Author Topic: [GB] TMOv2 50% keyboard  (Read 88821 times)

0 Members and 2 Guests are viewing this topic.

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #100 on: Tue, 19 May 2020, 01:51:34 »
Just FYI for anyone else modifying or planning on using the plate files, it's scale is x16 so make sure you scale it down x16 before you actually get a plate made.

Is it? I've exported it straight from my CAD software and it shouldn't have changed physical dimensions.
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline Aevyn

  • Posts: 68
Re: [GB] TMOv2 50% keyboard
« Reply #101 on: Tue, 19 May 2020, 02:23:33 »
Just FYI for anyone else modifying or planning on using the plate files, it's scale is x16 so make sure you scale it down x16 before you actually get a plate made.

Is it? I've exported it straight from my CAD software and it shouldn't have changed physical dimensions.
It was when I opened it up in fusion. Instead of the switch cutouts being 19.05 mm they were 304.8 mm.

Sent from my GM1915 using Tapatalk


Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #102 on: Tue, 19 May 2020, 02:59:27 »
Just FYI for anyone else modifying or planning on using the plate files, it's scale is x16 so make sure you scale it down x16 before you actually get a plate made.

Is it? I've exported it straight from my CAD software and it shouldn't have changed physical dimensions.
It was when I opened it up in fusion. Instead of the switch cutouts being 19.05 mm they were 304.8 mm.

Sent from my GM1915 using Tapatalk

Damn, that seems a tad incorrect. :D I'll check up on what I can do. Or at least add a disclaimer.
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline Aevyn

  • Posts: 68
Re: [GB] TMOv2 50% keyboard
« Reply #103 on: Tue, 19 May 2020, 03:11:37 »
Just FYI for anyone else modifying or planning on using the plate files, it's scale is x16 so make sure you scale it down x16 before you actually get a plate made.

Is it? I've exported it straight from my CAD software and it shouldn't have changed physical dimensions.
It was when I opened it up in fusion. Instead of the switch cutouts being 19.05 mm they were 304.8 mm.

Sent from my GM1915 using Tapatalk

Damn, that seems a tad incorrect. :D I'll check up on what I can do. Or at least add a disclaimer.
No worries. I also scaled it down and can just add a link to those here when I get a chance tomorrow.

Sent from my GM1915 using Tapatalk


Offline schmidtonyoface

  • Posts: 1
Re: [GB] TMOv2 50% keyboard
« Reply #104 on: Tue, 19 May 2020, 19:15:08 »
Have sent a quick message to you regarding my order funderburker, I haven't ever used geekhack and nothing shows up in my sent items so idk if I'm just being an imbecile here or what.
E-white looks gorgeous by the way.

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #105 on: Wed, 20 May 2020, 02:26:00 »
Have sent a quick message to you regarding my order funderburker, I haven't ever used geekhack and nothing shows up in my sent items so idk if I'm just being an imbecile here or what.
E-white looks gorgeous by the way.

Hi. I replied to you, please check your PMs under "Messages".
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline LXYN

  • Posts: 5
Re: [GB] TMOv2 50% keyboard
« Reply #106 on: Thu, 21 May 2020, 13:15:12 »
Looks great. I want buy extra.... T.T pls...

Offline ReverbSlush

  • Posts: 254
  • 16/52 RNG score
Re: [GB] TMOv2 50% keyboard
« Reply #107 on: Thu, 21 May 2020, 15:04:36 »
got mine in today... daaaaang e-white looking real nice.

For some reason I bought (in addition to the e-white kit) an extra poly bottom, PCB and plate, but not an extra top... I can't remember what I was thinking.. maybe a lighter travel board or alternate layout? was there a poly top option?  My mental failings aside, this is slick! thanks for putting together a 2nd round.


Offline of_sam

  • Posts: 272
  • Location: United States
Re: [GB] TMOv2 50% keyboard
« Reply #108 on: Thu, 21 May 2020, 15:19:22 »
got mine in today... daaaaang e-white looking real nice.

For some reason I bought (in addition to the e-white kit) an extra poly bottom, PCB and plate, but not an extra top... I can't remember what I was thinking.. maybe a lighter travel board or alternate layout? was there a poly top option?  My mental failings aside, this is slick! thanks for putting together a 2nd round.

Look under add-ons on the first page of this thread. Extra bottom was just an add-on option for people that wanted underglow.
Typing on: HHKB Pro 2 - Stock :aware:
Collection: F1.69, Police, Jubi, RF 87U, En Dash, Rosenthal, Soulless, Frog, Calliope, GAF 910, Sabre, W1-AT

Offline ReverbSlush

  • Posts: 254
  • 16/52 RNG score
Re: [GB] TMOv2 50% keyboard
« Reply #109 on: Thu, 21 May 2020, 20:35:46 »
Look under add-ons on the first page of this thread. Extra bottom was just an add-on option for people that wanted underglow.

I know *how* it happened... just not sure *why*.  I probably figured I could switch the top back and forth...

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #110 on: Fri, 22 May 2020, 03:10:00 »
Look under add-ons on the first page of this thread. Extra bottom was just an add-on option for people that wanted underglow.

I know *how* it happened... just not sure *why*.  I probably figured I could switch the top back and forth...

Well, you can switch'em back and forth. :D You can always flip lol
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline sleepy

  • Posts: 174
Re: [GB] TMOv2 50% keyboard
« Reply #111 on: Fri, 22 May 2020, 12:19:33 »


this thing is amazing - the quality is blowing me away. great job funderburker and upas! i'm nervous to build it it looks so nice!!

Offline x9Memoriez

  • Posts: 83
  • Location: Sydney, Australia
Re: [GB] TMOv2 50% keyboard
« Reply #112 on: Fri, 22 May 2020, 21:05:21 »
Custom australian green anno! Cheers funder :)

243262-0
Matrix 1.2OG | Constellation | Rukia | TMO50 | HHKB

Offline AuthenticDanger

  • Posts: 402
Re: [GB] TMOv2 50% keyboard
« Reply #113 on: Fri, 22 May 2020, 21:24:58 »
Just FYI for anyone else modifying or planning on using the plate files, it's scale is x16 so make sure you scale it down x16 before you actually get a plate made.

Big Switch TMO incoming!!!!
F Keys belong on the left.

Offline nathanchere

  • Posts: 707
Re: [GB] TMOv2 50% keyboard
« Reply #114 on: Tue, 02 June 2020, 09:21:35 »
Just received notification that my TMOv2 has arrived from CannonKeys to Australia :D Now it's just an anxious wait for the state of international travel to settle to a point that I can actually go pick it up...

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #115 on: Tue, 02 June 2020, 13:49:37 »
Custom australian green anno! Cheers funder :)

(Attachment Link)

This is just too good of a colour combo! Feeling a bit salty for not getting a green one.  :)
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline j0hn3h

  • Posts: 15
Re: [GB] TMOv2 50% keyboard
« Reply #116 on: Tue, 02 June 2020, 21:19:06 »
I'm having difficulties flashing mines. QMK Toolbar detects it, but when clicking Flash, it would say no devices detected

*** Listing compatible HID devices: (must have Usage Page 0xFF31)
     - CannonKeys: TMOv2 -- CA04:70F2:0001 (8&35a7566b&0&0000)
  ! There are no devices available

Is this due to my computer not having the proper drivers?

Thanks.

Offline clik_clak

  • Posts: 423
Re: [GB] TMOv2 50% keyboard
« Reply #117 on: Tue, 02 June 2020, 21:26:36 »
I'm having difficulties flashing mines. QMK Toolbar detects it, but when clicking Flash, it would say no devices detected

*** Listing compatible HID devices: (must have Usage Page 0xFF31)
     - CannonKeys: TMOv2 -- CA04:70F2:0001 (8&35a7566b&0&0000)
  ! There are no devices available

Is this due to my computer not having the proper drivers?

Thanks.

Sounds more like you aren't going into the bootloader before you're attempting to flash.

Offline scoopbb

  • Posts: 271
Re: [GB] TMOv2 50% keyboard
« Reply #118 on: Tue, 02 June 2020, 23:01:13 »
I'm having difficulties flashing mines. QMK Toolbar detects it, but when clicking Flash, it would say no devices detected

*** Listing compatible HID devices: (must have Usage Page 0xFF31)
     - CannonKeys: TMOv2 -- CA04:70F2:0001 (8&35a7566b&0&0000)
  ! There are no devices available

Is this due to my computer not having the proper drivers?

Thanks.

there is a dip switch on the bottom of the pcb that needs to be set to 1, then you can flaash. Set it back to 0 after

Offline lanyusea

  • Posts: 334
Re: [GB] TMOv2 50% keyboard
« Reply #119 on: Wed, 03 June 2020, 07:45:01 »
just got mine today :D244239-0244241-1
HHKB Type-s / 4x KMAC Happy / 3x Duck Viper v1 / 2x Duck Viper v2 / 4x Duck Viper Duck TCV3 / Red Scarf 77 / 2x Infinity 60 / 2x ALF HHKB / LZ-CE / FJELL / Canoe / Canoe PC / Canoe FE / ARES Prototype / 2x Ares / LC-CLSh / TX60 / YODA2 / E6-V2 / E6-V2 FE / CAMP LC60 / 2x EM 7 / 4x Leaf 60 / UHK / Project F / Polaris / 4x Duck Viper v3 / TX60 v2 / Thermal / Matrix Falcon / TX60 v3 / 2x TMO50 / 2x Dolice / Dolphin 65 / Dolphin 60 / Plenty of keycaps

Offline j0hn3h

  • Posts: 15
Re: [GB] TMOv2 50% keyboard
« Reply #120 on: Wed, 03 June 2020, 16:20:15 »
I'm having difficulties flashing mines. QMK Toolbar detects it, but when clicking Flash, it would say no devices detected

*** Listing compatible HID devices: (must have Usage Page 0xFF31)
     - CannonKeys: TMOv2 -- CA04:70F2:0001 (8&35a7566b&0&0000)
  ! There are no devices available

Is this due to my computer not having the proper drivers?

Thanks.

there is a dip switch on the bottom of the pcb that needs to be set to 1, then you can flaash. Set it back to 0 after

Thanks for letting me know! Set to 1 and got into DFU mode.

When flashing, it doesn't detect the DFU.

I've got all the drivers installed, qmk toolbox updated them upon opening.

Is the MCU atmega3232u4?

Thank you!

Offline Skynic

  • Posts: 2
Re: [GB] TMOv2 50% keyboard
« Reply #121 on: Sun, 07 June 2020, 07:31:33 »
I apologise for my ignorance - is this group buy now done? Or will it be available to order in November.

Offline damagepoint

  • Posts: 44
Re: [GB] TMOv2 50% keyboard
« Reply #122 on: Sun, 07 June 2020, 07:35:15 »
I apologise for my ignorance - is this group buy now done? Or will it be available to order in November.

Hey man, unfortunately the group buy happened last November.  The units are currently shipping out, there may be extras that would go up after all the gb units ship. 

Offline upas

  • Posts: 355
Re: [GB] TMOv2 50% keyboard
« Reply #123 on: Sun, 07 June 2020, 10:23:16 »
I'm having difficulties flashing mines. QMK Toolbar detects it, but when clicking Flash, it would say no devices detected

*** Listing compatible HID devices: (must have Usage Page 0xFF31)
     - CannonKeys: TMOv2 -- CA04:70F2:0001 (8&35a7566b&0&0000)
  ! There are no devices available

Is this due to my computer not having the proper drivers?

Thanks.

there is a dip switch on the bottom of the pcb that needs to be set to 1, then you can flaash. Set it back to 0 after

Thanks for letting me know! Set to 1 and got into DFU mode.

When flashing, it doesn't detect the DFU.

I've got all the drivers installed, qmk toolbox updated them upon opening.

Is the MCU atmega3232u4?

Thank you!

The MCU is STM32, you'll likely have to use zadig on windows to get the proper drivers installed for it.

Docs are available here: https://docs.cannonkeys.com/an_c/#flashing

Offline Skynic

  • Posts: 2
Re: [GB] TMOv2 50% keyboard
« Reply #124 on: Sun, 07 June 2020, 13:58:30 »
I apologise for my ignorance - is this group buy now done? Or will it be available to order in November.

Hey man, unfortunately the group buy happened last November.  The units are currently shipping out, there may be extras that would go up after all the gb units ship.

Ah, too bad! I would love to hear if there are any additional units that become available - how will I be able to hear about them?

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #125 on: Mon, 08 June 2020, 02:57:23 »
I apologise for my ignorance - is this group buy now done? Or will it be available to order in November.

Hey man, unfortunately the group buy happened last November.  The units are currently shipping out, there may be extras that would go up after all the gb units ship.

Ah, too bad! I would love to hear if there are any additional units that become available - how will I be able to hear about them?

Hey! I suggest you join mykeyboard.eu and/or Cannon Keys discord servers and join their newsletters as well. Depends where you're located as mykeyboard.eu is EU vendor and Cannon Keys being US vendor.
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline zokey.1119

  • Posts: 3
Re: [GB] TMOv2 50% keyboard
« Reply #126 on: Tue, 09 June 2020, 02:45:06 »
Did anyone use Mill-max socket on pcb? Which type did you use? I only have the access of the type of 0305-2-15-80-47-80-10-0.
The link is here : https://www.digikey.hk/product-detail/en/mill-max-manufacturing-corp/0305-2-15-80-47-80-10-0/ED90584-ND/2639493



Does anyone know if this type fit to this pcb?

Thanks :)

Offline ishwerp

  • Posts: 5
Re: [GB] TMOv2 50% keyboard
« Reply #127 on: Wed, 24 June 2020, 22:23:57 »
Are there any plans for there to be a round 2 for this or maybe even a v3?  ;D

Offline scoopbb

  • Posts: 271
Re: [GB] TMOv2 50% keyboard
« Reply #128 on: Wed, 24 June 2020, 22:52:06 »
Did anyone use Mill-max socket on pcb? Which type did you use? I only have the access of the type of 0305-2-15-80-47-80-10-0.
The link is here : https://www.digikey.hk/product-detail/en/mill-max-manufacturing-corp/0305-2-15-80-47-80-10-0/ED90584-ND/2639493



Does anyone know if this type fit to this pcb?

Thanks :)

i have 7305 in mine

Offline zokey.1119

  • Posts: 3
Re: [GB] TMOv2 50% keyboard
« Reply #129 on: Wed, 24 June 2020, 23:41:26 »
Did anyone use Mill-max socket on pcb? Which type did you use? I only have the access of the type of 0305-2-15-80-47-80-10-0.
The link is here : https://www.digikey.hk/product-detail/en/mill-max-manufacturing-corp/0305-2-15-80-47-80-10-0/ED90584-ND/2639493



Does anyone know if this type fit to this pcb?

Thanks :)

i have 7305 in mine

Thanks!!

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #130 on: Fri, 03 July 2020, 05:09:32 »
One last update (probably) [2020-07-03]

First of all, I'd like to thank each and every one of you for the support during the GB phase and also for being a wonderful group of people that enjoys your boards. A lot of you that have received your boards, be it from Cannon Keys, MyKeyboard.eu or AEBoards, have shared great photos and builds and each one of the boards has been just awesome! I truly feel proud of how this GB has happened and how happy and excited a lot of you have been to receive your own "tiny mechanical object".

Secondly, for the people that for some reason haven't had the chance to get your hands on one, there's a chance for you TOMORROW (Saturday, July 4th at 11 AM ETS) on Cannon Keys as there's gonna be some extras and B-stock, as well as extra add-ons for those of you that have a TMOv2 but wants to get a PCB, plate or PC bottom. ;) If you want to be up-to-date and just chat about the board and have any other questions about extras, please visit Cannon Keys Discord server.

Again - thank you for the wonderful reception and this has truly been a big thing for me and is very motivating to keep doing what I can only call my biggest accomplishment thus far. This hobby and the community means a lot to me and it's been a great journey for me and hopefully for y'all too!

Peace and stay safe,
funderburker
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline nathanchere

  • Posts: 707
Re: [GB] TMOv2 50% keyboard
« Reply #131 on: Sat, 04 July 2020, 10:13:24 »
Sold out already :(

Offline TacoSausje

  • Posts: 6
Re: [GB] TMOv2 50% keyboard
« Reply #132 on: Sat, 04 July 2020, 12:20:55 »
Oof I tried to get this at work but no luck :(.
Now praying for the Ogre

Offline j0hn3h

  • Posts: 15
Re: [GB] TMOv2 50% keyboard
« Reply #133 on: Sat, 04 July 2020, 21:07:29 »
I'm having difficulties flashing mines. QMK Toolbar detects it, but when clicking Flash, it would say no devices detected

*** Listing compatible HID devices: (must have Usage Page 0xFF31)
     - CannonKeys: TMOv2 -- CA04:70F2:0001 (8&35a7566b&0&0000)
  ! There are no devices available

Is this due to my computer not having the proper drivers?

Thanks.

there is a dip switch on the bottom of the pcb that needs to be set to 1, then you can flaash. Set it back to 0 after

Thanks for letting me know! Set to 1 and got into DFU mode.

When flashing, it doesn't detect the DFU.

I've got all the drivers installed, qmk toolbox updated them upon opening.

Is the MCU atmega3232u4?

Thank you!

The MCU is STM32, you'll likely have to use zadig on windows to get the proper drivers installed for it.

Docs are available here: https://docs.cannonkeys.com/an_c/#flashing

Thanks for all the help! I was able to flash it.

For anyone interested, I set the dip switch to 1 and had zadig opened up, then plugged in the pcb. It was able to recognize and install the drivers.

After that, you can flash it normally as any other qmk compatible pcb. I set mines up with VIA after watching Nathan's (Taeha Types) stream.

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #134 on: Sun, 05 July 2020, 05:32:42 »
Thanks for all the help! I was able to flash it.

For anyone interested, I set the dip switch to 1 and had zadig opened up, then plugged in the pcb. It was able to recognize and install the drivers.

After that, you can flash it normally as any other qmk compatible pcb. I set mines up with VIA after watching Nathan's (Taeha Types) stream.

That's wonderful to hear! Enjoy the board man!  :thumb:
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline Leviathan

  • Posts: 67
  • Location: NH-US
Re: [GB] TMOv2 50% keyboard
« Reply #135 on: Thu, 10 December 2020, 09:02:04 »
Any chance of another round?

Offline MattyRice

  • Posts: 7
Re: [GB] TMOv2 50% keyboard
« Reply #136 on: Thu, 10 December 2020, 12:17:43 »
^ I second another round please

Offline funderburker

  • * Exquisite Elder
  • Thread Starter
  • Posts: 1395
  • Location: Latvia, Riga
Re: [GB] TMOv2 50% keyboard
« Reply #137 on: Mon, 14 December 2020, 05:17:44 »
Any chance of another round?

^ I second another round please

Yes, there will be another round of TMOv2s. Still figuring timeline but definitely in the first half of 2021. No further details rn.
Keyboard design by Skepur

My boards: TMO50 FE:06 | LAGOM Groda-T | TMOv2 R1 prototype | Onyx FRL TKL prototype | Stege TKL prototype | Ellipse prototype | Cyberstar

Offline crestia

  • Posts: 33
Re: [GB] TMOv2 50% keyboard
« Reply #138 on: Mon, 14 December 2020, 09:58:12 »
now this is the hype news that i have been waiting for!

Offline MattyRice

  • Posts: 7
Re: [GB] TMOv2 50% keyboard
« Reply #139 on: Thu, 17 December 2020, 10:41:08 »
SWEEEEET, was planning to jump in on a 65% keeb this month but for sure i'm holding out now for this!

Offline dexie

  • Posts: 92
  • Location: Riga, Latvia
Re: [GB] TMOv2 50% keyboard
« Reply #140 on: Thu, 17 December 2020, 12:02:36 »
Yes! No way I will miss it this time.
ISO Life

Offline synthtastic

  • Posts: 172
Re: [GB] TMOv2 50% keyboard
« Reply #141 on: Thu, 17 December 2020, 15:22:11 »
Very sexy news indeed...
Expensive plastic makes me sigh.

Offline roostrc0gburn

  • * Esteemed Elder
  • Posts: 1444
  • Location: Oregon
  • its just plastic
Re: [GB] TMOv2 50% keyboard
« Reply #142 on: Thu, 17 December 2020, 16:22:24 »
full brass pls

Offline ogp3

  • Posts: 111
Re: [GB] TMOv2 50% keyboard
« Reply #143 on: Thu, 17 December 2020, 21:23:17 »
I hope the pink pc is offered again! Would love that!

Offline yuejia

  • Posts: 71
Re: [GB] TMOv2 50% keyboard
« Reply #144 on: Sat, 19 December 2020, 07:33:21 »
Awesome!!! :) :) :)

Offline yuejia

  • Posts: 71
Re: [GB] TMOv2 50% keyboard
« Reply #145 on: Mon, 21 December 2020, 00:45:14 »
That‘s so cool! I like it!!!

Offline TheBlackHammer

  • Posts: 117
Re: [GB] TMOv2 50% keyboard
« Reply #146 on: Sat, 13 February 2021, 15:01:05 »
any updates on the next round for the TMO?