Post by: Mechboards on Fri, 06 April 2018, 04:52:04
Exclusive Hotswappable SMD RGB LED 60% Keyboard in ANSI, ISO, or HHKB. Supports QMK. Developed in partnership with Yiancar
Fits all standard and aftermarket 60% cases.
SEE MORE FOR FAQ’S
The PCB is compatible with QMK firmware. The PCB will ship fully complete, with all components in place.
V2 will include an ARM processor, and Matte Black finish.
This preorder will run for 2 weeks. Looking at delivery 8 weeks from now (18-25th Dec)
Ordering from Australia/NZ? – PREORDER FROM DAILYCLACK
Ordering from Canada? – PREORDER FROM MECHKEYS.CA (https://mechkeys.ca/products/hs60-pcb-gb)
Ordering from the US? – PREORDER LINK SOON
Did you order the V1? Get £15 off when ordering by entering your OLD order number in the notes section. We’ll then manually apply the discount after purchase. Order must be placed through Mechboards.co.uk
V1 -
Fits all standard and aftermarket 60% cases.
SEE MORE FOR FAQ’S
The PCB is compatible with QMK firmware. The PCB will ship fully complete, with all components in place.
V2 will include an ARM processor, and Matte Black finish.
This preorder will run for 2 weeks. Looking at delivery 8 weeks from now (18-25th Dec)
Ordering from Australia/NZ? – PREORDER FROM DAILYCLACK
Ordering from Canada? – PREORDER FROM MECHKEYS.CA (https://mechkeys.ca/products/hs60-pcb-gb)
Ordering from the US? – PREORDER LINK SOON
Did you order the V1? Get £15 off when ordering by entering your OLD order number in the notes section. We’ll then manually apply the discount after purchase. Order must be placed through Mechboards.co.uk
More
Q1: What about other layouts?
A1: We now have ANSI, ISO, HHKB layouts. We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector following the universal GH60 standard. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already. There are exposed pins to add underglow RGB strips, but this is experimental and up to the user.
Q4: Can I set the RGB?
A4: Yes! It comes with different styles as well as colour picker. QMK community is working toward a hosted software to do that as well but its still under development.
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
A1: We now have ANSI, ISO, HHKB layouts. We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector following the universal GH60 standard. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already. There are exposed pins to add underglow RGB strips, but this is experimental and up to the user.
Q4: Can I set the RGB?
A4: Yes! It comes with different styles as well as colour picker. QMK community is working toward a hosted software to do that as well but its still under development.
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
V1 -
More
Hotswap 60% in standard ANSI or ISO layouts. Fully soldered PCB with in-switch SMD RGB LED's, which fits all standard 60% cases and plates.
White PCB. Designed and assembled in the UK. QMK Support.
GB will run for 3 weeks (End 27th April) and looking to ship 2-3 weeks after for mid May release
[attachimg=2]
[attachimg=3]
2 versions:
ANSI in standard 60% layout
ISO in standard 60% layout
£50 for Group Buy, £65 after (plus shipping) - NEWS - We now have an NA proxy! thekey.company will be handling all orders to North America. Therefore I will be refunding shipping (besides £2.50 to cover my shipping to TKC) in due course and then TKC will send a separate invoice prior to final shipment. This will lower the shipping costs considerably.
https://mechboards.co.uk/shop/parts/hs60-pcb/
This will first be a GB and then stocked all the time at Mechboards.co.uk
We're also looking for non-EU stockists!
More images and details soon
FAQ
White PCB. Designed and assembled in the UK. QMK Support.
GB will run for 3 weeks (End 27th April) and looking to ship 2-3 weeks after for mid May release
[attachimg=2]
[attachimg=3]
2 versions:
ANSI in standard 60% layout
ISO in standard 60% layout
£50 for Group Buy, £65 after (plus shipping) - NEWS - We now have an NA proxy! thekey.company will be handling all orders to North America. Therefore I will be refunding shipping (besides £2.50 to cover my shipping to TKC) in due course and then TKC will send a separate invoice prior to final shipment. This will lower the shipping costs considerably.
https://mechboards.co.uk/shop/parts/hs60-pcb/
This will first be a GB and then stocked all the time at Mechboards.co.uk
We're also looking for non-EU stockists!
More images and details soon
FAQ
More
Q1: What about split shift/split backspace/other layouts?
A1: We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
A1: We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
Post by: Mechboards on Fri, 06 April 2018, 05:03:14
[attach=1]
[attach=2]
[attach=3]
[attach=4]
Post by: Signature on Fri, 06 April 2018, 08:37:50
Post by: Unforgivable on Fri, 06 April 2018, 09:39:46
Would love to see a HHKB + Winkeyless combo though.
Basically the HHKB layout, but with 1.5/1/1.5/7/1.5/1/1.5 bottom row layout, so there are no issues with the sockets and can be used in both manners. Would this be possible?
Post by: Perfex on Fri, 06 April 2018, 09:54:07
Post by: kmba on Fri, 06 April 2018, 10:09:01
Post by: Mechboards on Fri, 06 April 2018, 10:25:47
Because of the hotswap sockets, it's pretty impossible to add other layouts to the same PCB (and we'll be selling these fully soldered/built)
Cheers!
Post by: enrique.aliaga on Fri, 06 April 2018, 10:34:53
1. What kind of hot-swap sockets does this PCB have? Does it use "holtites"? Or does it use the Kailh hot-swap sockets (used by the K-Type, among others)?
2. Would it be possible to swap the stock PCB that comes with a Pok3r for this one? My goal is to have hot-swappability.
The project looks great, BTW! I wish you all the best.
Thanks!
Post by: Perfex on Fri, 06 April 2018, 12:42:41
Thanks for the comments guys. We've already got 2 PCB's for ANSI and ISO, and if we wanted one to include split shift and split bspace, that would be 4. To add HHKB/WKL to the mix, that would be 8 different PCB's to cover all variants. We will look into different layouts further down the line if they become really popular, but for now standard is the best approach :)
Because of the hotswap sockets, it's pretty impossible to add other layouts to the same PCB (and we'll be selling these fully soldered/built)
Cheers!
I completely understand and agree that the layouts you chose is the best route to take for the time being, good luck with the sale :)
Post by: odd on Fri, 06 April 2018, 12:43:19
Agreed on the hhkb/wkl support. Split shift, split backspace, wkl bottom.
Go buy a Zeal 60 then
Post by: yiancar on Fri, 06 April 2018, 16:21:27
Hi! Couple questions:
1. What kind of hot-swap sockets does this PCB have? Does it use "holtites"? Or does it use the Kailh hot-swap sockets (used by the K-Type, among others)?
2. Would it be possible to swap the stock PCB that comes with a Pok3r for this one? My goal is to have hot-swappability.
The project looks great, BTW! I wish you all the best.
Thanks!
1. It has Kailh sockets :)
2. Highly likely it has the standard mounting holes as GH60 etc.
Post by: befbef on Fri, 06 April 2018, 17:21:46
Post by: enrique.aliaga on Fri, 06 April 2018, 17:48:25
1. It has Kailh sockets :)
2. Highly likely it has the standard mounting holes as GH60 etc.
That's great! I just joined the GB. My plan is to replace the stock Pok3r PCB with this one. :)
Post by: kmba on Fri, 06 April 2018, 19:20:51
Agreed on the hhkb/wkl support. Split shift, split backspace, wkl bottom.
Go buy a Zeal 60 then
Not hot swap and $55 more, but great advice :rolleyes:
Post by: Puddsy on Fri, 06 April 2018, 23:37:12
Post by: ArchDill on Fri, 06 April 2018, 23:50:34
Instant buy if it supported HHKB layout.
SAME.
I could care less about the LED's. Just having the hot swap would be nice.
Post by: kmba on Sat, 07 April 2018, 08:47:10
kailh hotswap sockets don't allow for layout choices, so this is the best you'll be able to get with that requirement
In the FAQ he says if enough people are interested in alternate layout on a new PCB he will look into it. People are just voicing that interest.
Post by: Puddsy on Sat, 07 April 2018, 09:54:36
kailh hotswap sockets don't allow for layout choices, so this is the best you'll be able to get with that requirement
In the FAQ he says if enough people are interested in alternate layout on a new PCB he will look into it. People are just voicing that interest.
i was just explaining why it's not there
i probably wouldn't buy an HHKB layout PCB, but i'm not the biggest fan of hotswap (just personal taste, the kailh hotswap sockets are a good implementation)
GLWGB, mechboards
Post by: befbef on Sat, 07 April 2018, 10:43:42
Quote
but i'm not the biggest fan of hotswapWhy? Do you feel the difference?
Post by: Puddsy on Sat, 07 April 2018, 11:45:43
Quotebut i'm not the biggest fan of hotswapWhy? Do you feel the difference?
just personal taste, i'm a bit of an elitist
i see the merit in it
Post by: Mechboards on Sat, 07 April 2018, 19:27:14
kailh hotswap sockets don't allow for layout choices, so this is the best you'll be able to get with that requirement
In the FAQ he says if enough people are interested in alternate layout on a new PCB he will look into it. People are just voicing that interest.
i was just explaining why it's not there
i probably wouldn't buy an HHKB layout PCB, but i'm not the biggest fan of hotswap (just personal taste, the kailh hotswap sockets are a good implementation)
GLWGB, mechboards
Thanks man! This is more for the beginners in buildling a keyboard, and for people who can't make a decision about which switch they want ;)
Post by: Mechboards on Mon, 09 April 2018, 10:21:08
Post by: Mechboards on Thu, 12 April 2018, 10:07:09
[attachimg=1]
[attachimg=4]
[attachimg=2]
Post by: enrique.aliaga on Thu, 12 April 2018, 10:10:45
BTW, does this PCB support GMK screw-in stabilizers?
Post by: Jae-3soteric on Thu, 12 April 2018, 10:29:18
Oh wow! Looks sweeeet.
BTW, does this PCB support GMK screw-in stabilizers?
I’ve watched the development of the board through David and Yiancar and it should do - I’m getting a prototype to test tomorrow direct from David so will confirm for sure then.
Additionally I’ll be streaming a live build of the HS60 with /u/Meliewx from the MKUK community a week on Saturday!!
Sent from my iPhone using Tapatalk
Post by: Mechboards on Thu, 12 April 2018, 10:38:57
Post by: enrique.aliaga on Thu, 12 April 2018, 11:00:38
The PCB will allow GMK screw-in stabilisers :)
Awesome! Thanks for the response.
Would it be possible to combine this PCB with GMK screw-in stabilizers and the plate from a Pok3r?
I think I would have to discard the Pok3r’s stock Cherry plate-mount stabilizers. Right?
Or would I be better off buying a separate plate just for this build?
Thanks for the guidance.
Sent from my iPhone using Tapatalk
Post by: Mechboards on Thu, 12 April 2018, 11:03:00
The PCB will allow GMK screw-in stabilisers :)
Awesome! Thanks for the response.
Would it be possible to combine this PCB with GMK screw-in stabilizers and the plate from a Pok3r?
I think I would have to discard the Pok3r’s stock Cherry plate-mount stabilizers. Right?
Or would I be better off buying a separate plate just for this build?
Thanks for the guidance.
Sent from my iPhone using Tapatalk
Yes! All plates and cases for a standard 60% work with this PCB. We're also running a GB for Screw-ins at the moment if you need them.
Post by: enrique.aliaga on Thu, 12 April 2018, 11:09:39
Sent from my iPhone using Tapatalk
Post by: pon10 on Thu, 12 April 2018, 11:12:33
( sry.. My QMK learning patience/time is no more ) :p
Post by: Vadurr on Fri, 13 April 2018, 03:01:53
Post by: Mechboards on Fri, 13 April 2018, 03:55:58
Is the pcb only with "RAW" QMK support? :confused: or does it comes with some predefined layouts & LED settings which is slightly easy accessible in some way :D
( sry.. My QMK learning patience/time is no more ) :p
It comes with a lot of preset settings and profiles :)
Post by: Anaconda on Sat, 14 April 2018, 00:28:43
Post by: pon10 on Sat, 14 April 2018, 05:49:11
I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
Try 1upkeyboards.. They seem to have a ISO PRO PLATE. :thumb:
Post by: Jae-3soteric on Sat, 14 April 2018, 07:12:33
I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then :)
Sent from my iPhone using Tapatalk
Post by: Mechboards on Mon, 16 April 2018, 07:18:52
Post by: enrique.aliaga on Mon, 16 April 2018, 09:05:19
I’d love to watch that! Where can I find it? :)I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then :)
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Post by: enrique.aliaga on Mon, 16 April 2018, 09:10:22
NEWS - We now have an NA proxy! thekey.company will be handling all orders to North America. Therefore I will be refunding shipping (besides £2.50 to cover my shipping to TKC) in due course and then TKC will send a separate invoice prior to final shipment. This will lower the shipping costs considerably.What about the South American customers. Also going to get our orders shipped from the US?
Sent from my iPhone using Tapatalk
Post by: Mechboards on Mon, 16 April 2018, 09:19:46
Sure, if it works out cheaper. We'll check it out.NEWS - We now have an NA proxy! thekey.company will be handling all orders to North America. Therefore I will be refunding shipping (besides £2.50 to cover my shipping to TKC) in due course and then TKC will send a separate invoice prior to final shipment. This will lower the shipping costs considerably.What about the South American customers. Also going to get our orders shipped from the US?
Sent from my iPhone using Tapatalk
Sent from my F5121 using Tapatalk
Post by: Jae-3soteric on Mon, 16 April 2018, 10:46:56
I’d love to watch that! Where can I find it? :)I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then :)
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
It will be on twitch. I’ll post some details up in this thread in a couple of days once we work out all the detail
Sent from my iPhone using Tapatalk
Post by: Jae-3soteric on Fri, 20 April 2018, 08:21:53
I’d love to watch that! Where can I find it? :)I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then :)
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
here are the details of the livestream build:
https://www.reddit.com/r/MechanicalKeyboards/comments/8dnh05/mechboards_hs60_livestream_build/
Post by: enrique.aliaga on Fri, 20 April 2018, 10:33:32
I’d love to watch that! Where can I find it? :)I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then :)
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
here are the details of the livestream build:
https://www.reddit.com/r/MechanicalKeyboards/comments/8dnh05/mechboards_hs60_livestream_build/
Thanks! I'm eagerly awaiting! Are you going to use Cherry screw-in stabilizers, just like the ones in the other MechBoards' group buy? I ordered those, too. :)
Post by: Jae-3soteric on Fri, 20 April 2018, 10:34:51
Post by: Mechboards on Tue, 24 April 2018, 02:28:34
[attachimg=1]
Post by: Jae-3soteric on Tue, 24 April 2018, 02:54:59
Swires got in on the action
(Attachment Link)
Nice! I stole the image for the opening of my stream at the weekend!!
If anyone wants to re-watch the livestream build you can check it out at twitch/jaekeebs
Sent from my iPhone using Tapatalk
Post by: Mechboards on Tue, 24 April 2018, 08:07:11
Post by: oldcat on Wed, 25 April 2018, 20:27:25
Post by: audax989 on Wed, 25 April 2018, 20:47:34
Post by: oldcat on Wed, 25 April 2018, 21:07:25
Post by: Vadurr on Thu, 26 April 2018, 12:32:12
Post by: Mechboards on Mon, 30 April 2018, 05:38:12
Post by: Mechboards on Thu, 03 May 2018, 06:37:18
PCB's are in production.
All parts/components have been ordered
Post by: TheDankMatter on Tue, 08 May 2018, 06:47:10
Post by: Jae-3soteric on Tue, 08 May 2018, 10:32:00
Sent from my iPhone using Tapatalk
Post by: Vadurr on Tue, 08 May 2018, 11:11:23
Olivia and I have commissioned a limited run to test a HHKB layout - david from Mechboards might run after :)
Sent from my iPhone using Tapatalk
I'd be in for a few if this is true! :thumb:
Post by: profanum429 on Tue, 08 May 2018, 11:31:34
Olivia and I have commissioned a limited run to test a HHKB layout - david from Mechboards might run after :)
Sent from my iPhone using Tapatalk
I'd definitely be in for some of these!
Post by: JDragon on Tue, 08 May 2018, 12:36:47
Post by: audax989 on Tue, 08 May 2018, 23:37:37
Olivia and I have commissioned a limited run to test a HHKB layout - david from Mechboards might run after :)
Sent from my iPhone using Tapatalk
definitely be interested as well.
Post by: Krytone on Wed, 09 May 2018, 02:07:47
Count me inOlivia and I have commissioned a limited run to test a HHKB layout - david from Mechboards might run after :)
Sent from my iPhone using Tapatalk
definitely be interested as well.
Post by: Mechboards on Thu, 10 May 2018, 05:06:19
[attachimg=1]
Post by: pixelpusher on Thu, 10 May 2018, 11:27:24
Bare PCB's have arrived, time to pick n place!
(Attachment Link)
Nice! Glad to see those left shift stabilizer holes cut out. Not that I didn't trust you... but y'know.
You say bare, so does that mean you are doing all of the surface mount soldering?
Last question... when could one expect these boards to leave you and be en route to us?
Post by: enrique.aliaga on Thu, 10 May 2018, 15:55:04
Any recommendation for a nice aluminum plate to go along this PCB?
I've seen Sentraq selling one in their website (with a nice Champagne Gold color); and am also aware of KBDfans selling them in their stores. Are these good options? Any other vendor I should be aware of?
Thanks!!
Post by: pixelpusher on Thu, 10 May 2018, 16:24:55
Hey guys! I'm excited to get this plate and do my very first build!
Any recommendation for a nice aluminum plate to go along this PCB?
I've seen Sentraq selling one in their website (with a nice Champagne Gold color); and am also aware of KBDfans selling them in their stores. Are these good options? Any other vendor I should be aware of?
Thanks!!
Both of those plates are fine and basically the same quality. I've ordered two from each vendor. I had a problem with one from KBDFans where the side had been crushed a bit and I couldn't get it back in the right shape (which is usually pretty easy for aluminum), and they sent a replacement quickly. The only ones I've had issue with is the ones made for costar stabilizers (i think they sell them on aliexpress and ebay both). The plate was too large to fit most of my 60% cases. But the ones you mention shouldn't have that issue.
Post by: Anaconda on Mon, 14 May 2018, 13:13:23
Post by: Mechboards on Tue, 15 May 2018, 05:36:36
[attachimg=1]
Post by: meliewx on Fri, 18 May 2018, 09:47:52
Sent from my Pixel 2 XL using Tapatalk
Post by: enrique.aliaga on Fri, 18 May 2018, 10:07:24
I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then
Sent from my iPhone using Tapatalk
Hey guys, I finally ordered a Sentraq aluminum plate in Universal Layout. I am worried now that maybe I should have got the ANSI one instead.
Are the Kailh hot swap sockets loose on Universal Plates?
Thanks!
P.S.: I may still have time to change my Sentraq order.
Sent from my iPhone using Tapatalk
Post by: Lisinge on Fri, 18 May 2018, 10:46:27
I would like to see an ISO only plate on your website. Universal plate might be really loose with kailh hotswap sockets for a 60% board. There is really no one selling ISO only plates any where.
It’s something I’ve mentioned to David as well. I’m doing a livestream build of a prototype HS60 a week today with Meliewx - we will be using a universal plate so will be able to confirm then
Sent from my iPhone using Tapatalk
Hey guys, I finally ordered a Sentraq aluminum plate in Universal Layout. I am worried now that maybe I should have got the ANSI one instead.
Are the Kailh hot swap sockets loose on Universal Plates?
Thanks!
P.S.: I may still have time to change my Sentraq order.
Sent from my iPhone using Tapatalk
It's really not that bad but yes some switches will be a bit looser than others where there is no alu on top or bottom of the switch where the switch clips are at, for example the pipe key.
I i were you and i got a ansi pcb them i would get the andi plate. Your switches will have a better fit and if you want to you could always so the plate later
Post by: enrique.aliaga on Fri, 18 May 2018, 13:25:59
I’m gonna try to get my order changed and get an ANSI one instead of the Universal.
Sent from my iPad using Tapatalk
Post by: rjsf on Tue, 22 May 2018, 15:26:49
Post by: Eon2001 on Fri, 25 May 2018, 12:42:07
All ordered ISO's have been completed. I just need to pick them up and get them posted which will happen over the next week or so :)
(Attachment Link)
An update on ANSI PCBs would be appreciated.
Post by: Mechboards on Sun, 27 May 2018, 19:01:43
Post by: Skaazi on Mon, 28 May 2018, 14:26:52
Post by: Anaconda on Tue, 29 May 2018, 18:53:27
Post by: Vadurr on Tue, 29 May 2018, 19:11:24
Post by: GreyAmbience on Thu, 31 May 2018, 01:53:07
Post by: Skaazi on Fri, 01 June 2018, 18:03:35
Post by: Mechboards on Sat, 02 June 2018, 07:53:11
Here are the ANSI ones
[attachimg=1]
Post by: yonghf on Sat, 02 June 2018, 10:06:18
So all individual orders have been either shipped for EU customers, or shipped to US proxy. All other orders that are combined with GMK stabs (for example) will need to wait till mid June sadly as that is when GMK will ship.
Here are the ANSI ones
(Attachment Link)
I sent an email regarding Order #1143.
Post by: Lisinge on Sat, 02 June 2018, 11:41:38
So all individual orders have been either shipped for EU customers, or shipped to US proxy. All other orders that are combined with GMK stabs (for example) will need to wait till mid June sadly as that is when GMK will ship.
Haven't gotten any tracking info but maybe there are no tracking? I ordered only PCBs
Post by: Yeoh on Tue, 05 June 2018, 09:13:13
So all individual orders have been either shipped for EU customers, or shipped to US proxy. All other orders that are combined with GMK stabs (for example) will need to wait till mid June sadly as that is when GMK will ship.
Haven't gotten any tracking info but maybe there are no tracking? I ordered only PCBs
No tracking here, either.
I guess time will tell.
Post by: nimblejacks on Sat, 09 June 2018, 08:01:48
Post by: Darknight00z on Wed, 13 June 2018, 15:33:28
Post by: manitoid on Wed, 13 June 2018, 23:07:26
Post by: Mechboards on Thu, 14 June 2018, 03:41:35
Sent from my F5121 using Tapatalk
Post by: Fatboychard on Thu, 14 June 2018, 03:54:12
Post by: Lisinge on Thu, 14 June 2018, 04:23:49
Post by: Yeoh on Fri, 15 June 2018, 22:38:22
I thought these were shipped at the beginning of the month?
Post by: Skaazi on Mon, 18 June 2018, 00:30:20
Wondering if anyone has received an hs60 yet?
I thought these were shipped at the beginning of the month?
Nothing here in the US yet.
Post by: pixelpusher on Wed, 20 June 2018, 10:48:45
Post by: yonghf on Thu, 21 June 2018, 06:39:49
Post by: Mechboards on Thu, 21 June 2018, 06:43:36
Is there supposed to be a tracking number? I just got an email that it shipped but no tracking information.I'll be adding tracking to the orders a little later :)
Sent from my F5121 using Tapatalk
Post by: nimblejacks on Fri, 22 June 2018, 08:09:08
Post by: Mechboards on Fri, 22 June 2018, 08:14:42
Sent from my F5121 using Tapatalk
Post by: pixelpusher on Sat, 23 June 2018, 16:32:50
I'm in the middle of packing for a week long vacation, so I don't know that I'll be able to test out much. I'll report back what I can.
I do know that it won't fit in a Tex low profile case b/c of a diode by the USB cable. Those cases have supports going across that restrict quite a few PCBs. I wasn't really expecting it to work. I'll try some more cases tonight if I have time.
Post by: olivia on Sat, 23 June 2018, 16:35:57
(https://cdn.discordapp.com/attachments/419169658315210753/460195460964024320/IMG_20180623_173041.jpg)
Post by: Skaazi on Sat, 23 June 2018, 19:09:44
Post by: pixelpusher on Sat, 23 June 2018, 21:06:10
Doesn't fit properly in Klippie (D2 diode is like RIGHT NEXT to the mounting hole) It will go in if you put the PCB off-center which, I will not.
Doesn't fit in the 5degree case from KBDFans. The extra two top screw mounts on that case come into contact with a diode and the hot-swap pieces on the back of the PCB.
Doesn't fit in Aliexpress wooden case (something making contact on the left and also the middle screw support)
Soooo.... I don't have any cases this will work in.
I guess I can put it in my TX60, although I'm not sure how a hotswap board works in a top mount board... maybe it will NOT just fall out? Maybe the PCB mounted stablizers will hold it in? AND I just remembered my TX60 is HHKB layout and this has no split right shift. Hmm... I've got 5 empty cases that this PCB will not go in. This blows.
Anyone have a case this fits in?
Post by: pixelpusher on Sat, 23 June 2018, 23:02:27
Post by: Jae-3soteric on Sun, 24 June 2018, 02:27:03
Okay, here's what I've tested:
Doesn't fit properly in Klippie (D2 diode is like RIGHT NEXT to the mounting hole) It will go in if you put the PCB off-center which, I will not.
Doesn't fit in the 5degree case from KBDFans. The extra two top screw mounts on that case come into contact with a diode and the hot-swap pieces on the back of the PCB.
Doesn't fit in Aliexpress wooden case (something making contact on the left and also the middle screw support)
Soooo.... I don't have any cases this will work in.
I guess I can put it in my TX60, although I'm not sure how a hotswap board works in a top mount board... maybe it will NOT just fall out? Maybe the PCB mounted stablizers will hold it in? AND I just remembered my TX60 is HHKB layout and this has no split right shift. Hmm... I've got 5 empty cases that this PCB will not go in. This blows.
Anyone have a case this fits in?
So I’ve got an ISO one here, and it works in a 5degree case - a bit of tape over the additional mount stops it shorting.
I have a wooden royal glam case, no issues whatsoever. I’ve got another cheap Ali wooden case that’s low pro - again no issues.
It also works just fine in my tina C, tx60 as top mount (seems held in pretty darn tight).
My klippe and revo also have 0 problems.
Do you have a pic of the pcb? I’m wondering if there is some part that is catching just on your one.
Sent from my iPhone using Tapatalk
Post by: pixelpusher on Sun, 24 June 2018, 04:24:41
Than the bottom (now a different angle than the case). Also, it will only go in the Klippie if you put it all the way to the left edge, leaving a larger gap of about 3mm on the right. And when I use it this way it disconnects from windows about every 20 seconds. I’ve already asked for a refund
Post by: Skaazi on Sun, 24 June 2018, 12:24:22
Post by: pixelpusher on Sun, 24 June 2018, 12:52:40
Post by: pixelpusher on Sun, 24 June 2018, 13:20:34
Post by: oyaji on Mon, 25 June 2018, 10:58:03
Is it likely to ship any time soon?
Post by: Mechboards on Mon, 25 June 2018, 11:04:35
It looks like people in the US have received theirs now, but my ANSI PCB order to Australia doesn’t look like it shipped yet. I didn’t order stabs.Hey man! PM me your order number and I'll take a look. From memory we've got an Australia order packed, just haven't got round to posting it yet :)
Is it likely to ship any time soon?
Sent from my F5121 using Tapatalk
Post by: yonghf on Mon, 25 June 2018, 11:44:22
Is there supposed to be a tracking number? I just got an email that it shipped but no tracking information.I'll be adding tracking to the orders a little later :)
Sent from my F5121 using Tapatalk
Sorry, where exactly should I look for my tracking number?
Post by: olivia on Tue, 26 June 2018, 00:17:41
(https://cdn.discordapp.com/attachments/393371266532245504/461220062120902686/IMG_20180626_132307.jpg)
Post by: Lisinge on Tue, 26 June 2018, 04:11:05
Post by: Mechboards on Tue, 26 June 2018, 04:14:00
Have to say i'm a bit disappointed that the pcbs made it all the way to the US and out to buyers before receiving the two i ordered here in the EU. I didn't even get any stabilizers or anything else...
Sent from my F5121 using Tapatalk
Post by: pixelpusher on Tue, 26 June 2018, 11:25:46
Post by: redbanshee on Tue, 26 June 2018, 12:11:11
Post by: manofinterests on Tue, 26 June 2018, 12:37:26
Will they be available in the next round?
Post by: Jae-3soteric on Tue, 26 June 2018, 12:39:14
A bit salty that mx hhkb versions were made but unavailable to the rest of us :blank:
Will they be available in the next round?
There were just a handful of prototypes made of the mx hhkb version
I can’t speak for David but I’m pretty sure there will be more made
Sent from my iPhone using Tapatalk
Post by: Vadurr on Tue, 26 June 2018, 12:42:08
A bit salty that mx hhkb versions were made but unavailable to the rest of us :blank:
Will they be available in the next round?
There were just a handful of prototypes made of the mx hhkb version
I can’t speak for David but I’m pretty sure there will be more made
Sent from my iPhone using Tapatalk
Please!
Post by: Skaazi on Tue, 26 June 2018, 12:50:20
Is there a users guide or a link to firmware for the hs60?
I grabbed the FLIP driver from https://zealpc.net/blogs/news/programming-your-zeal60-rgb-pcb (https://zealpc.net/blogs/news/programming-your-zeal60-rgb-pcb) then compiled the HS60 firmware https://github.com/qmk/qmk_firmware/tree/master/keyboards/hs60 (https://github.com/qmk/qmk_firmware/tree/master/keyboards/hs60). I think the one in Wilba's fork is outdated. Then in AVRDUDESS I used the FLIP USB DFU protocol version 1 programmer with the usb port to flash it.
Post by: olivia on Tue, 26 June 2018, 12:54:21
Post by: Lisinge on Wed, 27 June 2018, 16:15:17
The ANSI one has a missing led, the legs are there but they've been completely ripped out of the led and the led were loose in the bag the PCB came in.
I can reflash the PCB and it works.
(https://s3-eu-west-1.amazonaws.com/mick.es/IMG_0646.jpg)
The ISO one has a bunch of leds not lighting up, it does not let me flash it. In fact, it's not even recognized in windows as a USB device and it wont get into the bootloader with the switch on the underside. It does not respond to keypresses to change led settings either.
(https://s3-eu-west-1.amazonaws.com/mick.es/IMG_0648.jpg)
Post by: pixelpusher on Sat, 30 June 2018, 10:11:17
I've submitted the issue through the help on Mechboards website and I've PMd here. It's been almost a week with no response. Let me know if there is a different way to get customer support. Does anyone have contact info on discord?
Post by: Lisinge on Sat, 30 June 2018, 10:16:31
I still keep keeping randomly disconnected (on average about two minutes). I've tried 3 different cables and two different computers (one PC one mac). I reflashed the firmware, which seemed to help at first, but now it just disconnects a bit less often. While I was typing this post, the led mode changed on it's own and was stuck (wouldn't respond to FN + Z to go to a different mode).
I've submitted the issue through the help on Mechkeyboards website and I've PMd here. It's been almost a week with no response. Let me know if there is a different way to get customer support. Does anyone have contact info on discord?
I saw this in a PCB i've yet to fully assemble, i had to repair a LED by taking a LED from a donor board to get it working. And it happened at least two times that the led animation got stuck and the pcb was unresponsive. Then i'm not the only one...
You can try and PM Yiancar on discord, he has been really helpful, but unfortunately mechboards seems to be hard to get an answer from.
Post by: pixelpusher on Sat, 30 June 2018, 10:38:38
I still keep keeping randomly disconnected (on average about two minutes). I've tried 3 different cables and two different computers (one PC one mac). I reflashed the firmware, which seemed to help at first, but now it just disconnects a bit less often. While I was typing this post, the led mode changed on it's own and was stuck (wouldn't respond to FN + Z to go to a different mode).
I've submitted the issue through the help on Mechkeyboards website and I've PMd here. It's been almost a week with no response. Let me know if there is a different way to get customer support. Does anyone have contact info on discord?
I saw this in a PCB i've yet to fully assemble, i had to repair a LED by taking a LED from a donor board to get it working. And it happened at least two times that the led animation got stuck and the pcb was unresponsive. Then i'm not the only one...
You can try and PM Yiancar on discord, he has been really helpful, but unfortunately mechboards seems to be hard to get an answer from.
It seems to be related to the firmware and not user input, b/c I can walk away and come back to it messed up. It doesn't seem to be related to a keypress.
Post by: Lisinge on Sat, 30 June 2018, 10:40:01
Yup, and after some testing i can see it happens on several of the animationsI still keep keeping randomly disconnected (on average about two minutes). I've tried 3 different cables and two different computers (one PC one mac). I reflashed the firmware, which seemed to help at first, but now it just disconnects a bit less often. While I was typing this post, the led mode changed on it's own and was stuck (wouldn't respond to FN + Z to go to a different mode).
I've submitted the issue through the help on Mechkeyboards website and I've PMd here. It's been almost a week with no response. Let me know if there is a different way to get customer support. Does anyone have contact info on discord?
I saw this in a PCB i've yet to fully assemble, i had to repair a LED by taking a LED from a donor board to get it working. And it happened at least two times that the led animation got stuck and the pcb was unresponsive. Then i'm not the only one...
You can try and PM Yiancar on discord, he has been really helpful, but unfortunately mechboards seems to be hard to get an answer from.
It seems to be related to the firmware and not user input, b/c I can walk away and come back to it messed up. It doesn't seem to be related to a keypress.
Post by: rjsf on Sat, 30 June 2018, 23:34:00
Post by: yonghf on Sat, 30 June 2018, 23:43:20
I live in the CA, US. I still have not received my ANSI board. Am I the only one here who has not received it yet? What's going on? You guys have not responded to me about where the heck my item is. I'm close to filing a Paypal chargeback.
Mine is supposedly shipped on 18 June but I don't see any tracking information. No replies from vendor either.
Post by: rjsf on Sun, 01 July 2018, 00:53:13
I live in the CA, US. I still have not received my ANSI board. Am I the only one here who has not received it yet? What's going on? You guys have not responded to me about where the heck my item is. I'm close to filing a Paypal chargeback.
Mine is supposedly shipped on 18 June but I don't see any tracking information. No replies from vendor either.
Yup, lack of communication if pretty irritating. I'm fine if they tell me my item will come after ten years, at least they let me know. But being put in the dark like this is the worst.
Post by: Mechboards on Sun, 01 July 2018, 04:00:50
Sent from my F5121 using Tapatalk
Post by: pixelpusher on Sun, 01 July 2018, 10:47:30
Post by: Mechboards on Sun, 01 July 2018, 11:17:15
My PCB no workie. Who Should I talk to about getting a new one or my money back?Pester us on email and we'll reply
Sent from my F5121 using Tapatalk
Post by: pixelpusher on Sun, 01 July 2018, 14:13:53
My PCB no workie. Who Should I talk to about getting a new one or my money back?Pester us on email and we'll reply
Sent from my F5121 using Tapatalk
Thanks. I just sent an email. I found out that it is definitely the LEDs causing the issue. I turned off the leds and I've not had a disconnect for over 6 hours. The longest I went before was about 2min. Perhaps a failing resistor is causing a surge to the controller? That's a bit beyond my troubleshooting abilities.
Post by: pixelpusher on Sun, 01 July 2018, 19:06:21
Can confirm that mine fits inside my X60 :DShow Image(https://cdn.discordapp.com/attachments/393371266532245504/461220062120902686/IMG_20180626_132307.jpg)
what the... how do you have a split right shift? That's not even an option
Nevermind... I see a few posts back a couple were made special.
Hey, the good news is, my RGB leds are completely dead now. That is actually good news b/c now my PCB doesn't disconnect anymore :p
Post by: yonghf on Mon, 02 July 2018, 08:35:45
Post by: nimblejacks on Mon, 02 July 2018, 10:41:50
Post by: rjsf on Mon, 02 July 2018, 18:37:37
Can confirm that mine fits inside my X60 :DShow Image(https://cdn.discordapp.com/attachments/393371266532245504/461220062120902686/IMG_20180626_132307.jpg)
what the... how do you have a split right shift? That's not even an option
Nevermind... I see a few posts back a couple were made special.
Hey, the good news is, my RGB leds are completely dead now. That is actually good news b/c now my PCB doesn't disconnect anymore :p
Yup, some real cool stuff is going on out there and people got theirs already. Meanwhile, I still have no status of my regular 60%.
Post by: rjsf on Mon, 02 July 2018, 18:53:53
Hey all. We've only got about 10 more orders to ship. I'll try and get tracking out to you guys that have already shipped. We're sorry about the lack of communication, moving office has really put us on the back foot but I'll try and get to all of you over the next couple of days
Sent from my F5121 using Tapatalk
Hey thanks at least for responding. But note, on top of the tracking number you owe me, I need to know the status of the refund for the extra shipping charge. You informed us that US residents will get some refund because you will be shipping through a proxy. The refund is not really a big deal, but again, at least I need some sort of communication, e.g. how will you refund me? do I need to do anything on my side? did you decide not to refund me? etc..
Also, let me know how you will update the tracking number to me, e.g. will you update the tracking number on my paypal transaction? Or will you email me the tracking number? Or will you PM me the tracking number? etc.
Post by: Lisinge on Tue, 03 July 2018, 05:45:26
Can confirm that mine fits inside my X60 :DShow Image(https://cdn.discordapp.com/attachments/393371266532245504/461220062120902686/IMG_20180626_132307.jpg)
what the... how do you have a split right shift? That's not even an option
Nevermind... I see a few posts back a couple were made special.
Hey, the good news is, my RGB leds are completely dead now. That is actually good news b/c now my PCB doesn't disconnect anymore :p
Well, now i've thoroughly tested the PCB that i got that i thought was working, turns out it's also crashing randomly like yours....
This is really getting tiresome
Post by: Mechboards on Tue, 03 July 2018, 05:57:58
If anyone is having issues beyond that, we will offer refunds and apologise if this is the case. We are planning a v2 which will be manufactured and tested correctly. V1 was partly hand placed which may have caused some of these issues.
Cheers
David
Sent from my F5121 using Tapatalk
Post by: Lisinge on Tue, 03 July 2018, 06:23:43
Yiancar has been of great help during this and i want to say that i sympathize with David moving office in the middle of all of this. Being a bit more responsive would keep peeps like me happy though ;D
Post by: pixelpusher on Tue, 03 July 2018, 09:52:42
Just wanted to chuck in that the PCB works great by just decreasing brightness one or two click. It's still really bright and it has to do with usb not being able to supply enough current.
Yiancar has been of great help during this and i want to say that i sympathize with David moving office in the middle of all of this. Being a bit more responsive would keep peeps like me happy though ;D
I put mine on the lowest brightness possible and it still disconnected randomly. As of now the leds do not work at all. But I'm in the process of sending it back.
Post by: nimblejacks on Wed, 04 July 2018, 13:47:30
Post by: rjsf on Tue, 10 July 2018, 14:34:47
Post by: Mechboards on Tue, 10 July 2018, 15:29:02
I received mine now and so far so good. Is there a list of keyboard shortcuts to control the LEDs?You should've got a piece of paper with your PCB. If not Google HS60 info Mechboards
Sent from my F5121 using Tapatalk
Post by: rjsf on Tue, 10 July 2018, 23:24:30
I received mine now and so far so good. Is there a list of keyboard shortcuts to control the LEDs?You should've got a piece of paper with your PCB. If not Google HS60 info Mechboards
Sent from my F5121 using Tapatalk
Thanks. Unfortunately I could not find any piece of paper in the box the PCB came in. Could you send me a copy or the link? I tried googling but could not find anything, I did find the qmk code I could reflash with but I just want to see the default map for now. I figured out some of the keys on my own via trial and error. E.g. to turn on and off the lights is Fn-Z. But I can't find other keys such as the PgUp PgDn keys.
Post by: gutsack on Tue, 10 July 2018, 23:42:24
I received mine now and so far so good. Is there a list of keyboard shortcuts to control the LEDs?You should've got a piece of paper with your PCB. If not Google HS60 info Mechboards
Sent from my F5121 using Tapatalk
Thanks. Unfortunately I could not find any piece of paper in the box the PCB came in. Could you send me a copy or the link? I tried googling but could not find anything, I did find the qmk code I could reflash with but I just want to see the default map for now. I figured out some of the keys on my own via trial and error. E.g. to turn on and off the lights is Fn-Z. But I can't find other keys such as the PgUp PgDn keys.
I think you're looking for this: https://github.com/qmk/qmk_firmware/blob/master/keyboards/hs60/keymaps/default/readme.md
You'll note that it isn't a very thorough keymap, so things like PgUp aren't mapped by default.
Post by: joe405 on Tue, 10 July 2018, 23:59:24
Post by: Franzl on Wed, 11 July 2018, 08:35:29
Post by: Mechboards on Wed, 11 July 2018, 08:49:04
I received mine now and so far so good. Is there a list of keyboard shortcuts to control the LEDs?You should've got a piece of paper with your PCB. If not Google HS60 info Mechboards
Sent from my F5121 using Tapatalk
Thanks. Unfortunately I could not find any piece of paper in the box the PCB came in. Could you send me a copy or the link? I tried googling but could not find anything, I did find the qmk code I could reflash with but I just want to see the default map for now. I figured out some of the keys on my own via trial and error. E.g. to turn on and off the lights is Fn-Z. But I can't find other keys such as the PgUp PgDn keys.
I think you're looking for this: https://github.com/qmk/qmk_firmware/blob/master/keyboards/hs60/keymaps/default/readme.md
You'll note that it isn't a very thorough keymap, so things like PgUp aren't mapped by default.
Hey it's this link - https://mechboards.co.uk/info-hs60/ - the rest of the FN layer wasn't mapped but you're more than welcome to map to your liking!
Will the next version also offer wkl/hhkb layouts? Any ETA?
Next version will have a WKL/HHKB layout, yea. Hopefully a couple months or so (finding new manufacturer)
Whats about orders with iso-pcb and stabs? Are they on the road already?
All orders have been sent. If you haven't received anything or have yet to get a tracking number - PM us your order number and we'll get right on it.
Post by: rjsf on Thu, 12 July 2018, 18:38:43
I received mine now and so far so good. Is there a list of keyboard shortcuts to control the LEDs?You should've got a piece of paper with your PCB. If not Google HS60 info Mechboards
Sent from my F5121 using Tapatalk
Thanks. Unfortunately I could not find any piece of paper in the box the PCB came in. Could you send me a copy or the link? I tried googling but could not find anything, I did find the qmk code I could reflash with but I just want to see the default map for now. I figured out some of the keys on my own via trial and error. E.g. to turn on and off the lights is Fn-Z. But I can't find other keys such as the PgUp PgDn keys.
I think you're looking for this: https://github.com/qmk/qmk_firmware/blob/master/keyboards/hs60/keymaps/default/readme.md
You'll note that it isn't a very thorough keymap, so things like PgUp aren't mapped by default.
Yeah, I found it. Thanks. I guess the default one is not much use, need to reflash off the bat.
Post by: rjsf on Sat, 14 July 2018, 16:56:50
I received mine now and so far so good. Is there a list of keyboard shortcuts to control the LEDs?You should've got a piece of paper with your PCB. If not Google HS60 info Mechboards
Sent from my F5121 using Tapatalk
Thanks. Unfortunately I could not find any piece of paper in the box the PCB came in. Could you send me a copy or the link? I tried googling but could not find anything, I did find the qmk code I could reflash with but I just want to see the default map for now. I figured out some of the keys on my own via trial and error. E.g. to turn on and off the lights is Fn-Z. But I can't find other keys such as the PgUp PgDn keys.
I think you're looking for this: https://github.com/qmk/qmk_firmware/blob/master/keyboards/hs60/keymaps/default/readme.md
You'll note that it isn't a very thorough keymap, so things like PgUp aren't mapped by default.
Hey it's this link - https://mechboards.co.uk/info-hs60/ - the rest of the FN layer wasn't mapped but you're more than welcome to map to your liking!Will the next version also offer wkl/hhkb layouts? Any ETA?
Next version will have a WKL/HHKB layout, yea. Hopefully a couple months or so (finding new manufacturer)Whats about orders with iso-pcb and stabs? Are they on the road already?
All orders have been sent. If you haven't received anything or have yet to get a tracking number - PM us your order number and we'll get right on it.
Thanks, although the default maps weren't adequate for me, it was easy to reflash. I compiled my new map and uploaded using qmk_toolbox.
Post by: Yeoh on Mon, 16 July 2018, 15:54:19
Post by: Mechboards on Mon, 16 July 2018, 15:57:24
Anyone else not able to get a response from Mechboards about defective hs60s lately?Send me a pm? We're trying to catch everyone
Sent from my F5121 using Tapatalk
Post by: Lisinge on Mon, 16 July 2018, 17:41:57
Anyone else not able to get a response from Mechboards about defective hs60s lately?
I've found most success on discord. Pm david, he's been responding to me, slow at times but still responding :)
Post by: silversilver on Tue, 07 August 2018, 05:10:19
thanks!
Post by: silversilver on Tue, 07 August 2018, 05:14:33
Post by: Mechboards on Tue, 07 August 2018, 06:41:41
Hello, I accidentally broke my HS60 ANSI PCB! Can I have the wiring map? Need to jump some wires.
PM us a picture :)
Post by: nimblejacks on Mon, 13 August 2018, 07:52:48
Post by: Mechboards on Mon, 13 August 2018, 08:55:56
Having several issues with the PCB and none of the fixes have solved the problems... sent a PM to you guys.I've sent it to the designer - awaiting reply
Sent from my F5121 using Tapatalk
Post by: nimblejacks on Fri, 17 August 2018, 12:27:36
Having several issues with the PCB and none of the fixes have solved the problems... sent a PM to you guys.I've sent it to the designer - awaiting reply
Sent from my F5121 using Tapatalk
When can I expect a response? Is there another method I can use to contact them directly? Thank you.
Post by: audax989 on Fri, 17 August 2018, 19:07:46
Post by: Lisinge on Fri, 17 August 2018, 20:30:12
will the hhkb ever see an official release? if anyone has one lying around I have the perfect board for it. :D
HHKB pcb is planned for round 2
Post by: umalip on Mon, 20 August 2018, 14:39:31
Post by: quint on Tue, 21 August 2018, 06:21:47
Post by: Mechboards on Tue, 21 August 2018, 09:15:42
Is anyone else having issues with keypresses not registering with this PCB? everything tested fine at first, then sporadically, had issues with presses not registering, and the board being unresponsive. Every hour or 2, i need to unplug my board, and re-plug to reset it. Am i the only one with these type of issues?
Same with mine. No problems at all when u switch off the leds.. Try that..
There are updated .hex files on the QMK depository which should solve these issues that you're having. We had to soft limit the LED's so they don't draw too much power. Just reflash with the updated .hex files. This should fix it :)
Post by: umalip on Tue, 21 August 2018, 10:38:21
Post by: quint on Wed, 22 August 2018, 06:48:54
Post by: umalip on Wed, 22 August 2018, 10:13:57
1) updated my QMK and msys2
2) copied the updated config.h file to my keyboard folder with my edits to layout
3) made a .hex file and uploaded that to the keyboard via the "Reset" (FN+rt bracket)
4) test out keyboard, and if i type too fast, certain key strokes do not register
Post by: silversilver on Wed, 22 August 2018, 10:22:20
Hello, I accidentally broke my HS60 ANSI PCB! Can I have the wiring map? Need to jump some wires.
PM us a picture :)
Pmed a few days ago. Please check. Thanks.
Post by: enrique.aliaga on Mon, 27 August 2018, 16:26:16
Post by: Keebmeupscotty on Fri, 31 August 2018, 09:36:56
To elaborate on it further, it doesn't seem to be all RGB modes that are causing problems. It is the default one (which I actually like the most) that does a slow rotating wave/windmill effect of changing colors. It seems that one and another that is similar are causing the missed keypresses, as I am able to use other rgb modes and turn off the leds all together and everything works fine. I have resorted to not using the leds at all, but would love to be able to turn them on without fearing my keypresses won't register and the board will randomly disconnect. Please advise if there is anything else I can do.
Post by: umalip on Wed, 05 September 2018, 08:14:25
Having the same issues as umalip and quint. I have reflashed with (I think) the most up to date version of the repo but am still having the issue.
To elaborate on it further, it doesn't seem to be all RGB modes that are causing problems. It is the default one (which I actually like the most) that does a slow rotating wave/windmill effect of changing colors. It seems that one and another that is similar are causing the missed keypresses, as I am able to use other rgb modes and turn off the leds all together and everything works fine. I have resorted to not using the leds at all, but would love to be able to turn them on without fearing my keypresses won't register and the board will randomly disconnect. Please advise if there is anything else I can do.
I have re-flashed my board multiple times with the new config files in the QMK folder and have tried turning off and on the NKRO, and i'm still having issues with the board not matching my typing speed. I have to type around 50-60 wpm just so it can keep up with my keystrokes.
Post by: Mechboards on Wed, 05 September 2018, 08:44:20
Having the same issues as umalip and quint. I have reflashed with (I think) the most up to date version of the repo but am still having the issue.
To elaborate on it further, it doesn't seem to be all RGB modes that are causing problems. It is the default one (which I actually like the most) that does a slow rotating wave/windmill effect of changing colors. It seems that one and another that is similar are causing the missed keypresses, as I am able to use other rgb modes and turn off the leds all together and everything works fine. I have resorted to not using the leds at all, but would love to be able to turn them on without fearing my keypresses won't register and the board will randomly disconnect. Please advise if there is anything else I can do.
I have re-flashed my board multiple times with the new config files in the QMK folder and have tried turning off and on the NKRO, and i'm still having issues with the board not matching my typing speed. I have to type around 50-60 wpm just so it can keep up with my keystrokes.
To both,
This is an issue with QMK and the controller which we can't fix I'm afraid. Try using less intense LED effects. This will be changed in V2.
Post by: umalip on Wed, 05 September 2018, 08:49:38
Having the same issues as umalip and quint. I have reflashed with (I think) the most up to date version of the repo but am still having the issue.
To elaborate on it further, it doesn't seem to be all RGB modes that are causing problems. It is the default one (which I actually like the most) that does a slow rotating wave/windmill effect of changing colors. It seems that one and another that is similar are causing the missed keypresses, as I am able to use other rgb modes and turn off the leds all together and everything works fine. I have resorted to not using the leds at all, but would love to be able to turn them on without fearing my keypresses won't register and the board will randomly disconnect. Please advise if there is anything else I can do.
I have re-flashed my board multiple times with the new config files in the QMK folder and have tried turning off and on the NKRO, and i'm still having issues with the board not matching my typing speed. I have to type around 50-60 wpm just so it can keep up with my keystrokes.
To both,
This is an issue with QMK and the controller which we can't fix I'm afraid. Try using less intense LED effects. This will be changed in V2.
Can i get a replacement v2 board? I can return this one i have currently.
Post by: voight-kampff on Mon, 10 September 2018, 12:27:53
Post by: hokie_programmer on Sat, 13 October 2018, 21:16:03
Never mind. I just had to reset it. All is good now.
Post by: TheDankMatter on Sun, 14 October 2018, 07:36:06
Post by: RETURNISO on Sun, 14 October 2018, 09:49:09
Post by: Mechboards on Sun, 14 October 2018, 10:06:38
Still waiting for HHKB layout to happen :thumb:
There will be one available :)
Hey everyone, I just got a PCB from someone off r/mm. It is registering all the keys correctly, but I might have broke the LED functionality. I turned it on and was tweaking all the settings and it looked like all the lights just suddenly turned off. Maybe the speed was too fast? Anyways, I cannot turn the light back on now. Anyone here have this problem before?
Never mind. I just had to reset it. All is good now.
Glad you got it sorted! Ify ou do have any issues with flashing etc moving forward lower the brightness of the LED's a couple clicks. Should help.
Are we gonna see a V2 ISO version soon? :eek:
See below :) Prototype being tested so we'll be going into production again soon.
[attachimg=1]
Post by: RETURNISO on Sun, 14 October 2018, 12:47:23
Are we gonna see a V2 ISO version soon? :eek:
See below :) Prototype being tested so we'll be going into production again soon.
(Attachment Link)
YESSS :thumb: what a beauty of a ISO RETURN(S) :p
Post by: towhatend on Wed, 17 October 2018, 13:49:17
Post by: Rumai on Wed, 17 October 2018, 19:40:33
Post by: Mechboards on Thu, 18 October 2018, 10:05:12
Will there be a version with ISO and split shift? :D
The GK64 already exists for 60% with arrows so I don't think we'll do split right shift :/
In for HHKB.
[attachimg=1]
Post by: RETURNISO on Thu, 18 October 2018, 12:07:13
Will there be a version with ISO and split shift? :D
The GK64 already exists for 60% with arrows so I don't think we'll do split right shift :/In for HHKB.
[attachimg=1]
Damn will all new v2 PCBAs be black? :eek: How long time are you thinking before we can hit the preorder button? :cool:
Post by: Mechboards on Tue, 23 October 2018, 07:01:00
There will be other stores with stock/preorders open as well so we'll keep you posted.
Post by: RETURNISO on Tue, 23 October 2018, 08:13:49
HS60 V2 preorders will go live tomorrow.
There will be other stores with stock/preorders open as well so we'll keep you posted.
Fast! Awesome, looking forward :thumb:
Post by: clasicks on Tue, 23 October 2018, 08:26:14
Will there be a version with ISO and split shift? :D
The GK64 already exists for 60% with arrows so I don't think we'll do split right shift :/In for HHKB.
[attachimg=1]
So close, i thought this was going to be my first hotswap pcb to play around with... Any chance you could add in pads for 2U backspace?
Post by: Hund on Tue, 23 October 2018, 09:07:55
Will there be a version with ISO and split shift? :D
The GK64 already exists for 60% with arrows so I don't think we'll do split right shift :/In for HHKB.
(Attachment Link)
So close, i thought this was going to be my first hotswap pcb to play around with... Any chance you could add in pads for 2U backspace?
The HHKB layout is designed to have the backspace on the 1.5U Key on row 3 where you have `|` and `\` on regular ANSI keyboards.
Post by: clasicks on Tue, 23 October 2018, 09:20:53
Will there be a version with ISO and split shift? :D
The GK64 already exists for 60% with arrows so I don't think we'll do split right shift :/In for HHKB.
(Attachment Link)
So close, i thought this was going to be my first hotswap pcb to play around with... Any chance you could add in pads for 2U backspace?
The HHKB layout is designed to have the backspace on the 1.5U Key on row 3 where you have `|` and `\` on regular ANSI keyboards.
Correct, was just inputting my personal preference.
Post by: Hund on Tue, 23 October 2018, 10:16:38
HS60 V2 preorders will go live tomorrow.
There will be other stores with stock/preorders open as well so we'll keep you posted.
Did you find a new manufacturer or is it the same one as last time?
Post by: Mechboards on Tue, 23 October 2018, 12:23:07
HS60 V2 preorders will go live tomorrow.
There will be other stores with stock/preorders open as well so we'll keep you posted.
Did you find a new manufacturer or is it the same one as last time?
New manufacturer and QA process.
Post by: Hund on Tue, 23 October 2018, 17:46:11
HS60 V2 preorders will go live tomorrow.
There will be other stores with stock/preorders open as well so we'll keep you posted.
Did you find a new manufacturer or is it the same one as last time?
New manufacturer and QA process.
That sounds reassuring. :) I'm very exited!
Post by: Mechboards on Wed, 24 October 2018, 05:56:01
Exclusive Hotswappable SMD RGB LED 60% Keyboard in ANSI, ISO, or HHKB. Supports QMK. Developed in partnership with Yiancar
Fits all standard and aftermarket 60% cases.
SEE MORE FOR FAQ’S
The PCB is compatible with QMK firmware. The PCB will ship fully complete, with all components in place.
V2 will include an ARM processor, and Matte Black finish.
This preorder will run for 2 weeks. Looking at delivery 8 weeks from now (18-25th Dec)
Ordering from Australia/NZ? – PREORDER FROM DAILYCLACK
Ordering from Canada? – PREORDER FROM MECHKEYS.CA (https://mechkeys.ca/products/hs60-pcb-gb)
Ordering from the US? – PREORDER LINK SOON
Did you order the V1? Get £15 off when ordering by entering your OLD order number in the notes section. We’ll then manually apply the discount after purchase. Order must be placed through Mechboards.co.uk
V1 -
Fits all standard and aftermarket 60% cases.
SEE MORE FOR FAQ’S
The PCB is compatible with QMK firmware. The PCB will ship fully complete, with all components in place.
V2 will include an ARM processor, and Matte Black finish.
This preorder will run for 2 weeks. Looking at delivery 8 weeks from now (18-25th Dec)
Ordering from Australia/NZ? – PREORDER FROM DAILYCLACK
Ordering from Canada? – PREORDER FROM MECHKEYS.CA (https://mechkeys.ca/products/hs60-pcb-gb)
Ordering from the US? – PREORDER LINK SOON
Did you order the V1? Get £15 off when ordering by entering your OLD order number in the notes section. We’ll then manually apply the discount after purchase. Order must be placed through Mechboards.co.uk
More
Q1: What about other layouts?
A1: We now have ANSI, ISO, HHKB layouts. We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector following the universal GH60 standard. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already. There are exposed pins to add underglow RGB strips, but this is experimental and up to the user.
Q4: Can I set the RGB?
A4: Yes! It comes with different styles as well as colour picker. QMK community is working toward a hosted software to do that as well but its still under development.
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
A1: We now have ANSI, ISO, HHKB layouts. We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector following the universal GH60 standard. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already. There are exposed pins to add underglow RGB strips, but this is experimental and up to the user.
Q4: Can I set the RGB?
A4: Yes! It comes with different styles as well as colour picker. QMK community is working toward a hosted software to do that as well but its still under development.
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
V1 -
More
Hotswap 60% in standard ANSI or ISO layouts. Fully soldered PCB with in-switch SMD RGB LED's, which fits all standard 60% cases and plates.
White PCB. Designed and assembled in the UK. QMK Support.
GB will run for 3 weeks (End 27th April) and looking to ship 2-3 weeks after for mid May release
[attachimg=2]
[attachimg=3]
2 versions:
ANSI in standard 60% layout
ISO in standard 60% layout
£50 for Group Buy, £65 after (plus shipping) - NEWS - We now have an NA proxy! thekey.company will be handling all orders to North America. Therefore I will be refunding shipping (besides £2.50 to cover my shipping to TKC) in due course and then TKC will send a separate invoice prior to final shipment. This will lower the shipping costs considerably.
https://mechboards.co.uk/shop/parts/hs60-pcb/
This will first be a GB and then stocked all the time at Mechboards.co.uk
We're also looking for non-EU stockists!
More images and details soon
FAQ
White PCB. Designed and assembled in the UK. QMK Support.
GB will run for 3 weeks (End 27th April) and looking to ship 2-3 weeks after for mid May release
[attachimg=2]
[attachimg=3]
2 versions:
ANSI in standard 60% layout
ISO in standard 60% layout
£50 for Group Buy, £65 after (plus shipping) - NEWS - We now have an NA proxy! thekey.company will be handling all orders to North America. Therefore I will be refunding shipping (besides £2.50 to cover my shipping to TKC) in due course and then TKC will send a separate invoice prior to final shipment. This will lower the shipping costs considerably.
https://mechboards.co.uk/shop/parts/hs60-pcb/
This will first be a GB and then stocked all the time at Mechboards.co.uk
We're also looking for non-EU stockists!
More images and details soon
FAQ
More
Q1: What about split shift/split backspace/other layouts?
A1: We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
A1: We’re sticking with standard layouts for now, as we can’t add multiple layouts to the same PCB as the hotswap sockets can’t overlap. Trying to cover all possible layouts would be impossible so it’s standard for now. if there are enough people wanting other layouts, we may look into them.
Q2: What happened to the upside down esc and 1 keys?
A2: It’s due to the placement of the USB connector. The hotswap sockets can’t fit otherwise!
Q3: Is it difficult to collect all the parts needed for a full keyboard and to put it together using this PCB?
A3: Any other 60% case you find that has standard mount holes, and any standard plate, will work with this PCB
Q4: Does it have underglow?
A4: No as the power draw for all the in-switch LED’s is quite high already
Q5: USB-C? or Mini
A5: Mini for now
Q6: Do i need diodes, resistors, etc?
A6: The board is fully complete and ready to go!
Post by: Hund on Wed, 24 October 2018, 06:10:00
Post by: Mechboards on Wed, 24 October 2018, 06:13:47
Well, you wasn't kidding with tthe HHKB. I assumed it was the HHKB with 7U spacebar and not the original. This means that wwe have to buy the one case available for it or manufacture something yourself. No buy for me then. :(It's 7u. My KLE layout picture is incorrect. I'll get that fixed.
Sent from my F5121 using Tapatalk
Post by: Hund on Wed, 24 October 2018, 09:13:15
Well, you wasn't kidding with tthe HHKB. I assumed it was the HHKB with 7U spacebar and not the original. This means that wwe have to buy the one case available for it or manufacture something yourself. No buy for me then. :(It's 7u. My KLE layout picture is incorrect. I'll get that fixed.
Sent from my F5121 using Tapatalk
That's great! :)
Post by: Mechboards on Wed, 24 October 2018, 10:26:01
Ordering from Australia/NZ? - https://dailyclack.com/collections/products/products/hs60-pcb - PREORDER FROM DAILYCLACK
Ordering from Canada? - https://mechkeys.ca/products/hs60-pcb-gb - PREORDER FROM MECHKEYS.CA
Ordering from the US? - https://dixiemech.squarespace.com/shop/hs60/ - PREORDER FROM DIXIEMECH
Post by: enrique.aliaga on Wed, 24 October 2018, 12:45:15
I joined Round 1, and I’m hoping such a layout will be available in Round 3 so I can get a second PCB.
Good luck with Round 2!
Sent from my iPhone using Tapatalk
Post by: pixelpusher on Wed, 24 October 2018, 13:34:35
Post by: pixelpusher on Wed, 31 October 2018, 00:53:55
So is there no way to get the R1 discount when ordering through Dixiemech?
Anybody? Anybody? Beuller?
Post by: Mechboards on Wed, 31 October 2018, 05:41:50
So is there no way to get the R1 discount when ordering through Dixiemech?
Anybody? Anybody? Beuller?
No, but the PCB's are roughly priced the same. If you order through us I'll make sure it's the same price.
Post by: Darknight00z on Mon, 05 November 2018, 15:20:51
Post by: AlcoholEnthusiast on Mon, 05 November 2018, 16:50:51
Post by: enrique.aliaga on Wed, 07 November 2018, 07:42:44
I bought one PCB from R1 and it works great with a fixed ANSI aluminum plate.
Sent from my iPhone using Tapatalk
Post by: Mechboards on Thu, 08 November 2018, 08:30:35
Does this PCB have any problems when paired with Universal plates?
I bought one PCB from R1 and it works great with a fixed ANSI aluminum plate.
Sent from my iPhone using Tapatalk
It shouldn't have any issues and I've heard no issues from R1 customers.
Pre Orders have finished but you can still order the HS60 from our website.
Post by: enrique.aliaga on Thu, 08 November 2018, 09:08:20
Pre Orders have finished but you can still order the HS60 from our website.
Oh noes! Can I still get the 15-pound discount as a R1 supporter?
Post by: Mechboards on Thu, 08 November 2018, 10:23:32
Pre Orders have finished but you can still order the HS60 from our website.
Oh noes! Can I still get the 15-pound discount as a R1 supporter?
Yep! Just put your order number in the notes section when you purchase :)
Post by: menuhin on Thu, 08 November 2018, 16:23:56
Different sites are posting different images and it has been confusing.
Post by: comdata55 on Mon, 03 December 2018, 20:29:45
Post by: Mechboards on Wed, 05 December 2018, 13:14:54
anyone order any extra one? I missed out on the GB :(
The preorders are still live on the site.
Post by: Darknight00z on Thu, 03 January 2019, 15:47:12
Post by: Mechboards on Fri, 04 January 2019, 08:04:43
Post by: clik_clak on Fri, 04 January 2019, 08:21:13
The PCB's are now in the UK going through testing and will be sent out soon after that :)
Do you happen to know if Dixie Mech is going to have extras for the US, or am I better off ordering from the UK?
Post by: Darknight00z on Sun, 13 January 2019, 11:12:21
The PCB's are now in the UK going through testing and will be sent out soon after that :)
Do you happen to know if Dixie Mech is going to have extras for the US, or am I better off ordering from the UK?
You can email Dixie Mech to ask?
Post by: audax989 on Sun, 13 January 2019, 17:00:25
Post by: 112227 on Thu, 24 January 2019, 19:00:06
Post by: anon23 on Thu, 24 January 2019, 23:29:03
Quote
These will be released periodically in batches of 10. 18th Jan – Waiting on custom boxes. Will send after that (hopefully a week or so)
So hopefully the first batch should be going out soon?
Post by: MrFurrior on Fri, 25 January 2019, 15:00:19
Post by: rudeboy on Sun, 27 January 2019, 07:08:20
Post by: RETURNISO on Sun, 27 January 2019, 10:18:54
This looks amazing, I love it!
Noob here: Are these still available for purchase? Does this PCB support all key switches or do switches have universal pin layouts. And last what kind of connection does this support? (USB-C, mini, etc.) also what else would I need to buy aside from a case, plate, switches and key caps? Thanks!
PCB support all MX switches on the market. The PCB uses a Mini USB connection.
Your are right, you will need a Case + Plate + Switches + keycaps that support MX switches, you can get what you need on the mechboards site. :)
Post by: Darknight00z on Thu, 31 January 2019, 14:51:13
Quote
Hey all,
I’m sure you’re all super eager to get your HS60. Believe me, I’m trying to get them to you as soon as possible! Sadly my UK supplier of boxes (who said they would be quicker than overseas) have now stated they will ship my delivery of HS60 boxes in the middle of next week – 3 weeks late. I’m just as annoyed as you. Once I get these boxes I will be packing HS60’s LITERALLY ALL DAY until they’re all packed and on their way.
Thanks for being patient.
PS – this is an email to all HS60 purchasers – if you have been refunded you will still receive this email.
Cheers
David
Post by: Mechboards on Thu, 31 January 2019, 16:06:38
Email update from mechboards Jan 31
Thanks for posting - forgot to post here
Post by: GoatMaster on Fri, 01 February 2019, 08:35:12
Post by: Mechboards on Fri, 01 February 2019, 08:50:47
I didn't get the mail even I joined the gb. Is this a bad sign?
Just PM your order number and I'll check :)
Post by: ctrl on Mon, 04 February 2019, 05:01:31
Any extras available or anyone willing to sell? Or is there a v3 on the horizon?
Post by: Mechboards on Mon, 04 February 2019, 05:10:59
Late to the game. Would be great to get hold of a ISO v2 PCB. I believe this is the only hotswappable ISO available on the market...
Any extras available or anyone willing to sell? Or is there a v3 on the horizon?
There will be extras released sporadically on the main website until we get all previous orders posted.
Post by: ctrl on Mon, 04 February 2019, 06:16:29
Late to the game. Would be great to get hold of a ISO v2 PCB. I believe this is the only hotswappable ISO available on the market...
Any extras available or anyone willing to sell? Or is there a v3 on the horizon?
There will be extras released sporadically on the main website until we get all previous orders posted.
Great! Thanks for letting me know. Signed up for notifications. Hope it'll become available. :)
Post by: Mechboards on Tue, 05 February 2019, 03:19:05
Post by: RETURNISO on Tue, 05 February 2019, 04:43:21
HS60's are starting to head out. Look out for your shipment emails.
:eek:
Post by: Mechboards on Thu, 14 February 2019, 06:52:24
Post by: GoatMaster on Thu, 14 February 2019, 07:40:09
Post by: ctrl on Tue, 19 February 2019, 05:29:02
Late to the game. Would be great to get hold of a ISO v2 PCB. I believe this is the only hotswappable ISO available on the market...
Any extras available or anyone willing to sell? Or is there a v3 on the horizon?
There will be extras released sporadically on the main website until we get all previous orders posted.
Happy to follow up and say that I scored one of the last remaining HS60 ISO layout PCBs. :thumb:
(As of now ANSI and HHKB PCBs are out of stock and there's only 3 remaining ISO PCBs.)
Post by: Agpatel on Wed, 20 February 2019, 07:36:34
Post by: Mechboards on Wed, 20 February 2019, 07:39:35
Got notification mine has shipped - when will tracking numbers be sent out (US delivery) - ordered from your site.Please email us and we'll get it to you
Sent from my F5121 using Tapatalk
Post by: txeni on Fri, 22 February 2019, 12:19:02
Got my new HS60 v2 :thumb:
I was starting to play with it to test it however when I tried to program it with the QMK configurator (https://config.qmk.fm/#/hs60/v2/LAYOUT_60_ansi)
I noticed the resulting "firmware" file is a ".bin" instead of a ".hex" like in my HS60 v1.
My question is can I still flash it with my usual "dfu-programer atmega32u4..."?
Or does it has a different micro and you have to program it in a different way?
Post by: txeni on Sat, 23 February 2019, 05:30:30
However I still cannot flash it.
QMK Tools doesn't detect it and "dfu-util" doesn't work for me either...
Anyone got it working and can help me?
Post by: pixelpusher on Sat, 23 February 2019, 09:58:53
Post by: clik_clak on Sat, 23 February 2019, 10:10:29
I bought one from Novelkeys, but it won’t be here until next week. I’d help if I could. I’m interested in seeing what the issue is.
Is NK selling them a new thing? I hope so, I'll be pretty bummed if he's been offering these for months and I spent $30 to have one shipped from the UK
Post by: pixelpusher on Sat, 23 February 2019, 12:08:50
I bought one from Novelkeys, but it won’t be here until next week. I’d help if I could. I’m interested in seeing what the issue is.
Is NK selling them a new thing? I hope so, I'll be pretty bummed if he's been offering these for months and I spent $30 to have one shipped from the UK
They put extras up for sale yesterday. Hhkb were sold out quickly
Post by: MTXjunkie on Sat, 23 February 2019, 12:50:35
I bought one from Novelkeys, but it won’t be here until next week. I’d help if I could. I’m interested in seeing what the issue is.
Is NK selling them a new thing? I hope so, I'll be pretty bummed if he's been offering these for months and I spent $30 to have one shipped from the UK
my shipping was 7 pounds to the US. I think it was $97 total to buy and have it shipped to the US. Sent from my iPhone using Tapatalk Pro
Post by: forumusername on Sat, 23 February 2019, 14:30:17
Post by: RETURNISO on Sat, 23 February 2019, 14:50:21
anyone know if this would work with the qxp?
If the qxp is gh60 compat then it's should work :thumb:
Post by: Mechboards on Sat, 23 February 2019, 15:21:41
Sent from my F5121 using Tapatalk
Post by: babyphil on Sat, 23 February 2019, 17:05:53
anyone know if this would work with the qxp?Round 1 works with QXP.
Post by: pixelpusher on Thu, 28 February 2019, 22:11:27
However, I do have an issue on both boards that seems to come and go. When I first got both of them, the ESC key was mapped to a hex of some sort. I can't remember it now and I've fixed it, but it showed up in VIA as something like Ex21E4. Again, it wasn't exactly that.
Anywhoo, I just remapped it to Escape. However, it seems to come back occasionally, just in the middle of a typing session. Escape will no longer work and when I load up VIA again, that hex code is there instead of escape.
I'll keep an eye on it and see how often it continues to happen. But, does anyone else have this issue?
Post by: pixelpusher on Fri, 01 March 2019, 01:29:51
If you use the MO(1) key and either EF- or EF+ it sets the Esc key to 0x3c29
Actually, I have found that any time you chage lighting effects, the Esc key resets to this value (which does nothing in windows).
Any ideas what is going on?
Post by: Mechboards on Fri, 01 March 2019, 02:54:20
Figured out what causes it.
If you use the MO(1) key and either EF- or EF+ it sets the Esc key to 0x3c29
Actually, I have found that any time you chage lighting effects, the Esc key resets to this value (which does nothing in windows).
Any ideas what is going on?
You'll be able to fix this by following the TO FLASH instructions and updating the PCB.
To Flash:
Unplug
Hold Escape
Plug In
Flash using QMK Toolbox
Post by: pixelpusher on Fri, 01 March 2019, 10:39:27
This discussion is also happening on keebtalk: https://www.keebtalk.com/t/struggling-to-flash-hs60-v2-with-arm-stm32f303cc/5063
At this point my PCB is unusable :(
Keep in mind, the HS60v2 stuff doesn't work in qmk toolbox. The board is listed, but the compiled defaults are not on the repo, so you can't use it. Also, the .bin files listed on mechboards do not work on these PCBs.
I set up an environment to compile it myself on windows. As discussed on Keebtalk, you have to pass additional arguments for dfu, or do the build and flash in one step.
I tried the build and flash, passing make hs60/v2:ansi:dfu-util
Build seem to go, .hex was created but an error (probably because I don't think I had it it flashing mode) and qmk toolbox said "invalid dfu suffix signature"
Flashed the .build/hs60_v2_ansi.hex onto the PCB, which apparently was a bad decision.
Now I can't use it at all. Mac doesn't see it. Windows says USB malfunction.
I tried to reset but (hold esc, plug, unplug, release esc) but windows just sees it as a malfunctioning USB device. Idears?
Post by: 112227 on Fri, 01 March 2019, 10:43:43
Post by: pixelpusher on Fri, 01 March 2019, 11:05:10
I used the VIA configurator...way too easy not to.
The problem is the firmware loaded on the board is not updated. So, VIA works great, but, when you change the RGB mode on the board, the Esc key turns into a weird keyboard scan code that doesn't work. So, each time you change the RGB mode, you have to go back into VIA and set the 0x3c29 back to Esc. I got two PCBs from the Novelkeys extra sale. I don't know if the same firmware was on all of the PCBs, but the behavior was the same on both of the boards I recieved.
I think I got it working on my other PCB by compiling my own firmware and adding the additional dfu arguments, but the first one is bricked.
Post by: pixelpusher on Fri, 01 March 2019, 11:26:41
Post by: ryancopenhaver on Tue, 05 March 2019, 22:21:00
I want to use VIA, but it doesn't have a lot of capabilities I need for this PCB, and it only has 3 layers on VIA?
Anyways, I keep trying to flash it and I keep getting an error stating "Cannot open DFU device 0483:df11 No DFU capable USB device available."
I have purchased two of these PCBs: One through mechboards and another through NovelKeys, and both are having this issue.
Is there something that I'm missing? I even went to the Keebtalk discussion and went through dfu-util with the posted arguments and still getting this error. I have also attempted flashing through QMK Toolbox as well as the command line. Any help with this would be greatly appreciated.
Post by: pixelpusher on Tue, 05 March 2019, 22:37:28
I am having the worst time trying to flash my firmware on this thing.
I want to use VIA, but it doesn't have a lot of capabilities I need for this PCB, and it only has 3 layers on VIA?
Anyways, I keep trying to flash it and I keep getting an error stating "Cannot open DFU device 0483:df11 No DFU capable USB device available."
I have purchased two of these PCBs: One through mechboards and another through NovelKeys, and both are having this issue.
Is there something that I'm missing? I even went to the Keebtalk discussion and went through dfu-util with the posted arguments and still getting this error. I have also attempted flashing through QMK Toolbox as well as the command line. Any help with this would be greatly appreciated.
Are you hitting the button on the back before you flash it? Either that or hold esc while you plug it in?
Post by: ryancopenhaver on Wed, 06 March 2019, 04:36:12
Yep, tried just about every combination on this thing. Kept following the instructions to RESET/FLASH by holding Esc while unplugged, then plugging in while holding Esc still to flash the PCB. Also tried holding the physical button on the back to flash, and even used Fn +] for the RESET mapping from the layout that I can get in VIA. No success on any of those.I am having the worst time trying to flash my firmware on this thing.
I want to use VIA, but it doesn't have a lot of capabilities I need for this PCB, and it only has 3 layers on VIA?
Anyways, I keep trying to flash it and I keep getting an error stating "Cannot open DFU device 0483:df11 No DFU capable USB device available."
I have purchased two of these PCBs: One through mechboards and another through NovelKeys, and both are having this issue.
Is there something that I'm missing? I even went to the Keebtalk discussion and went through dfu-util with the posted arguments and still getting this error. I have also attempted flashing through QMK Toolbox as well as the command line. Any help with this would be greatly appreciated.
Are you hitting the button on the back before you flash it? Either that or hold esc while you plug it in?
The weird thing is that when QMK Toolbox is running, it lists the PCB being in DFU mode. However, dfu-util - - list states that no DFU devices were found. Attempting to flash both ways shows the error above.
Normally, I'm pretty good with this stuff, but this one has me stumped. I've got $200 in PCBs that I can't use
Sent from my SM-G965U using Tapatalk
Post by: Mechboards on Wed, 06 March 2019, 04:50:28
Yep, tried just about every combination on this thing. Kept following the instructions to RESET/FLASH by holding Esc while unplugged, then plugging in while holding Esc still to flash the PCB. Also tried holding the physical button on the back to flash, and even used Fn +] for the RESET mapping from the layout that I can get in VIA. No success on any of those.I am having the worst time trying to flash my firmware on this thing.
I want to use VIA, but it doesn't have a lot of capabilities I need for this PCB, and it only has 3 layers on VIA?
Anyways, I keep trying to flash it and I keep getting an error stating "Cannot open DFU device 0483:df11 No DFU capable USB device available."
I have purchased two of these PCBs: One through mechboards and another through NovelKeys, and both are having this issue.
Is there something that I'm missing? I even went to the Keebtalk discussion and went through dfu-util with the posted arguments and still getting this error. I have also attempted flashing through QMK Toolbox as well as the command line. Any help with this would be greatly appreciated.
Are you hitting the button on the back before you flash it? Either that or hold esc while you plug it in?
The weird thing is that when QMK Toolbox is running, it lists the PCB being in DFU mode. However, dfu-util - - list states that no DFU devices were found. Attempting to flash both ways shows the error above.
Normally, I'm pretty good with this stuff, but this one has me stumped. I've got $200 in PCBs that I can't use
Sent from my SM-G965U using Tapatalk
Hey Ryan, try this:
firstly download https://zadig.akeo.ie/
then put the keyboard in flashing mode
esc+usb thing
open zadig
from devices select STM32 BOOTLOADER
from driver select libusbK
press reinstall driver
let it do its thing
now qmk toolbox should work as expected
This is an issue with windows 10 installing a slightly different variant of the libusb driver, literally by random chance
some pcs work straight away some don't
Post by: ryancopenhaver on Wed, 06 March 2019, 21:44:43
Brilliant...it works! I have successfully flashed on both PCBs with this solution.Yep, tried just about every combination on this thing. Kept following the instructions to RESET/FLASH by holding Esc while unplugged, then plugging in while holding Esc still to flash the PCB. Also tried holding the physical button on the back to flash, and even used Fn +] for the RESET mapping from the layout that I can get in VIA. No success on any of those.I am having the worst time trying to flash my firmware on this thing.
I want to use VIA, but it doesn't have a lot of capabilities I need for this PCB, and it only has 3 layers on VIA?
Anyways, I keep trying to flash it and I keep getting an error stating "Cannot open DFU device 0483:df11 No DFU capable USB device available."
I have purchased two of these PCBs: One through mechboards and another through NovelKeys, and both are having this issue.
Is there something that I'm missing? I even went to the Keebtalk discussion and went through dfu-util with the posted arguments and still getting this error. I have also attempted flashing through QMK Toolbox as well as the command line. Any help with this would be greatly appreciated.
Are you hitting the button on the back before you flash it? Either that or hold esc while you plug it in?
The weird thing is that when QMK Toolbox is running, it lists the PCB being in DFU mode. However, dfu-util - - list states that no DFU devices were found. Attempting to flash both ways shows the error above.
Normally, I'm pretty good with this stuff, but this one has me stumped. I've got $200 in PCBs that I can't use
Sent from my SM-G965U using Tapatalk
Hey Ryan, try this:
firstly download https://zadig.akeo.ie/
then put the keyboard in flashing mode
esc+usb thing
open zadig
from devices select STM32 BOOTLOADER
from driver select libusbK
press reinstall driver
let it do its thing
now qmk toolbox should work as expected
This is an issue with windows 10 installing a slightly different variant of the libusb driver, literally by random chance
some pcs work straight away some don't
It is always a driver issue for me. I should know this by now, but I greatly appreciate the both of you for reaching out and helping.
Thank you so much for solving my problem!
Sent from my SM-G965U using Tapatalk
Post by: GoatMaster on Thu, 28 March 2019, 07:34:13
I found the option in the qmk firmware documentation but I don't know where to set it.
https://docs.qmk.fm/#/feature_backlight?id=configuration
Post by: stanrc on Thu, 28 March 2019, 08:33:03
Post by: GoatMaster on Thu, 28 March 2019, 09:38:26
The only way right now is to hardcode in the zeal60/rgb_backlight.c file. You can see the way I did it here: https://github.com/stanrc85/qmk_firmware/blob/72252a2051e8a756487419b4aeb6ebaa1edc3299/keyboards/zeal60/rgb_backlight.c#L77
Thank you. I than have to compile the firmware by myself?
Post by: stanrc on Thu, 28 March 2019, 10:50:25
Post by: Cee on Mon, 01 April 2019, 10:54:39
Post by: Mechboards on Mon, 01 April 2019, 19:03:57
Trying to find an ANSI board. Will they ever go back in stock?
Check NovelKeys. We will be ordering more in the next couple of months with small changes (USB-C, glued connector, for example)
Post by: enrique.aliaga on Mon, 01 April 2019, 19:49:32
Sent from my iPhone using Tapatalk
Post by: ptiede on Mon, 01 April 2019, 20:07:25
Post by: Mechboards on Tue, 02 April 2019, 04:18:28
I ordered an HHKB HS60 from mechkeys.ca and still haven't received my board. I tried to private message you and mechkeys.ca and haven't gotten a reply yet. Where should I try to contact you to give my order number and such?
Hmm that's weird - I haven't received any PM's from you that i can see. Email us at info@mechboards.co.uk and we'll try and sort it.
Cheers
Post by: GoatMaster on Tue, 02 April 2019, 07:28:24
Yeah unfortunately. After that you could go back to using VIA since that won't affect it.
Is it possible to make the settings with help of this website?
https://kbfirmware.com/
Post by: stanrc on Tue, 02 April 2019, 07:34:08
Yeah unfortunately. After that you could go back to using VIA since that won't affect it.
Is it possible to make the settings with help of this website?
https://kbfirmware.com/
No, I don't believe so. That version of QMK is a few years out of date anyways. I could send you a bin file of the default keymap with the RGB changes you want and then you can use VIA to adjust the keymap easily.
Post by: GoatMaster on Tue, 02 April 2019, 07:53:12
Yeah unfortunately. After that you could go back to using VIA since that won't affect it.
Is it possible to make the settings with help of this website?
https://kbfirmware.com/
No, I don't believe so. That version of QMK is a few years out of date anyways. I could send you a bin file of the default keymap with the RGB changes you want and then you can use VIA to adjust the keymap easily.
This would be nice! Thank you.
Post by: stanrc on Tue, 02 April 2019, 08:21:43
Yeah unfortunately. After that you could go back to using VIA since that won't affect it.
Is it possible to make the settings with help of this website?
https://kbfirmware.com/
No, I don't believe so. That version of QMK is a few years out of date anyways. I could send you a bin file of the default keymap with the RGB changes you want and then you can use VIA to adjust the keymap easily.
This would be nice! Thank you.
Pm'ed
Post by: FearsomeCubedWarrior on Wed, 08 May 2019, 04:39:11
Post by: Mechboards on Wed, 08 May 2019, 04:54:59
Is there any hope for next run?
Getting more ANSI/HHKB sorted at the moment. Hopefully next month sometime.
Post by: FearsomeCubedWarrior on Wed, 08 May 2019, 07:54:41
Post by: enrique.aliaga on Wed, 08 May 2019, 08:37:49
Sent from my iPhone using Tapatalk
Post by: pixelpusher on Wed, 08 May 2019, 09:17:01
Is there any hope for next run?
Getting more ANSI/HHKB sorted at the moment. Hopefully next month sometime.
Glad to hear it. I have 2 and I'm interested in picking up a third!
Post by: audax989 on Thu, 09 May 2019, 17:02:56
Post by: enrique.aliaga on Thu, 09 May 2019, 17:08:29
one of my led's doesn't do the RED color anymore. any tips on how I can fix it?
Reach out to Yiancar on Mechboards’ Discord.
Sent from my iPhone using Tapatalk
Post by: clik_clak on Mon, 10 June 2019, 15:37:50
Post by: pixelpusher on Mon, 10 June 2019, 16:56:23
Can anyone tell me how I'm supposed to save changes through the VIA configurator and save the keymap? I can change LED settings and save them and then unplug the keyboard and those are saved, but it never saves my keymap changes. All I want to do is set my esc key to actually function like an escape key.
Sounds like the same issue I was having. You'll need to press the button on the back of the board and flash updated firmware.
The bin files are on this page to get it updated.
https://mechboards.co.uk/info-hs60/
Post by: clik_clak on Mon, 10 June 2019, 17:16:50
Can anyone tell me how I'm supposed to save changes through the VIA configurator and save the keymap? I can change LED settings and save them and then unplug the keyboard and those are saved, but it never saves my keymap changes. All I want to do is set my esc key to actually function like an escape key.
Sounds like the same issue I was having. You'll need to press the button on the back of the board and flash updated firmware.
The bin files are on this page to get it updated.
https://mechboards.co.uk/info-hs60/
Thanks for the help! I ended up flashing it through QMK and that worked fine. Nice to have a functioning board that's fully usable now!
Post by: GoatMaster on Thu, 31 October 2019, 09:29:56
When I now screw down the pcb to the case I have the problem that for example the spacebar is not working and also some other keys like 'f' 'g' and 'h'.
Also randomly some hex codes where printed if I use the control key on the left side.
Anyone with the same problem and a fix for me?
Post by: pixelpusher on Thu, 31 October 2019, 09:41:02
I newley use a alu case with the pcb before I used an acrylic case.
When I now screw down the pcb to the case I have the problem that for example the spacebar is not working and also some other keys like 'f' 'g' and 'h'.
Also randomly some hex codes where printed if I use the control key on the left side.
Anyone with the same problem and a fix for me?
You have a hotswap socket hitting one of the screw posts on the case. Most likely the middle one or the one to the right of the space bar. Cover those sections with some electrical tape before you screw it down.
Post by: Wickles on Thu, 31 October 2019, 13:42:33
I newley use a alu case with the pcb before I used an acrylic case.
When I now screw down the pcb to the case I have the problem that for example the spacebar is not working and also some other keys like 'f' 'g' and 'h'.
Also randomly some hex codes where printed if I use the control key on the left side.
Anyone with the same problem and a fix for me?
You have a hotswap socket hitting one of the screw posts on the case. Most likely the middle one or the one to the right of the space bar. Cover those sections with some electrical tape before you screw it down.
I had the same issue when I bought the V2 a while back. I ended up loosening the screws and everything worked perfectly so didn't need to use electrical tape.
Post by: GoatMaster on Tue, 12 November 2019, 09:39:23
I newley use a alu case with the pcb before I used an acrylic case.
When I now screw down the pcb to the case I have the problem that for example the spacebar is not working and also some other keys like 'f' 'g' and 'h'.
Also randomly some hex codes where printed if I use the control key on the left side.
Anyone with the same problem and a fix for me?
Now the y, h, b and space key stopped completely working for me. Even when they are not in a case. I can not find anything on the back of the pcb that looks bad.
Any idea hot to fix this? I have already reset the pcb.
Post by: pixelpusher on Tue, 12 November 2019, 10:30:38
I newley use a alu case with the pcb before I used an acrylic case.
When I now screw down the pcb to the case I have the problem that for example the spacebar is not working and also some other keys like 'f' 'g' and 'h'.
Also randomly some hex codes where printed if I use the control key on the left side.
Anyone with the same problem and a fix for me?
Now the y, h, b and space key stopped completely working for me. Even when they are not in a case. I can not find anything on the back of the pcb that looks bad.
Any idea hot to fix this? I have already reset the pcb.
Diode out perhaps? Can you attach a close up photo of the area?
Post by: GoatMaster on Fri, 15 November 2019, 02:07:19
I newley use a alu case with the pcb before I used an acrylic case.
When I now screw down the pcb to the case I have the problem that for example the spacebar is not working and also some other keys like 'f' 'g' and 'h'.
Also randomly some hex codes where printed if I use the control key on the left side.
Anyone with the same problem and a fix for me?
Now the y, h, b and space key stopped completely working for me. Even when they are not in a case. I can not find anything on the back of the pcb that looks bad.
Any idea hot to fix this? I have already reset the pcb.
Diode out perhaps? Can you attach a close up photo of the area?
Sorry for the long response time.
(https://i.imgur.com/8mFHzsD.jpg)
Not working are:
D24
D25
D27
D32
and the one next to the whole for the screw
Post by: pixelpusher on Fri, 15 November 2019, 09:50:51
First, test the sockets. Take the PCB out of the case and connect it to the computer. Use tweezers or something metal like a bent paper clip and bridge the two pads on the back (Orange 1 in photo). Make sure you are connecting the flat pads that are on the PCB, and not just the socket arms. Let us know if that works for any of the switches not functioning. If that's the case, the hotswap sockets have just become desoldered from the pads under them.
Next, I would check the diodes on the board. Connect the Cathode to the lower hotswap arm like the blue #2 in the photo. Does it register? Not sure of the diode polarity, so try a working switch and see what you get. Might need to connect the other end.
Lastly... what is that green 3 pointing to? It looks like it could be a screw that's very close to the processor. Traces run out of that Atmel chip to the board. Could have shorted/scratched something down there??
Start with these and see what you get.
[attachimg=1]
Post by: Cee on Sat, 16 November 2019, 18:38:25
Post by: FearsomeCubedWarrior on Sat, 14 December 2019, 06:08:15
Post by: Mechboards on Mon, 16 December 2019, 08:05:11
Production is ongoing. It was expected to arrive to me around now but we're still a couple weeks away from a delivery. They'll arrive very early in the new year. Sorry about the delays.
Thanks
David
Post by: Mechboards on Sun, 29 December 2019, 08:17:42
Post by: Mechboards on Mon, 06 January 2020, 09:33:44
Post by: dhb82 on Fri, 24 January 2020, 18:35:55
Post by: sako on Sat, 08 February 2020, 07:13:12
I got a HS60 v3 and fried it after less than 3 days because I was using a metal case without proper insulation between standoffs and PCB. The whole 6/Y/H/B/spacebar column was dead. Resetting the board did not help.
I revived it using the following method
Image: https://imgur.com/a/EyW89hc
- Take a multimeter. Looking at the pcb on the bottom side, make sure there is continuity between the RIGHT socket of each key in the dead column and the old pin (3rd pin on the top left of the chip, see image). If there is continuity, it means the pin is fried. If there is no continuity, you have a different issue, like a scratched trace somewhere.
- Solder a short wire from the RIGHT pad of the spacebar socket to the exposed A6 pin hole (see image). Check with the multimeter for continuity between all the RIGHT socket of each key in the dead column to the new pin.
- Using a very sharp xacto cutter VERY CAREFULLY cut the trace from the column to the old pin. This took me a while to find, and I think the best place to cut is (see image) right after the via hole near the spacebar socket. Scratch on top of the trace and expose some of the copper, then test for continuity with the old pin, just to make sure you're cutting the right trace. Then keep going with the cutter until there is no more continuity to the old pin.
- Download the qmk_firmware repo and open this file -> keyboards/hs60/v2/ansi/config.h
- change the line
Code: [Select]
#define MATRIX_COL_PINS { A13, A10, A9, A14, A15, B8, B9, C13, C14, C15, A0, A1, A2, A3 }and change B9 to A6.- Flash firmware on the board. FYI this is done from the root of the qmk_firmware directory and executing "make hs60/v2/ansi:via:dfu-util"
Btw I have the v3 ANSI version. The traces might be different on ISO and HHKB versions
Post by: Actualize on Mon, 10 February 2020, 06:45:14
Post by: deadarsch on Fri, 21 February 2020, 12:05:03
After flashing it on PC with QMK ToolBox it worked, keyboard showed up in device manager as HID device (also after rebooting), as long as I don't pull out the cable and reconnect it, because once the cable is disconnected, it totally disappeared, even booting the PC with the keyboard connected doesn't work.
I think the problem is in windows, but I have no idea what it is.
Post by: pixelpusher on Fri, 21 February 2020, 12:53:58
Hey guys, I am having a weird problem but I don't know what causes it. HS60 V3. I flashed it on my Macbook with QMK ToolBox and it worked flawlessly on MacOS. When the keyboard it connected to my PC, it doesn't even show up in the device manager. (USB cable directly to the back of the motherboard).
After flashing it on PC with QMK ToolBox it worked, keyboard showed up in device manager as HID device (also after rebooting), as long as I don't pull out the cable and reconnect it, because once the cable is disconnected, it totally disappeared, even booting the PC with the keyboard connected doesn't work.
I think the problem is in windows, but I have no idea what it is.
You're going directly into the computer? No usb hub or monitor pass through? I can't tell you how many times I thought I fried a PCB only to find out it was windows deciding not to pass data through one of my hubs. Sometimes they work fine. Sometimes they don't.
Post by: pixelpusher on Fri, 21 February 2020, 13:14:37
https://caniusevia.com/
flash the firmware from here with QMK toolbox:
https://caniusevia.com/docs/download_firmware
Look for your HS60 on the list. I don't know if you use HHKB, ANSI or ISO
Post by: Cee on Sun, 23 February 2020, 20:38:15
Post by: pixelpusher on Sun, 23 February 2020, 21:04:33
Does the HHKB layout support tsangan bottom row?
Certainly appears to. But I'm only going of render photos shown here:
https://dailyclack.com/products/hs60-pcb
[attachimg=1]
Post by: delvix on Wed, 17 February 2021, 09:50:44
Post by: pixelpusher on Wed, 17 February 2021, 10:35:36
Couldn't figure out how to flash my board with QMK like I have done in the past so I downloaded and used VIA for the first time. It's pretty great! A lot simpler to use than QMK. However is it not possible to use the LT() keycode in VIA? Eg. I want my delete key to be delete when tapped but open layer 2 when held. Is that possible in VIA? I can't seem to figure it out.
Go to the "Special" tab and select the "Any" key. This allows you to type in any qmk function on that key.
After you choose "Any" for the delete, you'll have to click on that key in the VIA GUI and type in:
LT(2, KC_DELETE)
You can see I use it for going to layer 1 on hold or caps lock on tap for my layout.
[attachimg=1]
Post by: delvix on Wed, 17 February 2021, 15:24:31
Couldn't figure out how to flash my board with QMK like I have done in the past so I downloaded and used VIA for the first time. It's pretty great! A lot simpler to use than QMK. However is it not possible to use the LT() keycode in VIA? Eg. I want my delete key to be delete when tapped but open layer 2 when held. Is that possible in VIA? I can't seem to figure it out.
Go to the "Special" tab and select the "Any" key. This allows you to type in any qmk function on that key.
After you choose "Any" for the delete, you'll have to click on that key in the VIA GUI and type in:
LT(2, KC_DELETE)
You can see I use it for going to layer 1 on hold or caps lock on tap for my layout.
(Attachment Link)
Ah that worked perfectly thank you so much!
Post by: Mechboards on Tue, 30 March 2021, 19:02:00
Post by: pixelpusher on Tue, 30 March 2021, 19:15:20
Small notice - HS60's will be restocked on the website tomorrow at 11 BST.
Awesome. Thanks for letting us know. :thumb: