Author Topic: [GB] Artisan Case v1 - Complete (Read 26348 times)

hayt · « **on:** Tue, 08 May 2018, 21:57:34 »

~~Group Buy Form~~

# Shipped: 50/50

5x7 (35 Slots) - Premium Artisan Storage Case

1" Machined Acrylic w/ Bead Blasted Finish
1/4" Acrylic Laser Cut Lid
1/4" Rubber Bumpers x 4
Nylatron Thumb Screws x 2
1/2" Charcoal Travel Foam
Timestamp Ring
Custom packaging

Cell Dimensions (LxWxH): 0.83" x .0.83" x 0.81"
Cell Wall Height: 0.25"

Lead Time: 8-9 weeks

Limited to 50 units (1 per person)

Made in the USA

$97 + Shipping

Additional Pics

Interest Check Thread

Thanks for your interest! I'll leave the form open for a few days and will RNG for the 50 slots.

hayt

iamtootallforthis · « **Reply #1 on:** Tue, 08 May 2018, 22:08:14 »

Approved.

Caveat Emptor

AuthenticDanger · « **Reply #2 on:** Tue, 08 May 2018, 22:15:10 »

So tempting....

P1kas · « **Reply #3 on:** Tue, 08 May 2018, 22:15:51 »

How long will the form be open?

Dennyroxsox · « **Reply #4 on:** Tue, 08 May 2018, 22:16:12 »

My man! Good luck with the GB! Pumped for this!

iamtootallforthis · « **Reply #5 on:** Tue, 08 May 2018, 22:16:38 »

Quote from: P1kas on Tue, 08 May 2018, 22:15:51

How long will the form be open?

It says a few days in the OP

OneNightFriend · « **Reply #6 on:** Tue, 08 May 2018, 22:20:55 »

Najs case hayt, I'm in :pray:

SeedyOne · « **Reply #7 on:** Tue, 08 May 2018, 22:25:51 »

Looks so good!

romevi · « **Reply #8 on:** Tue, 08 May 2018, 22:43:00 »

How the turntables...

dblack · « **Reply #9 on:** Tue, 08 May 2018, 22:54:30 »

seems nice than my ziplock bag. good going greg.

Sissy · « **Reply #10 on:** Tue, 08 May 2018, 22:55:01 »

Finally a replacement for my TCG deck box I store everything in.

MythicalWagyu · « **Reply #11 on:** Tue, 08 May 2018, 23:09:41 »

Beautiful work man, GLWGB! I'm sure these will be gone in short order.

kconfire · « **Reply #12 on:** Wed, 09 May 2018, 00:19:30 »

Submitted.

foxmancore · « **Reply #13 on:** Wed, 09 May 2018, 01:16:30 »

submitted

funderburker · « **Reply #14 on:** Wed, 09 May 2018, 04:20:34 »

Beautiful! Good luck with the GB. Don't have that much artisans to justify this but this is definitely a must-have for collectors.

dgneo · « **Reply #15 on:** Wed, 09 May 2018, 06:46:36 »

godinjointform · « **Reply #16 on:** Wed, 09 May 2018, 08:22:08 »

looks good, I'm in

afrokobe · « **Reply #17 on:** Wed, 09 May 2018, 08:50:02 »

can i get a version without screws, preferably with magnets?

roostrc0gburn · « **Reply #18 on:** Wed, 09 May 2018, 11:11:19 »

do want. thanks Hayt!

AuthenticDanger · « **Reply #19 on:** Wed, 09 May 2018, 11:22:32 »

Quote from: afrokobe on Wed, 09 May 2018, 08:50:02

can i get a version without screws, preferably with magnets?

Just replace the screws with magnets if you win one.

KetchyKech · « **Reply #20 on:** Wed, 09 May 2018, 11:50:31 »

In.

hayt · « **Reply #21 on:** Wed, 09 May 2018, 16:52:08 »

Thanks, everyone for the interest and enthusiasm! I'll probably close the form on Friday and will then start sending invoices.

Quote from: afrokobe on Wed, 09 May 2018, 08:50:02

can i get a version without screws, preferably with magnets?

Nah bruh, you can get velcro tho

Quote from: ZuXzu on Tue, 08 May 2018, 22:54:30

seems nice than my ziplock bag. good going greg.

Thanks daniel

dblack · « **Reply #22 on:** Wed, 09 May 2018, 18:39:25 »

Quote from: haytorious on Wed, 09 May 2018, 16:52:08

Thanks, everyone for the interest and enthusiasm! I'll probably close the form on Friday and will then start sending invoices.

Quote from: afrokobe on Wed, 09 May 2018, 08:50:02
can i get a version without screws, preferably with magnets?

Nah bruh, you can get velcro tho

Quote from: ZuXzu on Tue, 08 May 2018, 22:54:30
seems nice than my ziplock bag. good going greg.

Thanks daniel

Seriously though, it displays your talent for design. Seriously considering dropping the cash.

hayt · « **Reply #23 on:** Fri, 11 May 2018, 08:19:23 »

Form closed, I'll start sending out invoices this evening when I get home from work.

Thanks everyone for your interest!!

Cocopah · « **Reply #24 on:** Fri, 11 May 2018, 16:04:32 »

:crossed_fingers:

romevi · « **Reply #25 on:** Fri, 11 May 2018, 16:10:31 »

:crossed_eyes:

AuthenticDanger · « **Reply #26 on:** Fri, 11 May 2018, 17:37:30 »

Quote from: haytorious on Fri, 11 May 2018, 08:19:23

Form closed, I'll start sending out invoices this evening when I get home from work.

Thanks everyone for your interest!!

What kind of odds are we looking at? 25%? Worse?

hayt · « **Reply #27 on:** Fri, 11 May 2018, 19:53:39 »

Invoices sent

If we can gather funds over the weekend, I'd love to pull the trigger on the machine order on Monday or Tuesday.

Will also be sure to keep this thread updated with production happenings!!

Thx,
hayt

OneNightFriend · « **Reply #28 on:** Fri, 11 May 2018, 20:07:04 »

At least I got one invoice today! Paid up and looking forward to it hayt

Quote from: haytorious on Fri, 11 May 2018, 19:53:39

Invoices sent

If we can gather funds over the weekend, I'd love to pull the trigger on the machine order on Monday or Tuesday.

Will also be sure to keep this thread updated with production happenings!!

Thx,
hayt

romevi · « **Reply #29 on:** Fri, 11 May 2018, 20:28:51 »

Super gelatinous of the winners. Congrats all!

foxmancore · « **Reply #30 on:** Fri, 11 May 2018, 22:25:15 »

Rip didn't get an invoice

P1kas · « **Reply #31 on:** Sun, 13 May 2018, 00:03:03 »

💸💸💸💸💸💸💸

hayt · « **Reply #32 on:** Wed, 16 May 2018, 19:39:47 »

Quick update: thank you, everyone, for completing the invoices! I've submitted the production order to the machine shop on Monday, and they are quoting me for an early June delivery to the bead blasting shop in ATL. With any luck, we may be able to start shipping these out in mid-June. More to follow. GH

LightningXI · « **Reply #33 on:** Wed, 16 May 2018, 23:33:36 »

Quote from: haytorious on Wed, 16 May 2018, 19:39:47

Quick update: thank you, everyone, for completing the invoices! I've submitted the production order to the machine shop on Monday, and they are quoting me for an early June delivery to the bead blasting shop in ATL. With any luck, we may be able to start shipping these out in mid-June. More to follow. GH

Very exciting! I'd appreciate a shipping info confirmation before shipment as I expect to move in mid June. I would be wary of USPS forwarding to be honest. Please do add a note to my order!

Sent from my mobile using Tapatalk

romevi · « **Reply #34 on:** Wed, 16 May 2018, 23:33:44 »

Quote from: haytorious on Wed, 16 May 2018, 19:39:47

Quick update: thank you, everyone, for completing the invoices! I've submitted the production order to the machine shop on Monday, and they are quoting me for an early June delivery to the bead blasting shop in ATL. With any luck, we may be able to start shipping these out in mid-June. More to follow. GH

hayt · « **Reply #35 on:** Thu, 17 May 2018, 08:23:05 »

Quote from: LightningXI on Wed, 16 May 2018, 23:33:36

Quote from: haytorious on Wed, 16 May 2018, 19:39:47
Quick update: thank you, everyone, for completing the invoices! I've submitted the production order to the machine shop on Monday, and they are quoting me for an early June delivery to the bead blasting shop in ATL. With any luck, we may be able to start shipping these out in mid-June. More to follow. GH
Very exciting! I'd appreciate a shipping info confirmation before shipment as I expect to move in mid June. I would be wary of USPS forwarding to be honest. Please do add a note to my order!

Sent from my mobile using Tapatalk

Noted, no problem. Will follow up with you when ready to ship

hayt · « **Reply #36 on:** Tue, 29 May 2018, 09:52:12 »

Lids are in from laser cutting. I will leave the paper film on the lids when shipping out to avoid any scratches and for that nice peel.

Machined case bottoms should be arriving at the bead-blaster here in ATL within the next couple weeks, more to follow.

roostrc0gburn · « **Reply #37 on:** Tue, 29 May 2018, 15:24:39 »

Quote from: haytorious on Tue, 29 May 2018, 09:52:12

Lids are in from laser cutting. I will leave the paper film on the lids when shipping out to avoid any scratches and for that nice peel.

Machined case bottoms should be arriving at the bead-blaster here in ATL within the next couple weeks, more to follow.

(Attachment Link)

great news! thanks for the update, haytorious

quadfreak · « **Reply #38 on:** Tue, 29 May 2018, 21:51:27 »

Dank. Can't wait for this.

Dennyroxsox · « **Reply #39 on:** Tue, 29 May 2018, 21:54:11 »

Quote from: haytorious on Tue, 29 May 2018, 09:52:12

Lids are in from laser cutting. I will leave the paper film on the lids when shipping out to avoid any scratches and for that nice peel.

I'm ready for that sweet peel feel!

aya3154 · « **Reply #40 on:** Thu, 31 May 2018, 01:38:49 »

So bummed I arrived late to this beautiful party

Any chances of round 2?

hayt · « **Reply #41 on:** Thu, 31 May 2018, 15:17:25 »

Quote from: aya3154 on Thu, 31 May 2018, 01:38:49

So bummed I arrived late to this beautiful party

Any chances of round 2?

Maybe! Not really sure yet, I would really prefer to find an outsource to Asia for a larger QTY production run, if there is a demand for it. Also a potential for a very small run of 9x12 (108 slot) case.

Going through all the nylon bolts, as they have a bit of extra nylon thread here and there that I either clipped or shaved off. I imagine over time, the nylon heads will smooth out nicely.

hayt · « **Reply #42 on:** Thu, 07 June 2018, 09:27:30 »

Hi All, quick update. The production machined cases have arrived in good order. After a quick inspection of a few of the cases, everything is looking good.

I'll be dropping these off at the bead blasting shop tomorrow, hoping to have them ready for pick-up mid-next week. More to follow.

romevi · « **Reply #43 on:** Thu, 07 June 2018, 09:34:31 »

Quote from: haytorious on Thu, 07 June 2018, 09:27:30

bead blasting

Hongook · « **Reply #44 on:** Thu, 07 June 2018, 09:35:44 »

I'll also express my interest in hoping for a round two. Case looks great!

MajorclaM · « **Reply #45 on:** Thu, 07 June 2018, 15:55:13 »

How much savings do you think a round 2 produced overseas would have. I really like the screws and other features this case has over the evil box or even my crappy tackle box case.

hayt · « **Reply #46 on:** Thu, 07 June 2018, 17:04:50 »

Quote from: MajorclaM on Thu, 07 June 2018, 15:55:13

How much savings do you think a round 2 produced overseas would have. I really like the screws and other features this case has over the evil box or even my crappy tackle box case.

Great question man!

Once we are through with this group buy I will do a deep dive into outsourcing overseas. I need to determine how much cost I can shave off, reduce the retail price, and hopefully garner a larger amount of interest to get a good run size going. More to follow for sure!

meepmeep · « **Reply #47 on:** Thu, 07 June 2018, 17:27:30 »

These are awesome, are you ever making any more of them?

nxtruong · « **Reply #48 on:** Fri, 08 June 2018, 10:08:39 »

Quote from: meepmeep on Thu, 07 June 2018, 17:27:30

These are awesome, are you ever making any more of them?

+1

I need some as well!

jackedhardwarejunkie · « **Reply #49 on:** Fri, 08 June 2018, 10:18:11 »

No lie I'm sad I sat out on this one as well, still followed the thread but I was all like ahhh well I got the evil box an the ano'd alu box... The more I see this one the more I absolutely need it

.. Beautiful design Hayt. keep it up! (Make a keyset one too if you manage to source thru cn)

hayt · « **Reply #50 on:** Fri, 08 June 2018, 15:19:53 »

Quote from: jackedhardwarejunkie on Fri, 08 June 2018, 10:18:11

No lie I'm sad I sat out on this one as well, still followed the thread but I was all like ahhh well I got the evil box an the ano'd alu box... The more I see this one the more I absolutely need it .. Beautiful design Hayt. keep it up! (Make a keyset one too if you manage to source thru cn)

Thanks, man. Appreciate the kind words

Quote from: meepmeep on Thu, 07 June 2018, 17:27:30

These are awesome, are you ever making any more of them?

Yes, once this GB is finished and I can garner some feedback from the community, I will work to conduct a larger scale second run.

By way of an update, I picked up the test sample from the bead blasting shop today, and happy to say that the cloudy finish looks great. The rest of the batch will be ready for pick-up in a weeks time, so I anticipate next weekend I will be busy wrapping up and preparing for shipping. More to come.

OneNightFriend · « **Reply #51 on:** Fri, 08 June 2018, 15:30:05 »

Awesome, thanks for the update hayt!

Skaazi · « **Reply #52 on:** Fri, 08 June 2018, 15:54:34 »

Looking good. I'd be interested in the second run.

aya3154 · « **Reply #53 on:** Fri, 08 June 2018, 15:57:33 »

looks very clean

nimblejacks · « **Reply #54 on:** Sat, 09 June 2018, 08:06:54 »

Case looks great, might need to jump in on the second run.

Sissy · « **Reply #55 on:** Mon, 11 June 2018, 08:57:41 »

I cant wait to fill mine with dead flies I find on my window.

Astrasa · « **Reply #56 on:** Mon, 11 June 2018, 13:19:38 »

Thanks for the update, can't wait til they ship!

aznriptide859 · « **Reply #57 on:** Tue, 12 June 2018, 21:49:23 »

Hi, would there happen to be any extras? Kind of regret not joining

hayt · « **Reply #58 on:** Sat, 16 June 2018, 11:31:20 »

Hi All, quick update. I have received the parts back from bead blasting and am proceeding with packing and preparing for shipment.

A few notes on the parts received:

1) Out of the 50 cases ordered, I have identified 10 that I find have unacceptable machining defects from the manufacturer. These include sizeable chips in the perimeter of the case, cracked bottom, and chipped internal partitions. I have a note out to the machine shop and will await their direction for either replacing or refunding these defective parts.

2) Of the 40 that are in good shape, I will begin shipping these out this week. I will go by invoice order for shipping.

3) If you are in the tail end of the invoices (40-50), we will have to sit tight and wait to hear back from the manufacturer.

4) There is some slight variation in the thread tolerances on the nylon thumb screws. If you receive a case with a tight thumb screw, it will loosen over time with a bit of use. Some of the later cases may ship with an alternative steel threaded bolt (plastic head).

I appreciate everyone's continued support. If you have any questions feel free to contact me directly on Discord or Slack. More to follow

Sissy · « **Reply #59 on:** Sat, 16 June 2018, 21:18:29 »

Thanks for the update, this has gone super fast as is.

LightningXI · « **Reply #60 on:** Sat, 16 June 2018, 21:24:04 »

Quote from: hayt on Sat, 16 June 2018, 11:31:20

Hi All, quick update. I have received the parts back from bead blasting and am proceeding with packing and preparing for shipment.

A few notes on the parts received:

1) Out of the 50 cases ordered, I have identified 10 that I find have unacceptable machining defects from the manufacturer. These include sizeable chips in the perimeter of the case, cracked bottom, and chipped internal partitions. I have a note out to the machine shop and will await their direction for either replacing or refunding these defective parts.

2) Of the 40 that are in good shape, I will begin shipping these out this week. I will go by invoice order for shipping.

3) If you are in the tail end of the invoices (40-50), we will have to sit tight and wait to hear back from the manufacturer.

4) There is some slight variation in the thread tolerances on the nylon thumb screws. If you receive a case with a tight thumb screw, it will loosen over time with a bit of use. Some of the later cases may ship with an alternative steel threaded bolt (plastic head).

I appreciate everyone's continued support. If you have any questions feel free to contact me directly on Discord or Slack. More to follow

(Attachment Link)

Ah bummer, it seems I will have to wait for the manufacturer update. Thanks for the GB update! It's been a smooth ride thus far nonetheless.

Sent from my mobile using Tapatalk

OneNightFriend · « **Reply #61 on:** Sat, 16 June 2018, 21:28:21 »

Quote from: hayt on Sat, 16 June 2018, 11:31:20

Hi All, quick update. I have received the parts back from bead blasting and am proceeding with packing and preparing for shipment.

A few notes on the parts received:

1) Out of the 50 cases ordered, I have identified 10 that I find have unacceptable machining defects from the manufacturer. These include sizeable chips in the perimeter of the case, cracked bottom, and chipped internal partitions. I have a note out to the machine shop and will await their direction for either replacing or refunding these defective parts.

2) Of the 40 that are in good shape, I will begin shipping these out this week. I will go by invoice order for shipping.

3) If you are in the tail end of the invoices (40-50), we will have to sit tight and wait to hear back from the manufacturer.

4) There is some slight variation in the thread tolerances on the nylon thumb screws. If you receive a case with a tight thumb screw, it will loosen over time with a bit of use. Some of the later cases may ship with an alternative steel threaded bolt (plastic head).

I appreciate everyone's continued support. If you have any questions feel free to contact me directly on Discord or Slack. More to follow

(Attachment Link)

Thanks for the great communication so far hayt. Looking forward to getting this case!

hayt · « **Reply #62 on:** Tue, 19 June 2018, 09:14:13 »

Hi All,

Three quick updates:

1) The first 27 cases have been dropped off for shipping today

2) I plan on dropping off the next 14 cases on Thursday, some of these will have steel threaded thumb screws in place of the originally specced nylon screws.

3) The remaining 9 defective cases have been shipped back to the manufacture and awaiting their inspection and feedback. More to come.

Thx,
hayt

AuthenticDanger · « **Reply #63 on:** Tue, 19 June 2018, 14:47:35 »

Are our invoice numbers also our case number or did you assign slots based on something else like when the invoice was paid?

hayt · « **Reply #64 on:** Tue, 19 June 2018, 15:09:16 »

Quote from: AuthenticDanger on Tue, 19 June 2018, 14:47:35

Are our invoice numbers also our case number or did you assign slots based on something else like when the invoice was paid?

Invoice #36 aligns w case # 42, through invoice #45 aligning with # 50. This was done due to a few early supporters who bought more than one case.

AuthenticDanger · « **Reply #65 on:** Tue, 19 June 2018, 15:11:52 »

Ah perfect. Thanks for the info!

P1kas · « **Reply #66 on:** Wed, 20 June 2018, 14:55:36 »

Let's hope the manufacturer is willing to replace them.

hayt · « **Reply #67 on:** Thu, 21 June 2018, 10:45:55 »

# Shipped: 43/50

7 more to go! The defective cases have been returned to the machine shop, delivered today. More to follow on their feedback.

OneNightFriend · « **Reply #68 on:** Thu, 21 June 2018, 14:51:50 »

Got mine in today! Please accept this potato as proof. The threads are definitely tight but overall a beautiful case. The fit of the lid to the case is so perfect!

Dennyroxsox · « **Reply #69 on:** Thu, 21 June 2018, 19:24:36 »

I got mine in today. I love it! Thanks Hayt!

+1 for round 2

nmur · « **Reply #70 on:** Thu, 21 June 2018, 19:57:34 »

nice one boys, looking good

I think I'm in the defective batch group, can't wait to get it tho

Sent from my ONEPLUS A5000 using Tapatalk

Sneaky Potato · « **Reply #71 on:** Thu, 21 June 2018, 21:05:11 »

I’ll post pictures shortly, but the quality of the case is excellent. It was packaged really well, and felt super secure. The quality is leagues above any other acrylic case I’ve seen so far.

Sissy · « **Reply #72 on:** Fri, 22 June 2018, 01:06:17 »

Quote from: nmur on Thu, 21 June 2018, 19:57:34

nice one boys, looking good

I think I'm in the defective batch group, can't wait to get it tho

Sent from my ONEPLUS A5000 using Tapatalk

Real Discrimination against Australians happening here...

hayt · « **Reply #73 on:** Wed, 27 June 2018, 10:03:36 »

Hi All,

To the remaining 7 still awaiting their cases, I have received confirmation that a remake has been issued by the machine shop. I will update with timing as soon as I know more. Sorry for the inconvenience + extended lead time <3

More to follow,

hayt

nmur · « **Reply #74 on:** Wed, 27 June 2018, 10:42:23 »

Quote from: hayt on Wed, 27 June 2018, 10:03:36

Hi All,

To the remaining 7 still awaiting their cases, I have received confirmation that a remake has been issued by the machine shop. I will update with timing as soon as I know more. Sorry for the inconvenience + extended lead time <3

More to follow,

hayt

nice!

thanks

AuthenticDanger · « **Reply #75 on:** Wed, 27 June 2018, 11:05:29 »

I took some photos of my unboxing and the case in action.

All the photos below the fold.

More

The quality is top notch and I'm really happy about the travel foam. Looking forward to bringing it to the next meetup!

hayt · « **Reply #76 on:** Fri, 29 June 2018, 09:26:27 »

For anyone taking their cases to the upcoming meetups, don't forget to use the travel foam!

Also, if you have any feedback on ways to improve the design for travel purposes, please don't hesitate to share!

Thanks,

Hayt

hayt · « **Reply #77 on:** Fri, 29 June 2018, 10:51:32 »

One more update, the machine shop is aiming to send the replacement cases out by mid-July. Add on a week for bead blasting, let's say we can get out the replacements by end of July! Thx GH

P1kas · « **Reply #78 on:** Fri, 29 June 2018, 12:52:15 »

😴 😴 😴

jackedhardwarejunkie · « **Reply #79 on:** Fri, 29 June 2018, 13:01:45 »

Quote from: hayt on Fri, 29 June 2018, 09:26:27

For anyone taking their cases to the upcoming meetups, don't forget to use the travel foam!

Also, if you have any feedback on ways to improve the design for travel purposes, please don't hesitate to share!

Thanks,

Hayt

The only thing I could think for improving the design for travel purposes would be to make the bottom be able to click some switches in then the artisans would be stuck in place vs free to bounce around the case if they're smaller artisans.. but this would mean a bigger case overall...

OneNightFriend · « **Reply #80 on:** Fri, 29 June 2018, 13:27:44 »

An idea I had for V2 was to increase stackability by making a cutout on the bottom for where the screws from the top of another case would go, but enjoying the case so far!

stillzman · « **Reply #81 on:** Sun, 01 July 2018, 13:30:18 »

Got mine, absolutely love it, great quality! The only thing I'm a bit worried about is somehow stripping the threads with the screw but I'm sure as long as I'm careful that wont happen.

oscdawg · « **Reply #82 on:** Mon, 09 July 2018, 21:44:58 »

Also patiently awaiting a round 2. Kicking myself for sleeping on this case

Sent from my Pixel XL using Tapatalk

jackedhardwarejunkie · « **Reply #83 on:** Mon, 09 July 2018, 21:45:38 »

X3... lol

hayt · « **Reply #84 on:** Fri, 13 July 2018, 23:33:25 »

Quick update, I have received confirmation that the replacement parts have shipped. Once they arrive next week I'll do a quick QC and turn them over to the local bead blaster. Granted everything goes well I'd love to have the remaining (7) cases shipped within 2 weeks. Thanks, GH

papa · « **Reply #85 on:** Sat, 14 July 2018, 00:04:23 »

Quote from: hayt on Sat, 16 June 2018, 11:31:20

Hi All, quick update. I have received the parts back from bead blasting and am proceeding with packing and preparing for shipment.

A few notes on the parts received:

1) Out of the 50 cases ordered, I have identified 10 that I find have unacceptable machining defects from the manufacturer. These include sizeable chips in the perimeter of the case, cracked bottom, and chipped internal partitions. I have a note out to the machine shop and will await their direction for either replacing or refunding these defective parts.

2) Of the 40 that are in good shape, I will begin shipping these out this week. I will go by invoice order for shipping.

3) If you are in the tail end of the invoices (40-50), we will have to sit tight and wait to hear back from the manufacturer.

4) There is some slight variation in the thread tolerances on the nylon thumb screws. If you receive a case with a tight thumb screw, it will loosen over time with a bit of use. Some of the later cases may ship with an alternative steel threaded bolt (plastic head).

I appreciate everyone's continued support. If you have any questions feel free to contact me directly on Discord or Slack. More to follow

(Attachment Link)

Looks so good .Nice job

hayt · « **Reply #86 on:** Wed, 18 July 2018, 22:37:35 »

Hiya, quick update. I received the replacement cases, inspected, and have dropped them off today at the local bead blasting shop.

The shop is a little more backed up than they were earlier in the summer, they are quoting me ~2-weeks out before they'll be ready for pickup. If everything goes as planned I would like to have the final 7 shipped out by the end of week 7/30.

There may also be a few leftovers available (not many, like 5 or 6). After all of the GB cases have shipped I'll RNG off the remaining few in this thread.

Thanks all for your patience! GH

widdlekitty · « **Reply #87 on:** Thu, 19 July 2018, 23:33:09 »

hooray! thank you for the timely updates.

Rubbermilitia · « **Reply #88 on:** Sat, 21 July 2018, 01:50:05 »

Ah that is a sexy case

Arcsxum · « **Reply #89 on:** Sun, 22 July 2018, 12:36:10 »

Damn, can't believe I missed such an amazing artisan case.
Really hoping for that r2!!!!!

jackedhardwarejunkie · « **Reply #90 on:** Sun, 22 July 2018, 12:38:01 »

Watching closely for those xtraz

Lormania · « **Reply #91 on:** Tue, 31 July 2018, 00:24:30 »

Hoping for one of the extras!

hayt · « **Reply #92 on:** Tue, 31 July 2018, 11:46:35 »

Quick update, I will be picking up the cases from blasting tomorrow afternoon, and as long as they all look good, will be shipping shortly after.

widdlekitty · « **Reply #93 on:** Wed, 01 August 2018, 18:56:44 »

My artisans are lubed and ready.

hayt · « **Reply #94 on:** Fri, 03 August 2018, 10:32:11 »

All remaining cases have been shipped! Thanks all for your support.

I currently have one left-over and 3 more trays without lids. In order to order 3 more lids, they will run me ~$30 each due to the high cost for ordering a small quantity. Once I can obtain those lids I will do a left-over raffle for the remaining (4) cases. TY <3

Lormania · « **Reply #95 on:** Fri, 03 August 2018, 10:37:23 »

Sounds good!

jackedhardwarejunkie · « **Reply #96 on:** Fri, 03 August 2018, 11:05:00 »

Quote from: hayt on Fri, 03 August 2018, 10:32:11

All remaining cases have been shipped! Thanks all for your support.

I currently have one left-over and 3 more trays without lids. In order to order 3 more lids, they will run me ~$30 each due to the high cost for ordering a small quantity. Once I can obtain those lids I will do a left-over raffle for the remaining (4) cases. TY <3

Thankyou bruva

fishinaspacesuit · « **Reply #97 on:** Sat, 29 September 2018, 09:36:27 »

Any plans to have a R2? =)

oscdawg · « **Reply #98 on:** Sat, 29 September 2018, 11:01:01 »

Excited for the left over raffle! Hopefully I get lucky

Sent from my Pixel XL using Tapatalk

sncbraxsc2 · « **Reply #99 on:** Fri, 12 October 2018, 09:29:32 »

Quote from: fishinaspacesuit on Sat, 29 September 2018, 09:36:27

Any plans to have a R2? =)

I have interest in this as well

smurkcity12 · « **Reply #100 on:** Fri, 12 October 2018, 17:34:09 »

Quote from: sncbraxsc2 on Fri, 12 October 2018, 09:29:32

Quote from: fishinaspacesuit on Sat, 29 September 2018, 09:36:27
Any plans to have a R2? =)

I have interest in this as well

I'd love to have another round as well.

lazyfart · « **Reply #101 on:** Sat, 13 October 2018, 09:49:21 »

Definitely keen on getting an extra! Also would love a R2

whitty · « **Reply #102 on:** Sat, 13 October 2018, 11:06:58 »

+1 for a round 2

Sent from my iPhone using Tapatalk

Hamel · « **Reply #103 on:** Sun, 14 October 2018, 23:11:03 »

Quote from: smurkcity12 on Fri, 12 October 2018, 17:34:09

Quote from: sncbraxsc2 on Fri, 12 October 2018, 09:29:32
Quote from: fishinaspacesuit on Sat, 29 September 2018, 09:36:27
Any plans to have a R2? =)

I have interest in this as well

I'd love to have another round as well.

+1 for R2.

hayt · « **Reply #104 on:** Mon, 15 October 2018, 13:26:30 »

Thanks All for your interest. Currently, I am all out of extras from R1.

There is a possibility for an R2 in the future. Playing around with a few ideas including switching from acrylic to aluminum for the body, and magnets instead of screws. At some point, I'll post up a new IC thread.

Thank you!
hayt

lazyfart · « **Reply #105 on:** Tue, 16 October 2018, 18:25:26 »

Really hope you do, I love how sleek your box looks! Maybe you should make it out of polycarb

Quote from: hayt on Mon, 15 October 2018, 13:26:30

Thanks All for your interest. Currently, I am all out of extras from R1.

There is a possibility for an R2 in the future. Playing around with a few ideas including switching from acrylic to aluminum for the body, and magnets instead of screws. At some point, I'll post up a new IC thread.

Thank you!
hayt

Sent from my SM-N920I using Tapatalk

Volsairine · « **Reply #106 on:** Thu, 18 October 2018, 02:32:07 »

Quote from: sncbraxsc2 on Fri, 12 October 2018, 09:29:32

Quote from: fishinaspacesuit on Sat, 29 September 2018, 09:36:27
Any plans to have a R2? =)

I have interest in this as well

Thirded!

amnesia0287 · « **Reply #107 on:** Sat, 20 October 2018, 09:24:47 »

Quote from: Volsairine on Thu, 18 October 2018, 02:32:07

Quote from: sncbraxsc2 on Fri, 12 October 2018, 09:29:32
Quote from: fishinaspacesuit on Sat, 29 September 2018, 09:36:27
Any plans to have a R2? =)

I have interest in this as well

Thirded!

Fourthed. And id probably get 2-3

Sleepy_Badger · « **Reply #108 on:** Wed, 23 January 2019, 22:13:37 »

is it possible to get one of these cases anymore?

yonghf · « **Reply #109 on:** Sat, 09 February 2019, 01:37:02 »

Looking for one as well, hoping for another round

Skribbles · « **Reply #110 on:** Sat, 09 February 2019, 03:25:03 »

Samesies! In for R2

P1kas · « **Reply #111 on:** Sat, 09 February 2019, 22:30:43 »

There will be no R2.

News:

Author Topic: [GB] Artisan Case v1 - Complete (Read 26348 times)