Recent Posts

Pages:  [1] 2 3 4 5 6 ... 10 »
1
Group Buys and Preorders / Re: [GB] Zlant 40% QMK Keyboard (shipped)
« Last post by historium on Mon, 16 July 2018, 11:36:53 »
If you ordered an un-soldered board, you will receive with your pcb a packet containing all of the components:

1. 1 x 32u4 microcontroller
2. 1 x crystal
3. 1 x 10uf capacitor (big orange one, polarized)
4. 1 x 1uf capacitor (thicker of the small white caps)
5. 2 x 22pf capacitors (thinner of the small white caps)
6. 2 x 10k ohm resistors
7. 2 x 22 ohm resistors
8. 1 x reset switch
9. 1 x usb jack
10. 50 x diodes

Here is a picture of the placement and polarity of all of the components. All diodes not pictured follow the same polarity.

(picture incoming, saved so I don't lose what I wrote)

I received mine today, could you upload that picture? Thanks

I will get it when I get home tonight.

lol

good thing that month long wait for the standoffs gave you time to prepare
2
Off Topic / Re: Vote for Trump
« Last post by tp4tissue on Mon, 16 July 2018, 11:35:59 »
3
Keyboard Keycaps / Re: GMK HyperFuse Origins Cap Stems Split
« Last post by starhacker on Mon, 16 July 2018, 11:35:19 »
Quite unusual to hear honestly.

What switches are you using?

You could contact Originative and see if they have replacements.

I am using Gateron Red switches. Are there MX clones that have issues fitting keycaps?
4
Off Topic / Re: Conspiracy Books
« Last post by tp4tissue on Mon, 16 July 2018, 11:33:32 »

I'm quite impressed if you're actually doing as such..

Tp4 recommends

committee of 300


and

creature of jekyll island


tp4tissue recommends conspiracy books in one thread... then denounces conspiracy books in another...

Show Image


Not Denounce..

Just Comical Cautioning..


Again, conspiracy theories are not baseless,  we do have a very small focused group of people with, rather way too much power, which is what those books go into.

However, we can't take those books as facts, because no one wore a wire..

They're well researched models of what MAY be the case.. and conforms to the common sense in terms of application.
5
Keyboards / Re: Say goodbye to rattling costar stabilizers - Band-Aid Mod
« Last post by Rumblehotep on Mon, 16 July 2018, 11:32:20 »
Every Costar stabilizer board should come with a roll of scotch tape.
6
Keyboard Keycaps / Re: GMK HyperFuse Origins Cap Stems Split
« Last post by xondat on Mon, 16 July 2018, 11:31:13 »
Quite unusual to hear honestly.

What switches are you using?

You could contact Originative and see if they have replacements.
7
Group Buys and Preorders / Re: [GB] Zlant 40% QMK Keyboard (shipped)
« Last post by ziptyze on Mon, 16 July 2018, 11:30:37 »
If you ordered an un-soldered board, you will receive with your pcb a packet containing all of the components:

1. 1 x 32u4 microcontroller
2. 1 x crystal
3. 1 x 10uf capacitor (big orange one, polarized)
4. 1 x 1uf capacitor (thicker of the small white caps)
5. 2 x 22pf capacitors (thinner of the small white caps)
6. 2 x 10k ohm resistors
7. 2 x 22 ohm resistors
8. 1 x reset switch
9. 1 x usb jack
10. 50 x diodes

Here is a picture of the placement and polarity of all of the components. All diodes not pictured follow the same polarity.

(picture incoming, saved so I don't lose what I wrote)

I received mine today, could you upload that picture? Thanks

I will get it when I get home tonight.
8
Keyboard Keycaps / GMK HyperFuse Origins Cap Stems Split
« Last post by starhacker on Mon, 16 July 2018, 11:29:19 »
After a week of use some of keycaps stems split in half. For now, I think only two caps are split from the top number row. Had to use super glue on the stems to keep them from breaking off completely. I expected a bit higher quality build for these caps. The stem borders are quite thin.

Any one else had breakage issues with GMK caps? Is there a way to get replacements?
9
Hasu this looks great! I would not recommend lasergist. Extremely slow and more expensive than laserboost with non existent customer support.
10
Classifieds / Re: [WTB] Orion TKL or OTD 360c, Octagon V2, Kingsaver
« Last post by yookwh on Mon, 16 July 2018, 11:25:31 »
Bump
Pages:  [1] 2 3 4 5 6 ... 10 »