[GB] LZ CLS (Classic TKL) : Finished

[HappyCatFish]

What switches do you guys use polycarb with?

I am a huge fan of the ergo-clears on the plastic plate that I built my Orion V2 with, but at the end of the day it's all personal preference. Build it how you want it.

[gadzkun]

hi LZ i finished build my alps CLS, but something wrong with it.



at first i was think it maybe my switch was broken, so i try to change it with another one, but it still wont work,
so i try to change diode too but it still wont work too.

can you help me with it? i got so many problem with my LZ-CLS to be honest

[loud_asian]

hi LZ i finished build my alps CLS, but something wrong with it.

Show Image

at first i was think it maybe my switch was broken, so i try to change it with another one, but it still wont work,
so i try to change diode too but it still wont work too.

can you help me with it? i got so many problem with my LZ-CLS to be honest :(

Show Image

Did you test the PCB before you soldered?

[alienman82]

removed.

[OfTheWild]

I'm guessing some of those barrel resistors arent right... they were pretty tricky to solder.

[Puddsy]

I'm guessing some of those barrel resistors arent right... they were pretty tricky to solder.

Show Image

looks weird with no centerholes

[alienman82]

removed.

[Puddsy]

I'm guessing some of those barrel resistors arent right... they were pretty tricky to solder.

Show Image

diodes?

shoulda got the ones packaged in plastic.  those glass ones look scary like they will break

it's what's included with the PCBs

i got the same ones from kin when i got my 3000 pcb

[gadzkun]

DSA on alps is something I'd like to try.

you like that?

Hmmm i still dont know yet how it feels its my first time build alps xD

But its quite good i still try adapt to it.

I'm guessing some of those barrel resistors arent right... they were pretty tricky to solder.

Show Image

I ask my friend who really good at soldering so i will ask him again to check it.

hi LZ i finished build my alps CLS, but something wrong with it.

Show Image

at first i was think it maybe my switch was broken, so i try to change it with another one, but it still wont work,
so i try to change diode too but it still wont work too.

can you help me with it? i got so many problem with my LZ-CLS to be honest

Show Image

Did you test the PCB before you soldered?

I dont know how to check pcb xD. I'll ask my friend to check it.

[zimo]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

[DreLLin]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

[mech0nly]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

[zimo]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

Thanks！！

[zimo]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

How to into the USB mode，I cant conect keyboard

[DreLLin]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

How to into the USB mode，I cant conect keyboard

Ok, here is another step by step manual:

- Download L3_170419.zip (http://kbdlab.co.kr/?module=file&act=procFileDownload&file_srl=4320094&sid=ebbdca3c12b3174f582b4c8dc470ecce)
- Download JigOn_170419.zip (http://kbdlab.co.kr/?module=file&act=procFileDownload&file_srl=4320093&sid=a2dfd681007fec4c849850a5530a4df9)
- Unzip both files go
- Open loadfw.bat in L3_170419
- It will then flash the Leeku L3 keyboard with that version of the firmware.
- If you get a “communications error” when flashing, try a different USB cable and/or port. For me, it turned out using a different port worked, even though the keyboard could *type stuff* using the first port, it couldn’t flash the board.
- Open JigOn.exe in JigOn_170419 Folder
- Download and follow the guide Leeku L3 Software.pdf from https://www.dropbox.com/sh/v24vygvyl4mvqrm/AABUNcm0BDioYE5QbArje0Kba?dl=1

Hope this helps.

[zimo]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

How to into the USB mode，I cant conect keyboard

Ok, here is another step by step manual:

- Download L3_170419.zip (http://kbdlab.co.kr/?module=file&act=procFileDownload&file_srl=4320094&sid=ebbdca3c12b3174f582b4c8dc470ecce)
- Download JigOn_170419.zip (http://kbdlab.co.kr/?module=file&act=procFileDownload&file_srl=4320093&sid=a2dfd681007fec4c849850a5530a4df9)
- Unzip both files go
- Open loadfw.bat in L3_170419
- It will then flash the Leeku L3 keyboard with that version of the firmware.
- If you get a “communications error” when flashing, try a different USB cable and/or port. For me, it turned out using a different port worked, even though the keyboard could *type stuff* using the first port, it couldn’t flash the board.
- Open JigOn.exe in JigOn_170419 Folder
- Download and follow the guide Leeku L3 Software.pdf from https://www.dropbox.com/sh/v24vygvyl4mvqrm/AABUNcm0BDioYE5QbArje0Kba?dl=1

Hope this helps.

Very detailed, thank you for your patience!

[megaforce]

Promised someone photos of my cerakote'd TX-84 here (better late than never): https://imgur.com/a/tLILX

[Unforgivable]

Promised someone photos of my cerakote'd TX-84 here (better late than never): https://imgur.com/a/tLILX

Very nice! Was this place local? How much did it run you? Any pros/cons versus standard anode?

[CommonCurt]

Promised someone photos of my cerakote'd TX-84 here (better late than never): https://imgur.com/a/tLILX

Nice! Thanks for posting.

[megaforce]

Promised someone photos of my cerakote'd TX-84 here (better late than never): https://imgur.com/a/tLILX

Very nice! Was this place local? How much did it run you? Any pros/cons versus standard anode?

Thanks! Yes it was local, ran $110 in cash (was less if I wanted one color). With cerakote you necessarily don't have to strip the original anodizating and an even result is easier to achieve than anodizing.

Promised someone photos of my cerakote'd TX-84 here (better late than never): https://imgur.com/a/tLILX

Nice! Thanks for posting.

You're welcome!

[popkorn62]

Selling Alu plate + PCB

I’m keeping the diffuser. Please pm.


======••••======
http://txkeyboards.com/

Please click LOG IN on register. Bottom page is for newsletter only.

[techfresh]

Selling Alu plate + PCB

Show Image

I’m keeping the diffuser. Please pm.


======••••======
http://txkeyboards.com/

Please click LOG IN on register. Bottom page is for newsletter only.

Pm’ed


Sent from my iPhone using Tapatalk

[DreLLin]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

Got my CLS and the custom brass and pc plates today. The brass plate needed some polishing but turned out nice. Paid 194€ including 19% VAT for both plates but wanted them to be produced locally.





If interested, you can watch the complete build log at Imgur. https://imgur.com/a/zDHXR

[airs]

Got my CLS and the custom brass and pc plates today. The brass plate needed some polishing but turned out nice. Paid 194€ including 19% VAT for both plates but wanted them to be produced locally.

(Attachment Link)
(Attachment Link)
(Attachment Link)

If interested, you can watch the complete build log at Imgur. https://imgur.com/a/zDHXR

Great build log DreLLin - thanks for posting! What is the reason for this step - "Clipping the legs of the switches for the Alphas. Keeping the legs on Mods and ISO keys with larger plate cutouts"

Also wondering why you used GPL105, GPL106 and the VW lube (GPL105)? Why the spray lube in addition to the drops?

[DreLLin]

The legs of the Zeal switches are a little bigger than the cherry ones. It's really hard to push them into the pcb and almost impossible to have them seated flush with the plate and pcb without clipping the legs.
Since the alphas have great support from the plate and alignment is no concern you can clip the legs of the switches without sacrificing anything.

On the mods and ISO keys you have larger plate cutouts and it's harder to align the switches correctly. That's why I dont't clip the legs on these keys and am not so concerned if they aren't 1000% flush with the pcb.

I used the bag before I had the spray for other switches so there was some GPL 105 left in it. From now on I'll only use 106 and the spray since it makes it a bit easier to spread out the lube in the bag and a bit less shaking is required.

[airs]

The legs of the Zeal switches are a little bigger than the cherry ones. It's really hard to push them indto the pcb and almost impossible to have them seated flush with the plate and pcb without clipping the legs.
Since the alphas have great support from the plate and alignment is no concern you can clip the legs of the switches without sacrificing anything.

On the mods and ISO keys you have larger plate cutouts and it's harder to align the switches correctly. That's why I dont't clip the legs on these keys and am not so concerned if they aren't 1000% flush with the pcb.

I used the bag before I had the spray for other switches so there was some GPL 105 left in it. From now on I'll only use 106 and the spray since it makes it a bit easier to spread out the lube in the bag and a bit less shaking is required.

Makes sense, thanks for the reply!

[jenggo]

Just Finished fixing Gadzkun's CLS.
about 3 controller feet doesn't soldered well to the pcb.
many diodes not soldered to the pcb
and polished the weight
https://i.imgur.com/b5O6iaD.jpg

  

[avid]

Very nice! The black finish is so good. Do you have more pics but of front?

[Dreamre]

Just Finished fixing Gadzkun's CLS.
about 3 controller feet doesn't soldered well to the pcb.
many diodes not soldered to the pcb
and polished the weight
https://i.imgur.com/b5O6iaD.jpg

  

What did you use to polish?

[futurecrime]

Is there any tutorial about firmware？

I don't know how to set it, I don't even know how to get into it

The PCB is Designed/Developed by Leeku
The PCB is Programmed with JigOn firmware : http://kbdlab.co.kr/index.php?mid=board_sw&document_srl=2702787

-------------------------------------------------

PCB S/W (JigOn)
 English language documentation for Leeku's L3 Boards
https://geekhack.org/index.php?topic=83950.msg2236885#msg2236885

Are the plate files for the CLS available? Would love to get a brass and/or pc or carbon plate.

LZ CLS Self Tunning   

For CLS MX switch plate(1.5mm)
https://goo.gl/a2w2o3

For CLS Weight plate(5mm)
https://goo.gl/DB6JTd

I might be interested in pc plate, its too expensive to cut for myself alone.

Got my CLS and the custom brass and pc plates today. The brass plate needed some polishing but turned out nice. Paid 194€ including 19% VAT for both plates but wanted them to be produced locally.

[ Attachment Invalid Or Does Not Exist ]
[ Attachment Invalid Or Does Not Exist ]
[ Attachment Invalid Or Does Not Exist ]

If interested, you can watch the complete build log at Imgur. https://imgur.com/a/zDHXR

Really nice build log and great result. Thanks for taking the time to do it, I took a few tips to use on my next build.

[mech0nly]

Hmmmmmmm, I tried to desolder the USB connector and one of the metal pad that, to me, should stays on the PCB came right off is that normal  .
I'm freaking out right now, not sure if I just broke the PCB or not.

Can USB connector wired to this pad?

Currently i have GON Nerd PCB, but the connector was beneath of the PCB (instead of on top), it must be on top in order to compatible with CLS. Actually there's a pad on top, but the extras part of PCB was cut from vendor (along with the top pad). I just knew this when it arrived. Help.... 


Really sorry for potato pic

[mech0nly]

.

[alienman82]

removed.

[rabbitfire]

My connector failed out so I had to desolder everything and solder the connect to PCB. But, it doesn't work. Anyone know how to fix this issue?

[Delirious]

A bit late because I have to wait for the Time's pcb. My latest abomination with SKCM Blues, hebrew keyset, and a circumcised penis for escape key.

[GeneriksGiraffe]

Will there every be a rerun of this? I am so sad I missed this! A custom ALPS tkl would be glorious.

[Puddsy]

Will there every be a rerun of this? I am so sad I missed this! A custom ALPS tkl would be glorious.

probably not