Really like the look of this. I can't imagine it wouldn't be compatible with ANSI, but either case would need that. Also consider a long acrylic foot like exant, since you're building an acrylic bottom plate anyways. Might be more stable?
F row would make it a 96key, and there's several of those! Very few 78keys.Maybe there's a reason for that ;) Variety is always good though, I guess
I'm very very interested as long as:
It's affordable, I.e. less than $300, preferably around $200 or less.
Edit: Scratch that last part, I looked at it again and I think the first design is better. It's more unique anyway.
For those who suggested a different look to the case, is this an improvement?
(Attachment Link)
For those who suggested a different look to the case, is this an improvement?
(Attachment Link)
Personally, I am not sure I see the point of the 'vanity' base... I for one would never turn my keyboard over to look at that, very much a novelty that would wear off after 5 minutes IMO, but it WOULD make sense to have it diffused for the LED's. Just my opinion anyway.
Personally, I am not sure I see the point of the 'vanity' base... I for one would never turn my keyboard over to look at that, very much a novelty that would wear off after 5 minutes IMO, but it WOULD make sense to have it diffused for the LED's. Just my opinion anyway.
the vanity base is one of the things that makes this most unlike other keyboards.
A glowing board from below is very nice to look at, and it won't blind you because you're typing on top. It's a big difference from all those backlit boards.
But I think we're looking at $500+ prices here, so I'm not following this thread anymore. Unless it winds up being massdropped and massproduced at $150 or less.
But I think we're looking at $500+ prices here, so I'm not following this thread anymore. Unless it winds up being massdropped and massproduced at $150 or less.
Here is a foot design rather than having a standard foot, if there is enough interest in this then I will get a quote from the manufacturer.
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Would it be possible to have a full alu, angled bottom piece instead of the flat acrylic plate with screw in feet?
Other than that I do have to say that I like the design and the layout! :)
Cheers
That looks sick!Would it be possible to have a full alu, angled bottom piece instead of the flat acrylic plate with screw in feet?
Other than that I do have to say that I like the design and the layout! :)
Cheers
Here you go!
(Attachment Link)
(Attachment Link)
(Attachment Link)
I like the new base design, but I don't mind the acrylic either, even with standard screw in feet. I'm strongly leaning towards the fully beveled top though.
Even though I reside in Europe I don't do ISO, this looks very nice though and depending on pricing/time line I'd definitely make an exception and buy one.
Supports ANSI as well
I would prefer not to have screw in feet. An angled case is more aesthetic imo...
-1I would prefer not to have screw in feet. An angled case is more aesthetic imo...
+1
-1I would prefer not to have screw in feet. An angled case is more aesthetic imo...
+1
(I prefer flat cases, which is one of the reasons why I'm interested in in this keyboard.)
Great to see a UK keyboard with numpad - I'd definitely be interested.
I realise it's adding complexity, but could you give some thought to adding a Bluetooth module and battery to make this wireless? To my knowledge, there has never been an wireless ISO mechanical keyboard with a number pad ... ever. Adding that would make this my endgame keyboard. Great job.
If I can help bring this to life, let me know.
Super cool looking case, is there any chance making a 60% case?
Thanks, i think you should make a poll later on for people to voteSuper cool looking case, is there any chance making a 60% case?
Not currently but if there is enough interest I could do a group buy for a 60% case.
What do we get for the 350$?
Case with angled bottom + Plate?
How much is the PCB?
Thanks
What do we get for the 350$?
Case with angled bottom + Plate?
How much is the PCB?
Thanks
Top case, Angled base, switch plate and PCB
The blank pcb is $10 with components being $20-30
There could also be the option of Acrylic small feet for the same cost as the Aluminium ones.
Thoughts?
Any updates? :-X
Pretty hyped for this tbh
Any updates? :-X
Pretty hyped for this tbh
I will have a bigger update when I have quotes back from the PCBA and the case manufacturers. I have received the first prototype PCB samples and currently ensuring that they work correctly and have no flaws that need to be addressed.
For those who suggested a different look to the case, is this an improvement?
(Attachment Link)
Hard to say for sure from the renders but it doesn't look like the plate sports switch top opening. Is this indeed the car or was or just a simplification for the render?The plate will be using the same switch holes as in LZ-GH https://dangwang.files.wordpress.com/2013/06/img_0604.jpg (https://dangwang.files.wordpress.com/2013/06/img_0604.jpg) which support switch top removal.
ETA Of GB?Mid to late June I hope
Here are examples of the green and blue pcb colours, colours apart from green do cost slightly but not significantly more
If we go with acrylic bottom what pcb color are you considering? The tender shows green, but I think that is kind of boring of were going to have a window to view it. Thinking white, blue or red would be better, with white being the best for reflecting led underglow.
I'd go with a white PCB, because if you put LEDs in there, they will reflect better. That said, PCB color is probably at 19 or 20 on my list of important things to consider, so it's NBD.
Colour other than green adds ~$2 to the pcb cost, What would be everyones preference between Green, Red or Blue?I'd go with a white PCB, because if you put LEDs in there, they will reflect better. That said, PCB color is probably at 19 or 20 on my list of important things to consider, so it's NBD.
I'd agree that pcb color isn't a deal breaker, but it is also something that can be easily addressed with almost zero effort and very minimal cost. Seems worthwhile to me to at least get quotes for a color other than green.
Colour other than green adds ~$2 to the pcb cost, What would be everyones preference between Green, Red or Blue?I'd go with a white PCB, because if you put LEDs in there, they will reflect better. That said, PCB color is probably at 19 or 20 on my list of important things to consider, so it's NBD.
I'd agree that pcb color isn't a deal breaker, but it is also something that can be easily addressed with almost zero effort and very minimal cost. Seems worthwhile to me to at least get quotes for a color other than green.
Colour other than green adds ~$2 to the pcb cost, What would be everyones preference between Green, Red or Blue?
I would be interested in like silver or something out of the ordinary. Or matching to the case colors offered.
Definitely down for this, will it be possible to be invoiced in £'s if you're from the UK? Would be nice not to get shafted by the exchange rate/paypal exchange rate for once?
Definitely down for this, will it be possible to be invoiced in £'s if you're from the UK? Would be nice not to get shafted by the exchange rate/paypal exchange rate for once?
That should be no problem, I will make sure that people will get the lowest cost possible.
first time seeing this, looks fantastic
This is exciting! Hope this is a super successful GB.
Is white possible?
Not a fan of powder coating tbh... Will black anod. be an option or just the colors you posted?Is white possible?
It is possible but only through powder coating which I believe costs slightly more, when the orders are open, feel free to see if powder coating can be done if you don't mind the increased cost of ~$10
Not a fan of powder coating tbh... Will black anod. be an option or just the colors you posted?Is white possible?
It is possible but only through powder coating which I believe costs slightly more, when the orders are open, feel free to see if powder coating can be done if you don't mind the increased cost of ~$10
Cheers
Could the PCB be cut down to a 60%? If so, would it fit a standard 60% case?
I think matching the modifiers on Nautilus (Pantone 533 C) is a better idea. The darker color will allow if to work well with other sets like Yuri, etc. Lighter blues limit visual compatibility to my eye.
Could the PCB be cut down to a 60%? If so, would it fit a standard 60% case?
I have added a line and some holes to help guide the cutting of the PCB to fit a 60%, I based the dimensions off of the GH60 so it should fit standard 60% cases
Will there be a limit to the amount of orders available?
#southpawlivesmatter
Hey man I got a quick question, I'm kinda new here and I'm really interested in this case. You say that we will have the option for a fjell style case, that's the one with the chamfer edges correct?
Also if possible to offer the fire orage color to match with the gmk Yuri orange would be an instant buy for me, if thats possible it would be great. If not I saw that you plan to make a dark blue option and it will also look great :) thanks
I think matching the modifiers on Nautilus (Pantone 533 C) is a better idea. The darker color will allow if to work well with other sets like Yuri, etc. Lighter blues limit visual compatibility to my eye.
Good point, I had forgotten Yuri uses dark blue. 533 C it is!
Just to double check, will the resistors, diodes, etc. come presoldered? Back before you got a quote on the PCBs I remember you saying they currently weren't presoldered, but the first comment/post now says they do come presoldered. I'm a total beginner at building keyboards, so a presoldered PCB would be very good for me.
This is looking awesome. Any fuzzy ideas on the final price for a kit with no extras (just the case, plate, and PCB)? How would one go around reprogramming the keyboard?Just updated the first post with pricing information, the keyboard uses QMK for programming.
Case prices are pretty reasonable at the higher moq. Standard case with screw in feet is a good deal at any moq.
Case prices are pretty reasonable at the higher moq. Standard case with screw in feet is a good deal at any moq.
The separated feet are the ones shown in the pictures attached, IMO they are a much better deal unless we hit an MOQ of 50.
This is looking awesome. Any fuzzy ideas on the final price for a kit with no extras (just the case, plate, and PCB)? How would one go around reprogramming the keyboard?Just updated the first post with pricing information, the keyboard uses QMK for programming.
This is looking awesome. Any fuzzy ideas on the final price for a kit with no extras (just the case, plate, and PCB)? How would one go around reprogramming the keyboard?Just updated the first post with pricing information, the keyboard uses QMK for programming.
Many thanks! QMK makes me a happy man. :P
Some clarifications: The renders with a single slope on the bottom represent the 1800-esque case type? Fjell style will have the sloping on all sides as the original Fjell did (and with thicker edges)?
Are the "separate feet" and "fullsize base" whole separate cases or just addons for the 1800 or Fjell-style cases (as in 1800 and Fjell are the top and the feet/base is the bottom)?
You're correct with the cases, 1800 is single slope and Fjell is all sides.
The separate feet are two angled feet that screw into the case and the fullsized base is the same angle as the feet but spans the whole of the case.
You're correct with the cases, 1800 is single slope and Fjell is all sides.
The separate feet are two angled feet that screw into the case and the fullsized base is the same angle as the feet but spans the whole of the case.
I'm still confused on the options. The price listed for fjell is for a top only or top + flat bottom?
Same with three separate feet. Does the $90 include just feet or is it for a flat bottom with removable feet?
Got it. So I would have to buy fjell top, acrylic bottom, and then custom feet if I want them.The acrylic base is 3mm thick and supported by the top case more than most sandwich cases so I don't expect the plastic to crack.
How thick is the acrylic base? If the feet are mounted to it it might flex and/or crack after a few years when the plastic becomes brittle.
Also, does the full size base replace the acrylic or are they just "feet" that happen to cover up all of the acrylic?
Which case are you having a prototype made for? Fjell or 1800?
I assume they won't solder the parts even if you supply them?
If not I like option B but at the same time I was hoping we would hit an MOQ that doesn't really make that option feasible.
How hard is it to solder these parts?
Are they small?
Does the pcb cost increase by two or 3 times or is it 2/3?
I'd be willing to pay $15 more to feet those parts soldered by the mfr.
Hi, just wondering...There is no room to add a split spacebar as the holes go straight through the microcontroller. There is a fullsize right shift option available.
Maybe you could have more pleople interested if:
-You added the split space bar layout like 2.25 + 1 + 2.75 = 6 and 2.75 + 1.5 + 2.75 = 7.
-You added the fullsize right shift.
Good luck.
PS : I just bought an assembled Whitefox + Numpad, so I'm covered.
That and it was a pain to get AZERTY caps, so don't if all ever get another keyboard...
There are other manufacturers available that wouldn't lead to a price increase. Where are you looking for your source?
There are other manufacturers available that wouldn't lead to a price increase. Where are you looking for your source?
I am getting quotes from PCBWay, Elecrow and PCBcart currently, if you know of any others then I would appreciate the help.
OSHPark would cost near $100 for just the board without assembly they are only for small prototypes.There are other manufacturers available that wouldn't lead to a price increase. Where are you looking for your source?
I am getting quotes from PCBWay, Elecrow and PCBcart currently, if you know of any others then I would appreciate the help.
I have a friend whove always spoken well about OSHPark, but they seem to be more for prototype boards looking at their homepage (which doesn't mention SMD soldering either...)
There are other manufacturers available that wouldn't lead to a price increase. Where are you looking for your source?
I am getting quotes from PCBWay, Elecrow and PCBcart currently, if you know of any others then I would appreciate the help.
Any idea when this might go live? Roughly :P
Any idea when this might go live? Roughly :P
Mid to end of next month.
Came here from RSII rev. D reddit.
I'll just forget that crappy thing and opt for this state-of-the-art beauty.
BTW, will it be possible to get PCB only in case I mill my own case and plate?
Very interesting board.
If I'm reading this right the aluminum full base is optional?
I can use the top piece solely with the acrylic base?
...if so, can we purchase multiple diffusers? at 6$ I might want more than one in case of cracks etc.
If I can purchase spare PCBs and acrylic plates I might need this to pair with my Fjell :-X
Invoices will be sent out after the Groupbuy ends, PM me to discuss specifics if you cannot meet the deadlines.Any idea when this might go live? Roughly :P
Mid to end of next month.
please do end of next month... cuz payday or my wallet can't take it ;)
Invoices will be sent out after the Groupbuy ends, PM me to discuss specifics if you cannot meet the deadlines.Any idea when this might go live? Roughly :P
Mid to end of next month.
please do end of next month... cuz payday or my wallet can't take it ;)
Very interesting board.
If I'm reading this right the aluminum full base is optional?
I can use the top piece solely with the acrylic base?
...if so, can we purchase multiple diffusers? at 6$ I might want more than one in case of cracks etc.
If I can purchase spare PCBs and acrylic plates I might need this to pair with my Fjell :-X
That would be no problem. I will have an option for ordering multiple pieces on the form.
overall looks pretty good. I think the feet could use some insets for where the non-slip pads go though.
Does the top case include the acrylic vanity base? Or will we have to get the fullsize base as well?
You can set it up like this:
Either top case
Acrylic bottom or full aluminum bottom
If you go acrylic, you can use the angled feet or universal round screw in feet
Correct!You can set it up like this:
Either top case
Acrylic bottom or full aluminum bottom
If you go acrylic, you can use the angled feet or universal round screw in feet
The full aluminium bottom is the big slanted one right?
I agree with Traveler also. I like the UK78 logo. The subtle engraving would work even on darker color case.I will look into if this is possible! I will also see if cutouts for the bumpons can be put on the feet.
Do you plan on getting a fjell style sample?
Any sample anodized chips for all the colors coming before order?
How good is this ?I'd wait for the UK78, but if you're wanting a cheaper option and live in the US then it's worth considering
https://www.massdrop.com/buy/red-scarf-ii-plus-ver-d-custom-mechanical-keyboard-kit
Everything still on track for the GB to launch later this month?
Definitely excited to get my hands on this
How much would international shipping cost?
I am very interesed. The only thing that I am worrying about is how much will it cost to ship out to China.
What about sending PCB only to Russia? According to Royal Mail it's something about 10 GBP for international tracked. Can you confirm that?
This looks pretty much like my endgame board! Don't know why it took so long for me to see this thread, now I need to find the money for when the GB goes live! :'(Would make a good match for hyperfuse :)
Also if only there was a purple case option, that would be my perfect board!
This looks pretty much like my endgame board! Don't know why it took so long for me to see this thread, now I need to find the money for when the GB goes live! :'(
Also if only there was a purple case option, that would be my perfect board!
Wait, orders are accepted already?!
Wait, orders are accepted already?!The Group Buy opens 18:00 GMT+1 18th June if everything goes according to plan Check the GB thread for updates https://geekhack.org/index.php?topic=90060.0
Sample Case photos:
A few points following inspection of the sample, the manufacturer was close to the colour I specified for anodising however I chose the wrong colour to match N9, the new colour will be Pantone 446 C.
The lasered UK78 logo will not be on production cases as it doesn't suit darker coloured cases.
The only manufacturing error on the case was a scratch made by the anodising wire but it is on the inside edge hidden by the feet from view completely.
Also those are not the bumpons that will come with the case, just ones I had lying around.
(Attachment Link) (Attachment Link)
(Attachment Link) (Attachment Link)
(Attachment Link) (Attachment Link)
Sample Case photos:
A few points following inspection of the sample, the manufacturer was close to the colour I specified for anodising however I chose the wrong colour to match N9, the new colour will be Pantone 446 C.
The lasered UK78 logo will not be on production cases as it doesn't suit darker coloured cases.
The only manufacturing error on the case was a scratch made by the anodising wire but it is on the inside edge hidden by the feet from view completely.
Also those are not the bumpons that will come with the case, just ones I had lying around.
(Attachment Link) (Attachment Link)
(Attachment Link) (Attachment Link)
(Attachment Link) (Attachment Link)
I'm a little confused on the base and wanted to clarify before joining tomorrow! In the prototypes the acrylic base reached all round the aluminum case. But for the 1800 case does the base just to cover the PCB? Do these pictures even have a base? Or will the base actually add some more height to the board? Are there any pictures with the case and the acrylic base? Sorry for all the questions! Excited for this to go live!
Sent from my iPhone using Tapatalk
Sample Case photos:
A few points following inspection of the sample, the manufacturer was close to the colour I specified for anodising however I chose the wrong colour to match N9, the new colour will be Pantone 446 C.
The lasered UK78 logo will not be on production cases as it doesn't suit darker coloured cases.
The only manufacturing error on the case was a scratch made by the anodising wire but it is on the inside edge hidden by the feet from view completely.
Also those are not the bumpons that will come with the case, just ones I had lying around.
(Attachment Link) (Attachment Link)
(Attachment Link) (Attachment Link)
(Attachment Link) (Attachment Link)
I'm a little confused on the base and wanted to clarify before joining tomorrow! In the prototypes the acrylic base reached all round the aluminum case. But for the 1800 case does the base just to cover the PCB? Do these pictures even have a base? Or will the base actually add some more height to the board? Are there any pictures with the case and the acrylic base? Sorry for all the questions! Excited for this to go live!
Sent from my iPhone using Tapatalk
The photos don't show the acrylic base, it would be sandwiched between the feet and the top case adding 3mm to the height compared to without. I've attached a render showing the case with acrylic base/diffuser added.
Group Buy now live apologies for the delay https://geekhack.org/index.php?topic=90060.0