image(http://images.tapatalk-cdn.com/16/01/02/8c244b80dda97d116f9f37094039a276.jpg)
pretty. :) so the bottom half is acrylic?
Thanks! Yes bottom is acrylic. The blue alps in this baby have me quite the trouble had to repair a good 15 of them. Much headache. Actually ripped a trace by accident. And soldered 84 smd diodes. Worked a lot today but I am happy it all turned out ok. Definitely never doing alps again. **** em. Cherry all the way
Post by: alienman82 on Sun, 03 January 2016, 01:20:24
Show Image(http://images.tapatalk-cdn.com/16/01/02/46ee283cae2b85e6b2dc00b518635027.jpg)Show Image(http://images.tapatalk-cdn.com/16/01/02/8c244b80dda97d116f9f37094039a276.jpg)
That looks awesome! As someone who hasn't used alps but is alps-curious I'm kicking myself for not getting the alps add on :mad:
Maybe not haha. I'd say it's worth it but maybe not . As long as your switches are in good shape it would be easy
Post by: itzmeluigi on Sun, 03 January 2016, 05:10:44
Show Image(http://images.tapatalk-cdn.com/16/01/02/46ee283cae2b85e6b2dc00b518635027.jpg)Show Image(http://images.tapatalk-cdn.com/16/01/02/8c244b80dda97d116f9f37094039a276.jpg)
pretty. :) so the bottom half is acrylic?
Thanks! Yes bottom is acrylic. The blue alps in this baby have me quite the trouble had to repair a good 15 of them. Much headache. Actually ripped a trace by accident. And soldered 84 smd diodes. Worked a lot today but I am happy it all turned out ok. Definitely never doing alps again. **** em. Cherry all the way
That board is pure excellence great work, i wish i was paying attention when this GB was open and joined. What was wrong with the blue alps that required them to be repaired?
Post by: Jumie on Sun, 03 January 2016, 11:30:33
Post by: Steezus on Sun, 03 January 2016, 11:33:37
will there be the V3 next?
In probably close to two years from now, Duck's plan is to come out with the Octagon v2, then Lightsaver v3, and finally Orion v3. If each GB lasted as long as this one than that's about 9 months for each one.
Post by: alienman82 on Sun, 03 January 2016, 11:44:33
Show Image(http://images.tapatalk-cdn.com/16/01/02/46ee283cae2b85e6b2dc00b518635027.jpg)Show Image(http://images.tapatalk-cdn.com/16/01/02/8c244b80dda97d116f9f37094039a276.jpg)
pretty. :) so the bottom half is acrylic?
Thanks! Yes bottom is acrylic. The blue alps in this baby have me quite the trouble had to repair a good 15 of them. Much headache. Actually ripped a trace by accident. And soldered 84 smd diodes. Worked a lot today but I am happy it all turned out ok. Definitely never doing alps again. **** em. Cherry all the way
That board is pure excellence great work, i wish i was paying attention when this GB was open and joined. What was wrong with the blue alps that required them to be repaired?
Switches didn't register so I had to rebuild them and test with multimeter
Post by: orcinus on Mon, 04 January 2016, 15:18:18
(https://dl.dropboxusercontent.com/u/1702513/12510725_10153285802911404_522442889_o.jpg)
Post by: orcinus on Mon, 04 January 2016, 15:18:47
Post by: orcinus on Tue, 05 January 2016, 00:07:24
Wouldn't mind having another color option stashed.
Yeah, yeah, i know, should've thought of that when i was ordering...
Hindsight 20/20.
Post by: Steezus on Tue, 05 January 2016, 00:08:23
If anyone has a black or blue top case extra, that they'd be willing to part with, let me know.
Wouldn't mind having another color option stashed.
Yeah, yeah, i know, should've thought of that when i was ordering...
Hindsight 20/20.
I'm pretty sure the only way to get the top case is by having the buy the kit itself, the bottoms is what were the options.
Post by: orcinus on Tue, 05 January 2016, 04:25:00
I'm pretty sure the only way to get the top case is by having the buy the kit itself, the bottoms is what were the options.
That is correct.
I meant - in case someone bought multiple sets with the same idea (having more options to mix and match w/ a PCB spare; as opposed to assembling multiple keyboards), and then decided they don't want/need one.
However, i've just realized that all the multiple orders were for winkeyless and i've got a winkey set. So never mind after all :)
Post by: orcinus on Tue, 05 January 2016, 13:08:41
Haven't noticed it mentioned by anyone. It's pretty nasty, i'd say 60 Hz or so?
Post by: filphil on Tue, 05 January 2016, 13:10:22
Am i the only person annoyed by the PWM flicker of the backlight LEDs (keyswitch LEDs, not the back-*side* LEDs)?
Haven't noticed it mentioned by anyone. It's pretty nasty, i'd say 60 Hz or so?
My leds are being held hostage by Seth so I haven't been able to comment on that.
Post by: appleonama on Tue, 05 January 2016, 13:10:36
Am i the only person annoyed by the PWM flicker of the backlight LEDs (keyswitch LEDs, not the back-*side* LEDs)?I notice it as well but it is common with duck pcbs
Haven't noticed it mentioned by anyone. It's pretty nasty, i'd say 60 Hz or so?
Post by: Steezus on Tue, 05 January 2016, 13:15:30
Am i the only person annoyed by the PWM flicker of the backlight LEDs (keyswitch LEDs, not the back-*side* LEDs)?
Haven't noticed it mentioned by anyone. It's pretty nasty, i'd say 60 Hz or so?
I think it depends on the LEDs and the brightness settings, the lower the brightness the more noticeable imo. I haven't really noticed it all with the Pink LEDs that I'm using but in the low brightness settings with the White LEDs on my RS96 it is very noticeable.
Post by: orcinus on Tue, 05 January 2016, 14:12:32
I notice it at nearly full brightness.
Oh well... Perhaps it'll be less noticeable with the keycaps on.
Haven't assembled it yet, i'm stuck on trying to figure out why my space is sticky with a space bar on.
My current suspect is the cherry stab wire - it's likely bent a little too wide, so one of the stabs is at an angle instead of completely straight.
Post by: Steezus on Tue, 05 January 2016, 14:33:23
Yeah, white LEDs here.
I notice it at nearly full brightness.
Oh well... Perhaps it'll be less noticeable with the keycaps on.
Haven't assembled it yet, i'm stuck on trying to figure out why my space is sticky with a space bar on.
My current suspect is the cherry stab wire - it's likely bent a little too wide, so one of the stabs is at an angle instead of completely straight.
I have that issue on my RS96 but it's all soldered and the issue didn't start in the beginning, it seems to be ok for the time being but I'm definitely going to open it up and see what mischief is going on whenever I'm bored.
Post by: filphil on Tue, 05 January 2016, 14:37:08
Yeah, white LEDs here.
I notice it at nearly full brightness.
Oh well... Perhaps it'll be less noticeable with the keycaps on.
Haven't assembled it yet, i'm stuck on trying to figure out why my space is sticky with a space bar on.
My current suspect is the cherry stab wire - it's likely bent a little too wide, so one of the stabs is at an angle instead of completely straight.
Also when building it make sure to align your pcb so that it's straight with the top case when everything is tightened. I noticed that my space was slow to return and just had to do what i described. I think it's more prevalent on wkl boards because my brothers winkey board didn't have that issue.
Post by: orcinus on Tue, 05 January 2016, 15:39:15
I think i'll mount some keycaps on, then align, test the edge keys, adjust and only then tighten to the top case.
Post by: orcinus on Tue, 05 January 2016, 15:58:10
It seems the space stab holes are mounted ever so slightly too close to each other, or, the wire i've got was ever so slightly too long (as i've correctly guessed initially). This then causes the stab stems to rub against the edge of the stabilizer housing (the wire displaces the bottom too far to the left on the left stab and too far to the right on the right stab - since the stems can pivot around the wire, this forces the stems to rub against the right and left wall of the housing respectively).
While i was troubleshooting, i first tried lightly shaving off some material off the moving part of the stabilizer under the stem with an emery file. Bad idea. It leaves a sandpapery feel to the stabilizer that i had to smooth with sandpaper, and it all amounted to nothing.
What did help was removing the stab wire (you don't need to remove the plate or desolder anything to do that, it's accessible through the hole and on the side - if you need to do this and can't figure it out, let me know, i'll help), take the pliers and lightly bend the short segments *inwards*, like this:
/_______\
And by *lightly*, i mean really lightly. It's a trial and error thing. You bend it a little, put it back, mount a space bar cap, try it, remove it, remove the wire, bend a little more etc. until it's just right.
I'm getting 0 stickyness now and the sandpaper texture is irrelevant, as the stem isn't chafing the edge of the housing anymore anyways.
Post by: R1N3 on Tue, 05 January 2016, 16:01:43
Little update in case someone encounters the same issue...Meant to ask about this last night, I'm glad you said something before I forgot.
It seems the space stab holes are mounted ever so slightly too close to each other, or, the wire i've got was ever so slightly too long (as i've correctly guessed initially). This then causes the stab stems to rub against the edge of the stabilizer housing (the wire displaces the bottom too far to the left on the left stab and too far to the right on the right stab - since the stems can pivot around the wire, this forces the stems to rub against the right and left wall of the housing respectively).
While i was troubleshooting, i first tried lightly shaving off some material off the moving part of the stabilizer under the stem with an emery file. Bad idea. It leaves a sandpapery feel to the stabilizer that i had to smooth with sandpaper, and it all amounted to nothing.
What did help was removing the stab wire (you don't need to remove the plate or desolder anything to do that, it's accessible through the hole and on the side - if you need to do this and can't figure it out, let me know, i'll help), take the pliers and lightly bend the short segments *inwards*, like this:
/_______\
And by *lightly*, i mean really lightly. It's a trial and error thing. You bend it a little, put it back, mount a space bar cap, try it, remove it, remove the wire, bend a little more etc. until it's just right.
I'm getting 0 stickyness now and the sandpaper texture is irrelevant, as the stem isn't chafing the edge of the housing anymore anyways.
Post by: orcinus on Tue, 05 January 2016, 20:51:33
Post by: orcinus on Tue, 05 January 2016, 21:35:25
Post by: Steezus on Tue, 05 January 2016, 21:37:31
What's the FLIP key on this keyboard?
Backspace
Post by: orcinus on Tue, 05 January 2016, 22:02:48
Backspace
Of course, the only one i didn't try.
Thanks!
I can't figure out the LED controls for the life of me. LED Down seems to turn the LEDs off. LED Up seems to turn them on. No idea how to change the brightness. Oh well, something to play with tomorrow, it's 5am already.
Post by: Steezus on Tue, 05 January 2016, 22:05:12
Backspace
Of course, the only one i didn't try.
Thanks!
I can't figure out the LED controls for the life of me. LED Down seems to turn the LEDs off. LED Up seems to turn them on. No idea how to change the brightness. Oh well, something to play with tomorrow, it's 5am already.
Pretty sure you need to press LED Control first and then the brightness settings will work.
Post by: appleonama on Tue, 05 January 2016, 22:23:26
Post by: ika on Tue, 05 January 2016, 23:31:22
So I'm just planning ahead. How many of you add a heavier spring to your space bar? I have 78g gold springs I plan to put on the my space bar due to having a sticky space bar on my GON. good idea or bad?
I'm putting a Cherry Tactile Gray on my spacebar, with 62g lubed Ergo Clears on everything else. I like a bit of weight behind the spacebar, although I will also put an o-ring on it to quiet it down a little bit. I made the mistake of putting a Cherry White on my current B.87 with Zealios and it makes a huge clatter.
Post by: Steezus on Tue, 05 January 2016, 23:33:56
So I'm just planning ahead. How many of you add a heavier spring to your space bar? I have 78g gold springs I plan to put on the my space bar due to having a sticky space bar on my GON. good idea or bad?
I'm putting a Cherry Tactile Gray on my spacebar
+1
I got that in my spacebar for my Jane and love it. However I went full Zealios in my Orion because having all Purple stems and one Gray one would look weird af in my opinion.
Post by: romevi on Tue, 05 January 2016, 23:38:39
So I'm just planning ahead. How many of you add a heavier spring to your space bar? I have 78g gold springs I plan to put on the my space bar due to having a sticky space bar on my GON. good idea or bad?
I'm putting a Cherry Tactile Gray on my spacebar
+1
I got that in my spacebar for my Jane and love it. However I went full Zealios in my Orion because having all Purple stems and one Gray one would look weird af in my opinion.
My Zealio & Tactile Gray Jane is superior. Fite mii.
Post by: appleonama on Tue, 05 January 2016, 23:41:50
Post by: Steezus on Tue, 05 January 2016, 23:56:00
So I'm just planning ahead. How many of you add a heavier spring to your space bar? I have 78g gold springs I plan to put on the my space bar due to having a sticky space bar on my GON. good idea or bad?
I'm putting a Cherry Tactile Gray on my spacebar
+1
I got that in my spacebar for my Jane and love it. However I went full Zealios in my Orion because having all Purple stems and one Gray one would look weird af in my opinion.
My Zealio & Tactile Gray Jane is superior. Fite mii.
It's a quality board so I'll let it slide. :p
So would 78g on zealios be good or bad? should I buy a grey switch?
I'd try the 78g in the Zealios. Tactile Grey feels very similar to a clear imo.
Post by: Want on Wed, 06 January 2016, 04:44:01
E:
Post by: Arvid on Wed, 06 January 2016, 09:19:31
Looks like I have to let mine go. Will be putting up a classifieds thread, but thought I'd post here first. I've only opened the package to check for damages, there were none.
Pmd!
Post by: filphil on Wed, 06 January 2016, 09:25:48
Looks like I have to let mine go. Will be putting up a classifieds thread, but thought I'd post here first. I've only opened the package to check for damages, there were none.
Pmd!
from sweden to sweden. Awfully lucky!
Post by: romevi on Wed, 06 January 2016, 09:32:55
Looks like I have to let mine go. Will be putting up a classifieds thread, but thought I'd post here first. I've only opened the package to check for damages, there were none.
PM'd!
Post by: orcinus on Wed, 06 January 2016, 10:25:44
It's way too mushy and sticky.
I'm on 62g clears.
It's so bad i'm actually considering putting a blue on the space bar as a temporary measure.
Other large keys are iffy too, but tolerable for modifiers.
Return is a bit too mushy for my tastes as well, if i go the replacement spring route, i'll probably swap that too.
Post by: orcinus on Wed, 06 January 2016, 17:08:22
Pretty sure you need to press LED Control first and then the brightness settings will work.
How do you "commit" the change?
Also, for some reason, now the changes made to the underglow LED pattern in 02D KeyMapper won't apply to the board.
I thought it was just me being very tired last night, but apparently, i'm way too daft to figure this thing out :'(
Post by: slushi on Wed, 06 January 2016, 18:09:57
Post by: orcinus on Wed, 06 January 2016, 19:24:40
Pretty sure you need to press LED Control first and then the brightness settings will work.
How do you "commit" the change?
Okay, so hitting LED Control again commits.
But if you hit LED Control AGAIN, it shuts down all the LED sections. And you basically need to turn them on again then set the brightness. Very bizarre behaviour. I've also managed to get the underglow LEDs to flicker really really badly somehow, no idea how. I don't mean breathe slowly, nor pulsate, but really flicker at like 20Hz or so. Hitting LED Control and RGB Mode a few times fixed it. Couldn't replicate, i think it's a weird bug.
Annnyways, i think i've finally cured my space bar:
Post by: appleonama on Wed, 06 January 2016, 19:26:49
Pretty sure you need to press LED Control first and then the brightness settings will work.
How do you "commit" the change?
Okay, so hitting LED Control again commits.
But if you hit LED Control AGAIN, it shuts down all the LED sections. And you basically need to turn them on again then set the brightness. Very bizarre behaviour. I've also managed to get the underglow LEDs to flicker really really badly somehow, no idea how. I don't mean breathe slowly, nor pulsate, but really flicker at like 20Hz or so. Hitting LED Control and RGB Mode a few times fixed it. Couldn't replicate, i think it's a weird bug.
Annnyways, i think i've finally cured my space bar:
SA on orion :'(
Post by: orcinus on Wed, 06 January 2016, 19:51:23
Post by: R1N3 on Wed, 06 January 2016, 19:52:45
Post by: orcinus on Wed, 06 January 2016, 19:58:01
1) bend the wire as i've described (/____\)
2) lube the stabs - both where the wire is anchored and the stab stems
3) insert and remove the wire like a dozen times before the anchors loosened a bit
Now it's fine. Activation force is still a bit too low for such a big key, but at least there's 0 sticking now.
Post by: R1N3 on Wed, 06 January 2016, 20:00:47
What'd you use as lubricant? I've got graphite on hand but no liquids
Post by: orcinus on Wed, 06 January 2016, 20:04:48
Actually was a 50/50 oil/grease mix, but the oil ran away from the bottle. No idea where.
Now it's grease.
Post by: slushi on Wed, 06 January 2016, 22:09:33
Post by: orcinus on Thu, 07 January 2016, 09:07:09
But the firmware is pretty buggy.
Some combinations of backlight and underglow brightnesses causes either of those to flicker badly (i assume due to some kind of temporal aliasing effect in the interrupt loop that controls the LEDs). Also, sometimes, in use, some sections of backlight temporarily fade down in brightness, then come back to the actual preset brightness (and no, that's not an effect, this is with constant on).
Now i'm trying to figure out the debounce settings, as i sometimes get double spaces.
Post by: orcinus on Thu, 07 January 2016, 16:50:15
Yes, it's Granite. Yes, it's DSA. I don't like cylindrical profile. Get over it :P
(https://dl.dropboxusercontent.com/u/1702513/DSCF4818_resize.jpg)
(https://dl.dropboxusercontent.com/u/1702513/DSCF4831_resize.jpg)
(https://dl.dropboxusercontent.com/u/1702513/DSCF4824_resize.jpg)
(https://dl.dropboxusercontent.com/u/1702513/DSCF4821_resize.jpg)
Post by: HannahPeach on Thu, 07 January 2016, 18:15:31
A few gratuitous shots.
Yes, it's Granite. Yes, it's DSA. I don't like cylindrical profile. Get over it :PShow Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4818_resize.jpg)Show Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4831_resize.jpg)Show Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4824_resize.jpg)Show Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4821_resize.jpg)
It turned out just marvellous, congratz!
Post by: ika on Thu, 07 January 2016, 23:19:31
also what exactly do the five LEDs indicate? I need to catch up on how this keyboard works.
Post by: Steezus on Thu, 07 January 2016, 23:43:42
Just opened my package it's... it's beautiful. I had some time today to put together the rest of my MX clears so hopefully I'll have it done by this weekend! One thing I didn't find, how were the indicator LEDs supposed to work? I don't have anything soldered in the holes and I don't see any bags containing LEDs. Were we supposed to provide our own LEDs?
also what exactly do the five LEDs indicate? I need to catch up on how this keyboard works.
You're suppose to provide your own LEDs for the indicators. The five indicators above your arrow keys are for your layers with the fifth being the temp layer. The three indicators next to your ESC key are for your Scroll, Num, and Caps Lock.
Post by: ika on Fri, 08 January 2016, 00:37:30
Just opened my package it's... it's beautiful. I had some time today to put together the rest of my MX clears so hopefully I'll have it done by this weekend! One thing I didn't find, how were the indicator LEDs supposed to work? I don't have anything soldered in the holes and I don't see any bags containing LEDs. Were we supposed to provide our own LEDs?
also what exactly do the five LEDs indicate? I need to catch up on how this keyboard works.
You're suppose to provide your own LEDs for the indicators. The five indicators above your arrow keys are for your layers with the fifth being the temp layer. The three indicators next to your ESC key are for your Scroll, Num, and Caps Lock.
Oh, ok. Didn't expect that but it's not a problem. What LED colors are people using for these? There shouldn't be an issue mixing and matching high vs lower current LEDs, right? (e.g. white LEDs on switches and red/blue/green/orange LEDs on indicators).
Post by: ctrlX on Fri, 08 January 2016, 05:04:12
A few gratuitous shots.Looks awsome! I was also thinking of using my Granite set but with black top and bottom aluminium housing. Unfortunately my EU soldering service guy is not responding to PM. Seems I have to wait even longer before I can start using this beauty :(
Yes, it's Granite. Yes, it's DSA. I don't like cylindrical profile. Get over itShow Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4818_resize.jpg)Show Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4831_resize.jpg)Show Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4824_resize.jpg)Show Image(https://dl.dropboxusercontent.com/u/1702513/DSCF4821_resize.jpg)
Can anyone recommend other EU based soldering service in case he never replies?
Post by: orcinus on Fri, 08 January 2016, 13:49:29
Just opened my package it's... it's beautiful. I had some time today to put together the rest of my MX clears so hopefully I'll have it done by this weekend! One thing I didn't find, how were the indicator LEDs supposed to work? I don't have anything soldered in the holes and I don't see any bags containing LEDs. Were we supposed to provide our own LEDs?
also what exactly do the five LEDs indicate? I need to catch up on how this keyboard works.
You're suppose to provide your own LEDs for the indicators. The five indicators above your arrow keys are for your layers with the fifth being the temp layer. The three indicators next to your ESC key are for your Scroll, Num, and Caps Lock.
Oh, ok. Didn't expect that but it's not a problem. What LED colors are people using for these? There shouldn't be an issue mixing and matching high vs lower current LEDs, right? (e.g. white LEDs on switches and red/blue/green/orange LEDs on indicators).
There's no issue. They're driven separately.
I'm using yellow for first layer, white for upper three layers, red for the last LED.
BTW, the last LED isn't quite for temporary layer.
It generally indicates any "non-standard" mode + settings changes.
For mode changes, it tends to blink once when entering and multiple times when exiting.
Temporary layer does that, as well as LED control mode and various LED ops.
Macro recording too. Control mode (the mode in which you can access the KB settings) lights it constantly until you exit Control mode.
Edit: Oh, also, the first 4 LEDs also indicate FN layers, but in an "inverse" fashion from regular layers. E.g. FN1 = off on on on; FN2 = on off on on, FN3 = on on off on.
Post by: orcinus on Fri, 08 January 2016, 13:51:25
It turned out just marvellous, congratz!
Looks awsome! I was also thinking of using my Granite set but with black top and bottom aluminium housing. Unfortunately my EU soldering service guy is not responding to PM. Seems I have to wait even longer before I can start using this beauty :(
Thanks, guys.
I think granite DSA matches silver pretty nicely. Also, i think Dolch might be interesting on blue-gray or black.
Post by: orcinus on Fri, 08 January 2016, 13:55:03
(http://i.imgur.com/svgquRC.jpg)
Post by: xondat on Fri, 08 January 2016, 14:20:14
All classy and crap:Show Image(http://i.imgur.com/svgquRC.jpg)
Oh boy :eek:
Post by: MrChunky on Fri, 08 January 2016, 14:48:35
(http://imgur.com/hi98toA.jpg)
Post by: Rainbow_ on Fri, 08 January 2016, 14:56:27
(https://i.imgur.com/34IG86A.jpg)
Post by: MrChunky on Fri, 08 January 2016, 15:04:44
my photography is garbageShow Image(https://i.imgur.com/34IG86A.jpg)
Your board is great though ;)
Also your photography is fine. One day I'll also get my Hyperfuse... :p
Post by: ramnes on Fri, 08 January 2016, 15:13:22
Anyone knows if there's a way to control the five LEDs on the right software side?
Post by: Steezus on Fri, 08 January 2016, 15:22:17
Looks awesome, best Orion so far to me!
Anyone knows if there's a way to control the five LEDs on the right software side?
They're indicators, nothing really that you can control about them.
Post by: orcinus on Fri, 08 January 2016, 16:38:38
Looks awesome, best Orion so far to me!
Anyone knows if there's a way to control the five LEDs on the right software side?
They're indicators, nothing really that you can control about them.
Eyup, nothing you can do, unless you decide to port TMK to Orion v2 :)
Post by: orcinus on Fri, 08 January 2016, 16:39:32
my photography is garbageShow Image(https://i.imgur.com/34IG86A.jpg)
Photo's perfectly fine.
It's weird how i couldn't stand Hyperfuse (i dunno why, i just found it obnoxious), but i'm now finding it looks nice on an Orion.
Post by: orcinus on Sat, 09 January 2016, 15:22:04
Anyone got any experience with adjusting the debounce settings in Control Mode?
Post by: elton5354 on Sun, 10 January 2016, 21:36:02
Post by: Dreamre on Sun, 10 January 2016, 22:02:30
Octagon V2 GB will be up soon.
:eek:
I can't wait! ;D :D ;) :-*
Post by: Sifo on Sun, 10 January 2016, 22:03:30
Octagon V2 GB will be up soon.
:eek:
I can't wait! ;D :D ;) :-*
u'll have to wait a year for the gb to actually finish so I'd work on the whole "can't wait" thing.
Post by: Dreamre on Sun, 10 January 2016, 22:11:20
Octagon V2 GB will be up soon.
:eek:
I can't wait! ;D :D ;) :-*
u'll have to wait a year for the gb to actually finish so I'd work on the whole "can't wait" thing.
What a hater! I hope our sushi meetup won't take 6 months to plan and meet LOL.
Post by: havenlau on Sun, 10 January 2016, 23:25:52
DONE! Man this took me forever to finish. I was doing everything in fine detail. I am having an issue with my print screen button going off hundreds of times in seconds any ideas?where did u get your cyan from?
The LED's were going to be temporary because I didn't have enough of cyan but I really love how the colors mix. Also the TA set looked ugly at first but now it is love at first sight on the orionShow Image(http://i.imgur.com/Jc2KQdc.jpg)
last time I got a bunch of 2x3x4 cyan from aliexpress they look more green than cyan :(
http://www.aliexpress.com/item/High-Quality-100pcs-2x3x4-Rectangular-square-type-Cyan-led-lighting-beads-brightness600-MCD-for-backlight/1342964772.html (http://www.aliexpress.com/item/High-Quality-100pcs-2x3x4-Rectangular-square-type-Cyan-led-lighting-beads-brightness600-MCD-for-backlight/1342964772.html)
Post by: stillzman on Mon, 11 January 2016, 00:14:03
Post by: MrRooks on Mon, 11 January 2016, 00:20:26
will there be a new thread for the new GB?
Definitely
Post by: lanyusea on Mon, 11 January 2016, 02:39:59
Octagon V2 GB will be up soon.
may I ask for the schedule of Viper ... ?
Post by: gadzkun on Mon, 11 January 2016, 02:51:00
Octagon V2 GB will be up soon.
may I ask for the schedule of Viper ... ?
maybe 2017... duck project on 2016 is
octagon V2 > Lightsaver V3 > Orion V3
Post by: ika on Mon, 11 January 2016, 03:13:46
The keyboard seems to work just fine otherwise, but I don't have a way to access layers or functions and the LEDs are annoyingly bright. One quirk I've noticed is that RGui press activates both RGUI and Menu, not sure if this is a keymap issue or a soldering issue. I don't see any bridges, but since I can't change the keymap I can't confirm if it's a problem.
Post by: lanyusea on Mon, 11 January 2016, 03:22:02
Octagon V2 GB will be up soon.
may I ask for the schedule of Viper ... ?
maybe 2017... duck project on 2016 is
octagon V2 > Lightsaver V3 > Orion V3
Glad to hear it is not 2018! :3
Post by: kacase on Mon, 11 January 2016, 03:41:13
I'm having issues uploading a new keymap. I installed Atmel Flip and the Java runtime but whenever I try to access USB devices it gives me an error saying "atilibusbdfu.dll not found". I figure Windows doesn't have the proper drivers installed for the keyboard but I don't see any Atmel devices in the Device Manager like in his tutorial page, and I can't seem to be able to manually install the correct USB driver. Anyone have a how-to?
The keyboard seems to work just fine otherwise, but I don't have a way to access layers or functions and the LEDs are annoyingly bright. One quirk I've noticed is that RGui press activates both RGUI and Menu, not sure if this is a keymap issue or a soldering issue. I don't see any bridges, but since I can't change the keymap I can't confirm if it's a problem.
This is the guide I posted some time ago...
I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
I don't believe so, it's just standard procedure for assembling every board. It's also a big help that the all the SMD parts come pre-soldered. If you're having trouble building I suggest you take look some member's build logs, that's how I learned to build my first board. :thumb:
Edit: Oops I think you may mean the case itself and not the board, if so there so there are no instructions listed for that.
lol yeah, I meant the case. I've done SMD soldering before and it's not that bad. I guess I'll look harder at it when I get my switches and stabs.
Instructions
Assembly
Except for the Switches and in Switch Leds/SIPs there is no soldering you have to do. The Assembly couldnt be more straight forwards:
1. Install stabs on pcb
2. Solder Switches and LEDs
3. Screw Plate PCB combo onto the top cover with 8 round head screws (put top cover upside down)
4. Put the two acrylic inserts into place (after removing the protective film)
5. Put Top cover into place on top of the bottom one with acrylic inserts inbetween
6. Flip upside down and screw together (4 small flat screws 4 very long cylindrical screws for the angled bottoms, 8 flat screws for the flat acrylic bottom)
7. Turn upside down and you are finished ;)
Firmware
For the firmware its a bit more work..
I got most of the information from this guide:
https://drive.google.com/file/d/0B4Q2mepcAlZnWmx5V1d2QmZqZGs/view
1. Download the follwing files
http://sourceforge.net/projects/dfu-programmer/files/dfu-programmer/0.7.0/
https://gallery.atmel.com/Products/Details/6272a8fd-68fe-43d8-a990-741878cfe7b6 (sadly you will have to register for it >:D)
http://duck0113.tistory.com/124
2. Install the amtel usb driver
3. put the o2d mapper into the folder of the dfu programmer
4. Start up the o2dmapper and map your stuff
5. save your hex and rename it (long names make it crash)
6. disconnect your Orion V2
7. hold backspace and reconnect your v2
8. in the firmware upload popup click connect and upload your firmware
9. you are good to go! have fun with this amazing keyboard
These are not proper official instructions, but rather a sum up of how I assembled my Orion and updated the firmware. Please be careful when handeling your device and don't make me responsible for any damage that occurs.
Post by: ika on Mon, 11 January 2016, 03:45:49
I'm having issues uploading a new keymap. I installed Atmel Flip and the Java runtime but whenever I try to access USB devices it gives me an error saying "atilibusbdfu.dll not found". I figure Windows doesn't have the proper drivers installed for the keyboard but I don't see any Atmel devices in the Device Manager like in his tutorial page, and I can't seem to be able to manually install the correct USB driver. Anyone have a how-to?
The keyboard seems to work just fine otherwise, but I don't have a way to access layers or functions and the LEDs are annoyingly bright. One quirk I've noticed is that RGui press activates both RGUI and Menu, not sure if this is a keymap issue or a soldering issue. I don't see any bridges, but since I can't change the keymap I can't confirm if it's a problem.
This is the guide I posted some time ago...I'm sure this has been answered or it's very obvious, but is there a guide on assembling this?
I don't believe so, it's just standard procedure for assembling every board. It's also a big help that the all the SMD parts come pre-soldered. If you're having trouble building I suggest you take look some member's build logs, that's how I learned to build my first board. :thumb:
Edit: Oops I think you may mean the case itself and not the board, if so there so there are no instructions listed for that.
lol yeah, I meant the case. I've done SMD soldering before and it's not that bad. I guess I'll look harder at it when I get my switches and stabs.
Instructions
Assembly
Except for the Switches and in Switch Leds/SIPs there is no soldering you have to do. The Assembly couldnt be more straight forwards:
1. Install stabs on pcb
2. Solder Switches and LEDs
3. Screw Plate PCB combo onto the top cover with 8 round head screws (put top cover upside down)
4. Put the two acrylic inserts into place (after removing the protective film)
5. Put Top cover into place on top of the bottom one with acrylic inserts inbetween
6. Flip upside down and screw together (4 small flat screws 4 very long cylindrical screws for the angled bottoms, 8 flat screws for the flat acrylic bottom)
7. Turn upside down and you are finished ;)
Firmware
For the firmware its a bit more work..
I got most of the information from this guide:
https://drive.google.com/file/d/0B4Q2mepcAlZnWmx5V1d2QmZqZGs/view
1. Download the follwing files
http://sourceforge.net/projects/dfu-programmer/files/dfu-programmer/0.7.0/
https://gallery.atmel.com/Products/Details/6272a8fd-68fe-43d8-a990-741878cfe7b6 (sadly you will have to register for it >:D)
http://duck0113.tistory.com/124
2. Install the amtel usb driver
3. put the o2d mapper into the folder of the dfu programmer
4. Start up the o2dmapper and map your stuff
5. save your hex and rename it (long names make it crash)
6. disconnect your Orion V2
7. hold backspace and reconnect your v2
8. in the firmware upload popup click connect and upload your firmware
9. you are good to go! have fun with this amazing keyboard
These are not proper official instructions, but rather a sum up of how I assembled my Orion and updated the firmware. Please be careful when handeling your device and don't make me responsible for any damage that occurs.
Thanks! Exactly what I needed. Didn't even realize my instructions were for duck/viper and not orion-specific. Got everything loaded up now, just need to put indicators, dress it with keycaps, and break out the glamour camera!
Post by: Steezus on Mon, 11 January 2016, 09:57:00
Octagon V2 GB will be up soon.
may I ask for the schedule of Viper ... ?
maybe 2017... duck project on 2016 is
octagon V2 > Lightsaver V3 > Orion V3
Glad to hear it is not 2018! :3
It most likely will be 2019. Think of it this way, if each group buy lasts as long as the Orion v2(9 months) then that'll be 27 months or 2 years and 3 months away until the Orion v3 group buy will be complete. Then you'll most likely have to wait another 9 months for the Viper/Eagle group buy to finish, so that's overall 36 months or 3 years when you'll get one at your doorstep. Who knows Duck may be able to step it up by a couple months but it'll still be a long time.
Post by: orcinus on Mon, 11 January 2016, 18:41:02
It doesn't happen VERY often, but it happens.
I'm guessing default debounce is extremely conservative, possibly to get the poll rate as high as possible.
Post by: lanyusea on Mon, 11 January 2016, 21:28:22
Octagon V2 GB will be up soon.
may I ask for the schedule of Viper ... ?
maybe 2017... duck project on 2016 is
octagon V2 > Lightsaver V3 > Orion V3
Glad to hear it is not 2018! :3
It most likely will be 2019. Think of it this way, if each group buy lasts as long as the Orion v2(9 months) then that'll be 27 months or 2 years and 3 months away until the Orion v3 group buy will be complete. Then you'll most likely have to wait another 9 months for the Viper/Eagle group buy to finish, so that's overall 36 months or 3 years when you'll get one at your doorstep. Who knows Duck may be able to step it up by a couple months but it'll still be a long time.
you must be a genius in mathematics :thumb:
Post by: whentheclouds on Tue, 12 January 2016, 05:19:21
think positive guys :]
Post by: E3E on Tue, 12 January 2016, 05:31:58
the first octagon took two and a half months between orders closing and buyers receiving their board, for ~35 units. this is with a 2 week delay due to the metal stickers iirc. so the best case scenario for a 60 unit buy would be to last <4 months between orders closing and shipments being made. obviously the orion2 buy had a number of setbacks that extended its duration, but there's no reason to assume that duck will run into anything of the sorts again
think positive guys :]
I think it was around 38 orders, or rather 38 boards total. I could be wrong. In any case, I think the v1 is going to be a lot more scarce than the upcoming v2 that's in the GB phase. There's already 42 orders and the deadline isn't until February!
I'm definitely down to get the new Octagon for SNES GMK whenever it gets relaunched.
I do kind of dig that the first Octagon is going to be more rare. Not necessarily more desirable, but hey... How can you not find the charm in the little 'name plate' portion that makes the board an actual octagon... an irregular octagon at least, lol. :D
I don't think the wait will be long, but whatever the case may ultimately be, I don't mind either way.
Post by: ika on Tue, 12 January 2016, 18:41:44
My bounce issue is spreading. Now it's not just space anymore, it's other (random) keys.
It doesn't happen VERY often, but it happens.
I'm guessing default debounce is extremely conservative, possibly to get the poll rate as high as possible.
What switches are you using? Related, how did you fix the spacebar stickiness? I've got some friction with my spacebar stab and didn't notice until after I had already soldered on all my switches. Hoping it just goes away over time.
Post by: seedvd on Tue, 12 January 2016, 19:49:04
Post by: 64rky on Tue, 12 January 2016, 20:47:41
I am letting my order go, pm me if you are interested.
Pm'd
Post by: ika on Wed, 13 January 2016, 00:06:49
Post by: Pemdas on Wed, 13 January 2016, 06:11:31
Post by: 64rky on Wed, 13 January 2016, 07:36:05
Thanks.
Post by: pichu23 on Wed, 13 January 2016, 07:38:06
This is such a n00b question n, but: could someone tell me if the Winkeyless space bar is 7x or 6.25x? On my cherry board it is 7x, is that the same for these?
Thanks.
7x :)
Post by: 64rky on Wed, 13 January 2016, 07:52:29
This is such a n00b question n, but: could someone tell me if the Winkeyless space bar is 7x or 6.25x? On my cherry board it is 7x, is that the same for these?
Thanks.
7x :)
Much thanking :)
Post by: missalaire on Wed, 13 January 2016, 14:19:37
Post by: 64rky on Wed, 13 January 2016, 16:10:35
Post by: Steezus on Wed, 13 January 2016, 16:11:05
Does the Orion have RGB SMD's or are they just plain white? The pics sow multiple color underlighting.
They're RGB, programmed through the O2D keymapper. :thumb:
Post by: FrostyToast on Wed, 13 January 2016, 16:11:27
Does the Orion have RGB SMD's or are they just plain white? The pics sow multiple color underlighting.Rgb
Post by: 64rky on Wed, 13 January 2016, 16:13:26
Does the Orion have RGB SMD's or are they just plain white? The pics sow multiple color underlighting.Rgb
So you can switch colors? Set a key to switch cars :D
Post by: Steezus on Wed, 13 January 2016, 16:15:50
Does the Orion have RGB SMD's or are they just plain white? The pics sow multiple color underlighting.Rgb
So you can switch colors? Set a key to switch cars :D
You're not able to program a key to change colors iirc, however you can control the color of each SMD RGB LED in the keymapper and even have them rotate colors.
Post by: orcinus on Wed, 13 January 2016, 19:39:50
My bounce issue is spreading. Now it's not just space anymore, it's other (random) keys.
It doesn't happen VERY often, but it happens.
I'm guessing default debounce is extremely conservative, possibly to get the poll rate as high as possible.
What switches are you using? Related, how did you fix the spacebar stickiness? I've got some friction with my spacebar stab and didn't notice until after I had already soldered on all my switches. Hoping it just goes away over time.
Cherry 62g clears, lubed, stickered.
I've fixed the spacebar stickyness by a combination of things, so it's hard to tell which one had the most effect...
The stabs are the main cause - the stab holes are spaced a tiny amount off, causing the stems of the stabs to chafe the edge of the stab casing. I've bent the stab wire ends a little inwards (like this /___\, but very very slightly), then mounted, removed, remounted, removed the wire a few times so the wire anchors loosen up a bit (careful not to break them). Finally, i lubed both, the inside wall of the casing of the stabs and the anchors.
I'll try to do some horrible ASCII "art", bear with me.
Let's say this is your setup:
Code: [Select]
stab switch stab
v---stem v---casing
[+] [+] [+]
--- ---
^---wire anchor
The bits you need to lube are the wire anchors and the RIGHT wall of the LEFT stab casing, and the LEFT wall of the LEFT stab casing (in other words - the "inside" walls). Hope that makes sense.
You can do all of these things without unsoldering or removing anything. You can wiggle the wire out by poking it out of the anchors through the holes, then use tweezers to get it out through the "front" from under the plate. Make sure to use plastic tools. Wrap the tweezers in plastic tape or something so you don't scratch your keyboard.
Post by: orcinus on Wed, 13 January 2016, 19:40:31
Got my hands on an alps pcb/plate but I have no idea which diodes I need. I have some 1N4148 smd diodes leftover from my ergodox build, would those work?
Diodes are pretty much interchangeable for this application, as long as they fit the footprint.
Just mind the polarity.
Post by: Pemdas on Wed, 13 January 2016, 20:00:29
Got my hands on an alps pcb/plate but I have no idea which diodes I need. I have some 1N4148 smd diodes leftover from my ergodox build, would those work?
Diodes are pretty much interchangeable for this application, as long as they fit the footprint.
Just mind the polarity.
Thanks! That's great news one less part I have to order/find! Just gotta source some good alps switches now :p
Post by: orcinus on Wed, 13 January 2016, 20:04:19
You're not able to program a key to change colors iirc, however you can control the color of each SMD RGB LED in the keymapper and even have them rotate colors.
Correct, but incomplete.
You can't program a key to change colors directly (in the sense of tweaking RGB values from the keyboard itself), but you can make the whole backlight a single color and then step through multiple colors (specified in 02D keymapper) back and forth using the RGB + and RGB - keys. Don't ask me how, i played with it and forgot the exact steps. You need to find the right mode first using RGB Mode key, then RGB +/- step through the colors. I *think* you have to hit Change Lock first, but i might've misremebered.
Interesting tidbit - it seems you can change the maximum USB current limit of the keyboard in the Control Mode (from default 500mA).
Post by: Steezus on Wed, 13 January 2016, 20:07:27
You're not able to program a key to change colors iirc, however you can control the color of each SMD RGB LED in the keymapper and even have them rotate colors.
Correct, but incomplete.
You can't program a key to change colors directly (in the sense of tweaking RGB values from the keyboard itself), but you can make the whole backlight a single color and then step through multiple colors (specified in 02D keymapper) back and forth using the RGB + and RGB - keys. Don't ask me how, i played with it and forgot the exact steps. You need to find the right mode first using RGB Mode key, then RGB +/- step through the colors. I *think* you have to hit Change Lock first, but i might've misremebered.
Interesting tidbit - it seems you can change the maximum USB current limit of the keyboard in the Control Mode (from default 500mA).
Ah yeah I forgot about that, it's quite tricky to work. I have those keys programmed on my second layer but when I attempt to change the color(currently at solid red) all it does is flash the RGB LEDs but does nothing else(color stays the same).
Post by: 64rky on Wed, 13 January 2016, 21:00:09
You're not able to program a key to change colors iirc, however you can control the color of each SMD RGB LED in the keymapper and even have them rotate colors.
Correct, but incomplete.
You can't program a key to change colors directly (in the sense of tweaking RGB values from the keyboard itself), but you can make the whole backlight a single color and then step through multiple colors (specified in 02D keymapper) back and forth using the RGB + and RGB - keys. Don't ask me how, i played with it and forgot the exact steps. You need to find the right mode first using RGB Mode key, then RGB +/- step through the colors. I *think* you have to hit Change Lock first, but i might've misremebered.
Interesting tidbit - it seems you can change the maximum USB current limit of the keyboard in the Control Mode (from default 500mA).
Ah yeah I forgot about that, it's quite tricky to work. I have those keys programmed on my second layer but when I attempt to change the color(currently at solid red) all it does is flash the RGB LEDs but does nothing else(color stays the same).
As a programmer, this excites me, once my board is assembled, I will be tinkering until I get this working :)
If it works I'll put the steps up here...
Post by: orcinus on Wed, 13 January 2016, 21:20:44
Ah yeah I forgot about that, it's quite tricky to work. I have those keys programmed on my second layer but when I attempt to change the color(currently at solid red) all it does is flash the RGB LEDs but does nothing else(color stays the same).
Yeah, it did that for me too, then i got it to cycle to the next color by doing *something*, but promptly forgot what exactly the next day. I'm keeping it the same fixed pattern all the time anyways (amber on the sides, white everywhere else), so i'm not too motivated to go exploring again :D
Post by: orcinus on Wed, 20 January 2016, 13:05:37
Sorry for the (semi-)necro.
Post by: Steezus on Wed, 20 January 2016, 13:12:17
This place sure went quiet all of a sudden ;D
Sorry for the (semi-)necro.
I'm pretty sure the group buy is all finished up now. The only thing left is for people to leave posts asking for somebody to sell their board.
Post by: E3E on Wed, 20 January 2016, 13:13:16
This place sure went quiet all of a sudden ;D
Sorry for the (semi-)necro.
It was due to the Octagon v2 GB coming into the fray.It siphoned most if no all the attention away from this thread. 91 orders. Insane!
Post by: trevorlolo on Wed, 20 January 2016, 21:08:38
Post by: E3E on Wed, 20 January 2016, 21:27:44
Hello, I just saw this group buy and apparently I've missed it - is it true that the next GB for this keyboard is next year??
Yes, that is true, in a sense. The group buy next year will be for the Orion v3, so the next iteration.
So, it might be worth it to wait, but if not, I'm sure you could find someone who'd be willing to sell their board to you.
Post by: Steezus on Wed, 20 January 2016, 22:21:21
I'm sure you could find someone who'd be willing to sell their board to you.
I'm not so sure about that, the boards are rather hard to get.
Post by: lawlz_xD on Thu, 21 January 2016, 02:56:21
https://www.reddit.com/r/mechmarket/comments/41xchf/aushclearance_orion_v2_bolt_modded_model_m/
Post by: asdfjkl36 on Thu, 21 January 2016, 03:08:51
There was one that was recently posted on r/mechmarket and got snatched up within minutes. It sold for $600 USD...
https://www.reddit.com/r/mechmarket/comments/41xchf/aushclearance_orion_v2_bolt_modded_model_m/
Keep in mind that's an assembled board and is pretty much what the guy paid for if i can do math correctly.
Post by: ika on Thu, 21 January 2016, 03:17:33
There was one that was recently posted on r/mechmarket and got snatched up within minutes. It sold for $600 USD...
https://www.reddit.com/r/mechmarket/comments/41xchf/aushclearance_orion_v2_bolt_modded_model_m/
Keep in mind that's an assembled board and is pretty much what the guy paid for if i can do math correctly.
Roughly $440 for the base board, then another $80 for the Zealios, another maybe $50 for the keyset, $10-30 (wtf) for the MX Lock, then SIP sockets and soldering + assembly. $600 is right on the money.
Post by: ika on Thu, 21 January 2016, 03:36:12
[오리온V2]
인디케이터
ESC 우측은 위에서부터 넘락, 캡스락, 스크롤락을 표시하며,
방향키 위의 인디케이터는, 좌측부터 4개는 레이어(또는 펑션키 상태), 우측 1개는 인디케이터로 작동합니다.
레이어의 경우 순서대로 1, 2, 3, 4 레이어 변경시 점등되며,
멀티펑션키 사용시, 설정된 펑션키에 해당하는 부분이 꺼지는(반전) 방법으로 표현됩니다.
예) 토글 레이어로 3번 레이어 설정 (3번이 켜짐)
LED : 0 0 1 0 0
예) 멀티 펑션키를 3번 누른채 유지 (3번만 꺼짐, 인디케이터는 상태에 따라 다름)
LED : 1 1 0 1 0
스위치 LED 및 RGB LED의 최대 밝기 자동 조절
USB 2.0의 500mA 내에서 스위치 LED 점등 상태, 이펙트 상태, RGB의 색상에 따른 밝기를 자동으로 제어
스위치 LED의 경우 바이패스 모드를 제외하고 멀티LED 사용 불가
바이패스 모드 설정시 RGB의 밝기에 영향이 있습니다. (스위치 LED 전체 OFF시 최대, 전체 ON시 최소 밝기)
바이패스 모드는 스위치 LED 모드에만 영향이 있습니다.
최대 전력 설정
LED(RGB 포함)에 사용 가능한 최대 전류값을 설정할 수 있는 기능으로,
해당 기능 설정시 작동 및 고장에 대한 모든 책임은 사용자 본인에게 귀속됩니다.
사용하는 기기(PC 등)의 USB 출력 전류가 넉넉한 경우에만 설정하시기 바랍니다.
설정 예)스위치 LED 바이패스 상태로 전체 점등(멀티 LED 사용)한 상태에서 RGB LED 밝기를 확보할 수 있습니다.
> 설정 방법
컨트롤 모드 진입 후,
S C M Enter 입력,
500~900 사이의 숫자를 천천히 누름 (기본 500)
컨트롤 모드 누름 (저장)
ESC로 컨트롤 모드 종료
작동 오류나 끊어짐 발생시 기본 500으로 재설정 후 사용
키보드 인식 후 LED Down 키를 누르면 LED 정지
이후 전력 설정 변경
Post by: rainb1ood on Thu, 21 January 2016, 03:43:04
I mapped "FN1" to function key I desired then copied Layer FN4 to Layer FN1.
Then you press Function key + Esc (LED Ctrl), indicator light should blink located above arrow key
Press function key + F1-4 or which section you prefer.
Press function key + Up or function key + Down to change brightness
This is the guide that helped me or kinda of "ELI5" me to 02D:
http://www.adamfalwell.com/projects/octagon/assets/lightsaverv2-layout-editing-and-updating-tutorial.pdf
Post by: ika on Thu, 21 January 2016, 03:46:00
Heres what I did:
I mapped "FN1" to function key I desired then copied Layer FN4 to Layer FN1.
Then you press Function key + Esc (LED Ctrl), indicator light should blink located above arrow key
Press function key + F1-4 or which section you prefer.
Press function key + Up or function key + Down to change brightness
Ah there's the part that doesn't work for me. LED Down just turns LEDs off and LED Up just turns them on. I figured out how all the LED sections work and the cycle modes but I'm not able to control brightness through the default keymap keys.
EDIT: oh wait, I think playing around in the LED Ctrl mode might have done something! Will have to do more experimenting...
edit2: yeah that works! thanks!
EDIT3: for reference, LED Ctrl (and Control Mode) turn on the fifth indicator light, and once in LED Ctrl mode, it turns the LEDs off and you have to turn them back on then adjust brightness from there. Same with the RGB mode.
Post by: rainb1ood on Thu, 21 January 2016, 03:46:48
Since you are using the default mapping, you just have to map one function to test it.
Map "FN4" to a key you prefer (bottom row keys etc).
The default LED controls are on Layer FN4. Pressing and holding a key that is mapped to "FN4" will let you use Layer FN4.
Post by: trevorlolo on Thu, 21 January 2016, 07:27:28
welp I'll take it as an extra period for me to save up then ;(Hello, I just saw this group buy and apparently I've missed it - is it true that the next GB for this keyboard is next year??
Yes, that is true, in a sense. The group buy next year will be for the Orion v3, so the next iteration.
So, it might be worth it to wait, but if not, I'm sure you could find someone who'd be willing to sell their board to you.
Post by: E3E on Thu, 21 January 2016, 13:01:03
You need to enter the LED Ctrl mode first in order to get up and down arrow to work for brightness.
Since you are using the default mapping, you just have to map one function to test it.
Map "FN4" to a key you prefer (bottom row keys etc).
The default LED controls are on Layer FN4. Pressing and holding a key that is mapped to "FN4" will let you use Layer FN4.
I still don't get how these work for my Duck Eagle, I mean... I've used LED control and LED UP and DOWN to no effect, LED CTRL and LED DOWN both turn off the LED; pressing LED control again turns them on again. LED UP does nothing except also turn the LEDs on if they are off after pressing LED DOWN.
In other words, the brightness doesn't seem to work! I'm fine with this on my Eagle as it's pretty much just right for me, but really wish I could adjust it on my Octagon.
Post by: rainb1ood on Thu, 21 January 2016, 13:03:25
Maybe it uses different combination to change brightnessYou need to enter the LED Ctrl mode first in order to get up and down arrow to work for brightness.
Since you are using the default mapping, you just have to map one function to test it.
Map "FN4" to a key you prefer (bottom row keys etc).
The default LED controls are on Layer FN4. Pressing and holding a key that is mapped to "FN4" will let you use Layer FN4.
I still don't get how these work for my Duck Eagle, I mean... I've used LED control and LED UP and DOWN to no effect, LED CTRL and LED DOWN both turn off the LED; pressing LED control again turns them on again. LED UP does nothing except also turn the LEDs on if they are off after pressing LED DOWN.
In other words, the brightness doesn't seem to work! I'm fine with this on my Eagle as it's pretty much just right for me, but really wish I could adjust it on my Octagon.
Edit: scratch that. You already mentioned the functions itself.
I'll check on it more later when I get home
Post by: Steezus on Sat, 23 January 2016, 20:36:47
Post by: omgar on Sun, 24 January 2016, 16:25:08
I have an acrylic angled bottom that I'm willing to same. Retail price + shipping.
I'm interested! Can you PM me?
Post by: rainb1ood on Mon, 01 February 2016, 17:41:20
Or elton/anyone: is it possible to still buy a plate from http:/kbd4u.co.kr ?
Post by: axtran on Mon, 01 February 2016, 23:39:51
Post by: filphil on Tue, 02 February 2016, 00:58:46
This is kind of an odd question, but I have the MX PCB leftover from this GB, and was wondering if anyone knows if the switch placements line up with the GON PCB? I was hoping to buy a Crystal TKL housing and use the PCB... ;)
I was considering approaching SEAL for custom wood work. Maybe you'd like to give that a try over your gon option if no one comes forward and answers your question.
Post by: axtran on Tue, 02 February 2016, 01:04:04
This is kind of an odd question, but I have the MX PCB leftover from this GB, and was wondering if anyone knows if the switch placements line up with the GON PCB? I was hoping to buy a Crystal TKL housing and use the PCB... ;)
I was considering approaching SEAL for custom wood work. Maybe you'd like to give that a try over your gon option if no one comes forward and answers your question.
I asked WKL about the new b.87 housing and Hojin actually knew--no compatibility. :(
Post by: filphil on Tue, 02 February 2016, 01:20:41
This is kind of an odd question, but I have the MX PCB leftover from this GB, and was wondering if anyone knows if the switch placements line up with the GON PCB? I was hoping to buy a Crystal TKL housing and use the PCB... ;)
I was considering approaching SEAL for custom wood work. Maybe you'd like to give that a try over your gon option if no one comes forward and answers your question.
I asked WKL about the new b.87 housing and Hojin actually knew--no compatibility. :(
https://geekhack.org/index.php?topic=75471.0
Well... Maybe seal can help then. I like what was posted but have no information beyond what's posted in that thread.
Post by: Frizer on Tue, 02 February 2016, 13:44:09
(https://farm2.staticflickr.com/1485/24752018496_a11e8a326b.jpg) (https://flic.kr/p/DHfyKA)
(https://farm2.staticflickr.com/1643/24482722410_e921ecc39f.jpg) (https://flic.kr/p/DismpC)
Post by: filphil on Thu, 04 February 2016, 15:47:02
(http://i.imgur.com/3wFFw2r.jpg)
Post by: E3E on Thu, 04 February 2016, 16:01:30
Went to texas for PAX South this past weekend and found this when I went to NASA.Show Image(http://i.imgur.com/3wFFw2r.jpg)
Dude, THAT is so sick and so fitting!
It'd work for both the Orion and the Mira, though... Well, the Mira...
SPEAK NO EVIL, GENTS!
That patch is fantastic though. If you ever got a custom hard case done by intelli like I have for my Octagon v1, you should definitely consider having them slap that patch on! I got a Jukebox patch made for my Octagon to go with the theme!
(http://i.imgur.com/UFYuRfS.jpg)
Post by: filphil on Thu, 04 February 2016, 16:22:57
That's a good idea on the case. I'll have to get in touch with intelli
Post by: romevi on Thu, 04 February 2016, 16:25:23
Yeah man. I saw it and immediately picked it up.
That's a good idea on the case. I'll have to get in touch with intelli
Hmm... I wonder if he'll do a case with the Jane logo.
Post by: E3E on Thu, 04 February 2016, 16:39:29
Yeah man. I saw it and immediately picked it up.
That's a good idea on the case. I'll have to get in touch with intelli
Hmm... I wonder if he'll do a case with the Jane logo.
Most certainly. In my usual fashion of perusing endlessly on the topic of something I want to purchase, I read up a ton of info on his cases, and patches were always offered as a custom option. Just get one made and then send it in and they can sew it right on!
I want to get a case made for my Hammer Alps board, but I'd rather put a stenciled decal [HAMMER] on it with some fabric paint or something. I really don't know how well it'd work and I have an HHKB case that fits it perfectly for now, but it's an idea I have. I'll have to talk to them about it!
When it comes to patches, you'll just have to source them from a company that can make custom patches for you! I used http://www.mutinyshop.com/ and they were REALLY fantastic and helpful the entire way through.
Post by: xondat on Fri, 05 February 2016, 04:58:49
Went to texas for PAX South this past weekend and found this when I went to NASA.Show Image(http://i.imgur.com/3wFFw2r.jpg)
Dude, THAT is so sick and so fitting!
It'd work for both the Orion and the Mira, though... Well, the Mira...
SPEAK NO EVIL, GENTS!
That patch is fantastic though. If you ever got a custom hard case done by intelli like I have for my Octagon v1, you should definitely consider having them slap that patch on! I got a Jukebox patch made for my Octagon to go with the theme!Show Image(http://i.imgur.com/UFYuRfS.jpg)
How have I not seen this before? Stunning.
Post by: rainb1ood on Fri, 05 February 2016, 05:39:01
E3E I thought I might be able to figure it out but for some reason, my Octagon doesn't want to let me control the LEDs like I used to do it before, I can only go to LED Ctrl mode and lets me turn it on and off and no brightness, I can't even turn it on without going to LED ctrl first, this is weird, I've tried reflashing back to default then back to my custom mapping. Outside of LED Ctrl it used to let me control the LED effects, brightness, etc.
I still don't get how these work for my Duck Eagle, I mean... I've used LED control and LED UP and DOWN to no effect, LED CTRL and LED DOWN both turn off the LED; pressing LED control again turns them on again. LED UP does nothing except also turn the LEDs on if they are off after pressing LED DOWN.
In other words, the brightness doesn't seem to work! I'm fine with this on my Eagle as it's pretty much just right for me, but really wish I could adjust it on my Octagon.
Post by: 64rky on Fri, 05 February 2016, 06:43:18
Went to texas for PAX South this past weekend and found this when I went to NASA.Show Image(http://i.imgur.com/3wFFw2r.jpg)
Dude, THAT is so sick and so fitting!
It'd work for both the Orion and the Mira, though... Well, the Mira...
SPEAK NO EVIL, GENTS!
That patch is fantastic though. If you ever got a custom hard case done by intelli like I have for my Octagon v1, you should definitely consider having them slap that patch on! I got a Jukebox patch made for my Octagon to go with the theme!Show Image(http://i.imgur.com/UFYuRfS.jpg)
Tell me more about this padded keyboard case.
Post by: E3E on Fri, 05 February 2016, 18:32:40
Tell me more about this padded keyboard case.
Well, here's the main thread on them! https://geekhack.org/index.php?topic=56253.300
I saw these on Massdrop once and was like "OMG I NEED ONE FOR MY OCTAGON," so I put up a classified for one here on GeekHack and also on /r/mechmarket, and then intelli chimed in being all NOPE, "there's only been like 1 or 2 of these made for 75%, so you probably won't find one," so eventually I put 2 + 2 together and realized he offered the service for these.
So then came the massive brainstorming session. I bought my Octagon mainly because of Jukebox, and I bought Jukebox mainly because of my Octagon. I thought they just went too well together, so I decided to base my case on the color scheme of Jukebox and rep it hardcore with a patch even!
Somewhere down the line, I thought it'd be sick to have a case for my Lightpad too and have it be a companion to the main case, since the Lightpad really does flesh out the 75% Octagon to a 100%, more or less.
The artisan intelli works with really appreciated the creative ideas and back and forth brainstorming and correspondence we had. Even got a thank you letter with my cases when they were done!
I love them, really. They fit together so well. Makes me wonder if I should really Alps my Lightpad or not.
Oh well, the v2 is around the horizon, so one can be Alps and the other can be MX. :P
Post by: elton5354 on Fri, 05 February 2016, 20:19:50
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
Post by: SavvyBird on Fri, 05 February 2016, 20:22:34
Post by: romevi on Fri, 05 February 2016, 20:23:54
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.^-^
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
^-^ ^-^
Post by: Auxo on Fri, 05 February 2016, 20:24:06
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
we talking bout the split kb?
Post by: appleonama on Fri, 05 February 2016, 20:24:51
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.sweet thanks for the news ;D
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
Post by: romevi on Fri, 05 February 2016, 20:25:06
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
we talking bout the split kb?
No, he's talking about the v2 number pad. The split keyboard is by Vermillion/Zefyr, a completely different guy.
Post by: FrostyToast on Fri, 05 February 2016, 20:26:09
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
we talking bout the split kb?
Always
Post by: E3E on Fri, 05 February 2016, 20:46:52
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
With out a doubt a must have, and if it is going to be different in form than the Lightpad, I might not feel so bad changing my original to Alps.
Will it use a new form factor or continue the same PCB design similarly to the Duck Mini > Duck Eagle/Viper?
Sorry, I understand you want to keep this under wraps, haha.
Post by: William_S_Jones on Sun, 07 February 2016, 01:04:18
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
I'm looking forward to this new board & hope that I'll be able to get it!
Post by: xondat on Sun, 07 February 2016, 03:07:42
I don't want to leak too much about the next keypad, but I will say it will not be your traditional keypad. It will be very special, one of the kind keypad with many functions.
The design is not even made yet, so it possibly won't be in the next group buy, rather sometime this year..possibly.
Another keypad for a TKL Korean custom? :confused: :confused:
Post by: Frizer on Sun, 07 February 2016, 04:29:58
(https://farm2.staticflickr.com/1499/24574710070_4b670ccd43.jpg) (https://flic.kr/p/DrzP8L)
Post by: xondat on Sun, 07 February 2016, 14:39:20
Starting to get to grips with it now, love this board
(https://farm2.staticflickr.com/1499/24574710070_4b670ccd43.jpg) (https://flic.kr/p/DrzP8L)
PLEASE attend a UK meetup with this. Also a tripod wouldn't hurt ;)
If you ever sell it, hit me up.
Post by: E3E on Sun, 07 February 2016, 14:49:24
This is the only TKL I'd ever bother with, haha.
Post by: filphil on Sun, 07 February 2016, 15:13:33
If anyone would ever want to let go of a full aluminum Orion v2 with an Alps plate and PCB, hit me up.
This is the only TKL I'd ever bother with, haha.
That's a super tight request. Although it IS the sole exception for a TKL I do wish you luck. :thumb:
Post by: E3E on Sun, 07 February 2016, 15:17:18
If anyone would ever want to let go of a full aluminum Orion v2 with an Alps plate and PCB, hit me up.
This is the only TKL I'd ever bother with, haha.
That's a super tight request. Although it IS the sole exception for a TKL I do wish you luck. :thumb:
Oh, I know. I know. I don't plan on it ever being fulfilled, trust me. :P
Post by: filphil on Sun, 07 February 2016, 21:18:55
Post by: FrostyToast on Sun, 07 February 2016, 21:39:30
If anyone would ever want to let go of a full aluminum Orion v2 with an Alps plate and PCB, hit me up.
This is the only TKL I'd ever bother with, haha.
That's a super tight request. Although it IS the sole exception for a TKL I do wish you luck. :thumb:
Oh, I know. I know. I don't plan on it ever being fulfilled, trust me. :P
Slushi has 1 of 5 existing ALPS kits since he took my order.
Post by: SavvyBird on Sun, 07 February 2016, 21:48:51
Post by: Steezus on Sun, 07 February 2016, 21:49:36
Anyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
Post by: SavvyBird on Sun, 07 February 2016, 21:52:23
Anyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
Post by: Steezus on Sun, 07 February 2016, 21:56:36
Anyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
I just mean in the sense that it's very rare that somebody will approach you to sell the board. If they want to sell it they'll put it up on classifieds or contact a friend first.
Post by: SavvyBird on Sun, 07 February 2016, 22:00:16
Anyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
I just mean in the sense that it's very rare that somebody will approach you to sell the board. If they want to sell it they'll put it up on classifieds or contact a friend first.
:-[ but but but this is how I got a viper and eagle 2 years back. I know its rare but it doesn't hurt to ask here.
Post by: Steezus on Sun, 07 February 2016, 22:01:30
Anyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
I just mean in the sense that it's very rare that somebody will approach you to sell the board. If they want to sell it they'll put it up on classifieds or contact a friend first.
:-[ but but but this is how I got a viper and eagle 2 years back. I know its rare but it doesn't hurt to ask here.
It doesn't hurt to ask and I don't mean to discourage you. It's just that a lot of people do the same I never see anything come of it.
Post by: SavvyBird on Sun, 07 February 2016, 22:03:03
we need a revolution, keyboards for everyone >:DAnyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
I just mean in the sense that it's very rare that somebody will approach you to sell the board. If they want to sell it they'll put it up on classifieds or contact a friend first.
:-[ but but but this is how I got a viper and eagle 2 years back. I know its rare but it doesn't hurt to ask here.
It doesn't hurt to ask and I don't mean to discourage you. It's just that a lot of people do the same I never see anything come of it.
only if put in an order before I left... I wish I knew it was going to take 8+ months :'(
Post by: Steezus on Sun, 07 February 2016, 22:08:31
we need a revolution, keyboards for everyone >:DAnyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
I just mean in the sense that it's very rare that somebody will approach you to sell the board. If they want to sell it they'll put it up on classifieds or contact a friend first.
:-[ but but but this is how I got a viper and eagle 2 years back. I know its rare but it doesn't hurt to ask here.
It doesn't hurt to ask and I don't mean to discourage you. It's just that a lot of people do the same I never see anything come of it.
only if put in an order before I left... I wish I knew it was going to take 8+ months :'(
Haha I'm all for that revolution. It's crazy how this GB took but it's worth it. I really liked my Orion v2 but I had another board that I was hunting down become available.
Post by: Pemdas on Sun, 07 February 2016, 22:11:55
If anyone would ever want to let go of a full aluminum Orion v2 with an Alps plate and PCB, hit me up.
This is the only TKL I'd ever bother with, haha.
That's a super tight request. Although it IS the sole exception for a TKL I do wish you luck. :thumb:
Oh, I know. I know. I don't plan on it ever being fulfilled, trust me. :P
Slushi has 1 of 5 existing ALPS kits since he took my order.
I actually bought that alps kit from slushi so he no longer has it :thumb:
Just need to find a donor boards with greens to bring to life :cool:
Post by: romevi on Sun, 07 February 2016, 22:16:40
Anyone willing to part with their keyboard please let me know ^-^
That's usually not how it works but good luck.
:( what? i edit it to sell
I just mean in the sense that it's very rare that somebody will approach you to sell the board. If they want to sell it they'll put it up on classifieds or contact a friend first.
:-[ but but but this is how I got a viper and eagle 2 years back. I know its rare but it doesn't hurt to ask here.
It doesn't hurt to ask and I don't mean to discourage you. It's just that a lot of people do the same I never see anything come of it.
Definitely doesn't hurt to ask. It's not optimal, but I've seen a few things trade off this way. I've even gotten a few keysets from previous GBs by asking. ;)
Post by: SavvyBird on Sun, 07 February 2016, 22:25:55
Post by: romevi on Sun, 07 February 2016, 22:39:48
I can consider throwing my topre candy corn or topre drunken + monies if you're into that sort thing :rolleyes:
No... You can always get an Orion later. How often can you get those CC's?
Post by: SavvyBird on Sun, 07 February 2016, 22:50:58
I can consider throwing my topre candy corn or topre drunken + monies if you're into that sort thing :rolleyes:
No... You can always get an Orion later. How often can you get those CC's?
true :'(
Post by: slushi on Tue, 09 February 2016, 22:11:17
Post by: ika on Tue, 09 February 2016, 22:32:40
Is anyone having issues running the keymapper? I am running Windows 10 Pro and the old 1.6.456 keymapper works with it but not the 1.7.596b for the Orion V2.
On Win10 and using the v1.7.596b mapper just fine. What's your error?
Post by: slushi on Tue, 09 February 2016, 22:33:42
Post by: orcinus on Wed, 10 February 2016, 18:52:57
I ended up never changing the debounce.
It somehow fixed itself over time.
I guess the switches + stabs broke in after a while.
Post by: filphil on Wed, 10 February 2016, 21:16:47
I have a MX steel plate to trade for an aluminum plate if anyone is willing.
Can sell this(steel plate) now. Plastic plate is where it's at.
Post by: Steezus on Wed, 10 February 2016, 21:19:41
Plastic plate is where it's at.
Hell yeah it is! ;)
Post by: rainb1ood on Thu, 11 February 2016, 19:08:32
After weeks of use, I kinda prefer the stainless steel, although the tactile is most felt on the plastic plate.
WTB stainless steel plate
Post by: romevi on Thu, 11 February 2016, 19:48:30
I have plastic plate on Orion v2 and stainless steel plate on Octagon
After weeks of use, I kinda prefer the stainless steel, although the tactile is most felt on the plastic plate.
WTB stainless steel plate
What switch do you use on the stainless steel?
Post by: rainb1ood on Thu, 11 February 2016, 21:11:59
Cherry ergo clear on stainless steelI have plastic plate on Orion v2 and stainless steel plate on Octagon
After weeks of use, I kinda prefer the stainless steel, although the tactile is most felt on the plastic plate.
WTB stainless steel plate
What switch do you use on the stainless steel?
Zealio tactile on plastic
Post by: E3E on Thu, 11 February 2016, 23:35:20
Cherry ergo clear on stainless steelI have plastic plate on Orion v2 and stainless steel plate on Octagon
After weeks of use, I kinda prefer the stainless steel, although the tactile is most felt on the plastic plate.
WTB stainless steel plate
What switch do you use on the stainless steel?
Zealio tactile on plastic
I certainly hope I don't regret aluminum for my vintage MX white switches on the Octagon v2! I've never used Aluminum before, but MX greens sounded like crap on the Octagon v1. To be fair, vintage whites sound so much nicer. I put them in Zealio housings and they are more consistent. Slightly louder (stock housings had them a bit inconsistent and practically mute, which was intriguing), but still quiet and refined. They remind me of Alps a bit. They sound icky with SA caps, but sounded great with Cherry profile PBT. I'm hoping they'll sound good with GMK, though I'm thinking that GMK SNES might not ever hit MQO. I hope I'm wrong about that, because that is THE set I want for the Octagon v2.
Otherwise, I'm gonna have to try and find a PBT set I can dye, haha.
Also, I keep forgetting, but I wanted to thank you for your tips on brightness adjustment, man, that really helped! I can't find an LED scheme that goes well with Jukebox though. :/
Post by: rainb1ood on Fri, 12 February 2016, 17:31:54
I certainly hope I don't regret aluminum for my vintage MX white switches on the Octagon v2! I've never used Aluminum before, but MX greens sounded like crap on the Octagon v1. To be fair, vintage whites sound so much nicer. I put them in Zealio housings and they are more consistent. Slightly louder (stock housings had them a bit inconsistent and practically mute, which was intriguing), but still quiet and refined. They remind me of Alps a bit. They sound icky with SA caps, but sounded great with Cherry profile PBT. I'm hoping they'll sound good with GMK, though I'm thinking that GMK SNES might not ever hit MQO. I hope I'm wrong about that, because that is THE set I want for the Octagon v2.
Otherwise, I'm gonna have to try and find a PBT set I can dye, haha.
Also, I keep forgetting, but I wanted to thank you for your tips on brightness adjustment, man, that really helped! I can't find an LED scheme that goes well with Jukebox though. :/
No problem! Glad that helped. I think aluminum could be a safe choice in terms of switch feel and sound.
Post by: aznairjordan on Sun, 14 February 2016, 00:58:30
Post by: E3E on Sun, 14 February 2016, 01:20:15
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
Post by: aznairjordan on Sun, 14 February 2016, 01:37:02
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
Post by: E3E on Sun, 14 February 2016, 01:44:27
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
Post by: aznairjordan on Sun, 14 February 2016, 01:52:53
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
I am able to connect and upload firmware like the custom orion v2 preset one, but when the firmware upload box comes up I get a memory write error, use debug for more info. message. None of the keys work at this point,
Full message says
3-2. frmware write...
Checking memory from 0x0 to 0x6FFF... Empty.
0% 100% Programming 0x7000 bytes
...
[ X Error
Memory write error, use debug for more info.
3-3. restart device...
Firmware upload done.
press any key to continue...
Post by: E3E on Sun, 14 February 2016, 02:34:59
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
I am able to connect and upload firmware like the custom orion v2 preset one, but when the firmware upload box comes up I get a memory write error, use debug for more info. message. None of the keys work at this point,
Full message says
3-2. frmware write...
Checking memory from 0x0 to 0x6FFF... Empty.
0% 100% Programming 0x7000 bytes
...
[ X Error
Memory write error, use debug for more info.
3-3. restart device...
Firmware upload done.
press any key to continue...
Oh, hmmm... I have not run into this issue before. :-X I wish I could be more assistance to you, but hopefully someone else around here can help you. I can't imagine that you've bricked your keyboard. There has to be a way to resolve this issue. :(
Post by: filphil on Sun, 14 February 2016, 02:47:15
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
I am able to connect and upload firmware like the custom orion v2 preset one, but when the firmware upload box comes up I get a memory write error, use debug for more info. message. None of the keys work at this point,
Full message says
3-2. frmware write...
Checking memory from 0x0 to 0x6FFF... Empty.
0% 100% Programming 0x7000 bytes
...
[ X Error
Memory write error, use debug for more info.
3-3. restart device...
Firmware upload done.
press any key to continue...
Try renaming the hex file to something simple .hex and upload it using the FLIP program. After that I've got nothing for ya.
Post by: aznairjordan on Sun, 14 February 2016, 02:50:58
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
I am able to connect and upload firmware like the custom orion v2 preset one, but when the firmware upload box comes up I get a memory write error, use debug for more info. message. None of the keys work at this point,
Full message says
3-2. frmware write...
Checking memory from 0x0 to 0x6FFF... Empty.
0% 100% Programming 0x7000 bytes
...
[ X Error
Memory write error, use debug for more info.
3-3. restart device...
Firmware upload done.
press any key to continue...
Try renaming the hex file to something simple .hex and upload it using the FLIP program. After that I've got nothing for ya.
do you mind linking me to the flip program? or more so how to use it?
Post by: filphil on Sun, 14 February 2016, 03:04:07
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
I am able to connect and upload firmware like the custom orion v2 preset one, but when the firmware upload box comes up I get a memory write error, use debug for more info. message. None of the keys work at this point,
Full message says
3-2. frmware write...
Checking memory from 0x0 to 0x6FFF... Empty.
0% 100% Programming 0x7000 bytes
...
[ X Error
Memory write error, use debug for more info.
3-3. restart device...
Firmware upload done.
press any key to continue...
Try renaming the hex file to something simple .hex and upload it using the FLIP program. After that I've got nothing for ya.
do you mind linking me to the flip program? or more so how to use it?
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
Post by: aznairjordan on Sun, 14 February 2016, 03:31:57
I finally got my board built and running. My spacebar is a bit mushy. Is the only way fix this issue to put a heavy spring in it? Also, I can't seem control the led brightness. It just turns the leds on or off when I use led ctrl..
Super tight fitting caps can cause a somewhat mushy feel if you press the stablizer mounts down as far as they can go. I've seen this on Gateron PBT space bars. I forget if GMK had this issue.
I just flashed a firmware and I forgot to switch the B/S to the key to the left of it.. Now I can't flash anything onto it :( Did I really screw up badly? Or is there a fix for this?
From what I understand, it's not actually bound to Backspace itself, but simply the key in that position, and that cannot be altered through the firmware.
In otherwords, I think you should be fine. Just try holding the key down while plugging the board in again. Make sure you unplug the cable all the way first; I've done some lazy unplugs where I only barely disconnect the cable until I hear the disconnect sound from Windows, but that has proven to be a false positive at times.
I hope I've understood you correctly! Sorry if I've misinterpreted anything.
I am able to connect and upload firmware like the custom orion v2 preset one, but when the firmware upload box comes up I get a memory write error, use debug for more info. message. None of the keys work at this point,
Full message says
3-2. frmware write...
Checking memory from 0x0 to 0x6FFF... Empty.
0% 100% Programming 0x7000 bytes
...
[ X Error
Memory write error, use debug for more info.
3-3. restart device...
Firmware upload done.
press any key to continue...
Try renaming the hex file to something simple .hex and upload it using the FLIP program. After that I've got nothing for ya.
do you mind linking me to the flip program? or more so how to use it?
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
you have no idea how much i love you right now :) typed from my orion! now to figure out the damn leds..
Post by: filphil on Sun, 14 February 2016, 03:37:04
Glad we got one issue solved. I don't have leds yet so I can't help you on that front.
Post by: filphil on Tue, 16 February 2016, 01:06:28
(http://i.imgur.com/Lvci6vA.jpg)
Post by: VereChi on Tue, 16 February 2016, 03:38:10
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Where did u get this?
Looks Awesome
Post by: xondat on Tue, 16 February 2016, 07:24:59
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Is this a custom weight? :confused:
Post by: FrostyToast on Tue, 16 February 2016, 07:37:29
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Is this a custom weight? :confused:
Yes.
The aluminum bottom has space designed for a weight to be placed inside.
Post by: mrboovn on Tue, 16 February 2016, 09:22:52
From Orion v2's Group buy in South KoreaFinally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Where did u get this?
Looks Awesome
Post by: xondat on Tue, 16 February 2016, 12:34:52
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Is this a custom weight? :confused:
Yes.
The aluminum bottom has space designed for a weight to be placed inside.
Ah - always wondered what that hole was for, now that I know I feel quite stupid :p
Post by: 64rky on Tue, 16 February 2016, 13:01:08
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Is this a custom weight? :confused:
Yes.
The aluminum bottom has space designed for a weight to be placed inside.
Ah - always wondered what that hole was for, now that I know I feel quite stupid :p
So how do I get one?
Post by: FrostyToast on Tue, 16 February 2016, 13:12:35
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Is this a custom weight? :confused:
Yes.
The aluminum bottom has space designed for a weight to be placed inside.
Ah - always wondered what that hole was for, now that I know I feel quite stupid :p
So how do I get one?
Step one: learn Korean
Step two: find a Korean friend after quitting learning
Step three: cry that you missed the group buy and that you have no friends
Post by: 64rky on Tue, 16 February 2016, 13:21:20
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Is this a custom weight? :confused:
Yes.
The aluminum bottom has space designed for a weight to be placed inside.
Ah - always wondered what that hole was for, now that I know I feel quite stupid :p
So how do I get one?
Step one: learn Korean
Step two: find a Korean friend after quitting learning
Step three: cry that you missed the group buy and that you have no friends
Just ordered Rosetta Stone (Korean).
:thumb:
Post by: Steezus on Tue, 16 February 2016, 13:22:15
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Very nice filphil! I was about to pick one up myself but ended up selling my board. ;)
Post by: filphil on Tue, 16 February 2016, 18:14:15
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Very nice filphil! I was about to pick one up myself but ended up selling my board. ;)
I'd argue you've got a pretty good project in return for the board though!
Post by: Steezus on Tue, 16 February 2016, 18:31:53
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Very nice filphil! I was about to pick one up myself but ended up selling my board. ;)
I'd argue you've got a pretty good project in return for the board though!
Yeah haha I'd say it's a rather good trade, I'm hoping I won't regret it. Definitely a lot more work for this upcoming board but it should be worth it. :thumb:
Post by: Pemdas on Tue, 16 February 2016, 21:26:34
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
That looks so good but I guess you can't see it when it's installed in the board :(
Was this specific to the korean buys? Any reason it wasn't available in the geekhack groupbuy? I would've loved some extra heft to this board :p
Post by: filphil on Wed, 17 February 2016, 00:00:24
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Very nice filphil! I was about to pick one up myself but ended up selling my board. ;)
I'd argue you've got a pretty good project in return for the board though!
Yeah haha I'd say it's a rather good trade, I'm hoping I won't regret it. Definitely a lot more work for this upcoming board but it should be worth it. :thumb:
Idk how you walk around with those massive balls of yours. I'd **** myself desoldering and soldering that.
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
That looks so good but I guess you can't see it when it's installed in the board :(
Was this specific to the korean buys? Any reason it wasn't available in the geekhack groupbuy? I would've loved some extra heft to this board :p
I'm not sure of the history with the plate and the group buy. I can certainly ask. I've seen a few boards on kbdlab.co.kr with the plate though so it wasn't a one off.
Post by: Steezus on Wed, 17 February 2016, 00:07:24
Finally got one coming to meShow Image(http://i.imgur.com/Lvci6vA.jpg)
Very nice filphil! I was about to pick one up myself but ended up selling my board. ;)
I'd argue you've got a pretty good project in return for the board though!
Yeah haha I'd say it's a rather good trade, I'm hoping I won't regret it. Definitely a lot more work for this upcoming board but it should be worth it. :thumb:
Idk how you walk around with those massive balls of yours. I'd **** myself desoldering and soldering that.
Haha luckily I didn't need to desolder, it was never built after all these years. Luckily if something were to go wrong the PCBs are so basic that it'd be easy to follow the traces and jump a switch. I doubt that'll happen though. The only worrying thing is to solder the cable in the correct order especially when I'm swapping it to USB or else I could fry the PCB. My balls still aren't as big as originally thought. ;)
Post by: ctrlX on Thu, 18 February 2016, 00:37:54
Post by: filphil on Thu, 18 February 2016, 04:04:31
Just finished installing sip sockets and switches onto the PCB. Soldering still needs to be done. I also put keys in to get a feel of the board and my 67g Zealios. Really delightful. Zealios are wicked and the board is an awsome typing experience! Although I still need to perform soldering I sat down to get used to the 02D software. Must admit I am rather confused. This is my first custom and I have not programmed any boards previously. May I ask the noob question what you guys use your layers for? Also, anyone interested in sharing configs? Would be awsome to have a Duck custom keyboard hex database on i.e. GitHub.
I really don't use the layer function. Admittedly I don't think I have a use for it but I kept function layer 4 from from default for the rgb control.
Post by: omgar on Thu, 18 February 2016, 08:23:18
Just finished installing sip sockets and switches onto the PCB. Soldering still needs to be done. I also put keys in to get a feel of the board and my 67g Zealios. Really delightful. Zealios are wicked and the board is an awsome typing experience! Although I still need to perform soldering I sat down to get used to the 02D software. Must admit I am rather confused. This is my first custom and I have not programmed any boards previously. May I ask the noob question what you guys use your layers for? Also, anyone interested in sharing configs? Would be awsome to have a Duck custom keyboard hex database on i.e. GitHub.
On my Orion I have Control mapped to Caps Lock and Layer 2 mapped to L Ctrl. In layer 2 I have media controls on Z (Prev), X (Pause), C (Next), V (Vol Down), B (Vol Up). That's it for right now. I'm still waiting on some LED's so I haven't played too much with any of the LED controls.
Post by: romevi on Thu, 18 February 2016, 09:58:37
Just finished installing sip sockets and switches onto the PCB. Soldering still needs to be done. I also put keys in to get a feel of the board and my 67g Zealios. Really delightful. Zealios are wicked and the board is an awsome typing experience! Although I still need to perform soldering I sat down to get used to the 02D software. Must admit I am rather confused. This is my first custom and I have not programmed any boards previously. May I ask the noob question what you guys use your layers for? Also, anyone interested in sharing configs? Would be awsome to have a Duck custom keyboard hex database on i.e. GitHub.
I really don't use the layer function. Admittedly I don't think I have a use for it but I kept function layer 4 from from default for the rgb control.
I use my function layer all the time, but that's on my 60%. As for my TKL, the only time I use it is for controlling the LEDs and accessing the numpad a la Realforce.
Post by: filphil on Thu, 18 February 2016, 18:33:13
Just finished installing sip sockets and switches onto the PCB. Soldering still needs to be done. I also put keys in to get a feel of the board and my 67g Zealios. Really delightful. Zealios are wicked and the board is an awsome typing experience! Although I still need to perform soldering I sat down to get used to the 02D software. Must admit I am rather confused. This is my first custom and I have not programmed any boards previously. May I ask the noob question what you guys use your layers for? Also, anyone interested in sharing configs? Would be awsome to have a Duck custom keyboard hex database on i.e. GitHub.
I really don't use the layer function. Admittedly I don't think I have a use for it but I kept function layer 4 from from default for the rgb control.
I use my function layer all the time, but that's on my 60%. As for my TKL, the only time I use it is for controlling the LEDs and accessing the numpad a la Realforce.
I guess i could do something similar since a numpad can be pretty useful. Really i just want to use the 5 leds in the home cluster. I dislike underutilized features on my boards.
Post by: 64rky on Fri, 19 February 2016, 20:41:13
Post by: filphil on Fri, 19 February 2016, 21:03:04
Is it possible to be too in love with a keyboard?
Depends... Did you put your manhood in it?
Post by: 64rky on Fri, 19 February 2016, 21:20:33
Is it possible to be too in love with a keyboard?
Depends... Did you put your manhood in it?
Well, things got a bit weird... Oh god the feels again... :-[
Post by: filphil on Fri, 19 February 2016, 21:21:45
Is it possible to be too in love with a keyboard?
Depends... Did you put your manhood in it?
Well, things got a bit weird... Oh god the feels again... :-[
My board is going in to surgery. She'll come back stronger.
Post by: romevi on Fri, 19 February 2016, 21:31:59
Post by: Geekmie on Fri, 19 February 2016, 21:58:41
Post by: Steezus on Fri, 19 February 2016, 22:00:45
This looks awesome! But the question is how I can get one... any group buy soon?
The group buy purchase period ended around 9-10 months ago. There will be another revision in a year or so but not anytime soon.
Post by: E3E on Fri, 19 February 2016, 22:10:52
Is it possible to be too in love with a keyboard?
Depends... Did you put your manhood in it?
Well, things got a bit weird... Oh god the feels again... :-[
My board is going in to surgery. She'll come back stronger.
Fiphil, don't you have three of these babies, or did you give the others away as gifts or something? What became of them? :O
Post by: Steezus on Fri, 19 February 2016, 22:11:20
Is it possible to be too in love with a keyboard?
Depends... Did you put your manhood in it?
Well, things got a bit weird... Oh god the feels again... :-[
My board is going in to surgery. She'll come back stronger.
Fiphil, don't you have three of these babies, or did you give the others away as gifts or something? What became of them? :O
Sold one to me and gave the other to his brother. He only has one for himself. :thumb:
Post by: filphil on Fri, 19 February 2016, 22:34:19
Post by: Geekmie on Fri, 19 February 2016, 23:24:38
One per year~I have to wait carefully I guessThis looks awesome! But the question is how I can get one... any group buy soon?
The group buy purchase period ended around 9-10 months ago. There will be another revision in a year or so but not anytime soon.
Post by: axtran on Fri, 19 February 2016, 23:59:57
Post by: E3E on Sat, 20 February 2016, 01:42:59
Too bad there's only 7 ALPS Orions. Because _those_ are the best!
The 7 Samurai :P
Post by: romevi on Sat, 20 February 2016, 02:01:40
Too bad there's only 7 ALPS Orions. Because _those_ are the best!
The 7 Samurai
Which four will fall? :(
Post by: whentheclouds on Sat, 20 February 2016, 06:00:22
Post by: E3E on Tue, 23 February 2016, 21:47:31
Post by: zzyjayfree on Fri, 26 February 2016, 23:18:51
So it's been asked a million times, but does anyone here have a flat acrylic bottom they wouldn't mind sparing? I'm thinking about making my own though!
I might have a spare one. Send me a pm
Post by: appleonama on Sat, 27 February 2016, 02:47:48
Post by: filphil on Sat, 27 February 2016, 03:19:05
Anyone have an extra plate or pcb? I'd love to buy it either. :D
Steel and pcb here
Post by: 64rky on Sat, 27 February 2016, 07:49:36
Anyone have an extra plate or pcb? I'd love to buy it either. :D
Steel and pcb here
If he doesn't take it, I'm interested.
Post by: rainb1ood on Sat, 27 February 2016, 08:02:54
Post by: Xiro7 on Sat, 27 February 2016, 09:49:18
Thanks all for any help
Post by: 64rky on Sat, 27 February 2016, 09:52:11
I just bought one of these sets and this will be my first custom keyboard build. I joined the Zelios switch group buy, but am unsure of what else I need to purchase for this keyboard. Is anyone able to give me a list of what parts I should buy and maybe a good tutorial of how to put this thing together? Is there any software I need to test/update the LED lighting/firmware/key layout with it?
Thanks all for any help
Steezus built mine a little while back (https://geekhack.org/index.php?topic=78605.0)...
You will need:
- 100 1.8mm LED's (you will have some left overs, remember there are 8 extra LED's for the indicators).
- Stabilizers
I think that's it...
Post by: Xiro7 on Sat, 27 February 2016, 10:12:45
I just bought one of these sets and this will be my first custom keyboard build. I joined the Zelios switch group buy, but am unsure of what else I need to purchase for this keyboard. Is anyone able to give me a list of what parts I should buy and maybe a good tutorial of how to put this thing together? Is there any software I need to test/update the LED lighting/firmware/key layout with it?
Thanks all for any help
Steezus built mine a little while back (https://geekhack.org/index.php?topic=78605.0)...
You will need:
- 100 1.8mm LED's (you will have some left overs, remember there are 8 extra LED's for the indicators).
- Stabilizers
I think that's it...
Thanks, I reached out to him for a buying list he will need. Did you require anything on your computers to adjust the lights/colors or change the keymap?
Post by: 64rky on Sat, 27 February 2016, 10:18:31
I just bought one of these sets and this will be my first custom keyboard build. I joined the Zelios switch group buy, but am unsure of what else I need to purchase for this keyboard. Is anyone able to give me a list of what parts I should buy and maybe a good tutorial of how to put this thing together? Is there any software I need to test/update the LED lighting/firmware/key layout with it?
Thanks all for any help
Steezus built mine a little while back (https://geekhack.org/index.php?topic=78605.0)...
You will need:
- 100 1.8mm LED's (you will have some left overs, remember there are 8 extra LED's for the indicators).
- Stabilizers
I think that's it...
Thanks, I reached out to him for a buying list he will need. Did you require anything on your computers to adjust the lights/colors or change the keymap?
From a hardware perspective, that's it... for software
You download the O2D software. Here are some instructions I made for myself for the Lightsaver, the Orion uses the same software:
https://geekhack.org/index.php?topic=40501.13515;wap2
https://geekhack.org/index.php?topic=51252.850
1. Change computer to Korea. Not the language but the PC itself. See sifo message.
1. Download the 02D Keymapper software
2. change your system locale to Korean (Control Panel -> Region and Language -> Administrative tab -> Language for non-Unicode Programs -> Change system locale). You need to do this so that you have arrow keys show in your software.
3. set everything up and save to a hex file, you will need to create a blank .hex file first, save it in the same folder wwhere your 02D program exe lives.
4. Now you want to program your board, so download and install ATMEL Flip
5. to put the Lightsaver into programmable mode, unplug the board, then press and hold the top right key to the backspace as you plug it back in.
5.a If you have not done this before, your PC will not recognize it, you should use the driver from the usb folder in the FLIP install location (eg: C:\Program Files (x86)\Atmel\Flip 3.4.7\usb), this will allow FLIP to recognize the programmable usb device (as you have now switched the board to programmable mode).
6. choose ATmega32U3 as the device.
7. Choose USB as the communication method.
8. Load the hex file.
8. Run.
Post by: appleonama on Sat, 27 February 2016, 16:41:01
http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docx
Post by: kacase on Sat, 27 February 2016, 17:50:33
While desoldering the ' switch's sip socket (had to replace the whole switch because it was sticky), I pulled part of the pcbs socket for the sip socket out as well. After installing a brand new switch with sip sockets and soldering it, I noticed that none of the LEDs in the third row, left and including the ' key, were lit up. Also the three left bottom SMD RGB LEDs were malfunctioning. One glimmering and vigorously switching to random colours, the others not lighting up at all. So I guess I have broken half of my orion. Unless you guys have any recommendations on how to fix it.
The typing itself works fine. Its just the lighting that is broken.
Otherwise I would like to maybe get a pcb from someone here who has a spare. I would be really happy to hear from someone!
Post by: appleonama on Sat, 27 February 2016, 17:59:54
I think I have fried half of my orion :'(
While desoldering the ' switch's sip socket (had to replace the whole switch because it was sticky), I pulled part of the pcbs socket for the sip socket out as well. After installing a brand new switch with sip sockets and soldering it, I noticed that none of the LEDs in the third row, left and including the ' key, were lit up. Also the three left bottom SMD RGB LEDs were malfunctioning. One glimmering and vigorously switching to random colours, the others not lighting up at all. So I guess I have broken half of my orion. Unless you guys have any recommendations on how to fix it.
The typing itself works fine. Its just the lighting that is broken.
Otherwise I would like to maybe get a pcb from someone here who has a spare. I would be really happy to hear from someone!
I ruined my board as well which is why I asked for a pcb and plate :-\
edit: actually I ruined it quite a while back I've just been too embarrassed to mention it :p :p :p
anyways you are having the same problems as everyone who has encountered this issue with flashing rgb leds. It is a design flaw in the pcb. Here is the fix for the rgb led's. I am not sure what is wrong with your led's not turning on. If you can take a photo I can help you
(http://i.imgur.com/ztMk8kh.jpg)
The issue comes from the (+) copper hole on the led. This specific hole is easily prone to damage when desoldered and it stops the flow of current. To repair this issue you need to solder a small wire from the capacitor to the (+) pad, this should fix your issue. The led's not turning on might be the result of another damaged pad. Please take a photo and i can probably lead you to a fix.
special thanks to 02d who gave me this info
Post by: filphil on Sun, 28 February 2016, 07:14:42
the pcb and plate went to apple for gb cost plus shipping and fees. If I come across any more I'll be sure to let you all know.
Post by: rainb1ood on Sun, 28 February 2016, 07:42:31
Post by: filphil on Sun, 28 February 2016, 08:07:05
Post by: rainb1ood on Sun, 28 February 2016, 08:12:08
Sorry if my post came out as whiny or negative.
Post by: kacase on Sun, 28 February 2016, 08:44:15
And thanks for the tip apple! I will upload a picture on Wednesday when I'm home rom my work trip!
Post by: E3E on Sun, 28 February 2016, 08:45:59
Lucky apple. Im a bit salty I didnt get to buy it even though you said back on Feb 2 you'll let me know via PM if you'll decide to sell it
Rainblood, I gotcha bro. The Orion v2 I have coming in will have an alu and stainless plate, but I plan on just using the Alps and not the MX at all, so the steel is yours, my friend. :)
Post by: Vittra on Sun, 28 February 2016, 09:01:36
;)
Post by: appleonama on Sun, 28 February 2016, 09:08:53
v3 somedaysomeday next year :confused:
;)
octagon, viper, trinity, keypad too many ducks
Post by: rainb1ood on Sun, 28 February 2016, 09:18:22
That is awesome E3E!Lucky apple. Im a bit salty I didnt get to buy it even though you said back on Feb 2 you'll let me know via PM if you'll decide to sell it
Rainblood, I gotcha bro. The Orion v2 I have coming in will have an alu and stainless plate, but I plan on just using the Alps and not the MX at all, so the steel is yours, my friend. :)
PM sent
Post by: filphil on Sun, 28 February 2016, 09:28:12
I didn't think anything negative with your post bud. It was just uncharacteristic of me to forget about that whole exchange and am glad it worked itself out in the end.
Post by: rainb1ood on Sun, 28 February 2016, 09:44:25
Post by: Frizer on Sun, 28 February 2016, 10:22:43
Got the blues :-*
Post by: 64rky on Sun, 28 February 2016, 12:02:18
Show Image(http://i.imgur.com/KfgE10I.jpg)
Got the blues :-*
Oh, I like this setup!
Post by: radio_killah on Sun, 28 February 2016, 13:33:02
Show Image(http://i.imgur.com/KfgE10I.jpg)
Got the blues :-*
Looks like space cadet. :thumb:
Post by: appleonama on Sun, 28 February 2016, 19:08:12
Post by: 64rky on Sun, 28 February 2016, 20:50:48
Please pm me if you are interested in trading your winkeyless bluegray top for a winkey bluegray top :D
Edit: That was blank....
I might do if the PCB came with it, I unfortunately already have my switches soldered... well not unfortunately, I love it, but you know what I mean.
Post by: CPTBadAss on Sun, 28 February 2016, 21:19:15
Post by: appleonama on Sun, 28 February 2016, 21:23:19
Please pm me if you are interested in trading your winkeyless bluegray top for a winkey bluegray top :D
Edit: That was blank....
I might do if the PCB came with it, I unfortunately already have my switches soldered... well not unfortunately, I love it, but you know what I mean.
What?
Post by: Steezus on Sun, 28 February 2016, 21:28:28
Please pm me if you are interested in trading your winkeyless bluegray top for a winkey bluegray top :D
Edit: That was blank....
I might do if the PCB came with it, I unfortunately already have my switches soldered... well not unfortunately, I love it, but you know what I mean.
What?
I built him his Orion so he does not have the proper tools to desolder the switches and make it winkeyless.
Post by: appleonama on Sun, 28 February 2016, 22:35:37
Post by: ctrlX on Mon, 29 February 2016, 11:06:06
Post by: riotonthebay on Mon, 29 February 2016, 11:07:12
Speaking of ruining PCBs... I believe I messed up also. I had to desolder a switch and it was a real m****r f****r to get out. After soldering a new switch in, it does not register key presses. LED on that switch works though. Could I have damaged something due to over heating during the desolder process? Is it the resistor or diode maybe? I am by no means any electronics expert and this is my first custom board. So I apologize for not knowing what is what on the PCB. Any help would be greatly appreciated. Cheers!
Do you have the ability to take a macro shot of the soldering done for the switch in question?
Post by: ctrlX on Mon, 29 February 2016, 11:44:53
Post by: R1N3 on Mon, 29 February 2016, 11:47:38
Had a blast building one of these with R1N3 today. Can't wait for his picsKeyboard in question:
(http://images.tapatalk-cdn.com/16/02/29/345e69956749bd7848b00308046b2276.jpg)
(http://images.tapatalk-cdn.com/16/02/29/0384f71485535858b64bcc0d1d992b53.jpg)
Post by: Steezus on Mon, 29 February 2016, 12:05:51
Had a blast building one of these with R1N3 today. Can't wait for his picsKeyboard in question:Show Image(http://images.tapatalk-cdn.com/16/02/29/345e69956749bd7848b00308046b2276.jpg)Show Image(http://images.tapatalk-cdn.com/16/02/29/0384f71485535858b64bcc0d1d992b53.jpg)
Linears with an acrylic plate, now that's interesting. How are you liking it? Nice build though. :thumb:
Post by: ctrlX on Mon, 29 February 2016, 15:12:20
Speaking of ruining PCBs... I believe I messed up also. I had to desolder a switch and it was a real m****r f****r to get out. After soldering a new switch in, it does not register key presses. LED on that switch works though. Could I have damaged something due to over heating during the desolder process? Is it the resistor or diode maybe? I am by no means any electronics expert and this is my first custom board. So I apologize for not knowing what is what on the PCB. Any help would be greatly appreciated. Cheers!
Do you have the ability to take a macro shot of the soldering done for the switch in question?
Here are two close-up shots of the switch. Taken with a Nikon 24-70 mm f/2.8 FX lens. All the residue makes it look awful... I have not done any cleaning yet. Shots are taken after I de-soldered the switch and soldered another switch in place. Right after that I ran the board through a switch tester and noticed it did not respond to key strokes. Then I wicked away some solder and re-applied some new solder in hope of solving the problem. Please note that the LED for that switch is not soldered, but I know it works after closing the circuit.
[attachimg=1 width=400]
Soldering on the right is really bad. I really should redo that one (if not both).
[attachimg=2 width=400]
Same switch but photographed from the other side.
So what do you guys reckon? Does the pictures show any obvious problems or am I looking at not having a functioning F9 key on my Orion V2? Any help and/or suggestions are of course greatly appreciated.
Post by: Steezus on Mon, 29 February 2016, 17:10:01
Post by: R1N3 on Tue, 01 March 2016, 18:09:35
Tbh, from someone who slams 1,2,3,4,5,Q,W,E,R,T,A,S,D,F,G,Z,X,C,V and SPACE at least 8 hours a day, it's the dreamHad a blast building one of these with R1N3 today. Can't wait for his picsKeyboard in question:Show Image(http://images.tapatalk-cdn.com/16/02/29/345e69956749bd7848b00308046b2276.jpg)Show Image(http://images.tapatalk-cdn.com/16/02/29/0384f71485535858b64bcc0d1d992b53.jpg)
Linears with an acrylic plate, now that's interesting. How are you liking it? Nice build though. :thumb:
Post by: appleonama on Tue, 01 March 2016, 18:12:24
You'll need to grab a multimeter and check your traces. You'll want to have the multimeter set on the continuity setting(sideways looking Wifi symbol), it should beep when you touch the two prongs together. You'll want to check right pin to diode and left pin to a neighboring switch's left pin. The neighboring switch needs to be along the the same traces, I can't tell from that picture but it may be on the left and right or up and down. You can even check other switches to see how the traces find out what where to get a beep from the continuity check.adding to this. I'm assuming you are using zealios switches so maybe you have installed a bad switch. I heard they have chattering issues but I am not sure chattering stop switch registration. you should read about it more on the zealio group buy thread
Post by: Steezus on Tue, 01 March 2016, 18:30:22
You'll need to grab a multimeter and check your traces. You'll want to have the multimeter set on the continuity setting(sideways looking Wifi symbol), it should beep when you touch the two prongs together. You'll want to check right pin to diode and left pin to a neighboring switch's left pin. The neighboring switch needs to be along the the same traces, I can't tell from that picture but it may be on the left and right or up and down. You can even check other switches to see how the traces find out what where to get a beep from the continuity check.adding to this. I'm assuming you are using zealios switches so maybe you have installed a bad switch. I heard they have chattering issues but I am not sure chattering stop switch registration. you should read about it more on the zealio group buy thread
Chattering is basically early activation of the switch. Just by tapping the stem and not even compressing the spring will activate the switch if it chatters. The chattering issues were caused when one would apply heat for too long on a pin of the switch and melt the plastic housing which would slightly shift the leaf contact.
Post by: ctrlX on Wed, 02 March 2016, 04:39:13
Just finished installing sip sockets and switches onto the PCB. Soldering still needs to be done. I also put keys in to get a feel of the board and my 67g Zealios. Really delightful. Zealios are wicked and the board is an awsome typing experience! Although I still need to perform soldering I sat down to get used to the 02D software. Must admit I am rather confused. This is my first custom and I have not programmed any boards previously. May I ask the noob question what you guys use your layers for? Also, anyone interested in sharing configs? Would be awsome to have a Duck custom keyboard hex database on i.e. GitHub.
I really don't use the layer function. Admittedly I don't think I have a use for it but I kept function layer 4 from from default for the rgb control.
I use my function layer all the time, but that's on my 60%. As for my TKL, the only time I use it is for controlling the LEDs and accessing the numpad a la Realforce.
Switches are soldered and started playing around with the O2D KeyMapper. Had to backtrack a couple of posts and gathered enough information to grasp the concept of editing the layout using the software. So cheers for that! :)
So far I am only interested in controlling LEDs. Need to do some more testing tonight to make sure I am satisfied with my mapping. Pre-defined layouts are really good out of the box, so no need to alter the layout that much.
Post by: ctrlX on Wed, 02 March 2016, 05:04:01
You'll need to grab a multimeter and check your traces. You'll want to have the multimeter set on the continuity setting(sideways looking Wifi symbol), it should beep when you touch the two prongs together. You'll want to check right pin to diode and left pin to a neighboring switch's left pin. The neighboring switch needs to be along the the same traces, I can't tell from that picture but it may be on the left and right or up and down. You can even check other switches to see how the traces find out what where to get a beep from the continuity check.
Went out yesterday and bought myself a multimeter. I must admit I didn't manage to find the source of the faulty switch. Actually it is not the switch that is the problem. I've tested with 3 different Zealio switches and the end result is the same. I must have screwed up something during the first de-soldering. Probably applied heat for too long. At first I thought I burned the diode connected to the switch. I tested it with my multimeter (set to diode-mode) and the multimeter displayed a current of roughly 0.5.
I then switched to continuity-mode and tried troubleshooting according to your instructions. The faulty switch is F9, so imagine having the keyboard infront of you facing you in the correct typing position. Then just flip the board so the back-side of the PCB is facing you. Here's the weird part...
I put one prong against the left switch pin and the other prong against the right side of the diode. While holding the prongs in this position I pressed the switch key and received a beep from the multimeter (see blue markings on image below). Doesn't that mean I've closed the circuit and the PCB should register a key press?
[attach=1 width=400]
I must underline I am completely new to electronics and last time I held a multimeter in my hand was in high school when learning about the basic components, i.e. resistors, diodes etc.
EDIT:
I have spotted a potential cause of the problem. At closer inspection of the soldered right switch pin, a piece of the through hole pad on the PCB has fallen of or been ripped away. See the cyan marking in the image below. Could this be the explanation for having a non-working F9 key?
[attach=2 width=400]
Post by: appleonama on Sat, 05 March 2016, 21:51:29
opinion on these for the orion :D
Post by: omgar on Sun, 06 March 2016, 22:07:12
http://shop.taobaofocus.com/item.php?id=16411660020
opinion on these for the orion :D
Can't go wrong with some Classic Beige, IMO.
(http://i.imgur.com/llbleIL.jpg)
Post by: appleonama on Sun, 06 March 2016, 22:07:57
http://shop.taobaofocus.com/item.php?id=16411660020
opinion on these for the orion :D
Can't go wrong with some Classic Beige, IMO.Show Image(http://i.imgur.com/llbleIL.jpg)
you're right I bought anyways :D
Post by: appleonama on Sun, 06 March 2016, 22:16:15
winkey has lost my interest
Post by: E3E on Mon, 07 March 2016, 00:07:32
Post by: axtran on Mon, 07 March 2016, 15:34:04
Winkey looks nice too! It seems that there was a 50/50 split between people who ordered winkey and winkeyless on the order forms too. They're both good!
I dunno... 84-key is best... ;)
Post by: E3E on Mon, 07 March 2016, 17:38:39
Winkey looks nice too! It seems that there was a 50/50 split between people who ordered winkey and winkeyless on the order forms too. They're both good!
I dunno... 84-key is best... ;)
Axy, don't you start raining on my 86 key parade! :mad:
I do have duck blockers, but if I wanted to use them for Alps, I'd have to shave down the bottom that's supposed to go through the MX switch stem well cut-outs.
Winkey was actually less common for the Alps boards, but 50/50 split overall.
That said, if anyone with a black winkeyless layout is yearning for some winkeys, well... If you REALLY want a winkey top, I suppose I could trade mine. ;)
Post by: rainb1ood on Mon, 07 March 2016, 18:25:38
Post by: appleonama on Mon, 07 March 2016, 18:26:32
How does one acquire/purchase one of them duck blockers?
this
Post by: missalaire on Tue, 08 March 2016, 16:32:15
Post by: appleonama on Thu, 10 March 2016, 00:59:06
first set up
-Fresh PCB from duck0013
-plastic plate from filphil
-65g krytox relubed zealios
-GMK hyperfuse
-420 Noct clack
(http://i.imgur.com/aYn4EPC.jpg)
Post by: laguar on Thu, 10 March 2016, 23:52:36
In fitting with the celestial theme I am calling this build "red shift". Reds with red o-rings (maybe ill drop these), to match the red top case and PCB. Currently using Cherry98s from PBT4.
[attachimg=1]
[attachimg=2]
[attachimg=3]
[attachimg=4]
Post by: appleonama on Thu, 10 March 2016, 23:58:47
MoreWell, it took a lot longer than I hoped, but here it is.
In fitting with the celestial theme I am calling this build "red shift". Reds with red o-rings (maybe ill drop these), to match the red top case and PCB. Currently using Cherry98s from PBT4.
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
sweet man that looks great
you should've modded the switches with a heavier spring and clear tops :'(
Post by: E3E on Fri, 11 March 2016, 09:25:47
sweet man that looks great
you should've modded the switches with a heavier spring and clear tops :'(
Clear tops dyed red, you mean! Well, stock Gateron tops would probably hold the color better. :P
EDIT: In all honesty though, I like the contrast of black and red on the plate and what not. I think it coordinates well. IMO, clear switch tops look best with clear and black switches.
Post by: Geekmie on Fri, 11 March 2016, 10:36:23
Post by: FrostyToast on Fri, 11 March 2016, 10:48:58
I guess I should pop up now and then to ask for another round ;)
Orion V3 is already confirmed. Asking for a second round is a little unnecessary.
Post by: Geekmie on Fri, 11 March 2016, 10:50:10
Ask for V3 then, LOL. Is there any link for V3 design?I guess I should pop up now and then to ask for another round ;)
Orion V3 is already confirmed. Asking for a second round is a little unnecessary.
Post by: E3E on Fri, 11 March 2016, 10:55:36
I don't think he has drawn up anything for the Orion v3 so soon though.
Post by: Pemdas on Fri, 18 March 2016, 23:52:02
(http://i.imgur.com/8R14mOY.png)
For a 1.5x - 1x - 1.5x layout I would skip the diode that is not circled, correct?
(http://i.imgur.com/ctJMpcw.png)
Secondly I'm assuming the pads the arrows are pointing at are for the resistors for the notification LEDs. Which resistor am I supposed to use for them?
Also if I'm using switches with LEDs built in for the scroll/num/caps would I only bother with the top pads and forget the bottom pads?
(http://i.imgur.com/8BSZvbi.png)
And lastly do I have to worry about these at all?
I'm pretty sure I know the answers to most of these but I'm pretty nervous about working on it so I wanted to make sure.
Thanks in advance for any answers :thumb:
Post by: E3E on Sat, 19 March 2016, 00:25:45
About to start work on my alps pcb and got a couple things I want to verify before starting.Show Image(http://i.imgur.com/8R14mOY.png)
For a 1.5x - 1x - 1.5x layout I would skip the diode that is not circled, correct?Show Image(http://i.imgur.com/ctJMpcw.png)
Secondly I'm assuming the pads the arrows are pointing at are for the resistors for the notification LEDs. Which resistor am I supposed to use for them?
Also if I'm using switches with LEDs built in for the scroll/num/caps would I only bother with the top pads and forget the bottom pads?Show Image(http://i.imgur.com/8BSZvbi.png)
And lastly do I have to worry about these at all?
I'm pretty sure I know the answers to most of these but I'm pretty nervous about working on it so I wanted to make sure.
Thanks in advance for any answers :thumb:
I don't believe you need to worry about the LED indicators near scroll lock and such as they are not compatible with the Orion v2. Only need to focus on the in-switch LEDs. :)
I might be mistaken, but I think you need to put diodes on all positions as they are part of the circuit. I would add the diodes there regardless.
As for the resistor value, Alienman82 recommended resistors of this value (http://www.amazon.com/gp/product/B00W2B5ZH8?psc=1&redirect=true&ref_=oh_aui_detailpage_o00_s00) for the Orion v2 Alphas PCB, as that's what he heard from Leeku.
The bits in the last picture are nothing you need to worry about as far as I know. I'm pretty sure they are serial ports used for debugging and such. https://en.wikipedia.org/wiki/In-system_programming
Post by: Pemdas on Sat, 19 March 2016, 00:59:07
I don't believe you need to worry about the LED indicators near scroll lock and such as they are not compatible with the Orion v2. Only need to focus on the in-switch LEDs. :)
I might be mistaken, but I think you need to put diodes on all positions as they are part of the circuit. I would add the diodes there regardless.
As for the resistor value, Alienman82 recommended resistors of this value (http://www.amazon.com/gp/product/B00W2B5ZH8?psc=1&redirect=true&ref_=oh_aui_detailpage_o00_s00) for the Orion v2 Alphas PCB, as that's what he heard from Leeku.
The bits in the last picture are nothing you need to worry about as far as I know. I'm pretty sure they are serial ports used for debugging and such. https://en.wikipedia.org/wiki/In-system_programming
Awesome that clears everything up! Ordered the resistors, thanks so much for the info! :thumb:
Can't wait to get this all built up
Post by: appleonama on Thu, 24 March 2016, 19:27:09
I am finally rebuilding my orion but I can't decide what switches to use on what plate.
I am building two orion pcbs this time no **** ups like before.
1 aluminum
1 plastic
I have 65g tactile zealios and 62g ergo MX grey with clear switch tops.
I was thinking zeal on plastic and mx grey on aluminum to keep an even grey color tone for aesthetics. opinions?
(http://i.imgur.com/dXKtUME.jpg)
(http://i.imgur.com/joNUdhW.jpg)
Post by: E3E on Thu, 24 March 2016, 19:46:08
I need help guys! please!!
I am finally rebuilding my orion but I can't decide what switches to use on what plate.
I am building two orion pcbs this time no **** ups like before.
1 aluminum
1 plastic
I have 65g tactile zealios and 62g ergo MX grey with clear switch tops.
I was thinking zeal on plastic and mx grey on aluminum to keep an even grey color tone for aesthetics. opinions?Show Image(http://i.imgur.com/dXKtUME.jpg)Show Image(http://i.imgur.com/joNUdhW.jpg)
I think you're heading down the right path. Sometimes contrast is better, but sometimes having a more uniform color palette is pleasant too. Sounds like it'll be a bit greyscale. :P
Nice to see the plate has come in, by the way.
How did you mess up the PCB last time, man?
Post by: appleonama on Thu, 24 March 2016, 19:54:39
I think I am going to go down this path. Purple on plastic and Grey on aluminum.I need help guys! please!!
I am finally rebuilding my orion but I can't decide what switches to use on what plate.
I am building two orion pcbs this time no **** ups like before.
1 aluminum
1 plastic
I have 65g tactile zealios and 62g ergo MX grey with clear switch tops.
I was thinking zeal on plastic and mx grey on aluminum to keep an even grey color tone for aesthetics. opinions?Show Image(http://i.imgur.com/dXKtUME.jpg)Show Image(http://i.imgur.com/joNUdhW.jpg)
I think you're heading down the right path. Sometimes contrast is better, but sometimes having a more uniform color palette is pleasant too. Sounds like it'll be a bit greyscale. :P
Nice to see the plate has come in, by the way.
How did you mess up the PCB last time, man?
thanks so much man for the plate and pcb man <3 :-*
The aluminum plate is beautiful and much better looking than steel IMO
I thought I ruined my first pcb while desoldering. However the pads on the pcb are extremely sensitive and I managed to lift 1/6 of a millimeter of the pad. That is an extremely tiny amount of pad which caused half of the boards leds to stop working. About 3 weeks ago I managed to fix the issue with help from truecustoms on kbdlab.
It has been a constant struggle not being able to use my orion v2 :'( but today is the day.
(http://i.imgur.com/ztMk8kh.jpg)
Post by: E3E on Thu, 24 March 2016, 20:01:32
I think I am going to go down this path. Purple on plastic and Grey on aluminum.
thanks so much man for the plate and pcb man <3 :-*
The aluminum plate is beautiful and much better looking than steel IMO
I thought I ruined my first pcb by desoldering. However the pads on the pcb are extremely sensitive and I managed to lift 1/6 of a millimeter of the pad. That is an extremely tiny amount of pad which caused half of the boards leds to stop working. About 3 weeks ago I managed to fix the issue with help from truecustoms on kbdlab.
It's just a constant struggle not being able to use my orion v2 :'( but today is the day.Show Image(http://i.imgur.com/ztMk8kh.jpg)
Yeah, I agree with you! I wish Alps plates came in more than just steel, myself. The sandblasted anodized surface of aluminum is just really pretty. I love the look.
Yeah, Duck PCBs have TERRIBLE pads, man. I went through absolute hell with my Octagon when I desoldered it, though I must admit, it was my first time ever working with a board like that, so I made tons of mistakes, but somehow, I managed to repair the board to work 100% again. Troubleshooting sometimes helps, but sometimes you get caught at a seeming dead end where you can't trace the problem or a particular component is fried and there's no way you'd be able to figure it out unless you had more in-depth electrical knowledge.
I'm just a hobbyist that gets lucky, haha.
Good luck with the aluminum build. That's the one I'm looking forward to more. The plastic plate is just kinda meh. I've built two Orions with plastic plates, and while I find them a bit novel, I would prefer something more sturdy.
I have to say, I have handled carbon fiber for my Alps Eagle builds, but that aluminum plate for the Orion v2 was also surprisingly light too. :D
Post by: filphil on Thu, 24 March 2016, 20:14:29
Not saying you can't get through a pcb without messing up a trace. I found I had to relube my GH soldering pump because it was too heavily lubed in the first place. Too much lube caused some sticktion after some desoldering. After cleaning and light lubing of the soldering pump I got through without a hitch.
Post by: lootbag on Thu, 24 March 2016, 20:31:32
Planning to give my Duck Viper a big overhaul and using my Aoyue desoldering gun on all the switches and LEDs.
I did test the desoldering unit on a couple LEDs on the Duck PCB with no problems.
It would take me forever if I used the old wick or a manual pump.
Post by: appleonama on Thu, 24 March 2016, 20:43:22
Yeah I noticed that I found it easier to desolder duck's pcbs with a manual soldering pump. When I used my hakko desoldering iron on a lightsaver pcb it tore it a new one and that was with lowish heat setting and extra rosin for some help.
Not saying you can't get through a pcb without messing up a trace. I found I had to relube my GH soldering pump because it was too heavily lubed in the first place. Too much lube caused some sticktion after some desoldering. After cleaning and light lubing of the soldering pump I got through without a hitch.
I bought a desoldering station to work on my orion pcb but it was only sucking 3/4th's of the solder. It was disappointing that a 400 dollar machine couldn't do the work and I ended up returning it. Then I had to buy a manual pump the "ss-02" and that worked flawlessly but I needed the patience of a god. My desoldering was nearly flawless when I finished and I was so shocked that I somehow managed to f it up when I saw the dead smd led's
anyways thanks for the plastic plate fil :-*
Post by: E3E on Thu, 24 March 2016, 21:19:45
Yeah I noticed that I found it easier to desolder duck's pcbs with a manual soldering pump. When I used my hakko desoldering iron on a lightsaver pcb it tore it a new one and that was with lowish heat setting and extra rosin for some help.
Not saying you can't get through a pcb without messing up a trace. I found I had to relube my GH soldering pump because it was too heavily lubed in the first place. Too much lube caused some sticktion after some desoldering. After cleaning and light lubing of the soldering pump I got through without a hitch.
I was a bit of a novice then, only having worked on my multi-layer PCB Rapoo KX boards that were my introduction to the hobby, and really, because they were PITA multilayer PCBs, I bought a desoldering iron just for them, as I was doing switch swaps on them, and that included LEDs and all that fun stuff. Yeah, I guess I've always been passionate.
That said, again, I was a novice with the Octagon, but when I took the iron to the Duck Eagle PCB that was given to me by Deci for my hotswappable Alps project, I desoldered all of his switches using the desoldering iron with not a single lifted pad. There is certainly a technique to it, but I have to say, it's one of those things you feel more out of your intuition through experience than anything that can be described through words.
But do be careful, because these pads do curl up in the fetal position if too much heat gets to them.
I plan on taking a drill to my Leeku Alphas PCB (for the Orion v2) like I have with my hotswappable Alps Eagles. Hope nothing goes wrong. :P
Oh right, and like filphil expressed: flux is your friend. It makes for a lot more hassle-free and efficient soldering. Some people also swear by using lead alloy solder, but I prefer being a wimp and sticking with ROHS lead-free stuff. The lead-free stuff is always rosin core as well, but that's not enough sometimes. I hear lead solder works really well, but I just don't want to deal with that stuff. :eek:
Post by: lootbag on Thu, 24 March 2016, 22:29:51
Yeah I noticed that I found it easier to desolder duck's pcbs with a manual soldering pump. When I used my hakko desoldering iron on a lightsaver pcb it tore it a new one and that was with lowish heat setting and extra rosin for some help.
Not saying you can't get through a pcb without messing up a trace. I found I had to relube my GH soldering pump because it was too heavily lubed in the first place. Too much lube caused some sticktion after some desoldering. After cleaning and light lubing of the soldering pump I got through without a hitch.
I was a bit of a novice then, only having worked on my multi-layer PCB Rapoo KX boards that were my introduction to the hobby, and really, because they were PITA multilayer PCBs, I bought a desoldering iron just for them, as I was doing switch swaps on them, and that included LEDs and all that fun stuff. Yeah, I guess I've always been passionate.
That said, again, I was a novice with the Octagon, but when I took the iron to the Duck Eagle PCB that was given to me by Deci for my hotswappable Alps project, I desoldered all of his switches using the desoldering iron with not a single lifted pad. There is certainly a technique to it, but I have to say, it's one of those things you feel more out of your intuition through experience than anything that can be described through words.
But do be careful, because these pads do curl up in the fetal position if too much heat gets to them.
I plan on taking a drill to my Leeku Alphas PCB (for the Orion v2) like I have with my hotswappable Alps Eagles. Hope nothing goes wrong. :P
Oh right, and like filphil expressed: flux is your friend. It makes for a lot more hassle-free and efficient soldering. Some people also swear by using lead alloy solder, but I prefer being a wimp and sticking with ROHS lead-free stuff. The lead-free stuff is always rosin core as well, but that's not enough sometimes. I hear lead solder works really well, but I just don't want to deal with that stuff. :eek:
I guess it really is a "feel" thing and can vary from person to person (equipment to equipment)
Jumped right in after a plethora of YouTube videos.
But it was still nerve wracking doing my first desoldering job on an expensive Duck Viper.
Swapped in the smallest tip, set the temp to 350, made contact (gun to LED), felt the solder melt after literally a second, pulled the trigger.
Had to use small needle nose pliers to pull the LEDs out with a bit of force, not too much.
Did not even use flux or add any solder to the existing joints.
Everything went smoothly, hopefully because of the very little contact time between gun and pads.
Post by: appleonama on Thu, 24 March 2016, 23:17:12
hmm I am not sure how I feel about it. It feels flimsy and cheap .... especially with these jt keycaps. Only if I had my hyperfuse set......! ctrl alt excuses :blank:
I am sad now I was expecting a better feel maybe it is the caps.
Well now I wait for my shipment of mx greys and I will mod them with 62g gold spring and gateron clear tops.
Post by: yicaoyimu on Thu, 24 March 2016, 23:55:02
just finished the orion with plastic plate
hmm I am not sure how I feel about it. It feels flimsy and cheap .... especially with these jt keycaps. Only if I had my hyperfuse set......! ctrl alt excuses :blank:
I am sad now I was expecting a better feel maybe it is the caps.
Well now I wait for my shipment of mx greys and I will mod them with 62g gold spring and gateron clear tops.
Plastic plate gives me the worst typing experience I ever had.
(http://i.imgur.com/sJqg5Fn.jpg)
Grey switches on aluminum (steel) plate is exactly what I did with Orion v1 BTW.
(http://i.imgur.com/G5UgOZ0.jpg)
Post by: appleonama on Fri, 25 March 2016, 11:58:00
Morejust finished the orion with plastic plate
hmm I am not sure how I feel about it. It feels flimsy and cheap .... especially with these jt keycaps. Only if I had my hyperfuse set......! ctrl alt excuses :blank:
I am sad now I was expecting a better feel maybe it is the caps.
Well now I wait for my shipment of mx greys and I will mod them with 62g gold spring and gateron clear tops.
Plastic plate gives me the worst typing experience I ever had.Show Image(http://i.imgur.com/sJqg5Fn.jpg)
Grey switches on aluminum (steel) plate is exactly what I did with Orion v1 BTW.Show Image(http://i.imgur.com/G5UgOZ0.jpg)
Typing on the plastic plate is slowy growing on me. The major issue with the mushy feel at first was the led's. They kept clashing with the jtk keycaps which are a bit thicker than the GMK keycaps. Once I removed the led's typing on the board feels so much more natural. It definitely does feel like typing on pcb mounted switches I feel the pronounced tactility. It is a much more interesting feeling than typing steel. I think I really like it now lol
Post by: rainb1ood on Fri, 25 March 2016, 12:01:14
And yes same with me, it feels like typing on a PCB mounted board
Post by: appleonama on Fri, 25 March 2016, 12:03:26
I didn't like the plastic plate as well, its like it makes the wobble on zealios more pronounced lol
what do you mean wobble?
Post by: appleonama on Fri, 25 March 2016, 12:05:15
love the clear bottom :-*
Post by: rainb1ood on Fri, 25 March 2016, 12:06:45
I didn't like the plastic plate as well, its like it makes the wobble on zealios more pronounced lol
what do you mean wobble?
Post by: appleonama on Fri, 25 March 2016, 12:09:26
When you move the keys as if its a trackpoint, it wobbles a lot vs Cherry switches.I didn't like the plastic plate as well, its like it makes the wobble on zealios more pronounced lol
what do you mean wobble?
ehh I just checked it is only a tiny bit compare to my board with mx clears
Post by: appleonama on Fri, 25 March 2016, 13:12:50
its official the plastic plate grew on me I am in love now :p
Post by: filphil on Fri, 25 March 2016, 15:09:35
Show Image(http://i.imgur.com/0QvsvZE.jpg)
its official the plastic plate grew on me I am in love now :p
Glad you ended up liking the plastic.
When I was actively testing I thought this:
can anyone explain the difference in feel between the 3 plates? Does the acrylic plate have less of a 'ping'?
If you're familiar with pcb mount or gons polycarbonate plate I would say it reminds me of those. Probably closer to the former actually. I opted for plastic over aluminum and steel for my board.
After typing on plastic for a while I thought I'd give the aluminum a longer test run and I still miss the gentle feel plastic gives over the metal plates. I WILL COME BACK TO THE PLASTIC WHEN MY ZEALIOS COME IN.
Post by: ctrlX on Sun, 27 March 2016, 08:07:31
While desoldering my F9 key I managed to break a trace which really bummed me out... :( Fortunately I was able to ghetto-wire it and now it is completely functional. As a first time build and first time solder I should have gone with Cherry switches. R1 Zealios were really troublesome. About 15 switches were chattering. Some so bad it was not good for typing at all. In the process of replacing them the PCB suffered some minor superficial scratches and dents. They are hard to spot with the naked eye, but knowing they are there kinda irritates me being a perfectionist. Fortunately the PCB is hidden and they kind of only exists in my mind. I do have to admit that the problems with Zealio switches really is a result of soldering inexperience as I did know of the low melting temperature of the switch housing. Next board will be Cherry MX, just to avoid having to desolder so many switches again.
Initially I wanted to put my Retro SA set on the Orion, but found the keys to wobble way to much. Another result of using Zealio switches. It is a matter of taste as other community members have no problems with Zealios + SA keycaps. Due to this I had to divert from my initial design and installed my Granite set. The key-wobbling is now gone and the typing experience much more pleasant.
The setup is not completely finished. I am still waiting on a custom USB-cable and some other colored LEDs to spice things up. One last issue I have is the mushy space bar as others have reported. I really hope that issue will just resolve by itself as can't be bothered with more deslodering and assembly. If anyone has any suggestions on improving the feel of the space bar without desoldering, please do let me know. :)
I apologize if this post sounds complaining/ranting, not my intention. Just want to share my personal experience. Putting that aside I have to say the board is awsome! It is built like a tank, has tons of features and looks hella good. I am so glad I also ordered the angled acrylic bottom. Since I ended soldering it myself, I really should have ordered an extra PCB.
[attach=1]
[attach=2]
[attach=3]
[attach=4]
Any comments and suggestions are as always greatly appreciated. Cheers!
Post by: ramnes on Sun, 27 March 2016, 11:36:38
My first Korean custom board. Actually my first build ever. I would be lying if I said it was easy. Although I must say that this board was perfect for a first build. Expensive, but still a good learning experience. Initially a community member was going to build it for me as I was too much of a **** doing it myself, but he went MIA. So I ended up doing it myself. Took me several weeks due to work, family commitments, buying tools etc.
While desoldering my F9 key I managed to break a trace which really bummed me out... :( Fortunately I was able to ghetto-wire it and now it is completely functional. As a first time build and first time solder I should have gone with Cherry switches. R1 Zealios were really troublesome. About 15 switches were chattering. Some so bad it was not good for typing at all. In the process of replacing them the PCB suffered some minor superficial scratches and dents. They are hard to spot with the naked eye, but knowing they are there kinda irritates me being a perfectionist. Fortunately the PCB is hidden and they kind of only exists in my mind. I do have to admit that the problems with Zealio switches really is a result of soldering inexperience as I did know of the low melting temperature of the switch housing. Next board will be Cherry MX, just to avoid having to desolder so many switches again.
Initially I wanted to put my Retro SA set on the Orion, but found the keys to wobble way to much. Another result of using Zealio switches. It is a matter of taste as other community members have no problems with Zealios + SA keycaps. Due to this I had to divert from my initial design and installed my Granite set. The key-wobbling is now gone and the typing experience much more pleasant.
The setup is not completely finished. I am still waiting on a custom USB-cable and some other colored LEDs to spice things up. One last issue I have is the mushy space bar as others have reported. I really hope that issue will just resolve by itself as can't be bothered with more deslodering and assembly. If anyone has any suggestions on improving the feel of the space bar without desoldering, please do let me know. :)
I apologize if this post sounds complaining/ranting, not my intention. Just want to share my personal experience. Putting that aside I have to say the board is awsome! It is built like a tank, has tons of features and looks hella good. I am so glad I also ordered the angled acrylic bottom. Since I ended soldering it myself, I really should have ordered an extra PCB.
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Any comments and suggestions are as always greatly appreciated. Cheers!
Congrats!
Post by: ika on Sun, 27 March 2016, 13:55:59
Show Image(http://i.imgur.com/0QvsvZE.jpg)
its official the plastic plate grew on me I am in love now :p
Glad you ended up liking the plastic.
When I was actively testing I thought this:can anyone explain the difference in feel between the 3 plates? Does the acrylic plate have less of a 'ping'?
If you're familiar with pcb mount or gons polycarbonate plate I would say it reminds me of those. Probably closer to the former actually. I opted for plastic over aluminum and steel for my board.
After typing on plastic for a while I thought I'd give the aluminum a longer test run and I still miss the gentle feel plastic gives over the metal plates. I WILL COME BACK TO THE PLASTIC WHEN MY ZEALIOS COME IN.
For what it's worth, I hated Zealios on acrylic. I'm typing on Zealios/alu plate now and it's a much more enjoyable experience. I do like the feel of scratchy cherry switches on acrylic, though. Maybe I'm just weird.
Post by: appleonama on Sun, 27 March 2016, 14:03:35
MoreMy first Korean custom board. Actually my first build ever. I would be lying if I said it was easy. Although I must say that this board was perfect for a first build. Expensive, but still a good learning experience. Initially a community member was going to build it for me as I was too much of a **** doing it myself, but he went MIA. So I ended up doing it myself. Took me several weeks due to work, family commitments, buying tools etc.
While desoldering my F9 key I managed to break a trace which really bummed me out... :( Fortunately I was able to ghetto-wire it and now it is completely functional. As a first time build and first time solder I should have gone with Cherry switches. R1 Zealios were really troublesome. About 15 switches were chattering. Some so bad it was not good for typing at all. In the process of replacing them the PCB suffered some minor superficial scratches and dents. They are hard to spot with the naked eye, but knowing they are there kinda irritates me being a perfectionist. Fortunately the PCB is hidden and they kind of only exists in my mind. I do have to admit that the problems with Zealio switches really is a result of soldering inexperience as I did know of the low melting temperature of the switch housing. Next board will be Cherry MX, just to avoid having to desolder so many switches again.
Initially I wanted to put my Retro SA set on the Orion, but found the keys to wobble way to much. Another result of using Zealio switches. It is a matter of taste as other community members have no problems with Zealios + SA keycaps. Due to this I had to divert from my initial design and installed my Granite set. The key-wobbling is now gone and the typing experience much more pleasant.
The setup is not completely finished. I am still waiting on a custom USB-cable and some other colored LEDs to spice things up. One last issue I have is the mushy space bar as others have reported. I really hope that issue will just resolve by itself as can't be bothered with more deslodering and assembly. If anyone has any suggestions on improving the feel of the space bar without desoldering, please do let me know. :)
I apologize if this post sounds complaining/ranting, not my intention. Just want to share my personal experience. Putting that aside I have to say the board is awsome! It is built like a tank, has tons of features and looks hella good. I am so glad I also ordered the angled acrylic bottom. Since I ended soldering it myself, I really should have ordered an extra PCB.
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Any comments and suggestions are as always greatly appreciated. Cheers!
nice board man! only issue is that iso layout :p
Post by: ctrlX on Sun, 27 March 2016, 14:13:47
MoreMy first Korean custom board. Actually my first build ever. I would be lying if I said it was easy. Although I must say that this board was perfect for a first build. Expensive, but still a good learning experience. Initially a community member was going to build it for me as I was too much of a **** doing it myself, but he went MIA. So I ended up doing it myself. Took me several weeks due to work, family commitments, buying tools etc.
While desoldering my F9 key I managed to break a trace which really bummed me out... :( Fortunately I was able to ghetto-wire it and now it is completely functional. As a first time build and first time solder I should have gone with Cherry switches. R1 Zealios were really troublesome. About 15 switches were chattering. Some so bad it was not good for typing at all. In the process of replacing them the PCB suffered some minor superficial scratches and dents. They are hard to spot with the naked eye, but knowing they are there kinda irritates me being a perfectionist. Fortunately the PCB is hidden and they kind of only exists in my mind. I do have to admit that the problems with Zealio switches really is a result of soldering inexperience as I did know of the low melting temperature of the switch housing. Next board will be Cherry MX, just to avoid having to desolder so many switches again.
Initially I wanted to put my Retro SA set on the Orion, but found the keys to wobble way to much. Another result of using Zealio switches. It is a matter of taste as other community members have no problems with Zealios + SA keycaps. Due to this I had to divert from my initial design and installed my Granite set. The key-wobbling is now gone and the typing experience much more pleasant.
The setup is not completely finished. I am still waiting on a custom USB-cable and some other colored LEDs to spice things up. One last issue I have is the mushy space bar as others have reported. I really hope that issue will just resolve by itself as can't be bothered with more deslodering and assembly. If anyone has any suggestions on improving the feel of the space bar without desoldering, please do let me know. :)
I apologize if this post sounds complaining/ranting, not my intention. Just want to share my personal experience. Putting that aside I have to say the board is awsome! It is built like a tank, has tons of features and looks hella good. I am so glad I also ordered the angled acrylic bottom. Since I ended soldering it myself, I really should have ordered an extra PCB.
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Any comments and suggestions are as always greatly appreciated. Cheers!
nice board man! only issue is that iso layout :p
Hehe, cheers! Being from EU I'm more used to ISO layout. I like ANSI also and got really used to it after 3 years of studying in Australia. I did however have a problem with two big-ass-shifts on ANSI. ^-^ I also find coding easier on that layout, but not for typing.
Post by: frostylove on Sun, 27 March 2016, 16:56:29
My first Korean custom board. Actually my first build ever. I would be lying if I said it was easy. Although I must say that this board was perfect for a first build. Expensive, but still a good learning experience. Initially a community member was going to build it for me as I was too much of a **** doing it myself, but he went MIA. So I ended up doing it myself. Took me several weeks due to work, family commitments, buying tools etc.
While desoldering my F9 key I managed to break a trace which really bummed me out... :( Fortunately I was able to ghetto-wire it and now it is completely functional. As a first time build and first time solder I should have gone with Cherry switches. R1 Zealios were really troublesome. About 15 switches were chattering. Some so bad it was not good for typing at all. In the process of replacing them the PCB suffered some minor superficial scratches and dents. They are hard to spot with the naked eye, but knowing they are there kinda irritates me being a perfectionist. Fortunately the PCB is hidden and they kind of only exists in my mind. I do have to admit that the problems with Zealio switches really is a result of soldering inexperience as I did know of the low melting temperature of the switch housing. Next board will be Cherry MX, just to avoid having to desolder so many switches again.
Initially I wanted to put my Retro SA set on the Orion, but found the keys to wobble way to much. Another result of using Zealio switches. It is a matter of taste as other community members have no problems with Zealios + SA keycaps. Due to this I had to divert from my initial design and installed my Granite set. The key-wobbling is now gone and the typing experience much more pleasant.
The setup is not completely finished. I am still waiting on a custom USB-cable and some other colored LEDs to spice things up. One last issue I have is the mushy space bar as others have reported. I really hope that issue will just resolve by itself as can't be bothered with more deslodering and assembly. If anyone has any suggestions on improving the feel of the space bar without desoldering, please do let me know. :)
I apologize if this post sounds complaining/ranting, not my intention. Just want to share my personal experience. Putting that aside I have to say the board is awsome! It is built like a tank, has tons of features and looks hella good. I am so glad I also ordered the angled acrylic bottom. Since I ended soldering it myself, I really should have ordered an extra PCB.
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Any comments and suggestions are as always greatly appreciated. Cheers!
This one REALLY rocks
Post by: E3E on Mon, 28 March 2016, 06:47:03
Oh right, I used Duplicolor Metalcast "Smoke" to darken the stainless steel plate:
(http://i.imgur.com/nQwK92z.jpg)
(http://i.imgur.com/AnMpR8og.jpg)
So here's the board:
(http://i.imgur.com/GuOjR9X.jpg)
(http://i.imgur.com/AC3hJ8d.jpg)
(http://i.imgur.com/iHUowkD.jpg)
My Orion v2 possesses the power of levitation!
(http://i.imgur.com/RoEI78c.jpg)
(http://i.imgur.com/UgOSrs7.jpg)
Here you can clearly see the holtite sockets used for the hotswap mod. I'm not sure how I feel about this bottom as it makes the board feel like nothing more than a top bezel with feet, lol.
(http://i.imgur.com/IarsCf3.jpg)
Stealthy in the background with my first Duck in the foreground. :3
I wanted the Alphas to be a lighter greyish black, and they technically are, but I think I left them in a wee bit too long. Now it looks like I just have a BoB stealth board, which is pretty cool. I have IBM 5140 caps I could use for a piano white and black look and SGI caps I could use if I want to redo the lighter keys in that grey color I was thinking of.
What do you guys thing? Good as is?
It's been one hell of a week. The hotswap mod and this build has drained the hell out of me. :confused:
Post by: bocahgundul on Mon, 28 March 2016, 06:58:16
Post by: E3E on Mon, 28 March 2016, 07:00:38
OMG E3E dat board is a beast omg. the only cons is that childish led :p
Thanks man, that definitely makes me happy to hear. :) This build has been soooo stressful, hahaha.
Yep, I think I'll either turn them off or make them a solid color or something. I haven't even programmed the firmware. I just wanted to finally finish this one, haha.
Post by: bocahgundul on Mon, 28 March 2016, 07:03:31
Solid white color! and its gonna be a dankest board everOMG E3E dat board is a beast omg. the only cons is that childish led :p
Thanks man, that definitely makes me happy to hear. :) This build has been soooo stressful, hahaha.
Yep, I think I'll either turn them off or make them a solid color or something. I haven't even programmed the firmware. I just wanted to finally finish this one, haha.
Post by: E3E on Mon, 28 March 2016, 07:11:00
Solid white color! and its gonna be a dankest board everOMG E3E dat board is a beast omg. the only cons is that childish led :p
Thanks man, that definitely makes me happy to hear. :) This build has been soooo stressful, hahaha.
Yep, I think I'll either turn them off or make them a solid color or something. I haven't even programmed the firmware. I just wanted to finally finish this one, haha.
Oh, white? Good idea! That wasn't even on my mind.
Post by: FLFisherman on Mon, 28 March 2016, 07:15:21
Hotswappable Alps Orion v2 with Alps SKCM Blue + SKCL Brown for Caps Lock and Scroll Lock with green LEDs. Dyed AT101 PBT caps. I tried dyeing two sample spacebars, but they warped easily and just came out an ugly brown, so I used Krylon Fusion on the space bar. Waiting for the paint to fully cure in a week before I mount it. I just set up up for these photos. :P
Oh right, I used Duplicolor Metalcast "Smoke" to darken the stainless steel plate:Show Image(http://i.imgur.com/nQwK92z.jpg)Show Image(http://i.imgur.com/AnMpR8og.jpg)
So here's the board:Show Image(http://i.imgur.com/GuOjR9X.jpg)Show Image(http://i.imgur.com/AC3hJ8d.jpg)Show Image(http://i.imgur.com/iHUowkD.jpg)
My Orion v2 possesses the power of levitation!Show Image(http://i.imgur.com/RoEI78c.jpg)Show Image(http://i.imgur.com/UgOSrs7.jpg)
Here you can clearly see the holtite sockets used for the hotswap mod. I'm not sure how I feel about this bottom as it makes the board feel like nothing more than a top bezel with feet, lol.Show Image(http://i.imgur.com/IarsCf3.jpg)
Stealthy in the background with my first Duck in the foreground. :3
I wanted the Alphas to be a lighter greyish black, and they technically are, but I think I left them in a wee bit too long. Now it looks like I just have a BoB stealth board, which is pretty cool. I have IBM 5140 caps I could use for a piano white and black look and SGI caps I could use if I want to redo the lighter keys in that grey color I was thinking of.
What do you guys thing? Good as is?
It's been one hell of a week. The hotswap mod and this build has drained the hell out of me. :confused:
It's said that you can always improve on what you have. However, I honestly don't see how here.
Post by: E3E on Mon, 28 March 2016, 07:20:37
It's said that you can always improve on what you have. However, I honestly don't see how here.
Thanks, FL. I think it's just a bit of all the frustration from the past weekend this took to build getting to me. Like, I was working on it from day into the early morning each day, so I'm really spent. I never thought I could get so stressed out from a keyboard build. :P
I need to work on the Lightpad next. Cool thing since it's black too, so it'll match perfectly. Then after that I think I'm taking a break, haha.
Post by: FLFisherman on Mon, 28 March 2016, 07:25:50
It's said that you can always improve on what you have. However, I honestly don't see how here.
Thanks, FL. I think it's just a bit of all the frustration from the past weekend this took to build getting to me. Like, I was working on it from day into the early morning each day, so I'm really spent. I never thought I could get so stressed out from a keyboard build. :P
I need to work on the Lightpad next. Cool thing since it's black too, so it'll match perfectly. Then after that I think I'm taking a break, haha.
Always looking forward to what awesome keyboard you're making/modifying next. :thumb:
I have got to try changing up one of my keyboards, if only to take it apart and put it back together again. Looks like a fun pasttime.
Post by: bocahgundul on Mon, 28 March 2016, 07:41:02
Yep white goes perfectly with blacksSolid white color! and its gonna be a dankest board everOMG E3E dat board is a beast omg. the only cons is that childish led :p
Thanks man, that definitely makes me happy to hear. :) This build has been soooo stressful, hahaha.
Yep, I think I'll either turn them off or make them a solid color or something. I haven't even programmed the firmware. I just wanted to finally finish this one, haha.
Oh, white? Good idea! That wasn't even on my mind.
or green, green is perfect too
Post by: Pemdas on Mon, 28 March 2016, 08:05:36
Hotswappable Alps Orion v2 with Alps SKCM Blue + SKCL Brown for Caps Lock and Scroll Lock with green LEDs. Dyed AT101 PBT caps. I tried dyeing two sample spacebars, but they warped easily and just came out an ugly brown, so I used Krylon Fusion on the space bar. Waiting for the paint to fully cure in a week before I mount it. I just set up up for these photos. :P
Oh right, I used Duplicolor Metalcast "Smoke" to darken the stainless steel plate:Show Image(http://i.imgur.com/nQwK92z.jpg)Show Image(http://i.imgur.com/AnMpR8og.jpg)
So here's the board:Show Image(http://i.imgur.com/GuOjR9X.jpg)Show Image(http://i.imgur.com/AC3hJ8d.jpg)Show Image(http://i.imgur.com/iHUowkD.jpg)
My Orion v2 possesses the power of levitation!Show Image(http://i.imgur.com/RoEI78c.jpg)Show Image(http://i.imgur.com/UgOSrs7.jpg)
Here you can clearly see the holtite sockets used for the hotswap mod. I'm not sure how I feel about this bottom as it makes the board feel like nothing more than a top bezel with feet, lol.Show Image(http://i.imgur.com/IarsCf3.jpg)
Stealthy in the background with my first Duck in the foreground. :3
I wanted the Alphas to be a lighter greyish black, and they technically are, but I think I left them in a wee bit too long. Now it looks like I just have a BoB stealth board, which is pretty cool. I have IBM 5140 caps I could use for a piano white and black look and SGI caps I could use if I want to redo the lighter keys in that grey color I was thinking of.
What do you guys thing? Good as is?
It's been one hell of a week. The hotswap mod and this build has drained the hell out of me. :confused:
Oh man best Orion v2 so far! Hotswappable switches is such a cool feature, definitely worth the work you put in imo :thumb: The dye job on the caps look fantastic too.
The painted plate is sweet too, I saw it on a couple other builds as well but totally forgot when I put mine together :( I'll definitely have to keep it in mind for my next build. It's a really nice touch!
Post by: rainb1ood on Mon, 28 March 2016, 08:57:53
I love the minimalist look of the final product and hotswappable alps too!
Post by: chilldude_22 on Mon, 28 March 2016, 09:19:44
Hotswappable Alps Orion v2 with Alps SKCM Blue + SKCL Brown for Caps Lock and Scroll Lock with green LEDs. Dyed AT101 PBT caps. I tried dyeing two sample spacebars, but they warped easily and just came out an ugly brown, so I used Krylon Fusion on the space bar. Waiting for the paint to fully cure in a week before I mount it. I just set up up for these photos. :P
Oh right, I used Duplicolor Metalcast "Smoke" to darken the stainless steel plate:Show Image(http://i.imgur.com/nQwK92z.jpg)Show Image(http://i.imgur.com/AnMpR8og.jpg)
So here's the board:Show Image(http://i.imgur.com/GuOjR9X.jpg)Show Image(http://i.imgur.com/AC3hJ8d.jpg)Show Image(http://i.imgur.com/iHUowkD.jpg)
My Orion v2 possesses the power of levitation!Show Image(http://i.imgur.com/RoEI78c.jpg)Show Image(http://i.imgur.com/UgOSrs7.jpg)
Here you can clearly see the holtite sockets used for the hotswap mod. I'm not sure how I feel about this bottom as it makes the board feel like nothing more than a top bezel with feet, lol.Show Image(http://i.imgur.com/IarsCf3.jpg)
Stealthy in the background with my first Duck in the foreground. :3
I wanted the Alphas to be a lighter greyish black, and they technically are, but I think I left them in a wee bit too long. Now it looks like I just have a BoB stealth board, which is pretty cool. I have IBM 5140 caps I could use for a piano white and black look and SGI caps I could use if I want to redo the lighter keys in that grey color I was thinking of.
What do you guys thing? Good as is?
It's been one hell of a week. The hotswap mod and this build has drained the hell out of me. :confused:
You've done it again! Brilliant work. Incredible board.
Post by: ika on Tue, 29 March 2016, 21:43:44
Post by: E3E on Tue, 29 March 2016, 22:00:38
It's too much sometimes!
Anyway, if anyone would happen to have a brass weight for the aluminum bottom of the Orion v2 and wouldn't mind selling it, please let me know!
(http://i.imgur.com/2chf2f4.jpg)
Really liking the look of the "dynamic duo" as I call them. :P No more Jukebox or Cherry MX for my Lightpad now, haha.
Post by: E3E on Tue, 29 March 2016, 22:03:32
Oh man best Orion v2 so far! Hotswappable switches is such a cool feature, definitely worth the work you put in imo :thumb: The dye job on the caps look fantastic too.
The painted plate is sweet too, I saw it on a couple other builds as well but totally forgot when I put mine together :( I'll definitely have to keep it in mind for my next build. It's a really nice touch!
Oh man, I missed your post earlier! Thanks man, that means a lot to me since the job was so stressful. PART of my reasoning of all the hotswap modding I do is so I can get more out of my boards and really feel like I have an endgame instead of, well... needing to buy more boards and justifying it by saying I want to build one with switch A or B or C, haha. I don't think I'll be swapping the blues out of the Orion v2 any time soon though.
I have a little aluminum carrying case I bought for my Octagon (which ended up getting its own custom case ) that fits the Orion v2 well, so that's where it'll be stored for now, haha. How are you liking your own Alps v2?
Do you think it'll be your daily driver, or are you going to switch back to the MX PCB and plate?
You've done it again! Brilliant work. Incredible board.
Amazing work as usual E3E!
I love the minimalist look of the final product and hotswappable alps too!
Thanks again, guys. :D I didn't have many options when it came to owning an Alps Orion v2; I feel lucky that I even had the opportunity since not many people ordered one. Black was never a color I really thought about having on a custom, but I ended up with a black Lightpad because it's what was available (I wanted silver), and then ended up withe a black Orion v2, which just so happens to really work well with the Lightpad, so it turned out just amazing in the end. ^-^
I usually like flashy builds with vibrant colors, but my first little keyboard build, with the Rapoo KX as a base, was blacked out (http://i.imgur.com/PSdHKST.jpg), and so this is like... that reborn. Blacked out minimalist stealth looks are nice in their own way.
I know, that Rapoo KX pic is so lame. :))
Post by: ctrlX on Wed, 30 March 2016, 13:50:03
I'm doubting this, but would anyone happen to have a brass weight for the Orion v2 they wouldn't mind passing along? That's one of the last things I'd like for my build. I'm generally toning down my investment in the keyboard hobby a bit as it is. Just want to get the weight and then a case for the other Eagle I have and then I'm going to take a break on everything but taking assembly requests.
It's too much sometimes!
Anyway, if anyone would happen to have a brass weight for the aluminum bottom of the Orion v2 and wouldn't mind selling it, please let me know!Show Image(http://i.imgur.com/2chf2f4.jpg)
Really liking the look of the "dynamic duo" as I call them. :P No more Jukebox or Cherry MX for my Lightpad now, haha.
Really nice work there. Looks great! Makes me think of the Lockheed F-117 Nighthawk ;)
Post by: ctrlX on Wed, 30 March 2016, 13:55:26
Noticed the other day that 2 of my switches have a very subtle "springy" sound. I want to pop the top off and see what is going on inside. Maybe add some extra lube and/or change the springs. As soon as I tried taking the top off the plastic started to bend and would have eventually cracked if more force was applied. The top was nowhere near of coming off.
Any suggestions? Thanks in advance.
P.S. Switches are Zealios, which are known to be a bit more sensitive.
Post by: ika on Wed, 30 March 2016, 16:19:50
Has anyone successfully removed the top housing using the clippers method on soldered switches on the Orion with steel plate?
Noticed the other day that 2 of my switches have a very subtle "springy" sound. I want to pop the top off and see what is going on inside. Maybe add some extra lube and/or change the springs. As soon as I tried taking the top off the plastic started to bend and would have eventually cracked if more force was applied. The top was nowhere near of coming off.
Any suggestions? Thanks in advance.
P.S. Switches are Zealios, which are known to be a bit more sensitive.
You have to desolder. The plate doesn't support switch top removal.
Post by: ctrlX on Wed, 30 March 2016, 16:29:35
Ah, I see. Thanks for the info.Has anyone successfully removed the top housing using the clippers method on soldered switches on the Orion with steel plate?
Noticed the other day that 2 of my switches have a very subtle "springy" sound. I want to pop the top off and see what is going on inside. Maybe add some extra lube and/or change the springs. As soon as I tried taking the top off the plastic started to bend and would have eventually cracked if more force was applied. The top was nowhere near of coming off.
Any suggestions? Thanks in advance.
P.S. Switches are Zealios, which are known to be a bit more sensitive.
You have to desolder. The plate doesn't support switch top removal.
Post by: FrostyToast on Wed, 30 March 2016, 16:39:43
There are a couple of areas in which we can explain this: through production logistics and principles of alps switches.
Now, production is simple: less options, less cost. Since alps isn't very popular to begin with, having only one plate option is the only viable route.
Now here's a wall of text to give you a little alps crash course.
Alps also have an issue with its mounting method; it's ****. Alps switches MUST have a plate to mount to otherwise there is zero stability due to he fact that alps switches were never designed for pcb mounting; unlike MX switches which can attach to the pcb via extra legs.
This would mean that all stability would have to rely on the integrity of the plate which requires two things: distinctive mounting cutouts and a strong material.
Plates for alps cannot offer multiple layout configurations because that would imply crossover between mounting cutouts resulting in the switch not having anything to mount to on on or more sides. Unlike MX switches alps cannot compensate by also attaching itself to another component like the pcb.
Sturdiness is the other issue and is the main reason why alps plates are almost always steel. Though other materials, especially when looking at tactile switches, see benefits in acoustics and tactility, a soft material such as plastic would fail to mount the switch properly and would result in a very unsatisfactory feel and questionable integrity. Additionally, even aluminum in comparison to steel is considered quite soft and will fail to provide the most satisfactory security for mounting. Stainless steel on the other hand is the most accessible strong material out there and is the prime candidate to offer stability for misting alps switches.
TLDR: Alps switches have trash design and require a stainless steel plate to be mounted properly.
Post by: E3E on Wed, 30 March 2016, 17:15:56
Super late addition to the question of plate materials for alps.
There are a couple of areas in which we can explain this: through production logistics and principles of alps switches.
Now, production is simple: less options, less cost. Since alps isn't very popular to begin with, having only one plate option is the only viable route.
Now here's a wall of text to give you a little alps crash course.
Alps also have an issue with its mounting method; it's ****. Alps switches MUST have a plate to mount to otherwise there is zero stability due to he fact that alps switches were never designed for pcb mounting; unlike MX switches which can attach to the pcb via extra legs.
This would mean that all stability would have to rely on the integrity of the plate which requires two things: distinctive mounting cutouts and a strong material.
Plates for alps cannot offer multiple layout configurations because that would imply crossover between mounting cutouts resulting in the switch not having anything to mount to on on or more sides. Unlike MX switches alps cannot compensate by also attaching itself to another component like the pcb.
Sturdiness is the other issue and is the main reason why alps plates are almost always steel. Though other materials, especially when looking at tactile switches, see benefits in acoustics and tactility, a soft material such as plastic would fail to mount the switch properly and would result in a very unsatisfactory feel and questionable integrity. Additionally, even aluminum in comparison to steel is considered quite soft and will fail to provide the most satisfactory security for mounting. Stainless steel on the other hand is the most accessible strong material out there and is the prime candidate to offer stability for misting alps switches.
TLDR: Alps switches have trash design and require a stainless steel plate to be mounted properly.
I don't even remember when this question was asked, but I don't agree that Alps needs a stainless steel plate, let alone one made of metal at all. There were plenty of Alps boards back in the day that used plastic plates. The crappiness factor of plastic is something I've seen a lot of people using plastic plates on their Orion v2s express though and that's for MX.
I use a carbon fiber universal plate with Cherry stabs on my Hammer Alps (https://geekhack.org/index.php?topic=77497.msg1952047#msg1952047) (Eagle) build and it doesn't have any issues. I'd say aluminum would be just fine with Alps and universal cut outs would not be a huge obstacle as long as at least two sides are supported; that's just from my experience. I used LeandreN's plate for the two Eagles I built with Alps switches since the notches just happen to support Alps switch mounting very well. They are not THAT sensitive. I'm even using PCB mounted switches on my Lightpad until the plate I'm having made for it comes in since I've hotswap modded it for Alps as well and wanted it to at least look complete until the plate arrives. :P
They aren't that trash, now. ^-^
Post by: FrostyToast on Wed, 30 March 2016, 17:38:58
I have alps board where several switches have become loose to the point where I could probably pull them straight out with my fingers. In fact, I had a friend who did that with every single switch of the board so effortlessly so as to not damage the switches in any significant way.
Post by: E3E on Wed, 30 March 2016, 17:48:27
I would be more concerned for how such boards would stand the test of time.
I have alps board where several switches have become loose to the point where I could probably pull them straight out with my fingers. In fact, I had a friend who did that with every single switch of the board so effortlessly so as to not damage the switches in any significant way.
You mean even while they were soldered in? I've seen some Alps boards with poor soldering jobs where the contact pins separated from the pads before, so that seems likely, but I've only seen that on poor quality boards like Focus FK2001s.
As far as my modded builds, they are hotswappable so they are meant to be pulled out of their sockets. Except pulling them straight out with your fingers is practically impossible. The combination of a plate and the sockets makes it absolutely brutal to do without a tool. They have been holding up pretty well for the past couple of months of use and haven't had any issues even with some switch swaps and layout changes put in.
In your case, it seems like a combination of the plate retaining "wings" becoming flattened and the contacts breaking off of the pads on the PCB, which is just ridiculous, haha. On Alps Electric branded PCBs, I've mainly seen only quality solder jobs. Daewoo (Leading Edge) and Zenith as well. I think some of the Taiwanese companiese, not all of them,but some, had really low standards of quality.
Post by: appleonama on Fri, 01 April 2016, 07:00:09
I don't know what to do :))
edit: the pcb is always on flip mode
(http://i.imgur.com/vpFLVIB.png)
(http://i.imgur.com/wISWb99.png)
Post by: rainb1ood on Fri, 01 April 2016, 07:11:29
Post by: appleonama on Fri, 01 April 2016, 16:38:06
Did you try the --force option?
doesn't allow me it just runs through its operations till the end
Post by: E3E on Fri, 01 April 2016, 16:42:07
Did you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
Post by: appleonama on Fri, 01 April 2016, 16:48:00
Did you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Post by: aznairjordan on Fri, 01 April 2016, 19:13:33
Did you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
Post by: appleonama on Fri, 01 April 2016, 19:24:28
yes please I will appreciate! please and thank youDid you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
Post by: appleonama on Fri, 01 April 2016, 19:26:58
Post by: aznairjordan on Fri, 01 April 2016, 19:27:01
yes please I will appreciate! please and thank youDid you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
this is from filphil:
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
It worked for me so hopefully it can do the same for you!
Post by: appleonama on Fri, 01 April 2016, 19:30:52
yes please I will appreciate! please and thank youDid you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
this is from filphil:
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
It worked for me so hopefully it can do the same for you!
ahh aright its similar to this guide
http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docx
maybe I have to do all the same steps with this new pcb.
my other orion pcb works completely fine but this new one as shown is always on flip mode.
Post by: aznairjordan on Fri, 01 April 2016, 19:32:17
I did it that way at first and it was working for my until I did something weird and thought I bricked it. Followed the guide I linked you and it was perfectyes please I will appreciate! please and thank youDid you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
this is from filphil:
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
It worked for me so hopefully it can do the same for you!
ahh aright its similar to this guide
http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docx
maybe I have to do all the same steps with this new pcb.
my other orion pcb works completely fine but this new one as shown is always on flip mode.
Post by: appleonama on Fri, 01 April 2016, 22:40:42
I did it that way at first and it was working for my until I did something weird and thought I bricked it. Followed the guide I linked you and it was perfectyes please I will appreciate! please and thank youDid you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
this is from filphil:
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
It worked for me so hopefully it can do the same for you!
ahh aright its similar to this guide
http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docx
maybe I have to do all the same steps with this new pcb.
my other orion pcb works completely fine but this new one as shown is always on flip mode.
Got it to work bro thanks!
I didn't follow the link but I started to mess around with the atmel flip program. The chip was blank so all I had to do was load the flip file into the chip. After that the board could be programmed with 02d time to build my aluminum orion!
Post by: aznairjordan on Fri, 01 April 2016, 22:59:23
Glad you got it to work :) was a huge relief to me when I got the board to work so I'm happy if I was in any way helpful to you too!I did it that way at first and it was working for my until I did something weird and thought I bricked it. Followed the guide I linked you and it was perfectyes please I will appreciate! please and thank youDid you try the --force option?
doesn't allow me it just runs through its operations till the end
Did you get this PCB to replace your original broken one?
yeah this is the one from duck0013 I ordered like 3 months ago
but now I can't use it LOL :'(
Your error messages kinda look like mine from before and filphil was the one that helped me trouble shoot it. I ended up downloading the Amtel flip program to get it back up. If you want me to dig for his help, just let me know :)
this is from filphil:
https://geekhack.org/index.php?topic=49647.0
The steps are there. Major differences are that you'll be using the 02d software to make your hex file, hold back space to bring your orion to programming mode when you're plugging it in, and the controller chip name will be located on your pcb.
It worked for me so hopefully it can do the same for you!
ahh aright its similar to this guide
http://www.adamfalwell.com/projects/octagon/assets/-simplified-guide--duck-pcb-flash-firmware---keymapping.docx
maybe I have to do all the same steps with this new pcb.
my other orion pcb works completely fine but this new one as shown is always on flip mode.
Got it to work bro thanks!
I didn't follow the link but I started to mess around with the atmel flip program. The chip was blank so all I had to do was load the flip file into the chip. After that the board could be programmed with 02d time to build my aluminum orion!
Post by: E3E on Sat, 02 April 2016, 19:14:59
(http://i.imgur.com/w1ICPPN.jpg)
(http://i.imgur.com/wFnEoE8.jpg)
(http://i.imgur.com/I9jo4bP.jpg)
I did this all by hand with a dremel because I'm crazy (and cheap).
I still have to polish it, and I'm waiting for brass screws, but yep.
Post by: naasfu on Sat, 02 April 2016, 19:19:09
I really wanted a weight for my Orion v2:Show Image(http://i.imgur.com/w1ICPPN.jpg)Show Image(http://i.imgur.com/wFnEoE8.jpg)Show Image(http://i.imgur.com/I9jo4bP.jpg)
I did this all by hand with a dremel because I'm crazy (and cheap).
I still have to polish it, and I'm waiting for brass screws, but yep.
can confirm, E3E is crazy.
that's really cool though. :) are you also thinking of engraving something on it?
Post by: E3E on Sat, 02 April 2016, 19:51:32
can confirm, E3E is crazy.
that's really cool though. :) are you also thinking of engraving something on it?
Thanks man! ^-^
I might eventually! If I did it myself, I'd have to practice a bit before I dare take the plunge, haha.
This is pretty awesome though! It bumped the weight up from 5 lbs 15 oz to 7 lbs 8 oz. Super cool!
Post by: Pemdas on Sat, 02 April 2016, 20:13:03
I really wanted a weight for my Orion v2:Show Image(http://i.imgur.com/w1ICPPN.jpg)Show Image(http://i.imgur.com/wFnEoE8.jpg)Show Image(http://i.imgur.com/I9jo4bP.jpg)
I did this all by hand with a dremel because I'm crazy (and cheap).
I still have to polish it, and I'm waiting for brass screws, but yep.
Oh man I might have to give this a shot.
Did you just buy a brass block and shape it yourself? :eek:
Very cool :thumb: :thumb:
Post by: E3E on Sat, 02 April 2016, 20:22:16
Oh man I might have to give this a shot.
Did you just buy a brass block and shape it yourself? :eek:
Very cool :thumb: :thumb:
I'd go for it if I were you! Drilling the screw holes was the trickiest part (keep spraying down the part with a lubricant, it helps a ton). Cutting the .75~ inches from the width needed to make it fit was also very tedious.
It isn't perfect, but I think it still looks great! Just waiting for those brass screws now.
I used copper, since, if I couldn't get an official brass weight from Korea, I figured I'd do one better and use copper since it's heavier. The brass screws should add some weight too, haha.
I used a 12 x 4 x 1/8" plate. The recess is only 1/10th of an inch thick, but 1/8th works just fine.
Yeah, I did it all by hand. I had no idea what the CNC would cost, so I decided to just do it myself. It's hardly ever going to be seen anyway, since it's under the top, but I tried to do it as carefully as possible.
If CNC wouldn't cost much, then it wouldn't be too expensive to just have it done somewhere since the copper plate only cost $24. :)
http://www.ebay.com/itm/281290504531?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
This is what I bought.
If you want the traditional brass look, this should work~
http://www.ebay.com/itm/BRASS-SHEET-11ga-4-x-12-x-1-8-THICK-/301743434556?hash=item46414f6b3c:g:v9QAAOSwu4BVw~wq
Oh yeah, how's your Alps Orion v2, man? Have you decided on keeping the Alps plate in the board, or do you prefer Cherry? I'm super curious to hear if we have another Alps fan here. :D You used Alps SKCL Green, right? Lovely switch. :)
Post by: aznairjordan on Sat, 02 April 2016, 20:28:17
Oh man I might have to give this a shot.
Did you just buy a brass block and shape it yourself? :eek:
Very cool :thumb: :thumb:
I'd go for it if I were you! Drilling the screw holes was the trickiest part (keep spraying down the part with a lubricant, it helps a ton). Cutting the .75~ inches from the width needed to make it fit was also very tedious.
It isn't perfect, but I think it still looks great! Just waiting for those brass screws now.
I used copper, since, if I couldn't get an official brass weight from Korea, I figured I'd do one better and use copper since it's heavier. The brass screws should add some weight too, haha.
I used a 12 x 4 x 1/8" plate. The recess is only 1/10th of an inch thick, but 1/8th works just fine.
Yeah, I did it all by hand. I had no idea what the CNC would cost, so I decided to just do it myself. It's hardly ever going to be seen anyway, since it's under the top, but I tried to do it as carefully as possible.
If CNC wouldn't cost much, then it wouldn't be too expensive to just have it done somewhere since the copper plate only cost $24. :)
http://www.ebay.com/itm/281290504531?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
This is what I bought.
If you want the traditional brass look, this should work~
http://www.ebay.com/itm/BRASS-SHEET-11ga-4-x-12-x-1-8-THICK-/301743434556?hash=item46414f6b3c:g:v9QAAOSwu4BVw~wq
Oh yeah, how's your Alps Orion v2, man? Have you decided on keeping the Alps plate in the board, or do you prefer Cherry? I'm super curious to hear if we have another Alps fan here. :D You used Alps SKCL Green, right? Lovely switch. :)
... Can I commission you to make one for me too?!?!?
Post by: Pemdas on Sun, 03 April 2016, 01:52:55
Oh man I might have to give this a shot.
Did you just buy a brass block and shape it yourself? :eek:
Very cool :thumb: :thumb:
I'd go for it if I were you! Drilling the screw holes was the trickiest part (keep spraying down the part with a lubricant, it helps a ton). Cutting the .75~ inches from the width needed to make it fit was also very tedious.
It isn't perfect, but I think it still looks great! Just waiting for those brass screws now.
I used copper, since, if I couldn't get an official brass weight from Korea, I figured I'd do one better and use copper since it's heavier. The brass screws should add some weight too, haha.
I used a 12 x 4 x 1/8" plate. The recess is only 1/10th of an inch thick, but 1/8th works just fine.
Yeah, I did it all by hand. I had no idea what the CNC would cost, so I decided to just do it myself. It's hardly ever going to be seen anyway, since it's under the top, but I tried to do it as carefully as possible.
If CNC wouldn't cost much, then it wouldn't be too expensive to just have it done somewhere since the copper plate only cost $24. :)
http://www.ebay.com/itm/281290504531?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
This is what I bought.
If you want the traditional brass look, this should work~
http://www.ebay.com/itm/BRASS-SHEET-11ga-4-x-12-x-1-8-THICK-/301743434556?hash=item46414f6b3c:g:v9QAAOSwu4BVw~wq
Oh yeah, how's your Alps Orion v2, man? Have you decided on keeping the Alps plate in the board, or do you prefer Cherry? I'm super curious to hear if we have another Alps fan here. :D You used Alps SKCL Green, right? Lovely switch. :)
Thanks for the links, ordered one of the copper sheets! You're an inspiration E3E :thumb:
It's crazy how much weight such a thin plate adds to the board! I've got to dig up my dremel from somewhere in the garage now....
And as far as liking alps over cherry, I could never choose a favorite between Cherry/Alps/Topre! They all feel great in their own way and are different enough to justify keeping all of them around. I don't think I could choose one as objectively better than the rest. I usually change keyboards multiple times a day cause I love the feel of changing switches so much. But for what it's worth I'm pretty sure I'm going to keep my Orion v2 as an alps board just because of how unique and awesome it is! I do really miss my pretty mx keycaps though :(
Post by: ramnes on Sun, 03 April 2016, 14:48:23
Would anyone be interested in a small GB for an alternative anodized Orion v2 plate, with cutouts that allow switch opening?
Post by: filphil on Sun, 03 April 2016, 19:05:57
(http://kbdlab.co.kr/files/attach/images/121/888/088/003/2537e66442b3bd2aef10ccf95c7a6b70.jpg)
At one point in time I was planning on getting a few made but my source has been infinitely busy with other projects. Plus my interest in keyboards has taken a dive so the motivation just isn't there.
The plate adds a noticeable amount of weight. It's a real treat.
Post by: appleonama on Sun, 03 April 2016, 20:43:02
just need sherry to replace my less than key and alt. maybe my 8 and l for the blue smudges
(http://i.imgur.com/WiJtb76.jpg)
Post by: omgar on Sun, 03 April 2016, 21:54:53
so this is my near complete orion
just need sherry to replace my less than key and alt. maybe my 8 and l for the blue smudgesShow Image(http://i.imgur.com/WiJtb76.jpg)
Looks fantastic!
Post by: GOGOMA on Mon, 04 April 2016, 04:15:15
Korean alphabet "Hangeul" = Orion
Lee Sunshin pont
(http://i.imgur.com/fZl4qKV.jpg)
(http://i.imgur.com/7PvkTUD.jpg)
(http://i.imgur.com/LJTLB8o.jpg)
Post by: duckness on Mon, 04 April 2016, 04:36:59
Orion v2 Brass plate
Korean alphabet "Hangeul" = Orion
Lee Sunshin pontShow Image(http://i.imgur.com/fZl4qKV.jpg)Show Image(http://i.imgur.com/7PvkTUD.jpg)Show Image(http://i.imgur.com/LJTLB8o.jpg)
holy **** omg
Post by: appleonama on Mon, 04 April 2016, 04:47:21
Orion v2 Brass plate
Korean alphabet "Hangeul" = Orion
Lee Sunshin pontShow Image(http://i.imgur.com/fZl4qKV.jpg)Show Image(http://i.imgur.com/7PvkTUD.jpg)Show Image(http://i.imgur.com/LJTLB8o.jpg)
share with us man!
Post by: popkorn62 on Mon, 04 April 2016, 05:01:59
Orion v2 Brass plateThis is cray! Now I want an Orion more than everrr
Korean alphabet "Hangeul" = Orion
Lee Sunshin pontShow Image(http://i.imgur.com/fZl4qKV.jpg)Show Image(http://i.imgur.com/7PvkTUD.jpg)Show Image(http://i.imgur.com/LJTLB8o.jpg)
Post by: E3E on Mon, 04 April 2016, 16:19:53
Orion v2 Brass plate
Korean alphabet "Hangeul" = Orion
Lee Sunshin pontShow Image(http://i.imgur.com/fZl4qKV.jpg)Show Image(http://i.imgur.com/7PvkTUD.jpg)Show Image(http://i.imgur.com/LJTLB8o.jpg)
share with us man!
Seems super unlikely, lol. That's why I made my own. Get one CNC'd. We already have the file for it.
Post by: elton5354 on Tue, 05 April 2016, 18:40:52
There isn't much to update, but the 1st batch should be ready soon..
Opps wrong thread
Post by: missalaire on Tue, 05 April 2016, 19:27:35
Post by: appleonama on Tue, 05 April 2016, 20:48:22
Orion v2 Brass plate
Korean alphabet "Hangeul" = Orion
Lee Sunshin pontShow Image(http://i.imgur.com/fZl4qKV.jpg)Show Image(http://i.imgur.com/7PvkTUD.jpg)Show Image(http://i.imgur.com/LJTLB8o.jpg)
share with us man!
Seems super unlikely, lol. That's why I made my own. Get one CNC'd. We already have the file for it.
so he just came here to shiz post
Post by: concertomi on Thu, 07 April 2016, 07:09:55
Post by: JaccoW on Thu, 07 April 2016, 08:09:45
WTB flat acrylic clear bottom if anyone is willing to part with theirs.Are they similar to the V1? Because I have a few of those left.
Post by: E3E on Thu, 07 April 2016, 09:01:42
WTB flat acrylic clear bottom if anyone is willing to part with theirs.Are they similar to the V1? Because I have a few of those left.
I think you're thinking of the acrylic side insert wedges. Alaire wants the flat acrylic bottom that you can mount the top frame/bezel onto.
The side inserts for the aluminum bottom are similar to the V1 though, but I have no idea if they'd fit perfectly or not.
Post by: missalaire on Tue, 12 April 2016, 00:02:31
WTB flat acrylic clear bottom if anyone is willing to part with theirs.Are they similar to the V1? Because I have a few of those left.
I think you're thinking of the acrylic side insert wedges. Alaire wants the flat acrylic bottom that you can mount the top frame/bezel onto.
The side inserts for the aluminum bottom are similar to the V1 though, but I have no idea if they'd fit perfectly or not.
Yep, the flat acrylic bottom not the side inserts.
Post by: aznairjordan on Tue, 12 April 2016, 01:15:43
Hello I just built my Orion v2 and flashed the default firmware over. Somehow the LEDs on the letters and the function rows seem to keep blinking slowly. Any idea what I should modify on the firmware? Any help much appreciated!
there are instructions on how to map your keys and I believe you just need to change the led control on the board!
Post by: JaccoW on Tue, 12 April 2016, 08:39:10
That's what I thought. I had some plates lasercut (check my SIG for pics of the plate) but I never got around to selling them. They were too thin to show up in between the two aluminum layer and I would have needed new screws.WTB flat acrylic clear bottom if anyone is willing to part with theirs.Are they similar to the V1? Because I have a few of those left.
I think you're thinking of the acrylic side insert wedges. Alaire wants the flat acrylic bottom that you can mount the top frame/bezel onto.
The side inserts for the aluminum bottom are similar to the V1 though, but I have no idea if they'd fit perfectly or not.
Yep, the flat acrylic bottom not the side inserts.
I bought some a spare set of side inserts as well but I've used all of them.
Post by: E3E on Wed, 13 April 2016, 15:57:07
That's what I thought. I had some plates lasercut (check my SIG for pics of the plate) but I never got around to selling them. They were too thin to show up in between the two aluminum layer and I would have needed new screws.
I bought some a spare set of side inserts as well but I've used all of them.
Oh, then I hope you can help missalaire out then!
I just got my Duck Feet in today from Alienman82, and it's given me a renewed interest in the flat acrylic bottom! I do love the weight of my aluminum bottom with its copper weight, but there's something cool about the lightness of the flat bottom setup and it's nice to see all the gold holtite sockets from my hotswap mod when I turn it over. The duck feet just make it.
(http://i.imgur.com/BnqtFwT.jpg)
(http://i.imgur.com/qgm0T1T.jpg)
(http://i.imgur.com/FPcoUWm.jpg)
Excuse the potatoes, I just snapped them quick!
Post by: E3E on Wed, 13 April 2016, 18:14:27
(http://i.imgur.com/eTslIbl.jpg)
(http://i.imgur.com/p2k31Sr.jpg)
This is the coolest thing about the flat bottom, I think. Still, I dunno how I ultimately feel about it compared to the aluminum bottom. :P
Post by: lootbag on Wed, 13 April 2016, 19:06:52
I hope to experiment with making my own flat bottom for the Octagon V2 when it arrives.
You also got me interested in the world of ALPS and I managed to snag a Zenith 100-1886 recently.
Post by: filphil on Wed, 13 April 2016, 19:33:41
Just a few more pictures:Show Image(http://i.imgur.com/eTslIbl.jpg)Show Image(http://i.imgur.com/p2k31Sr.jpg)
This is the coolest thing about the flat bottom, I think. Still, I dunno how I ultimately feel about it compared to the aluminum bottom. :P
What's the angle with the duck feet? The flat bottom feels great without a wrist rest, IMO. The high angle of the aluminum works well otherwise for my purpose.
Plus the flat bottom and acrylic anged bottoms have a nice light show.
Post by: hammelgammler on Thu, 14 April 2016, 03:57:14
Post by: ctrlX on Thu, 14 April 2016, 10:16:54
- If I disconnect the USB cable and reconnect it, my function row LEDs are always brighter than the rest. This also sometimes happen after reboot. I then have to go into LED control mode and adjust the brightness. Sometimes I have to do this several times before all my LEDs are adjusted to the same brightness level.
- If I press keys fast and continuously, after a while the LEDs start to dim down until the are no longer lit. Sometimes they even flicker just before they are no longer lit.
Does the description above make any sense? I can upload a vid if it doesn't.
I reckon with all the fast typers here at GH someone else should have noticed this strange behavior :rolleyes:
NOTE: My LEDs are not set to any fancy pulsating or other function. Just regular ON and then adjusted brightness, three steps above the lowest.
Post by: appleonama on Thu, 14 April 2016, 21:50:08
Just a few more pictures:Show Image(http://i.imgur.com/eTslIbl.jpg)Show Image(http://i.imgur.com/p2k31Sr.jpg)
This is the coolest thing about the flat bottom, I think. Still, I dunno how I ultimately feel about it compared to the aluminum bottom. :P
How did you make the holes on the flat acrylic? I just got my duck feet today but I don't want to ruin my flat piece D:
Post by: JaccoW on Fri, 15 April 2016, 01:35:13
Alright, so I found a place nearby that has a wide range of quality acrylic Bouwplastics.nl (http://www.bouwplastics.nl/webshop/plaatmateriaal) and I will ask them to make me one of the plates and a set of side-inserts.
Other than the side window dimensions (http://duck0113.tistory.com/94), the DXF-files (http://kbdlab.co.kr/index.php?mid=board_tune&document_srl=153206) and the plate drawings, what other info should I send them?
I believe the bottom plate (http://kbdlab.co.kr/index.php?mid=board_housing&document_srl=158172) was 2mm and the side windows 12mm? Will they be able to lasercut it based on just that?
Just went to pick them up.(http://i.imgur.com/ZnatxgNh.jpg) (http://imgur.com/ZnatxgN)
Behold, bottom plates!Show Image(http://i.imgur.com/aJw5j1Ch.jpg)
9 plates in total.Show Image(http://i.imgur.com/BbTCnxzh.jpg)
With some feetShow Image(http://i.imgur.com/ZMwpoYnh.jpg)
Roughly a 5 degree angle
Now I need to be patient for my orion to arrive. :P
The place where I got them told me they'd have a machine that could cut the 12mm pieces in one month.
So unless somebody else wants to pick that up in a GB I could try by then.
Post by: appleonama on Fri, 15 April 2016, 01:40:57
About the V1 acrylic plate:Alright, so I found a place nearby that has a wide range of quality acrylic Bouwplastics.nl (http://www.bouwplastics.nl/webshop/plaatmateriaal) and I will ask them to make me one of the plates and a set of side-inserts.
Other than the side window dimensions (http://duck0113.tistory.com/94), the DXF-files (http://kbdlab.co.kr/index.php?mid=board_tune&document_srl=153206) and the plate drawings, what other info should I send them?
I believe the bottom plate (http://kbdlab.co.kr/index.php?mid=board_housing&document_srl=158172) was 2mm and the side windows 12mm? Will they be able to lasercut it based on just that?Just went to pick them up.(http://i.imgur.com/ZnatxgNh.jpg) (http://imgur.com/ZnatxgN)
Behold, bottom plates!Show Image(http://i.imgur.com/aJw5j1Ch.jpg)
9 plates in total.Show Image(http://i.imgur.com/BbTCnxzh.jpg)
With some feetShow Image(http://i.imgur.com/ZMwpoYnh.jpg)
Roughly a 5 degree angle
Now I need to be patient for my orion to arrive. :P
The place where I got them told me they'd have a machine that could cut the 12mm pieces in one month.
So unless somebody else wants to pick that up in a GB I could try by then.
Time to order some for my duckfeet
thanks
Post by: JaccoW on Fri, 15 April 2016, 01:43:42
Again, I'm not sure these are compatible with the V2. I have a few plates left that you are welcome to try though.About the V1 acrylic plate:Alright, so I found a place nearby that has a wide range of quality acrylic Bouwplastics.nl (http://www.bouwplastics.nl/webshop/plaatmateriaal) and I will ask them to make me one of the plates and a set of side-inserts.
Other than the side window dimensions (http://duck0113.tistory.com/94), the DXF-files (http://kbdlab.co.kr/index.php?mid=board_tune&document_srl=153206) and the plate drawings, what other info should I send them?
I believe the bottom plate (http://kbdlab.co.kr/index.php?mid=board_housing&document_srl=158172) was 2mm and the side windows 12mm? Will they be able to lasercut it based on just that?Just went to pick them up.(http://i.imgur.com/ZnatxgNh.jpg) (http://imgur.com/ZnatxgN)
Behold, bottom plates!Show Image(http://i.imgur.com/aJw5j1Ch.jpg)
9 plates in total.Show Image(http://i.imgur.com/BbTCnxzh.jpg)
With some feetShow Image(http://i.imgur.com/ZMwpoYnh.jpg)
Roughly a 5 degree angle
Now I need to be patient for my orion to arrive. :P
The place where I got them told me they'd have a machine that could cut the 12mm pieces in one month.
So unless somebody else wants to pick that up in a GB I could try by then.
Time to order some for my duckfeet
thanks
Post by: E3E on Fri, 15 April 2016, 02:17:42
How did you make the holes on the flat acrylic? I just got my duck feet today but I don't want to ruin my flat piece D:
I used double-sided tape, similar to how I keep the inserts in the board and the duck feet. It's a tape meant for fabric mending and is pretty sticky but not impossible to remove. Better than double-sided scotch tape I'd say. Secure enough for using for the feet. I might make the flat acrylic bottom for drilling, but I doubt I'm doing to do that.
Damn, you're going to get a new separate bottom just for the duck feet? Crazy. :P Actually, they probably aren't that expensive, nevermind, haha.
EDIT: I read Elton mention that the tops between the Orion v2 and v1, as well as their plates, were not compatible between each other, but to be honest, the mounting holes look almost exactly the same. It's hard to say whether or not they are though.
Post by: appleonama on Fri, 15 April 2016, 02:43:42
ahh okay I thought you drilled the flat acrylic. hmm I don't feel too comfortable using double face tape to secure the duck feet. That might leave a sticky mess and cleaning it might result in some scratches.How did you make the holes on the flat acrylic? I just got my duck feet today but I don't want to ruin my flat piece D:
I used double-sided tape, similar to how I keep the inserts in the board and the duck feet. It's a tape meant for fabric mending and is pretty sticky but not impossible to remove. Better than double-sided scotch tape I'd say. Secure enough for using for the feet. I might make the flat acrylic bottom for drilling, but I doubt I'm doing to do that.
Damn, you're going to get a new separate bottom just for the duck feet? Crazy. :P Actually, they probably aren't that expensive, nevermind, haha.
EDIT: I read Elton mention that the tops between the Orion v2 and v1, as well as their plates, were not compatible between each other, but to be honest, the mounting holes look almost exactly the same. It's hard to say whether or not they are though.
Post by: Venatorious on Fri, 15 April 2016, 04:56:32
ty
Post by: E3E on Fri, 15 April 2016, 13:54:03
ahh okay I thought you drilled the flat acrylic. hmm I don't feel too comfortable using double face tape to secure the duck feet. That might leave a sticky mess and cleaning it might result in some scratches.
I could easily drill the holes as I have a drill press that I used for hotswap modding my PCBs (a manual hand drill pin vise could even do it since it's just acrylic), but if you've already secured dome feet onto your acrylic plate, then you're already looking at scratches. Aluminum is harder than acrylic, haha. Same with the duck feet if they were to be securely mounted.
The adhesive could be removed with alcohol and a microfiber cloth and I'm pretty sure you wouldn't have any scratches from removing the residue.
Hey guys I missed out and really want one, when do you think there will be another GB?
ty
The only time there's ever been a second GB of sorts was the left overs sale (https://geekhack.org/index.php?topic=59861.0) which included the Kingsaver, Lightpad, and both versions of the Duck Mini.
I think another one was the Lightsaver v2 Round 2 GB, but that one didn't work out.
In otherwords, getting another GB is pretty unlikely. Either try and wait for the v3 GB, or try and get an LZ Alps plate and LZ PCB (https://geekhack.org/index.php?topic=80086) and find an LZ board so you can use Alps in a TKL.
Either that or try to find someone willing to sell their Orion v2 with Alps, but not many people ordered those, or you could try and go for a Kingsaver if anyone has one to sell, but also a bit dubious.
Very nice work with the ALPS integration into the Orion V2 (and the Octagon) E3E!
I hope to experiment with making my own flat bottom for the Octagon V2 when it arrives.
You also got me interested in the world of ALPS and I managed to snag a Zenith 100-1886 recently.
Thanks man, it's always a lot of work, but having hotswappable PCBs is pretty awesome and makes changing layouts, LED swapping, or swapping faulty switches a breeze. :) That flat bottom is really pretty but makes the board feel a little too much like a toy for my tastes. I might still use it from time to time though. :)
Post by: aznairjordan on Sun, 24 April 2016, 17:44:00
Post by: Venatorious on Sun, 24 April 2016, 17:47:13
does anyone need an acrylic angled bottom? Willing to let it go for retail + shipping
PM'd
Post by: popkorn62 on Sun, 24 April 2016, 18:28:47
Post by: Venatorious on Sun, 24 April 2016, 18:35:15
Thanks :D
Post by: NoahNHP on Mon, 25 April 2016, 08:32:10
Post by: JaccoW on Mon, 25 April 2016, 12:59:03
(https://i.imgur.com/tXXGh8U.jpg)
Post by: filphil on Mon, 25 April 2016, 14:40:22
Just came across this on Reddit (https://imgur.com/a/jXRIa#tXXGh8U). I think it's just a really cool idea.Show Image(https://i.imgur.com/tXXGh8U.jpg)
Nice to see the idea come to life! E3E suggested I do that a while ago after posting up the patch I picked up from my houston trip but never got around to it(my orion rebuild is still ongoing).
Post by: Pemdas on Wed, 27 April 2016, 04:30:28
Thanks in advance for any answers :cool:
Post by: Venatorious on Thu, 28 April 2016, 23:10:59
I also have a problem, whenever I try to save a config in 02D, it says Run time error 76 path not found.
Anyone got this problem already? I don't know how to fix :\
Post by: filphil on Thu, 28 April 2016, 23:54:32
Not sure what to use for alps PCB, contact Leeku maybe he designed it.
I also have a problem, whenever I try to save a config in 02D, it says Run time error 76 path not found.
Anyone got this problem already? I don't know how to fix :\
https://geekhack.org/index.php?topic=70864.msg2055836#msg2055836
Try to Look at that post and then further down for the method I use. In short you create the hex file with o2d and upload it with FLIP.
Post by: Venatorious on Fri, 29 April 2016, 00:04:37
Post by: filphil on Fri, 29 April 2016, 00:20:17
Just did that, now the Orion won't work or light up anymore. Was I not supposed to keep the erase box checked in FLIP? Did I just seriously **** up? :-\
That's happened to me before. I've just reattempted the flash and it out came out fine.
Make sure you have the proper chip selected. You can see the name of the chip by looking at the pcb near the arrow cluster. It'll say atmel somewhere.
Post by: Venatorious on Fri, 29 April 2016, 00:21:57
Post by: filphil on Fri, 29 April 2016, 00:25:23
Yeah I have tried various times to redo, even restarted computer. Do you have a default hex file you could share with me so I know for sure it isn't my file that is messed up? Thanks
I have a file at home. Currently at work. When you go through the process of flashing does it go through the whole line of checks? I recall everything should be green lit. Sometimes one process gets stuck and it gives you a red or yellow color but afaik doing the process over should work out.
When you create the hex file from o2d are you using the base file with the custom designation?
Post by: Venatorious on Fri, 29 April 2016, 00:32:12
Turns out I wasn't reselecting the hex file after I opened USB connection :confused:
Is there any way to change the lock light colors? Mine is stuck on light blue
Post by: filphil on Fri, 29 April 2016, 00:37:56
Got it to work!!!! ;D
Turns out I wasn't reselecting the hex file after I opened USB connection :confused:
Is there any way to change the lock light colors? Mine is stuck on light blue
Fantastic.
When it comes to switch leds I've no experience yet since I've had difficulty finding an inexpensive source in the US.
Post by: Venatorious on Fri, 29 April 2016, 00:44:03
I have the angled acrylic bottom, so getting the right LED settings are pretty important for me. :)
I like the RGB wave mode, I might start tinkering with keymaps now, I though you had to use the o2d program to upload also, I think FLIP is better glad I don't have to use o2d for keymapping too.
Post by: filphil on Fri, 29 April 2016, 00:49:40
No I didn't mean the switch ones I meant the lock light ones. Aren't they RGB? I got mine secondhand so I don't know if they came with the kit or were sourced separately.
I have the angled acrylic bottom, so getting the right LED settings are pretty important for me. :)
I like the RGB wave mode, I might start tinkering with keymaps now, I though you had to use the o2d program to upload also, I think FLIP is better glad I don't have to use o2d for keymapping too.
If you're talking about the bottom rgb leds then you go to one of the drop down menus in o2d and then a lighting option should be accessible. From then on it should be pretty self explanatory. Save hex file with key mapping and led settings and then upload via flip.
Post by: himynameisbunny on Fri, 29 April 2016, 00:53:06
Post by: Venatorious on Fri, 29 April 2016, 01:00:54
If you're talking about the bottom rgb leds then you go to one of the drop down menus in o2d and then a lighting option should be accessible. From then on it should be pretty self explanatory. Save hex file with key mapping and led settings and then upload via flip.
Yeah that's the change that I made to the board originally when I needed help. What I am talking about are the lock lights near esc.
Also chances are doubtful of another GB with the octagon and other boards that duck is occupied with bunny. I think you will just have to wait for Orion v3...
Post by: filphil on Fri, 29 April 2016, 01:24:25
If you're talking about the bottom rgb leds then you go to one of the drop down menus in o2d and then a lighting option should be accessible. From then on it should be pretty self explanatory. Save hex file with key mapping and led settings and then upload via flip.
Yeah that's the change that I made to the board originally when I needed help. What I am talking about are the lock lights near esc.
Also chances are doubtful of another GB with the octagon and other boards that duck is occupied with bunny. I think you will just have to wait for Orion v3...
Ooh. I don't think those are rgb controlled. If you put an rgb led it'll either cycle through the colors or stay at a single color.
Post by: Venatorious on Fri, 29 April 2016, 01:31:47
Also thanks again, I have it set to RGB right now and it is really awesome :p
Also what can we do with the 5 notification LED's on the arrow cluster? Are those just stuck to default? I don't even has the LED's in right now but it would awesome to configure one to flash orange when you get a new reddit message or something.
Post by: Jin on Wed, 04 May 2016, 21:06:28
Post by: airs on Wed, 04 May 2016, 23:56:04
Post by: baotung on Fri, 06 May 2016, 16:37:14
Post by: Venatorious on Fri, 06 May 2016, 20:55:33
Post by: ipreferpie on Mon, 09 May 2016, 20:51:55
Post by: Venatorious on Mon, 09 May 2016, 20:59:34
Does anyone know if I can use the shapeways ALPS to MX stem adapters on this keyboard and use MX keys on it?
yeah you could but the keys will be higher than usual.
Post by: ipreferpie on Mon, 09 May 2016, 21:05:37
Does anyone know if I can use the shapeways ALPS to MX stem adapters on this keyboard and use MX keys on it?
yeah you could but the keys will be higher than usual.
Thanks! And any suggestions if I should use MX stabilizers (w/ MX to MX stabilizers) or ALPS stabilizers in that case?
Post by: Venatorious on Mon, 09 May 2016, 21:12:43
Post by: missalaire on Mon, 16 May 2016, 15:06:30
Post by: oisw on Mon, 16 May 2016, 16:06:31
Post by: E3E on Tue, 17 May 2016, 22:42:02
(http://i.imgur.com/MaomML9.jpg)
(http://i.imgur.com/Il3AgrN.jpg)
Put my unshined Dell AT101 PBT set on my Orion v2.
Some people dig this look. I'm not really sure, to be honest. I think I like black on black on black a bit more.
Post by: Venatorious on Tue, 17 May 2016, 23:07:36
Post by: ctrlX on Wed, 18 May 2016, 09:25:18
Post by: E3E on Thu, 19 May 2016, 10:32:19
I like very dark keys, but that contrast between black case and greyish keys is awsome. Would not have been just as nice if they were whiter. Once again, really nice setup.
Thanks. ctrlX. Yeah, the AT101 alphas are more of an off-white beige color rather than a white, so there's no popping contrast there. It does give the board this kind of classy retro vintage look, but I do also prefer black. Thanks again for the compliments on my setup. I'm glad I can make it work, haha.
Man where do you get these keycaps... So nice with either look, but I like the BoB more :thumb:
:)
BoB it is!
Post by: ika on Wed, 25 May 2016, 11:48:06
Post by: kitsun8 on Sat, 04 June 2016, 07:10:38
does anyone know if there will be another run?
Post by: ika on Sun, 05 June 2016, 01:59:29
Post by: appleonama on Sun, 05 June 2016, 02:11:47
Still looking for a V2 PCB/plate combo (preferably unbuilt)! Please PM if you have a spare you don't plan on using!I have a pcb and steel plate
however the pcb is not in the best condition. I bought it off another user and some pads are kinda iffy
Post by: AceRuckus on Tue, 14 June 2016, 14:53:04
Post by: ipreferpie on Mon, 08 August 2016, 21:51:23
Post by: Undone on Thu, 11 August 2016, 18:55:47
Anyone know if any Orion v1 parts are interchangeable with Orion v2? Plate/PCB, bottom, etc.
They are not.
"Orion V2 PCB and plate will not fit into Orion V1 and vice versa. Won't fit Kingsaver as well." - elton5354
Source (this thread) (https://geekhack.org/index.php?topic=70864.msg1713200#msg1713200)
Post by: ramnes on Fri, 12 August 2016, 02:34:31
Post by: roostrc0gburn on Fri, 12 August 2016, 12:19:52
Post by: ipreferpie on Fri, 12 August 2016, 14:24:12
anyone want to trade an Orion V2 for an Octagon V2?
Pm'd :)
Post by: Fnzzy on Fri, 12 August 2016, 15:31:51
Post by: roostrc0gburn on Fri, 12 August 2016, 16:07:59
anyone want to trade an Orion V2 for an Octagon V2?
Pm'd :)
to clarify: i have an octagon for trade :thumb:
Post by: ika on Sat, 13 August 2016, 19:26:23
Anyone know if any Orion v1 parts are interchangeable with Orion v2? Plate/PCB, bottom, etc.
They are not.
"Orion V2 PCB and plate will not fit into Orion V1 and vice versa. Won't fit Kingsaver as well." - elton5354
Source (this thread) (https://geekhack.org/index.php?topic=70864.msg1713200#msg1713200)
Actually they are largely interchangeable, the only thing that doesn't work between the two is the V1 plate, which doesn't fit in the V2 top. The LEDs are in different spots between V1 and V2 but if you just care about something to type on, they work fine.
Post by: Kubiedo on Sat, 13 August 2016, 19:35:08
anyone want to trade an Orion V2 for an Octagon V2?
Pm'd :)
to clarify: i have an octagon for trade :thumb:
Are you looking to sell by chance? :)
Post by: E3E on Sat, 13 August 2016, 19:52:41
Anyone know if any Orion v1 parts are interchangeable with Orion v2? Plate/PCB, bottom, etc.
They are not.
"Orion V2 PCB and plate will not fit into Orion V1 and vice versa. Won't fit Kingsaver as well." - elton5354
Source (this thread) (https://geekhack.org/index.php?topic=70864.msg1713200#msg1713200)
Actually they are largely interchangeable, the only thing that doesn't work between the two is the V1 plate, which doesn't fit in the V2 top. The LEDs are in different spots between V1 and V2 but if you just care about something to type on, they work fine.
Yep, this is true. :thumb: The only issue you'd have with a v1 top is if you are using the standalone indicator lights that the v2 offers. Those won't be compatible. I traded Ika for a v1 top because the Alps PCB doesn't use those indicators at all.
Post by: xondat on Tue, 16 August 2016, 07:12:40
Post by: filphil on Tue, 16 August 2016, 08:53:19
I want to make a weight for my friend but can't find the CAD files for the bottom piece anywhere, I've messaged elton already (he hasn't been on though), but if someone can help me that'd be great. :thumb:
idk if this is what you need but there's this
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
Post by: xondat on Tue, 16 August 2016, 09:14:05
I have that file, I just don't know the thickness so that's all I need :pI want to make a weight for my friend but can't find the CAD files for the bottom piece anywhere, I've messaged elton already (he hasn't been on though), but if someone can help me that'd be great. :thumb:
idk if this is what you need but there's this
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
Post by: boo on Tue, 16 August 2016, 09:17:20
I believe it's 3mm. Same as octagon. I would pm Merlin to checkI have that file, I just don't know the thickness so that's all I need :pI want to make a weight for my friend but can't find the CAD files for the bottom piece anywhere, I've messaged elton already (he hasn't been on though), but if someone can help me that'd be great. :thumb:
idk if this is what you need but there's this
http://kbdlab.co.kr/index.php?document_srl=3088888&mid=board_housing
Sent from my iPhone using Tapatalk
Post by: filphil on Sun, 21 August 2016, 16:23:45
Post by: E3E on Sat, 27 August 2016, 20:11:49
(http://i.imgur.com/ONZeA33.jpg)
I'm actually more comfortable with the higher angle of the aluminum bottom, but I still want to hang onto this acrylic bottom.
Post by: Kubiedo on Sat, 27 August 2016, 20:48:23
Post by: filphil on Sat, 27 August 2016, 21:36:03
Post by: axtran on Thu, 22 September 2016, 06:56:23
Post by: redbanshee on Thu, 22 September 2016, 13:24:10
Post by: rainb1ood on Tue, 27 September 2016, 19:58:50
Post by: ryancantkd on Fri, 28 October 2016, 08:47:23
Post by: SparrowHAWX on Sun, 30 October 2016, 14:01:24
Post by: Jokrik on Mon, 07 November 2016, 20:08:05
Post by: autobot on Tue, 15 November 2016, 22:09:45
I'm also interested in getting an Orion V2, how about another group buy??
Me too!
Post by: MrRooks on Mon, 05 December 2016, 10:53:05
Post by: le_wraith on Fri, 06 January 2017, 18:55:58
Just FYI--the A87 spec PCBs fit in the Orion v2 (I built some internals with a steel plate + TX87 PCB. :thumb:
Thanks for the tip. So would this fit? http://www.gonskeyboardworks.com/manuals/131-nerd-pcbs.html
Post by: rabbitfire on Fri, 06 January 2017, 21:04:06
Post by: axtran on Sat, 07 January 2017, 08:50:35
Just FYI--the A87 spec PCBs fit in the Orion v2 (I built some internals with a steel plate + TX87 PCB. :thumb:
Thanks for the tip. So would this fit? http://www.gonskeyboardworks.com/manuals/131-nerd-pcbs.html
Not quite. The spec matches however the spacebar is flipped on the NerD TKL (I'm actually building my Orion v2 with that PCB). You'll have to modify the plate for spacebar Stabilizer clearance. GON has a video of plate modification on his site, too.
Sent from my iPhone using Tapatalk
Post by: E3E on Sat, 07 January 2017, 20:32:44
Just upgraded my Orion's plate to carbon fiber with a special touch. ;D
(http://i.imgur.com/YMKVhWN.jpg)
I have one more plate that I plan on using for my Mira prototype and then the steel plate from the Orion will go into another TKL I build with an Alphas PCB in the future. My two babies with hotswappable PCBs will have the carbon.
Thanks Angelo. :D
Post by: ramnes on Sun, 08 January 2017, 10:05:34
Post by: kacase on Wed, 25 January 2017, 02:55:36
I guess the ones for the front are T10 and for the back T8/9? :-\
My screws show quite a bit of wear, so I want to replace them. :-X
Thanks for your help lads! ;D
Post by: E3E on Wed, 25 January 2017, 03:08:47
Hey Guys, I was planning on replacing the screws for the alu base of my orion v2. Does anyone know which exact ones i need?
I guess the ones for the front are T10 and for the back T8/9? :-\
My screws show quite a bit of wear, so I want to replace them. :-X
Thanks for your help lads! ;D
Are yours torx? I thought they were hex. Hmm, not sure the sizes though. I think the shorter ones are around 6 mm and M3 metric machine screws. I'll have to measure them again though.
Total length on the small ones is 6mm, thread length is 4mm.
On the long ones (for alu and angled bottom), total length is 15mm and the thread length is 12mm. They're M3 screws.
Post by: kacase on Wed, 25 January 2017, 03:21:54
No wonder it is hard to open the case with a torx driver when the screws are hex! I am not sure how I assembled it back then without the right screw driver.
And thank you very much for the size of the small ones!
I will get some V-Shaped 6mm M3 Hex screws for that.
It would be really awesome if you could tell me the size of the back ones as well!
I'm in your debt! :)
Post by: E3E on Wed, 25 January 2017, 11:15:35
They are hex indeed. I feel a bit dumb. :-[
No wonder it is hard to open the case with a torx driver when the screws are hex! I am not sure how I assembled it back then without the right screw driver.
And thank you very much for the size of the small ones!
I will get some V-Shaped 6mm M3 Hex screws for that.
It would be really awesome if you could tell me the size of the back ones as well!
I'm in your debt! :)
It should be 15mm long hex socket cap head M3 screws.
Hope you get what you need! Yeah, some of Duck's boards use torx. I know the Octagon v1 I had did, and I think the Lightpad and Lightsaver as well as Eagle and Viper did as well. Tray cases seemed to have used torx.
Post by: kconfire on Wed, 25 January 2017, 15:07:44
PM me with your offers please :D
Post by: missalaire on Wed, 25 January 2017, 23:51:42
Post by: kacase on Sun, 12 February 2017, 20:37:21
I think I have fried half of my orion :'(
While desoldering the ' switch's sip socket (had to replace the whole switch because it was sticky), I pulled part of the pcbs socket for the sip socket out as well. After installing a brand new switch with sip sockets and soldering it, I noticed that none of the LEDs in the third row, left and including the ' key, were lit up. Also the three left bottom SMD RGB LEDs were malfunctioning. One glimmering and vigorously switching to random colours, the others not lighting up at all. So I guess I have broken half of my orion. Unless you guys have any recommendations on how to fix it.
The typing itself works fine. Its just the lighting that is broken.
Otherwise I would like to maybe get a pcb from someone here who has a spare. I would be really happy to hear from someone!
I ruined my board as well which is why I asked for a pcb and plate :-\
edit: actually I ruined it quite a while back I've just been too embarrassed to mention it :p :p :p
anyways you are having the same problems as everyone who has encountered this issue with flashing rgb leds. It is a design flaw in the pcb. Here is the fix for the rgb led's. I am not sure what is wrong with your led's not turning on. If you can take a photo I can help youShow Image(http://i.imgur.com/ztMk8kh.jpg)
The issue comes from the (+) copper hole on the led. This specific hole is easily prone to damage when desoldered and it stops the flow of current. To repair this issue you need to solder a small wire from the capacitor to the (+) pad, this should fix your issue. The led's not turning on might be the result of another damaged pad. Please take a photo and i can probably lead you to a fix.
special thanks to 02d who gave me this info
Thanks a lot again for your write up appleonama. I didn't get to reopening my Orion until today. But I can now send you pictures from the bottom of it.
I have the problem that my third row (from the bottom) of Leds, so all keys left of the enter button don't light up and that the rgb underlights on the left side do not work/ just flimmers (115,116,117).
The leds stopped working when I resoldered the sticky "]" switch.
In this photo you can see the working enter button on the left and the first button in the third row that does. It work. You can see the awful resoldering job on the right next to it (close to r91)
(http://I.imgur.com/gXVpBcA.jpg)
Is there some connection I can bridge to fix both the third row as well as the under light leds?
(http://I.imgur.com/lwmyvuq.jpg)
Thank you in advance for your help, kacase
Post by: Viking_Robot on Wed, 15 February 2017, 21:13:54
Post by: Viking_Robot on Sun, 26 February 2017, 13:21:12