Show Image(http://i.imgur.com/MMZSRnU.png)
Most people use the forum standard, which has a dark grey background. It's best not to use black lettering. ;)
That's clearly a message to use the superior white theme! :pShow Image(http://i.imgur.com/MMZSRnU.png)
Most people use the forum standard, which has a dark grey background. It's best not to use black lettering. ;)
It would be great to get links to the layouts through "keyboard layout editor"
the picture lacks the screw holes, do they have holes for all 6 60% case screws?
Pardon my ignorance, but what stabilizers are supported? Plate? PCB? or Plate/PCB?
Everything that is officially supported by the SwillKB's tool.
Everything should be supported, but at least plate Cherry and plate Costar. I test when i get the samples.
:)
What are the economics behind this gb? From what I see is these are exactly the same prices can be obtained for example on lasermaster.co.uk...
Plus, sorry again... but you are trying to sell an untested object?????
Looking good :D I'll be definitely buying some.
Will definitly buy one for a custom 60%, mostly because of the low shipping to EU :D
I'm in for an ansi, 60%.. Way overdue for a properly programmable customer.Nice! Overdue for what?
In for ISONice! Another fellow ISOer :)
Something arduino ish that lets me run colemak and spacefn. I was hoping the poker 3 was going to be fully programmable but no such luck.Sounds cool! I personally still use hand wiring because there are almost no reasonable priced, easy to get PCBs for me.
I know there are some Chinese gh60 early revision pcb's floating around but I'm not sure what the quality is like. I may end up hand wiring if nothing shows up.
Something arduino ish that lets me run colemak and spacefn. I was hoping the poker 3 was going to be fully programmable but no such luck.
I know there are some Chinese gh60 early revision pcb's floating around but I'm not sure what the quality is like. I may end up hand wiring if nothing shows up.
The naming of that plate is a little ehh... controversial...Something arduino ish that lets me run colemak and spacefn. I was hoping the poker 3 was going to be fully programmable but no such luck.
I know there are some Chinese gh60 early revision pcb's floating around but I'm not sure what the quality is like. I may end up hand wiring if nothing shows up.
I bought a GH60 Satan edition from taobao, and while I haven't built it up yet, it seems pretty good. Some people were complaining that they can't get it programmed correctly, though.
I saw it to. Do you think the programming is easy to use, or more complicated?
Hmm. Would be interesting with a GB for it with super cheap prices.I saw it to. Do you think the programming is easy to use, or more complicated?
Seems complicated: https://geekhack.org/index.php?topic=66624.msg1712129#msg1712129
Something arduino ish that lets me run colemak and spacefn. I was hoping the poker 3 was going to be fully programmable but no such luck.Pok3r should have Colemak via DIP switches.
I know there are some Chinese gh60 early revision pcb's floating around but I'm not sure what the quality is like. I may end up hand wiring if nothing shows up.
Hmm. Would be interesting with a GB for it with super cheap prices.I saw it to. Do you think the programming is easy to use, or more complicated?
Seems complicated: https://geekhack.org/index.php?topic=66624.msg1712129#msg1712129
For sure.Hmm. Would be interesting with a GB for it with super cheap prices.I saw it to. Do you think the programming is easy to use, or more complicated?
Seems complicated: https://geekhack.org/index.php?topic=66624.msg1712129#msg1712129
Yes, I asked in that thread "I just ordered one from taobao seller loveq. Maybe someone could get in contact with him? He sells Gaterons, GH60 Satan, and stabilizers through taobao, but I'd rather deal with him directly without a taobao agent, if at all possible."
If someone could do a mini GB from him for PCBs, switches, stabilizers...I think it would be pretty popular.
I live in Finland, so it should be convenient enough getting them from you ;)Looking good :D I'll be definitely buying some.
Yay! EU or CONUS?
Yes it will! Super awesome to see some Europeans here to. (Still love you Americans and other Internationals)I live in Finland, so it should be convenient enough getting them from you ;)Looking good :D I'll be definitely buying some.
Yay! EU or CONUS?
Hi! If I wanted to change an ISO Pok3r to ansi layout (because cap sets), would this work? A reviewer was pretty sure the pcb could host both layouts without modification. I live in Finland too.
I'm getting one of each.Nice!
If you are feeling overly motivated a 40% plate would be pretty interesting.40% keyboards are quite interesting, yes. If I run a new GB I might add some options and do a MOQ.
There seems to be a shortage of 40% case shells but a jd40 type layout frame that matched screw holes with the planck case might be a winner.
I've been waiting for another shot at the jd40 for a while but it hasn't been available for a while.
I'm pretty sure a jd40 layout with spacefn could replace my poker as my keyboard for my bag back and forth from work.
I keep hoping to see the textblade come out as a success but the delays in getting to production and the associated delays in software development seem to leave them a long way from delivering the board with usable pc/linux layouts.
40% keybs are very interesting but I believe everyone would seek a custom layout.
When does this GB close? I'm afraid I won't be getting paid for a few weeks and that plate is so sexy, and at a wonderful price too :'(It isn't started yet. I may get the plates next week, validate a few days an then open orders if everything is okay. I will have orders open as long as I am getting a significant amount of orders.
Will these plates fit in a poker II case?That is the plan, yes :)
Just a little note: It looks like there's a little bug with the combined stab cutout in swill's tool:I saw it. Is that fixed now by Swill ?
https://geekhack.org/index.php?topic=65189.msg1741788#msg1741788
You probably have to update the plate files.
I hope soon.Just a little note: It looks like there's a little bug with the combined stab cutout in swill's tool:I saw it. Is that fixed now by Swill ?
https://geekhack.org/index.php?topic=65189.msg1741788#msg1741788
You probably have to update the plate files.
Thanks for updating anyways! I will look into it and make sure the plates you get works :) I dont think I will order more samples, if the one I get tomorrow work, except for the stabs, I will start the GB wit corrected design from Swill.I hope soon.Just a little note: It looks like there's a little bug with the combined stab cutout in swill's tool:I saw it. Is that fixed now by Swill ?
https://geekhack.org/index.php?topic=65189.msg1741788#msg1741788
You probably have to update the plate files.
https://geekhack.org/index.php?topic=65189.msg1744036#msg1744036
Show Image(http://i.imgur.com/MMZSRnU.png)
Most people use the forum standard, which has a dark grey background. It's best not to use black lettering. ;)
Can you post some close ups of the plate?
Sandblasted definitely looks better IMO.Thanks for your opinion. :)
Which ever coating make it easier to powder coat the plate im for that. Also will the corners be rounded? would be nice to have a flush fit on a pok3r case.I will see how it fits in the Pok3r case and decide if I want to round the corners.
Sand blasted! Looks great ;)Looks like I am going for sandblasted :)
super excited for this! i'm never built my own board, but now i'll have to.:)
I like brushed better but anything would do.Thanks for your feedback :)
Voted! Nice job LeandreN! :thumb:
Any news on the rounded corners?Haven't tested the it in the case yet, but I will decide then :)
plates? finished? mmmm supper... Where's the 3rd option; cheap and done?Isn't it cheap enough for you?
Never ;) Free, Now, and Good... Pik 2
sweet :thumb:
Looking forward to this GB! Been waiting on my GH60 plates forever, but that's never gonna get here.
Definitely in for one of each.
Fit [ ✔ by me, Cherry switches are a little lose, you may want to glue. Kailh and Gaterons fits perfectly. Combatible with ALPS(not Alps stabs)]
QuoteFit [ ✔ by me, Cherry switches are a little lose, you may want to glue. Kailh and Gaterons fits perfectly. Combatible with ALPS(not Alps stabs)]
Do the cherry switches pop out of the plate when you pull a keycap?
Oh well, it won't be much of a problem, I can probably just glue them :)
Well when the gb lauches just tell me and I'm in ;) been waiting for these for a long time! And now I also want those gateronsHehe. Great to hear!
I didn't follow this GB for a long times. New samples is very great. I like sandblast. Voted. Hope GB 'll run soon.Thanks! I am waiting for the Cherry stabilisers from Ortholinearkeyboards, when i get them, i will test the plates with these stabilisers to see if everything fits correctly. ETA is next week.
You're doing wonders with these plates. You should really consider PCBs next.You can easy to buy sprit 60% PCB.
You mean via sprit's group buy, or is it possible to get it outside of that?You're doing wonders with these plates. You should really consider PCBs next.You can easy to buy sprit 60% PCB.
Looking forward to this GB! Been waiting on my GH60 plates forever, but that's never gonna get here.
Definitely in for one of each.
Awesome! What kind of project are you thinking of using it with? :)
Via sprit's group buy.You mean via sprit's group buy, or is it possible to get it outside of that?You're doing wonders with these plates. You should really consider PCBs next.You can easy to buy sprit 60% PCB.
You're doing wonders with these plates. You should really consider PCBs next.Thanks! If I could design a PCB, I would love to sell them at a great price for you (I know some suppliers).
Cool!Looking forward to this GB! Been waiting on my GH60 plates forever, but that's never gonna get here.
Definitely in for one of each.
Awesome! What kind of project are you thinking of using it with? :)
I've been waiting a long time to make two 60% boards, one all white, one all black. Going to try to design and print my own case for it, but I would like to have plates for weight and stability :)
I'm not clear on why you can't hand wire and use spacers to put this in a standard case?You can. But I didn't learn about spacers until now :)
The fit of the cherry switches, would that be rectified by power coating the plate or is the fit that lose? If so what glue would one recommend?
Order placed.
I'm number 2 :)
:) Really looking forward to these.Thanks, I really appericate it!
Thanks for the hard work!
Thanks for running this!Thanks for supporting!
Hmmm...Any idea on what shipping to the USA will be from your haven in scandinavia?Shipping is stated in the order form. 10$ worldwide for one plate.
We just reached the MOQ for both plates, after under 24 hours!Go go go! :thumb:
Next price change is 20 plates sold, we need 3 more for ANSI and 10 more for ISO to tip :)
Quick and Simple is an excellent recipe for delivering a group buy on geekhack.:)
Ordered 1 ANSI plate! Thank you so much for doing this group buy :D
I missed that, thank you.Hmmm...Any idea on what shipping to the USA will be from your haven in scandinavia?Shipping is stated in the order form. 10$ worldwide for one plate.
I was able to combine the orders!I'm seeing your face on the Time Magazine.
:)I was able to combine the orders!I'm seeing your face on the Time Magazine.
Ordered 2 ISO. Now maybe finally I can do something with those Gateron switches I have lying around :D
Going to hopefully remember to order an ANSI plate once I get home, unfortunately I'm unable to access google docs at work. :'(
Going to hopefully remember to order an ANSI plate once I get home, unfortunately I'm unable to access google docs at work. :'(
Going to hopefully remember to order an ANSI plate once I get home, unfortunately I'm unable to access google docs at work. :'(
Same boat as you. I want a plate but need to a) figure out my order b) Can't access google docs at home.
ROUNDED CORNERS, OR NOT?How much rounded by the way?
Not sure, just a little bit to remove the sharp edge.ROUNDED CORNERS, OR NOT?How much rounded by the way?
Ordered 2 plates. One ANSI, one ISO.Thanks!
Awesome GB. :D
Going to hopefully remember to order an ANSI plate once I get home, unfortunately I'm unable to access google docs at work. :'(
You can order by PMing me :)
Placed my order, voting yes to random corners :)Thanks!
Thanks!Going to hopefully remember to order an ANSI plate once I get home, unfortunately I'm unable to access google docs at work. :'(
You can order by PMing me :)
Just ordered mine. :)
Is it possible to fix this problem by modifying the size? Did you measure the holes?
Fit [ ✔ by me, Cherry and Gaterons switches are a little lose, you may want to glue if you have thight keycaps and you want to remove them often. Kailh fits thightly. ALPS switches fits, but not thightly. MORE]
I prefer stability to compatibilityYes, you do, but this GB is not only for you.
For those who are ordering both? Is there a specific reason?I'm getting both because I own keycaps for both layouts and I'm eager to try the ANSI as I've only used ISO (IT) so far.
How does radius 2mm sound for the corners?About perfect to me.
That is cool!For those who are ordering both? Is there a specific reason?I'm getting both because I own keycaps for both layouts and I'm eager to try the ANSI as I've only used ISO (IT) so far.
I could say, it's for sake of testing.
I prefer stability to compatibilityYes, you do, but this GB is not only for you.
Am I not allowed to express an opinion about your product?Yes you can. Sorry about my answer. English isn't my first language so I didn't try to mock on you.
Because the answer that you just gave can be applied to any opinion expressed here.I prefer stability to compatibilityYes, you do, but this GB is not only for you.
Am I not allowed to express an opinion about your product?Yes you can. Sorry about my answer. English isn't my first language so I didn't try to mock on you.
Because the answer that you just gave can be applied to any opinion expressed here.I prefer stability to compatibilityYes, you do, but this GB is not only for you.
Great point, but as of this point, I cannot do such a major change to the design, but I will bring it with me for further reference.
Yeah I usually use UK ISO but I want to get a bit more into ANSI, though they moderately cheap so why not both? :thumb:Ordered 2 plates. One ANSI, one ISO.Thanks!
Awesome GB. :D
For those who are ordering both? Is there a specific reason?
So these plates have been tested with Alps?With ONE Apple extended switch, yes.
Sounds awesome :)Yeah I usually use UK ISO but I want to get a bit more into ANSI, though they moderately cheap so why not both? :thumb:Ordered 2 plates. One ANSI, one ISO.Thanks!
Awesome GB. :D
For those who are ordering both? Is there a specific reason?
If this drop is sucessful, will there be more in the future? I'm thinking about designs like 40% boards and such.Maybe, I dont know yet :)
Also you're doing some good work on here! Greets from germany.
I use 2.5mm radius on the corners of my plates. :)Do I get a copyright infringement if I choose 2,5mm or should I go with 2,4? :)
Spent some time on pexonpcs.co.uk yesterday, thinking about ordering the 60% case. Decided to order tomorow. Went back 5 minutes ago, sold out :eek:. Now where do I get a 60% case?
Done, thanks for the tip!
Spent some time on pexonpcs.co.uk yesterday, thinking about ordering the 60% case. Decided to order tomorow. Went back 5 minutes ago, sold out :eek:. Now where do I get a 60% case?Yea, I got the last one last night. Sorry! I guess this group buy is helping pexon as well...
Pexon is a friend so go on and support him :)Spent some time on pexonpcs.co.uk yesterday, thinking about ordering the 60% case. Decided to order tomorow. Went back 5 minutes ago, sold out :eek:. Now where do I get a 60% case?Yea, I got the last one last night. Sorry! I guess this group buy is helping pexon as well...
Grab this fast:Flawed items resemble me greatly so I bought one, thanks for the hint.
http://pexonpcs.co.uk/products/b-stock-items
Some aesthetics flaws, but i think you will be fine :)
Lel. They're gonna go fast.Grab this fast:Flawed items resemble me greatly so I bought one, thanks for the hint.
http://pexonpcs.co.uk/products/b-stock-items
Some aesthetics flaws, but i think you will be fine :)
Thanks for taking charge of 10 plates for yourself, that made me save €6.
Ordered 1 ISO plate.
Paid. :thumb:
paid. :)Awesome! Thanks.
Sorry if it has been asked but im too tired to read through the thread. Is this compatible with poker 2 and the original case? Hugs
Went to order, saw the discount code field. What's up with that?
Paid.Thanks, quochung :)
Wow wow wow hold on! Time to place an order! Thank Jebus I checked this thread today.Thanks. Talking with my supplier tomorrow or monday to start production :)
In for two of each my good man!
Paid for mine :)Super!
QuoteFit [ ✔ by me, Cherry switches are a little lose, you may want to glue. Kailh and Gaterons fits perfectly. Combatible with ALPS(not Alps stabs)]
Do the cherry switches pop out of the plate when you pull a keycap?
In most cases, yes :-/
There are some exceptions. They will only pull out of the plate if you really force it on a really short period of time. Gaterons and Kailhs are stuck in the plate.
QuoteFit [ ✔ by me, Cherry switches are a little lose, you may want to glue. Kailh and Gaterons fits perfectly. Combatible with ALPS(not Alps stabs)]
Do the cherry switches pop out of the plate when you pull a keycap?
In most cases, yes :-/
There are some exceptions. They will only pull out of the plate if you really force it on a really short period of time. Gaterons and Kailhs are stuck in the plate.
So Gaterons fit tightly? I'm hesitant to put in an order, I don't want to have to glue them or anything...
Paid! ^-^Thanks dude!
PaidThanks!
THE GATERON WINNER IS CHOSEN!
SPOILER ALERT:Morehttps://www.youtube.com/watch?v=Qz5jbTqsF_Q
Haha, next time :)THE GATERON WINNER IS CHOSEN!
SPOILER ALERT:Morehttps://www.youtube.com/watch?v=Qz5jbTqsF_Q
I am 49 position :eek:
Cool beans. Paid as well!Awesome!
**** think I missed the cutoff. Just put my order in. thanks leandren for running The buy.Will fix. :) NP
Paid! Now on the search for an appropriate case :) Thanks for the GB.Thanks!
The order is submited! Let get this going.
Last chance to put in orders(not gurranteed to get, first come, first serve) ! (will look at everything on Sunday).
Hopefully, they can start producing early next week.
Thanks for all the help and support. And congratsMorevitaLeewith the Gaterons!
L
Congrats! :) I hope you will enjoy!The order is submited! Let get this going.
Last chance to put in orders(not gurranteed to get, first come, first serve) ! (will look at everything on Sunday).
Hopefully, they can start producing early next week.
Thanks for all the help and support. And congratsMorevitaLeewith the Gaterons!
L
Woooohoooo!!! I can't believe I got picked up! :D
Super excited about my first build with this plate and switches.
Thanks for making this possible LeandreN!
Last chance now! Two places left. Also testing Cherry stabs. Seems to work fine, but they're a he to set up xD
You are in! Expect an invoice soonLast chance now! Two places left. Also testing Cherry stabs. Seems to work fine, but they're a he to set up xD
Hope I was just in time then ;D
You are in! Expect an invoice soonLast chance now! Two places left. Also testing Cherry stabs. Seems to work fine, but they're a he to set up xD
Hope I was just in time then ;D
Thanks!You are in! Expect an invoice soonLast chance now! Two places left. Also testing Cherry stabs. Seems to work fine, but they're a he to set up xD
Hope I was just in time then ;D
Received & paid, thanks!
So I guess I missed this. These allow for spring and stem swaps without desoldering right? They will work with plate mount switches, a la Poker II. If so Im interested if there are any left.
Okee...I just filled out the form I hit submit and it doesnt do anything. Hopefully Im not in there like 4 times. Did it work or did I not fill it out correctly? It looks right to me.
Cool thanksInvoiced!
I just placed an order for one ISO plate. Hope I'm not too late.
The form didn't let me proceed until I specified "0" as the number of ANSI plates, probably that's what happened to loki993.
And paid. Thanks!
I still got one ANSI to sellWell, I'll take it. You should already have my details for the invoice.
Thanks, I'll invoice you later.I still got one ANSI to sellWell, I'll take it. You should already have my details for the invoice.
Thanks, I'll invoice you later.Got it and paid.
Sorry for invoicing in €. Got the payment :)Thanks, I'll invoice you later.Got it and paid.
Do you know if it will support the Winkeyless b.face PCB? It has in-switch LEDs on the bottom of the switch whereas Poker has in-switch LEDs on the top side (stabiliser compatibility). I may grab another plate
Sorry for invoicing in €.It's the currency of my country. It's fine. Thanks.
Ohh, okay :)Sorry for invoicing in €.It's the currency of my country. It's fine. Thanks.
Can you send tracking number after you shipped plates?As I mentioned, I will IF tracking is available.
Thanks for putting all this together! I realize I probably should've looked into this *before* joining, but did you have an expected timeline for manufacturing/shipping to you?
As i mentioned in my last update, the supplier tells me that the manufacturing is soon ready. They will send over some pictures that i can show you. I asked them to take an extra quality control for you. The sandblasting looks sick.
I hope to get them sent to me next week and that they might arrive the week after that. I am trying my absolutely best to get it quick to you.
Thanks for putting all this together! I realize I probably should've looked into this *before* joining, but did you have an expected timeline for manufacturing/shipping to you?
Can you send tracking number after you shipped plates?As I mentioned, I will IF tracking is available.
No. I don't mean your post take a lot of my times. I only want say: "It is a little long post" & I don't have any implication. Pls don't understand my idea wrong.
In additional, thanks for your patient to explain more infos with me.
Hey LeandreN, missed this GB, if someone drops and you have a spare ISO plate let me know, I can pay quickly.I have one that haven't paid yet. I will let you know.
MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
:D
FIFO? First order In is First order Out
:p
Not quite sure what you mean here, but to clarify, this is one of the samples :)MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
:D
FIFO? First order In is First order Out
LIFO! :D
Not quite sure what you mean here, but to clarify, this is one of the samples :)MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
:D
FIFO? First order In is First order Out
LIFO! :D
Ohh, still not sure what you mean though, the SPRiT stuff was taken away from my account before buying the plates, so it's not like I am dealing with the GB money if that is what you think.Not quite sure what you mean here, but to clarify, this is one of the samples :)MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
:D
FIFO? First order In is First order Out
LIFO! :D
Yea cool, no worries. Just financial accounting, method of inventory valuation, how the goods flow in a company - FIFO (First in first out) or LIFO (last in first out)..
Ohh, still not sure what you mean though, the SPRiT stuff was taken away from my account before buying the plates, so it's not like I am dealing with the GB money if that is what you think.Not quite sure what you mean here, but to clarify, this is one of the samples :)MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
:D
FIFO? First order In is First order Out
LIFO! :D
Yea cool, no worries. Just financial accounting, method of inventory valuation, how the goods flow in a company - FIFO (First in first out) or LIFO (last in first out)..
Edit: did you talk about how I am going to ship stuff? (Last order first or first order first)?
If so, I am going to send everything at the same time :)
Thanks for explaining !Ohh, still not sure what you mean though, the SPRiT stuff was taken away from my account before buying the plates, so it's not like I am dealing with the GB money if that is what you think.Not quite sure what you mean here, but to clarify, this is one of the samples :)MoreShow Image(http://images.tapatalk-cdn.com/15/06/03/5daa009602e67fdf53b41a17a3b5efc0.jpg)Show Image(http://images.tapatalk-cdn.com/15/06/03/8101f3efd2a6ef339445369cd175d3d3.jpg)
:D
FIFO? First order In is First order Out
LIFO! :D
Yea cool, no worries. Just financial accounting, method of inventory valuation, how the goods flow in a company - FIFO (First in first out) or LIFO (last in first out)..
Edit: did you talk about how I am going to ship stuff? (Last order first or first order first)?
If so, I am going to send everything at the same time :)
[/quote ]
Yeah the edit.. I'm pretty sure he was referring to the order of shipments with regards to the list of people who had bought the plates. Seeing the gr8 samples he wants it first, real bad.
Haha, I'll try to ship everything at the same time. Maybe I'll to International orders one day and European the other if I have to split it.
:)
If you are going to send everything at the same time I want my package att the top of the pile ;)
Very nice LeandreN. What is that small plate in the middle?ISO numpad sample :) want to make an ISO numpad with a ISO enter key.
I was going to ask the same thing but now I have a better question - WHY? :)) That layout looks crazy, but I guess you have a plan...Very nice LeandreN. What is that small plate in the middle?ISO numpad sample :) want to make an ISO numpad with a ISO enter key.
Personal use, kinda strange, but I have a plan for the numpad.I was going to ask the same thing but now I have a better question - WHY? :)) That layout looks crazy, but I guess you have a plan...Very nice LeandreN. What is that small plate in the middle?ISO numpad sample :) want to make an ISO numpad with a ISO enter key.
Plates are looking good, I'll almost certainly be in on a later run when they support a non standard layout :)
Oh I see.What kind of projects are you working on ? :)
Finding 84 layout keyboard. It is primary but I still interested custom numpad. Only that I don't like handwire.Oh I see.What kind of projects are you working on ? :)
Now I regret not having joined in the first place.
I'd be happy about a plate, if there are people who changed their mind or don't pay.
Earlier requesters come first, of course.
Also anything new about PCB printing? You planning on starting GB for plates combined with PCBs?
I really want to set up a GB for a PCB, but i do not have the knowledge to design one.
Now I regret not having joined in the first place.I bought two ANSI and I can give one if LeandreN is ok with that (meaning refund me and sell it to you).
I'd be happy about a plate
Now I regret not having joined in the first place.I bought two ANSI and I can give one if LeandreN is ok with that (meaning refund me and sell it to you).
I'd be happy about a plate
I bought two ANSI and I can give one if LeandreN is ok with that (meaning refund me and sell it to you).
I will refund TalkingTree 20$ when i get the order from 3K.Ok with me.
Sound great ?
Either way I'll wait till tomorrow to fill out the order form, just in case you change your mind. (If that's not too late.)Your call, the offer is up.
Nice of you TalkingTree :)I will refund TalkingTree 20$ when i get the order from 3K.Ok with me.
Sound great ?Either way I'll wait till tomorrow to fill out the order form, just in case you change your mind. (If that's not too late.)Your call, the offer is up.
Please packing it carefully. Make sure that it can't bent during shipping.I have a label saying "DO NOT BEND" and I have packaged it as good as I can. Yours is sent BTW :)
This has to win the prize for best organized group buy on geekhack.Thank you so much :)
Well done and thank you. :)
Please packing it carefully. Make sure that it can't bent during shipping.I have a label saying "DO NOT BEND" and I have packaged it as good as I can. Yours is sent BTW :)
You were order number 16 :)Please packing it carefully. Make sure that it can't bent during shipping.I have a label saying "DO NOT BEND" and I have packaged it as good as I can. Yours is sent BTW :)
Oh oh awesome. Good job. I don't think I 'm in 16 first order.
I remembered I 'm at 29 in your Giveaway.
Anyway, thanks for your primary for me :thumb:
You were order number 16 :)Please packing it carefully. Make sure that it can't bent during shipping.I have a label saying "DO NOT BEND" and I have packaged it as good as I can. Yours is sent BTW :)
Oh oh awesome. Good job. I don't think I 'm in 16 first order.
I remembered I 'm at 29 in your Giveaway.
Anyway, thanks for your primary for me :thumb:
The order list has nothing to do with the giveaway list :)
No worries :) hope you get ur package fast :)You were order number 16 :)Please packing it carefully. Make sure that it can't bent during shipping.I have a label saying "DO NOT BEND" and I have packaged it as good as I can. Yours is sent BTW :)
Oh oh awesome. Good job. I don't think I 'm in 16 first order.
I remembered I 'm at 29 in your Giveaway.
Anyway, thanks for your primary for me :thumb:
The order list has nothing to do with the giveaway list :)
Oh really?
This is my lucky ha ha. I misunderstood about ordinal :/
No worries :) hope you get ur package fast :)You were order number 16 :)Please packing it carefully. Make sure that it can't bent during shipping.I have a label saying "DO NOT BEND" and I have packaged it as good as I can. Yours is sent BTW :)
Oh oh awesome. Good job. I don't think I 'm in 16 first order.
I remembered I 'm at 29 in your Giveaway.
Anyway, thanks for your primary for me :thumb:
The order list has nothing to do with the giveaway list :)
Oh really?
This is my lucky ha ha. I misunderstood about ordinal :/
Nice :DYou were number 1 :)
Order number 3 if I recall correctly
So the order of names at the beginning of the drawing video is the order you received them (and shipped them?). Does that mean my plates shipped?! *Happy Dance*It has nothing to do with the draw video. It is the order the plates were ordered :)
At the very beginning of that video you had your list of names that you copied into the randomizer. I thought that was the order in which you had received the... orders.
If you haven't sent mine yet, please include a doner from Balli off of Ubahn Alt-Tempelhof in berlin ;] I miss those so much X[Can you please explain?
If you haven't sent mine yet, please include a doner from Balli off of Ubahn Alt-Tempelhof in berlin ;] I miss those so much X[Leandren is based in Norway, so not really close to Berlin. Also sending food around isn't the best idea.
Thanks, I didn't understand a thing xDIf you haven't sent mine yet, please include a doner from Balli off of Ubahn Alt-Tempelhof in berlin ;] I miss those so much X[Leandren is based in Norway, so not really close to Berlin. Also sending food around isn't the best idea.
NORWAY! man, i thought you were german this whole time. well i guess that's cool too. send me some dolphin in that case.You should ask him to send lutefisk.
NORWAY! man, i thought you were german this whole time. well i guess that's cool too. send me some dolphin in that case.Haha, we don't have that much dolphin here, and you may get some problems with the customs.
Smells to bad to be shipped xDNORWAY! man, i thought you were german this whole time. well i guess that's cool too. send me some dolphin in that case.You should ask him to send lutefisk.
You were number 1 :)
Smells to bad to be shipped xDNORWAY! man, i thought you were german this whole time. well i guess that's cool too. send me some dolphin in that case.You should ask him to send lutefisk.
Please no. Surstrauming must be the most evil thing at this planet.
You were number 1 :)
Whoohoo :D I am no 1Smells to bad to be shipped xDNORWAY! man, i thought you were german this whole time. well i guess that's cool too. send me some dolphin in that case.You should ask him to send lutefisk.
Lutfisk doesn't smell that bad does it? Send him some http://en.wikipedia.org/wiki/Surstr%C3%B6mming (http://en.wikipedia.org/wiki/Surstr%C3%B6mming) .. :-X
Wow they look goodThanks :)
Im getting hyped
Everything is now shipped. Kind of strange posting 30 packages at a time, but the cashier thought it was fun.Wait you didn't ship mine did you? :X
Hope you get your package soon. Please post here when you receive it :)
You said I shouldn't ship it if it wouldn't come to you by the 18th. If I ship it today, you will have it early next week.Everything is now shipped. Kind of strange posting 30 packages at a time, but the cashier thought it was fun.Wait you didn't ship mine did you? :X
Hope you get your package soon. Please post here when you receive it :)
Ohh no thats fine, I just thought you might of forgotten :p please don't ship it :X yet anyway :pYou said I shouldn't ship it if it wouldn't come to you by the 18th. If I ship it today, you will have it early next week.Everything is now shipped. Kind of strange posting 30 packages at a time, but the cashier thought it was fun.Wait you didn't ship mine did you? :X
Hope you get your package soon. Please post here when you receive it :)
I have shipped it. Sorry if it wasn't clear. If you have some complications, I will solve it.Ohh no thats fine, I just thought you might of forgotten please don't ship it :X yet anywayYou said I shouldn't ship it if it wouldn't come to you by the 18th. If I ship it today, you will have it early next week.Everything is now shipped. Kind of strange posting 30 packages at a time, but the cashier thought it was fun.Wait you didn't ship mine did you? :X
Hope you get your package soon. Please post here when you receive it :)
No problem I have confused my self a bit anyway, hopefully it arrives or can be pushed through the door :XI have shipped it. Sorry if it wasn't clear. If you have some complications, I will solve it.Ohh no thats fine, I just thought you might of forgotten please don't ship it :X yet anywayYou said I shouldn't ship it if it wouldn't come to you by the 18th. If I ship it today, you will have it early next week.Everything is now shipped. Kind of strange posting 30 packages at a time, but the cashier thought it was fun.Wait you didn't ship mine did you? :X
Hope you get your package soon. Please post here when you receive it :)
I think it will :)No problem I have confused my self a bit anyway, hopefully it arrives or can be pushed through the door :XI have shipped it. Sorry if it wasn't clear. If you have some complications, I will solve it.Ohh no thats fine, I just thought you might of forgotten please don't ship it :X yet anywayYou said I shouldn't ship it if it wouldn't come to you by the 18th. If I ship it today, you will have it early next week.Everything is now shipped. Kind of strange posting 30 packages at a time, but the cashier thought it was fun.Wait you didn't ship mine did you? :X
Hope you get your package soon. Please post here when you receive it :)
Everythings seems perfect. You worked well.
The only thing is waiting & seeing our plates.... :cool:
Everythings seems perfect. You worked well.
The only thing is waiting & seeing our plates.... :cool:
Thanks quochung! I think you will be happy when you get your plate. It is absolutely gorgeous. Hope you get it soon.
L
What's in that bulky package?Let me guess.Show Image(http://images.tapatalk-cdn.com/15/06/11/a4d00d44b4b8482b4e2c42c22bc04285.jpg)
What's in that bulky package?Let me guess.Show Image(http://images.tapatalk-cdn.com/15/06/11/a4d00d44b4b8482b4e2c42c22bc04285.jpg)
My switches? :p
Thank you again for handling this so fast and flawlessly. :thumb:
Super job, LeandreN!Thanks :)
Plate(s) shipped, case from pexon arrived today, ready to build! Thanks!>Plates(s)
Hehe I know exactly what I ordered, one ISO one Ansi :)Yup :)
!Awesome! Thanks for posting :)
http://imgur.com/a/PWBwG
Wow, the finish looks really good!Thanks :)
Sorry that I sent you the first one ISO. Hope you are still satisfied :)Show Image(http://i.imgur.com/1R503Qi.jpg)
They arrived! Much earlier than expected :)
Sorry that I sent you the first one ISO. Hope you are still satisfied :)Show Image(http://i.imgur.com/1R503Qi.jpg)
They arrived! Much earlier than expected :)
OK, haha. Enjoy :)Sorry that I sent you the first one ISO. Hope you are still satisfied :)Show Image(http://i.imgur.com/1R503Qi.jpg)
They arrived! Much earlier than expected :)
They arrived at the same time, and I read your note. I'm really happy with the plates :D Thanks!
How about a 60% design with additional place for switches, that would allow the replacement of a fullsize space with a smaller one? That would be something new. (well, more or less)
So people would have more options on how to use the plate. Same with a design that allows ISO and ANSI in one plate. (Ducky got plates like that for example)MoreLeft - cut outs in the plate; Right - mounted switches + capsShow Image(http://abload.de/img/made_with_my_500_cad_1jbnd.png)
7bit got you covered. Just have to be patient... :-\How about a 60% design with additional place for switches, that would allow the replacement of a fullsize space with a smaller one? That would be something new. (well, more or less)
So people would have more options on how to use the plate. Same with a design that allows ISO and ANSI in one plate. (Ducky got plates like that for example)MoreLeft - cut outs in the plate; Right - mounted switches + capsShow Image(http://abload.de/img/made_with_my_500_cad_1jbnd.png)
Needs more stabs for the short spacebar but not a bad idea :) Can you buy 4u(?) spacebars to fit it though?
If you could discuss this in my IC for the second run, it would be nice.
Want to keep this thread nice and clean :)
If you could discuss this in my IC for the second run, it would be nice.
Want to keep this thread nice and clean :)
Yay, the plates arrived.. I will go and rave about them in the IC while I fill them with Gateron Browns.
Overall great GB, good job LeandreN :thumb:
My plate's here! Thanks, it's marvellous!
Got mine also today, mine got a little bent up it seems but should be easily put right looks really nice too just got fingerprints on it now :X Best order a PCB to build it then :p
On the topic of PCB, is there any "Ready to Built" PCB available that works with this plate? I want to handwire one plate but would like a pcb for the other one (just to try different things).
On the topic of PCB, is there any "Ready to Built" PCB available that works with this plate? I want to handwire one plate but would like a pcb for the other one (just to try different things).Satan GH60 from China, you can find it on Aliexpress.com
I've also received the plate (probably last saturday, but it was delivered at the office).
Protip: try to keep tape off the plate, it took a lot of scrubbing and isopropyl to get it right (because it stains like hell upon drying, had to clean it like 5/6 times before it was almost even):
(http://i.imgur.com/JzqC90tl.jpg) (http://imgur.com/JzqC90t)
Received my two ISO plates a few days ago.I will send you one ISO as compensation. (The last ones I have). I knew something had to go wrong.
Both plates look good, a minor bend but there was no problem bending it back.
Only thing i'm wondering about is why did you decide to tape both plates together? For one the tape is awful to get off and then all of the glue is left on the plate itself.
You can see on the image how the tape is on the plate, plus the glue left on the left side of the plate after i removed some of it.Show Image(http://i.imgur.com/sjgFIPK.jpg?1)
Other than that, both plates look good and the switches fit well, but I'm not looking forward to cleaning the glue residue off the plates....
Received my two ISO plates a few days ago.I will send you one ISO as compensation. (The last ones I have). I knew something had to go wrong.
Both plates look good, a minor bend but there was no problem bending it back.
Only thing i'm wondering about is why did you decide to tape both plates together? For one the tape is awful to get off and then all of the glue is left on the plate itself.
You can see on the image how the tape is on the plate, plus the glue left on the left side of the plate after i removed some of it.Show Image(http://i.imgur.com/sjgFIPK.jpg?1)
Other than that, both plates look good and the switches fit well, but I'm not looking forward to cleaning the glue residue off the plates....
The reason I taped them together was that I didn't want them to scratch with the other plate.
Refund for one. The other is being sent tomorrow. I have all your info.Received my two ISO plates a few days ago.I will send you one ISO as compensation. (The last ones I have). I knew something had to go wrong.
Both plates look good, a minor bend but there was no problem bending it back.
Only thing i'm wondering about is why did you decide to tape both plates together? For one the tape is awful to get off and then all of the glue is left on the plate itself.
You can see on the image how the tape is on the plate, plus the glue left on the left side of the plate after i removed some of it.Show Image(http://i.imgur.com/sjgFIPK.jpg?1)
Other than that, both plates look good and the switches fit well, but I'm not looking forward to cleaning the glue residue off the plates....
The reason I taped them together was that I didn't want them to scratch with the other plate.
Would really appreciate it, means I don't need to rush with cleaning and can spend my time getting every nook and cranny making sure it's properly done :).
The thought behind it is good and I understand the reasoning, but next time get some better quality tape that can be removed more easily.
Electrical or painters tape would probably be good bets, putting some cardboard between the plates would alleviate the issue as well.
Guess you already have my info, or do you want me to message you?
Refund for one. The other is being sent tomorrow. I have all your info.Received my two ISO plates a few days ago.I will send you one ISO as compensation. (The last ones I have). I knew something had to go wrong.
Both plates look good, a minor bend but there was no problem bending it back.
Only thing i'm wondering about is why did you decide to tape both plates together? For one the tape is awful to get off and then all of the glue is left on the plate itself.
You can see on the image how the tape is on the plate, plus the glue left on the left side of the plate after i removed some of it.Show Image(http://i.imgur.com/sjgFIPK.jpg?1)
Other than that, both plates look good and the switches fit well, but I'm not looking forward to cleaning the glue residue off the plates....
The reason I taped them together was that I didn't want them to scratch with the other plate.
Would really appreciate it, means I don't need to rush with cleaning and can spend my time getting every nook and cranny making sure it's properly done :).
The thought behind it is good and I understand the reasoning, but next time get some better quality tape that can be removed more easily.
Electrical or painters tape would probably be good bets, putting some cardboard between the plates would alleviate the issue as well.
Guess you already have my info, or do you want me to message you?
Thanks for letting me know :)
Got my plate today too! It was well packed and not really bent at all.Cherrys should fit. I have the exact plate and I am writing this on a Cherry stab keyboard.
There was just a little thing that bugged me... I underestimated Cherry once again.MoreShow Image(https://i.imgur.com/n7f72iP.jpg)
No, none of them fits.
Thank you for the great drop! Hope there will be more in the future.
Do what you want :)Refund for one. The other is being sent tomorrow. I have all your info.Received my two ISO plates a few days ago.I will send you one ISO as compensation. (The last ones I have). I knew something had to go wrong.
Both plates look good, a minor bend but there was no problem bending it back.
Only thing i'm wondering about is why did you decide to tape both plates together? For one the tape is awful to get off and then all of the glue is left on the plate itself.
You can see on the image how the tape is on the plate, plus the glue left on the left side of the plate after i removed some of it.Show Image(http://i.imgur.com/sjgFIPK.jpg?1)
Other than that, both plates look good and the switches fit well, but I'm not looking forward to cleaning the glue residue off the plates....
The reason I taped them together was that I didn't want them to scratch with the other plate.
Would really appreciate it, means I don't need to rush with cleaning and can spend my time getting every nook and cranny making sure it's properly done :).
The thought behind it is good and I understand the reasoning, but next time get some better quality tape that can be removed more easily.
Electrical or painters tape would probably be good bets, putting some cardboard between the plates would alleviate the issue as well.
Guess you already have my info, or do you want me to message you?
Thanks for letting me know :)
Thanks for the quick response and the compensation :).
Appreciate the refund but I'm already getting more than I paid for with an extra plate so I'm going to refund the refund unless it really offends you .
It was your first GB, as far as i know, and i bet it was stressful.
Mistakes will be made, all we can do is learn from them :)
How do they not fit?
Ohhh God, never do that again. Almost got a heart attack.How do they not fit?
They all have the wrong length, but that has nothing to do with the plate!
The short Cherry stabs fit really good actually.
Got mine, slight vertical bend (no problem) but the horizontal one is a *****, hopefully when screwed down it'll fit okLet me know how it goes. You can try laying something really heavy on it, and have it there over the night. Sorry about issues like this, the only thing I could do, is to invest money in packaging material, which I may end up doing for my next GB.
What alloy were these again? I wonder if they could be heat treated to make them less prone to bending.Stainless Steel 304, does that sounds wrong to you, I'll have to check it up in that case.
Probably not worth the cost, though.
Got mine, slight vertical bend (no problem) but the horizontal one is a *****, hopefully when screwed down it'll fit okLet me know how it goes. You can try laying something really heavy on it, and have it there over the night. Sorry about issues like this, the only thing I could do, is to invest money in packaging material, which I may end up doing for my next GB.
:)
Great :)Got mine, slight vertical bend (no problem) but the horizontal one is a *****, hopefully when screwed down it'll fit okLet me know how it goes. You can try laying something really heavy on it, and have it there over the night. Sorry about issues like this, the only thing I could do, is to invest money in packaging material, which I may end up doing for my next GB.
:)
Don't worry about it, I have a feeling it was my numpty delivery man squeezing it into out postbox. Mine will be powder coated at a later date so any tape issues or slight bending can be sorted by me.
Got mine yesterday. Some tape, some bending, no worriesThanks for posting :)
:thumb:
Got mine yesterday as well. I have to say, this is the nicest non colored finish I've had for my plates so far. As already mentioned above, the tape was also a remark on from my end. I don't notice big bending on my plates at first sight. Will post some pics if I don't forget.
Anyway, big thanks to LeandreN! Really quick GB, fast turnaround, good communication. I'll gladly take part in future groupbuys from you :thumb:
Got mine yesterday. :D
Minor horizontal bend, fixed by hand.
A little bit of tape on the left side but cleaned up that easily as well.
Some photos* (potato quality)
(Attachment Link)
(Attachment Link)
Super smooth Gaterons!
Super smooth group buy!
I'm worry about tape issue. Hope mine is not happen :-XYou ordered 1 plate so I don't think you will have that issue.
I wish you right :)I'm worry about tape issue. Hope mine is not happen :-XYou ordered 1 plate so I don't think you will have that issue.
Just got mine as well. A bit of tape on the edge, and a very slight horizontal curvature as well, but the bend is small enough that I'll probably end up bending it more trying to fix it. The one Cherry test key I have fits perfectly. :thumb:
Thanks!
What radius did you guys use for the corners? They look great!
Plates arrived, no bending, otherwise a little sticky ;DHope you are still satisfied :)
Some lovely plates :thumb:Thanks for the pictures :)Show Image(http://i.imgur.com/k4AgQt1.jpg)
Only the front and back plate had a little tape, nothing major. I'll clean them...some other time ;DShow Image(http://i.imgur.com/umxIqBk.jpg)
Great :)Got mine, slight vertical bend (no problem) but the horizontal one is a *****, hopefully when screwed down it'll fit okLet me know how it goes. You can try laying something really heavy on it, and have it there over the night. Sorry about issues like this, the only thing I could do, is to invest money in packaging material, which I may end up doing for my next GB.
:)
Don't worry about it, I have a feeling it was my numpty delivery man squeezing it into out postbox. Mine will be powder coated at a later date so any tape issues or slight bending can be sorted by me.
Also, you did only buy one plate, did it have any tape issues?
Unfortunately my two plates had a lot of residue on them. I will probably never clean anyway so its fine. I do have some issues with my cherry stabilizers not sittning thightly. I can easily dislodge them. Anyone else?I can send you an extra ISO if you want. Sorry for the residue that was entirely my fault.
I can send you an extra ISO if you want. Sorry for the residue that was entirely my fault.
I will probably glue my own, as I will never remove them. If you use a heat glue, you can remove it later if needed.
I can send you an extra ISO if you want. Sorry for the residue that was entirely my fault.
I will probably glue my own, as I will never remove them. If you use a heat glue, you can remove it later if needed.
NO! Do not send me a new plate. Its only glue, it comes off. Actually, i dont think you should offer people replacements since they are not broken. No one expects that of you. Just keep on with the awesomely smooth gb :)
.....And... Make an QFR/Filco compatible tkl plate <3
.....And... Make an QFR/Filco compatible tkl plate <3Are you thinking Phantom/Teensy or just a replacement plate so you have notches on QFR/Filco? I'm in the same boat myself. Been thinking of putting Phantom in my QFR-I, off-center caps lock and split right shift (if possible).
I had to cut a mini usb cable and solder the ends to the QFR USB board. So the mini usb cable connects to the teensy and the exposed wires are just soldered onto the QFR board. Wasn't too hard to do really and there's plenty of room in the case for everything.
I did notice one small problem with using a Phantom in a QFR case after after about 2 weeks of use. The plate and PCB do move slightly in the case if you travel with the keyboard or hit it hard on your desk. It's a pretty stiff move so it doesn't really bother me too much. I haven't found a good way to screw it to the case in a way where it won't do that. I think the problem is due to the fact that my stainless steel mounting plate is flat and the QFR requires curved edges. If you had the right plate or managed to find a way to use the QFR stock plate you probably wouldn't have a problem. Again, not really an issue that I care about... but it might bug some.
Plate arrived safe-and-sound. Just a little tape residue to clean in up on one end, but otherwise in perfect condition. Thank youLeandreN!
Mine just arrived, dead straight with no bends :cool:Arriving in outside Europe in less than a week? That's amazing.Show Image(http://i.imgur.com/GWHSOAg.jpg)
Mine just arrived, dead straight with no bends :cool:Show Image(http://i.imgur.com/GWHSOAg.jpg)
Yes it did have a little tap residue, but I was able to get it off easily with some soap and a sponge.
Yes it did have a little tap residue, but I was able to get it off easily with some soap and a sponge.Great!
I'm not a stamps collector but these ones look nice.Thanks for the detailed post :)Show Image(http://i.imgur.com/BBkxMAp.jpg)Show Image(http://i.imgur.com/fSDyZKx.jpg)
Picture with autograph!Show Image(http://i.imgur.com/pPewouf.jpg)
Sticky plates.Show Image(http://i.imgur.com/6eBxXxX.jpg)
After some cleaning I took the glue off, it might not be pretty but it's not sticky either.
This was my first GB and I'm very satisfied.
Yes it did have a little tap residue, but I was able to get it off easily with some soap and a sponge.
Oh really? This is very great. Thanks for your info :thumb:
Can you post picture after you solve issue?
I do have some issues with my cherry stabilizers not sittning thightly. I can easily dislodge them. Anyone else?
Thanks for explaining JD!I do have some issues with my cherry stabilizers not sittning thightly. I can easily dislodge them. Anyone else?
These are plate mounted stabilizers you are using, correct? Do they dislodge from the "top" part of the stabilizer hole? If so, that has to do with the design of the hole. That notch on the hole is for Costar stabilizer compatibility, but it's not present in the Cherry-only stabilizer hole design. It prevents the Cherry plate mount stabilizers from clipping onto the plate as they should, and therefore the stabilizers come out easily. It's a design compromise, for inclusion of Costar compatibility.
Yes it did have a little tap residue, but I was able to get it off easily with some soap and a sponge.
Oh really? This is very great. Thanks for your info :thumb:
Can you post picture after you solve issue?
The dark spots are from where I used the scruffy pad of the sponge. You could probably avoid the same results if you just use the soft side. It doesn't really matter for me though, I'll be painting my plate as well.Show Image(http://i.imgur.com/1tw8Lkz.jpg)
Interesting...Looks like its more bent than "a little uneven" I am sure you can get it 85% flat with your hands and just lay it under a heavy book or something over the night to get it straight. Sorry about the issue.Show Image(https://i.imgur.com/5hiHrm7.jpg)
Bent it back easily but its a little uneven now.. Bit of tape residue but there's no issue with that. Just wondering how I can make it completely flat.
It's fine, it's not your issue. Probably the silly US Mail system :)Interesting...Looks like its more bent than "a little uneven" I am sure you can get it 85% flat with your hands and just lay it under a heavy book or something over the night to get it straight. Sorry about the issue.Show Image(https://i.imgur.com/5hiHrm7.jpg)
Bent it back easily but its a little uneven now.. Bit of tape residue but there's no issue with that. Just wondering how I can make it completely flat.
It's fine, it's not your issue. Probably the silly US Mail system :)
It's pretty flat right now, just gonna put it under some books like you said and wait.
You will forgive the obscene photo quality, it's just to show how perfectly the plate fits into a Pexon's 60% case on a Satan GH60 PCB.That is great to hear. Awesome switch layout.Show Image(http://i.imgur.com/cnnDf96.jpg)
Already here, half way around the world!Cool. Glad you enjoyed! :)
So excited I already assembled one with a b.face board. Everything aligns perfectly.
http://imgur.com/a/L5rNh (http://imgur.com/a/L5rNh)
All soldered up. Very solid. Switches very snug.
Thank you LeandreN!
Already here, half way around the world!
So excited I already assembled one with a b.face board. Everything aligns perfectly.
http://imgur.com/a/L5rNh (http://imgur.com/a/L5rNh)
All soldered up. Very solid. Switches very snug.
Thank you LeandreN!
mind telling me what a b.face board is? Searching leads to confusing results :)http://winkeyless.kr/shop/
let me know how that Satan PCB works.Works well, it comes with a basic firmware already so it's ready to go. The only thing I've noticed is that the Cherry spacebar stabilizer gets easily stuck between PCB and place, I'm taking it out and getting a Costar stab for that. The 2u Cherry stabilizers work flawlessly.
let me know how that Satan PCB works.Works well, it comes with a basic firmware already so it's ready to go. The only thing I've noticed is that the Cherry spacebar stabilizer gets easily stuck between PCB and place, I'm taking it out and getting a Costar stab for that. The 2u Cherry stabilizers work flawlessly.
Ohh okey. Hav eyou clipped your Cherry stabs btw?Not yet but I'm trying since getting Costar stabs in Europe is rather hard and expensive. Maybe someone should consider running a groupbuy for them along with plates.
mind telling me what a b.face board is? Searching leads to confusing results :)http://winkeyless.kr/shop/
My plates arrived safe and sound, only a tiny bit of bending vertically (I expected to find them snapped in half by the postal service). I got too excited and didn't take any pictures before fitting everything together, but I'll post pictures of the one in progress when I get home! It took a tiny bit of fiddling to get them on around the stabilizers, but that was the only thing I noticed, other than that these are absolutely beautiful (and heavy). Thanks so much LeandreN!Haha! Great. Thanks for posting
Edit: I was surprised to find that my two plates weren't taped together, bonus win.
It's a design compromise, for inclusion of Costar compatibility.
Now all I need are all the other parts.I strongly recommend a Satan GH60 and a plastic 60% case (unless you prefer aluminum), you can find both on Aliexpress.
Thanks everyone for your advice. I 'll try to fix tape and bending issues. But about twisted esc position?
I afraid that I can't install switch on that position.
But about twisted esc position?Heat the corner with a heatgun or a lighter then squeeze a switch casing (without stem and spring) in the frame.
Thanks everyone help me to fix plate. Especially thanks to TakingTree & JD.
This is my plate after fixing:
https://flic.kr/s/aHskfypRQN
Thanks everyone help me to fix plate. Especially thanks to TakingTree & JD.Looks good! :thumb: Which PCB did you use?
This is my plate after fixing:
https://flic.kr/s/aHskfypRQN
Thanks everyone help me to fix plate. Especially thanks to TakingTree & JD.
This is my plate after fixing:
https://flic.kr/s/aHskfypRQN
Glad you get to fix it :)
Thanks everyone help me to fix plate. Especially thanks to TakingTree & JD.Looks good! :thumb: Which PCB did you use?
This is my plate after fixing:
https://flic.kr/s/aHskfypRQN
Thanks everyone help me to fix plate. Especially thanks to TakingTree & JD.
This is my plate after fixing:
https://flic.kr/s/aHskfypRQN
I only can fix around 90%, can't fix it perfect. But I think it can work well.
You should create new thread for Round 2.
Show Image(http://images.tapatalk-cdn.com/15/07/06/2cefc47d516751a9f3848f6182664c8b.jpg)
Planning next round :)
Still waiting on my round 1 plates to arrive. :'(That's unfortunate, I have definetily shipped it.
Interested in a aluminum plate. Going to keep an eye on this threadI'll make a new thread for GB 2, will link here when it is done.
Still waiting on my round 1 plates to arrive. :'(That's unfortunate, I have definetily shipped it.
I am afraid I can't do anything about the "lost in shipping" part, but I can maybe give you a compensation. I have no extra plates. If you don't want an ISO.
Please tell me, did you plan on handwriting or PCB. I have a PCB plate coming(could work with hand wiring with glue). A couple of weeks.
If you pay the shipping, I can send you one of the new anodized ones. It's a PCB plate. Sorry, but that package is probably lost.Still waiting on my round 1 plates to arrive. :'(That's unfortunate, I have definetily shipped it.
I am afraid I can't do anything about the "lost in shipping" part, but I can maybe give you a compensation. I have no extra plates. If you don't want an ISO.
Please tell me, did you plan on handwriting or PCB. I have a PCB plate coming(could work with hand wiring with glue). A couple of weeks.
Unfortunately no, was needing an ANSI plate. I checked with the post office again and no luck. Didn't really have any plans for the plate yet (just gathering parts) so at the time there was no preference for PCB or handwired plate.
That would be amazing, I know it's no fault of yours and more than likely an issue with the postal system here. I know you're going to be polling for colors but I'd love to see a purple one!Purple is available in round 2
That would be amazing, I know it's no fault of yours and more than likely an issue with the postal system here. I know you're going to be polling for colors but I'd love to see a purple one!Purple is available in round 2
Added it for your convenience.
Yes please. Also leave a note in the last field :)That would be amazing, I know it's no fault of yours and more than likely an issue with the postal system here. I know you're going to be polling for colors but I'd love to see a purple one!Purple is available in round 2
Added it for your convenience.
Awesome thank you, how do you want to handle this? Shall I submit an order on the round 2 gb page?