Recent Posts

Pages:  [1] 2 3 4 5 6 ... 10 »
1
geekhack Media / Re: Post Your Booper Keycaps!
« Last post by shinz0 on Sat, 21 April 2018, 12:39:37 »
2
geekhack Media / Re: Post your Nightcaps!
« Last post by BestShuckleNA on Sat, 21 April 2018, 12:38:09 »
Cant wait until I get a new phone then I'll start posting in here more, here's a little potato for now tho

Sent from my LG-H812 using Tapatalk

3
Group Buys and Preorders / Re: Rama Works M60-A
« Last post by xondat on Sat, 21 April 2018, 12:37:59 »
Is the PCB hot swappable? Thank you!

Yes, it uses Kailh sockets.

m60-a is going to be my first mech kb, would those kailh sockets work with Zealios?

Yes, anything Cherry MX style, so Cherry/Gateron (Zealio)/Kailh (Box)/etc.
4
Group Buys and Preorders / Re: Rama Works M60-A
« Last post by forstsiven on Sat, 21 April 2018, 12:35:44 »
Is the PCB hot swappable? Thank you!

Yes, it uses Kailh sockets.

m60-a is going to be my first mech kb, would those kailh sockets work with Zealios?
5
Group Buys and Preorders / Re: [GB] GMK Olivia
« Last post by scud80 on Sat, 21 April 2018, 12:34:13 »
hadn't heard of that ... thx.  though it looks like it's split, and i use ortho now.  guess i have some research to do.
6
i emailed kono a week or so ago and he said he thought he might have a few, but wasn't sure.  and picking up from r/mm is fine, i just prefer not to pay the flip tax when possible.
7
Anyway, whoever that's #69 please swap with me thanks.
8
Ok, have my board built, but the software won't recognize it - something about DFU not found? Anyone know what I'm screwing up?

Do you have atmel flip installed?  Do you have the newest version of O2D?  You also need to hold a key while plugging the board in to get it into DFU mode.  Normally ESC or Caps Lock.

I have Flip installed, holding Esc and Caps Lock both didn't work for getting it into DFU mode.

Hold down the topmost key above the arrow keys as shown here for like 2 seconds while plugging the board in:
(Attachment Link)

Thanks! I think that put it into bootloader mode (none of the layer LEDs lit up), but I still get a DFU programmer not found error even with it in bootloader mode. I have Flip installed, do I need to do anything else with it? My O2D keymapper version is 1.12.675 if that matters also.

Have you installed the proper drivers for the board? In device manager, when you enter bootloader mode, you should see a device show up as Atmega32U4 if you have the proper driver installed. For more detailed instructions, I'll link the page I used to make sense of this process:
http://kbdlab.co.kr/index.php?document_srl=364613&mid=board_sw
Just be sure to translate the page ;)

Thanks so much! That guide got me up and running. Really appreciate the help. :)
9
this GB happened before i got my first mech.  do they only make the number of sets ordered or are there any extras so that i'd be able to buy one?  this is probably my favorite GMK set that i've seen so far.

depends on the GB, some will have extras, some won't

i don't know for sure about this one

people will always sell aftermarket on /r/mechmarket though

Looks like Kono updated the price on their store to $199, so I'm guessing they'll have extra available at that price.
10
Interest Checks / Re: [IC] Glow SA, Glow-in-the-Dark profiled SA
« Last post by scud80 on Sat, 21 April 2018, 12:25:52 »
after seeing the dsa borealis example, i rescind my contrast request.  missed the dye sub part in the OP ... why dye sub?  just for price?
Pages:  [1] 2 3 4 5 6 ... 10 »