For me, the overall height of the case looks a little on the high side, and I can't get by with winkeyless. I also thing the cut-out on the bottom being a different angle from the case top confuses the eye a bit.
I appreciate the clean design, though - doesn't look like a spaceship or the Jetsons' toaster or anything, which is a relief.
Beautiful case, interested in 60% case!
Will there be a brass plate?
Will zeal60 pcb fits in this case?
Looks nice! Interested in the HHKB style case with weight :thumb:
Gesendet von meinem SM-G920F mit Tapatalk
can you show how exactly your plate is meant to mount in the case? from the render angles you can't see it at all
I also have mentioned about the brass weight should be able to see from the bottom of the case which means cut a whole through the case to show off the insert weight, do you think it looks better in that way?
I also have mentioned about the brass weight should be able to see from the bottom of the case which means cut a whole through the case to show off the insert weight, do you think it looks better in that way?
A few people have requested that the weight be on the bottom of the case instead of the inside. There wasn't really a reason for it to be on the inside, that's just the way I designed it. I'll most likely end up changing it to the bottom of the case for the final design.
Great looking case. Would have to use this on an extremely special build.
I also have mentioned about the brass weight should be able to see from the bottom of the case which means cut a whole through the case to show off the insert weight, do you think it looks better in that way?
A few people have requested that the weight be on the bottom of the case instead of the inside. There wasn't really a reason for it to be on the inside, that's just the way I designed it. I'll most likely end up changing it to the bottom of the case for the final design.
For starters, the board is fantastic looking. Please make all 3 versions. This is an instant buy for me.
I do have one selfish request...can Red and Gold be two of the colors you bring us along the basic ones? I just need a red HHKB to stop my searching! Gold is just a pretty bonus.
Also, can anyone tell me why the brass on the bottom is better than inside? Or is it only for the looks? I thought the brass inside would help against vibrations/cause deeper clacks, or was I wrong in assuming that? Honest question, I'm just curious.
Anyway, I'm in. Please just make it asap! Your other model with the simple case would look fantastic with the HHKB and Winkeyless tops too, as it looked like a better version of the FMJ cases!
Edit: Will little indents on the bottom be made for the Rubber feet? If not, is that possible? Also, any chance you'll be able to offer brass, polycarbonate and aluminum plates too? It's a bit much, but if possible it would be amazing!
I am really interested in this. I am not sure which I like more.. the HHKB or the WKL. Looking great!
Very cool, but personally I think it would look better if the bottom of the slant was parallel to the top of the case. Is there any chance that you could do this?
The sides of the case look too flat imo, with the cutout creating a strange overall shape.
With some minor changes this could be awesome tho! =)
Yas 62 top anyone?
When are you planning to run a GB for this? A rough estimation would be great so I can save up for it! :)
Gesendet von meinem SM-G920F mit Tapatalk
I hope the GB will start with in the next 1-2 months
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)
The first one looks the best because there are way too many 60% board looks like the second picture
P/s my wallet is read
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)
What does it look like if you extend the back angle all the way to the back corner?
Yea like he said the in the begining of the topic, he wants something unique that from his own ideas not following the othersThe first one looks the best because there are way too many 60% board looks like the second picture
P/s my wallet is read
I agree with you haha. The first one is my favorite, but I think the second one might give it a run for its money.. We'll see what I end up going with in the long run, but right now my vote is with the first one.Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)
What does it look like if you extend the back angle all the way to the back corner?Show Image(http://i.imgur.com/X5uhsUH.png?1)
I would highly recommend that you make the front of the case 20mm height as an absolute maximum. Trust me - you do not want an inch height at the front. I've been there and it is not comfortable.
Yea like he said the in the begining of the topic, he wants something unique that from his own ideas not following the othersThe first one looks the best because there are way too many 60% board looks like the second picture
P/s my wallet is read
I agree with you haha. The first one is my favorite, but I think the second one might give it a run for its money.. We'll see what I end up going with in the long run, but right now my vote is with the first one.Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)
What does it look like if you extend the back angle all the way to the back corner?Show Image(http://i.imgur.com/X5uhsUH.png?1)
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)Show Image(http://i.imgur.com/9tolxPI.png?1)Show Image(http://i.imgur.com/DWZBffa.png?2)
The first one looks the best because there are way too many 60% board looks like the second picture
P/s my wallet is read
I agree with you haha. The first one is my favorite, but I think the second one might give it a run for its money.. We'll see what I end up going with in the long run, but right now my vote is with the first one.Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)
What does it look like if you extend the back angle all the way to the back corner?Show Image(http://i.imgur.com/X5uhsUH.png?1)
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)Show Image(http://i.imgur.com/9tolxPI.png?1)Show Image(http://i.imgur.com/DWZBffa.png?2)
first design please, too many cases with the second design and it just looks "generic" imo
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)Show Image(http://i.imgur.com/9tolxPI.png?1)Show Image(http://i.imgur.com/DWZBffa.png?2)
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!first design please, too many cases with the second design and it just looks "generic" imoShow Image(http://i.imgur.com/pgqbbqK.png?1)Show Image(http://i.imgur.com/9tolxPI.png?1)Show Image(http://i.imgur.com/DWZBffa.png?2)
Wait, this one is nice too. :'(
I'm too indecisive.
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)Show Image(http://i.imgur.com/9tolxPI.png?1)Show Image(http://i.imgur.com/DWZBffa.png?2)
If you need to go with a cutout I'd prefer the first one, otherwise I'm indifferent between first and second
Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)Show Image(http://i.imgur.com/9tolxPI.png?1)Show Image(http://i.imgur.com/DWZBffa.png?2)
The first one looks the best because there are way too many 60% board looks like the second picture
P/s my wallet is read
I agree with you haha. The first one is my favorite, but I think the second one might give it a run for its money.. We'll see what I end up going with in the long run, but right now my vote is with the first one.Was messing around with the design of the base, does anybody have a preference? They aren't super high quality pictures, but you should be able to get the idea. If you don't like any of these choices, feel free to explain/draw what you think would look good!Show Image(http://i.imgur.com/pgqbbqK.png?1)
What does it look like if you extend the back angle all the way to the back corner?Show Image(http://i.imgur.com/X5uhsUH.png?1)
Will it looks something like this with top aluminum case add on? That would be sickShow Image(https://www.google.com/search?q=hammer+60%25+case&source=lnms&tbm=isch&sa=X&sqi=2&ved=0ahUKEwif48yQ8JDTAhVlhlQKHaQ1DewQ_AUIBygC&biw=1920&bih=922#imgrc=NCxHkstuVe_sPM:)
Will it looks something like this with top aluminum case add on? That would be sickThis is how I saw it when I saw the renders. I even texted a friend and told him it is a mix between the Hammer case and Xondat's X60.Show Image(https://www.google.com/search?q=hammer+60%25+case&source=lnms&tbm=isch&sa=X&sqi=2&ved=0ahUKEwif48yQ8JDTAhVlhlQKHaQ1DewQ_AUIBygC&biw=1920&bih=922#imgrc=NCxHkstuVe_sPM:)
I agree with folks saying cutout makes it somewhat unique and that without it the case would be quite generic.
However, I'd really prefer the metal visible in the cutout. It's difficult for me to explain, but on your initial renders the side of case looked as if it had a hole, not just a cutout, because there was only shadow visible. I know it is just a render, but I'd prefer the cutout to be rather shallow.
I also think the case should not be too high and one inch definitely seems too much for the front.
Correct me if I'm wrong - this case only works with bundled plates, right? I'd love if it worked with YAS62 that I ordered...
Some people like thick in the front tho, do you know how tall is fjell? That case looks pretty tall in the front too and please combine xondat + hammer into this case, that would be awsomeI agree with folks saying cutout makes it somewhat unique and that without it the case would be quite generic.
However, I'd really prefer the metal visible in the cutout. It's difficult for me to explain, but on your initial renders the side of case looked as if it had a hole, not just a cutout, because there was only shadow visible. I know it is just a render, but I'd prefer the cutout to be rather shallow.
I also think the case should not be too high and one inch definitely seems too much for the front.
Correct me if I'm wrong - this case only works with bundled plates, right? I'd love if it worked with YAS62 that I ordered...
Don't worry, the case is still being revised. One inch is too thick, my goal is to bring it down to .75". The cutout should be visible from the side. It's pretty shallow, but my rendering is still not very good, so it made them look all black for some reason. The case will only work with the bundled plate though :(
Some people like thick in the front tho, do you know how tall is fjell? That case looks pretty tall in the front too and please combine xondat + hammer into this case, that would be awsomeI agree with folks saying cutout makes it somewhat unique and that without it the case would be quite generic.
However, I'd really prefer the metal visible in the cutout. It's difficult for me to explain, but on your initial renders the side of case looked as if it had a hole, not just a cutout, because there was only shadow visible. I know it is just a render, but I'd prefer the cutout to be rather shallow.
I also think the case should not be too high and one inch definitely seems too much for the front.
Correct me if I'm wrong - this case only works with bundled plates, right? I'd love if it worked with YAS62 that I ordered...
Don't worry, the case is still being revised. One inch is too thick, my goal is to bring it down to .75". The cutout should be visible from the side. It's pretty shallow, but my rendering is still not very good, so it made them look all black for some reason. The case will only work with the bundled plate though :(
I would be interested in a WKL case. Definitely beats my current method of using PMK blockers.
Plain side would be best imo.
Sound perfect to me, Hammer is my dream case....Some people like thick in the front tho, do you know how tall is fjell? That case looks pretty tall in the front too and please combine xondat + hammer into this case, that would be awsomeI agree with folks saying cutout makes it somewhat unique and that without it the case would be quite generic.
However, I'd really prefer the metal visible in the cutout. It's difficult for me to explain, but on your initial renders the side of case looked as if it had a hole, not just a cutout, because there was only shadow visible. I know it is just a render, but I'd prefer the cutout to be rather shallow.
I also think the case should not be too high and one inch definitely seems too much for the front.
Correct me if I'm wrong - this case only works with bundled plates, right? I'd love if it worked with YAS62 that I ordered...
Don't worry, the case is still being revised. One inch is too thick, my goal is to bring it down to .75". The cutout should be visible from the side. It's pretty shallow, but my rendering is still not very good, so it made them look all black for some reason. The case will only work with the bundled plate though :(
No idea how tall the FJELL is. It looks pretty tall, but I still feel like .75" would be a lot more comfortable than 1". Combining KMAC and Hammer is the goal of this case. I don't want to keep the sides to simple because then it'll just be too boring IMO.I would be interested in a WKL case. Definitely beats my current method of using PMK blockers.
Plain side would be best imo.
Plain side does look clean, but it's too generic for me. Right now, it seem like there's a clean division between clean side and Hammer side. Ideally, there would be the option for two different bottom designs, but I'm not sure if that's possible. If only one design is possible, it will be the Hammer design. More details on what is possible in manufacturing will come later.
I'M KEEPING THE DREAM ALIVE! :'(
Edit: snevok #1!
I'M KEEPING THE DREAM ALIVE! :'(
Edit: snevok #1!
Bless up. It'll come eventually, school has just been pretty busy lately. Will post updates as soon as something worthwhile happens!
Any thoughts/feedback on the new design? Top half and bottom half are different colors to show how the halves fit together, and the light grey parts are acrylic for underglow. I wanted to keep the clean KMAC look, while also keeping the design interesting with some angles. Front has been shortened to 0.75", and the angle has been increased to 7.5 degrees.Show Image(http://i.imgur.com/4P3S1Ri.png)
Any thoughts/feedback on the new design? Top half and bottom half are different colors to show how the halves fit together, and the light grey parts are acrylic for underglow. I wanted to keep the clean KMAC look, while also keeping the design interesting with some angles. Front has been shortened to 0.75", and the angle has been increased to 7.5 degrees.Show Image(http://i.imgur.com/4P3S1Ri.png)
Sheeeesh, looks nice!
Is it possible to use with the acrylic as well? (I'm guessing not due to the design, but still curious!)
Any thoughts/feedback on the new design? Top half and bottom half are different colors to show how the halves fit together, and the light grey parts are acrylic for underglow. I wanted to keep the clean KMAC look, while also keeping the design interesting with some angles. Front has been shortened to 0.75", and the angle has been increased to 7.5 degrees.Show Image(http://i.imgur.com/4P3S1Ri.png)
Sheeeesh, looks nice!
Is it possible to use with the acrylic as well? (I'm guessing not due to the design, but still curious!)
Not really sure I understand your question 100%, but I should've made this more clear in the picture. The light gray circled things are the acrylic pieces for underglow.Show Image(http://i.imgur.com/v7El4Zw.png)
Any thoughts/feedback on the new design? Top half and bottom half are different colors to show how the halves fit together, and the light grey parts are acrylic for underglow. I wanted to keep the clean KMAC look, while also keeping the design interesting with some angles. Front has been shortened to 0.75", and the angle has been increased to 7.5 degrees.Show Image(http://i.imgur.com/4P3S1Ri.png)
Sheeeesh, looks nice!
Is it possible to use with the acrylic as well? (I'm guessing not due to the design, but still curious!)
Not really sure I understand your question 100%, but I should've made this more clear in the picture. The light gray circled things are the acrylic pieces for underglow.Show Image(http://i.imgur.com/v7El4Zw.png)
Whoops, sorry, I didn't have my coffee yet, that was a an error on my end.
I meant if it's possible to use without the acrylic. From the looks of it, it's mandatory, but I was still curious. (:
Any thoughts/feedback on the new design? Top half and bottom half are different colors to show how the halves fit together, and the light grey parts are acrylic for underglow. I wanted to keep the clean KMAC look, while also keeping the design interesting with some angles. Front has been shortened to 0.75", and the angle has been increased to 7.5 degrees.Show Image(http://i.imgur.com/4P3S1Ri.png)
Sheeeesh, looks nice!
Is it possible to use with the acrylic as well? (I'm guessing not due to the design, but still curious!)
Not really sure I understand your question 100%, but I should've made this more clear in the picture. The light gray circled things are the acrylic pieces for underglow.Show Image(http://i.imgur.com/v7El4Zw.png)
Whoops, sorry, I didn't have my coffee yet, that was a an error on my end.
I meant if it's possible to use without the acrylic. From the looks of it, it's mandatory, but I was still curious. (:
I've been toying around with the idea of metal inserts that are interchangeable with the acrylic inserts, which could look pretty cool. Less likely but still possible, there might be two revisions of the case, one withs spaces for inserts and one without.
I can't tell from your picture, but do the planes of the acrylic match up?Show Image(http://i.imgur.com/DQZMU53.png)
It looks like the top of the acrylic on the back matches up with the bottom of the front acrylic.
Personally, I don't really like this new design, the old one was much better. Is there any chance that you will still produce that one?
Personally, I don't really like this new design, the old one was much better. Is there any chance that you will still produce that one?
Note taken. Do you like the design without the acrylic inserts better?Show Image(http://i.imgur.com/lg4bXTP.png)
Personally, I don't really like this new design, the old one was much better. Is there any chance that you will still produce that one?
Note taken. Do you like the design without the acrylic inserts better?Show Image(http://i.imgur.com/lg4bXTP.png)
I like this design. The acrylic I would need to see how they work in the profile of the case before I could make a call on whether or not I like them. Is the top part of the case (dark gray) wider than the bottom part (light gray) of the case at all? You could do some nifty things with the acrylic if that was the case. If they are not, I kind of would lean towards the design in the quote.
Not really, the angles look unnecessarily messy to me and I prefer just having a straight line between the two halves. Plus I liked having the hammer-esque cutouts which look good and give you something to hold onto when picking up the keyboard.
Please keep original hammer design with kmac style, and make acrylic optional for people to choose
I dont like the new design, it looks weird what that angle between top and bottom
Any upate? I checked back but didnt see the final design tho
I think I like the second picture in the OP more. May be due to the fact it looks like there's a slight two tone color scheme going on. I think that'd look pretty cool with a darker metal top and a lighter metal base or vice versa.
Either way, I like the work you're putting into this, and I'm saving up now for when it becomes available.
I think I like the second picture in the OP more. May be due to the fact it looks like there's a slight two tone color scheme going on. I think that'd look pretty cool with a darker metal top and a lighter metal base or vice versa.
Either way, I like the work you're putting into this, and I'm saving up now for when it becomes available.
That two tone look was just to show the angles in the case design. Options for different color tops and bottoms should be available for the final product, but most people will most likely go with the same top and bottom color.
Thanks for the support though! I'll make sure to keep up with this project and get to the final buy soon(tm) enough!
I like the second one, but would prefer it without acrylic. Will that still be an option?
I would prefer the case without acrylic, if it doesn't happen then i would like to see brass as an option for metal insert? that would be really cool
+1 for keeping the hammer design, but somehow....... i feel like the cut out on the bottom is too deep which makes it almost touch the gap between top and bottom piece (maybe we can make the top piece of the case a little shorter and the bottom a little taller?) just some idea
Will the final design of the brass weight be showing out on the bottom of the case instead inside of the case?
I would prefer the case without acrylic, if it doesn't happen then i would like to see brass as an option for metal insert? that would be really cool
+1 for keeping the hammer design, but somehow....... i feel like the cut out on the bottom is too deep which makes it almost touch the gap between top and bottom piece (maybe we can make the top piece of the case a little shorter and the bottom a little taller?) just some idea
Will the final design of the brass weight be showing out on the bottom of the case instead inside of the case?
It would actually be easier to make the case without the acrylic inserts, so I don't see why it wouldn't be possible. Based on how I'm planning to go about the buy, slight variations in the cases shouldn't be hard to do.
I agree with you on the Hammer design. I'll work on trying to fix it, but I can't make the bottom taller without redoing the whole design. Worst case scenario, Hammer bottom becomes not available :(
Goal is to have the weight on the inside of the case for sturdiness, but have a little bit poke through the bottom of the case.Show Image(http://i.imgur.com/BehOzZJ.png)
Right now, I have something like this, but that design was just to test to see if it would be possible. It's easy to change that design though, and I'll be putting something more interesting and meaningful on the final design.
I would prefer the case without acrylic, if it doesn't happen then i would like to see brass as an option for metal insert? that would be really cool
+1 for keeping the hammer design, but somehow....... i feel like the cut out on the bottom is too deep which makes it almost touch the gap between top and bottom piece (maybe we can make the top piece of the case a little shorter and the bottom a little taller?) just some idea
Will the final design of the brass weight be showing out on the bottom of the case instead inside of the case?
It would actually be easier to make the case without the acrylic inserts, so I don't see why it wouldn't be possible. Based on how I'm planning to go about the buy, slight variations in the cases shouldn't be hard to do.
I agree with you on the Hammer design. I'll work on trying to fix it, but I can't make the bottom taller without redoing the whole design. Worst case scenario, Hammer bottom becomes not available :(
Goal is to have the weight on the inside of the case for sturdiness, but have a little bit poke through the bottom of the case.Show Image(http://i.imgur.com/BehOzZJ.png)
Right now, I have something like this, but that design was just to test to see if it would be possible. It's easy to change that design though, and I'll be putting something more interesting and meaningful on the final design.
Yeah, I think it should be flush, like the OTD365 Mini (no mandatory acrylic). If anything, a little add on can be provided like Revo did with the RJ, for acrylic.
Would it be possible to make the top front a bit lower? I'm not sure if it's just the picture, but the front looks a bit too tall to use without a wrist rest.
Keep up the amazing work, Snev! Can't wait to see the weight design!
I would prefer the case without acrylic, if it doesn't happen then i would like to see brass as an option for metal insert? that would be really cool
+1 for keeping the hammer design, but somehow....... i feel like the cut out on the bottom is too deep which makes it almost touch the gap between top and bottom piece (maybe we can make the top piece of the case a little shorter and the bottom a little taller?) just some idea
Will the final design of the brass weight be showing out on the bottom of the case instead inside of the case?
It would actually be easier to make the case without the acrylic inserts, so I don't see why it wouldn't be possible. Based on how I'm planning to go about the buy, slight variations in the cases shouldn't be hard to do.
I agree with you on the Hammer design. I'll work on trying to fix it, but I can't make the bottom taller without redoing the whole design. Worst case scenario, Hammer bottom becomes not available :(
Goal is to have the weight on the inside of the case for sturdiness, but have a little bit poke through the bottom of the case.Show Image(http://i.imgur.com/BehOzZJ.png)
Right now, I have something like this, but that design was just to test to see if it would be possible. It's easy to change that design though, and I'll be putting something more interesting and meaningful on the final design.
Yeah, I think it should be flush, like the OTD365 Mini (no mandatory acrylic). If anything, a little add on can be provided like Revo did with the RJ, for acrylic.
Would it be possible to make the top front a bit lower? I'm not sure if it's just the picture, but the front looks a bit too tall to use without a wrist rest.
Keep up the amazing work, Snev! Can't wait to see the weight design!
So far, that's what my plan is. Have the case be clean by default, with an add on for underglow support, as well as an addon for Hammer sides.
It's only 0.1" taller than 0.75" at 0.85". It's still a tall front, but it's a lot better than a whole 1" tall. I could probably lower the front a little bit, but I would have to drop flat bottom support, as well as support for a 5mm acrylic plate. Underglow support on the front would also have to be dropped, but it could be kept on the sides.
I would prefer the case without acrylic, if it doesn't happen then i would like to see brass as an option for metal insert? that would be really cool
+1 for keeping the hammer design, but somehow....... i feel like the cut out on the bottom is too deep which makes it almost touch the gap between top and bottom piece (maybe we can make the top piece of the case a little shorter and the bottom a little taller?) just some idea
Will the final design of the brass weight be showing out on the bottom of the case instead inside of the case?
It would actually be easier to make the case without the acrylic inserts, so I don't see why it wouldn't be possible. Based on how I'm planning to go about the buy, slight variations in the cases shouldn't be hard to do.
I agree with you on the Hammer design. I'll work on trying to fix it, but I can't make the bottom taller without redoing the whole design. Worst case scenario, Hammer bottom becomes not available :(
Goal is to have the weight on the inside of the case for sturdiness, but have a little bit poke through the bottom of the case.Show Image(http://i.imgur.com/BehOzZJ.png)
Right now, I have something like this, but that design was just to test to see if it would be possible. It's easy to change that design though, and I'll be putting something more interesting and meaningful on the final design.
Yeah, I think it should be flush, like the OTD365 Mini (no mandatory acrylic). If anything, a little add on can be provided like Revo did with the RJ, for acrylic.
Would it be possible to make the top front a bit lower? I'm not sure if it's just the picture, but the front looks a bit too tall to use without a wrist rest.
Keep up the amazing work, Snev! Can't wait to see the weight design!
So far, that's what my plan is. Have the case be clean by default, with an add on for underglow support, as well as an addon for Hammer sides.
It's only 0.1" taller than 0.75" at 0.85". It's still a tall front, but it's a lot better than a whole 1" tall. I could probably lower the front a little bit, but I would have to drop flat bottom support, as well as support for a 5mm acrylic plate. Underglow support on the front would also have to be dropped, but it could be kept on the sides.
Could an 8 degree angle be considered? It'll add more heft and solve a few problems I think. Sending you a few pictures of the angles.
any news on this case?
old design pleaaaaaaaseeeee :'(
i mean the one from the interest form sheet :(
I like the case but I am not interested in acrylic spacer or LEDs.