Post by: jebbra on Sat, 05 November 2016, 12:08:03
- This time only Case B will run
- Case A will run after Case B is 100% done (including shipping)
- Case B will require smaller plate, which will be supplied in the buy later. Or you can cut/file the OLKB plate (2.5mm on each side) like I did for these prototype. I don't wanna widen the inner opening just to make it compatible to unmodified OLKB plate because it will make the gap between keycaps and case too wide especially compared to between keycaps, and that's against my design believe. And I can't make it 2 parts like KMAC did too because the small width the bezel has (and KMAC's plate have its own screw hole too).
- Case A will be redesigned to support unmodified OLKB plate by dividing it to 2 parts, Top Case and Bottom Case. The wide bezel on this case allowed the screw post to be implemented. Splitting it to 2 part design may increase the price but I still don't know yet because I want to focus on the Case B 1st and develop the Case A further after it (so for you who already soldered and love your Planck, please add some extra patient in the waiting time ^-^).
Case A
[attachimg=4]
[attachimg=5]
[attachimg=6]
Case B
[attachimg=7]
[attachimg=8]
[attachimg=9]
A high profile metal (still searching for available material) for Planck.
The thing about hipro case on Planck is it will look awkward in proportion because the nature size of Planck.
So to give an impression of slimmer case I make 2 designs, one inspired from Apple M0110A Keyboard and the other is inspired by Apple MacBook White Polycarbonate.
Please fill this form >>> https://goo.gl/forms/shPLUsCtqkxoOwyD2 <<<
If you like to get email notification regarding major update on this case!
Updated Case A (Apple M0110A)
[attachimg=2]
Updated Case B (MacBook Polycarbonate)
[attachimg=3]
I still working on the inner part for now, mimicking the original architecture of Planck milled case.
Update 1
Got a render for Case B
[attachimg=1]
Current status:
Revising 1st samples / Searching for coating vendor
Next move:
Get total quotation
Yay or nay?
Post by: Biggestmac on Sat, 05 November 2016, 14:03:29
Post by: tobsn on Sat, 05 November 2016, 19:17:01
Post by: menuhin on Sun, 06 November 2016, 07:00:06
(Shouting out for a Purple color case!)
But will be $$$
Post by: jebbra on Mon, 07 November 2016, 00:39:56
Looking good!
Thank you!
super yay! I need those 3d files... :D
:thumb: do you need the raw file or?
It looks real good, I hope there'll be as many options of color as offered by OLKB.com.
But will be $$$
My goal is around $50 each. With this kind of GB color will be based on demand, I don't have spare money to make all the colors in stock :cool:
Post by: jchan94 on Mon, 07 November 2016, 01:19:52
Post by: olieatstofu on Mon, 07 November 2016, 05:40:21
I'm definitely interested, and great price point! :-*
Post by: tobsn on Mon, 07 November 2016, 09:58:35
super yay! I need those 3d files... :D
:thumb: do you need the raw file or?
you serious? :D
any format will do :)
Post by: funderburker on Mon, 07 November 2016, 10:14:45
A high profile metal (still searching for available material) for Planck.
The thing about hipro case on Planck is it will look awkward in proportion because the nature size of Planck.
So to give an impression of slimmer case I make 2 designs, one inspired from Apple M0110A Keyboard and the other is inspired by Apple MacBook White Polycarbonate.
Case A (Apple M0110A)
(Attachment Link)
Case B (MacBook Polycarbonate)
(Attachment Link)
I still working on the inner part for now, mimicking the original architecture of Planck milled case.
Update 1
Got a render for Case B
(Attachment Link)
==============================
Current status:
Working on inner parts
Next move:
Get quotation from vendor
==============================
Yay or nay?
Oh man, that last pic/render looks awesome! What keyset is that if there is one? Now I really want a 40% again. Damn you GH!
Post by: pixelpusher on Mon, 07 November 2016, 10:59:15
Post by: Fictiouz on Mon, 07 November 2016, 11:58:28
Post by: menuhin on Mon, 07 November 2016, 12:11:12
(Oh, for the upcoming Sub-Atomic too!)
Post by: gnmar2723 on Mon, 07 November 2016, 22:20:56
At first I thought it was the QS Series Planck keyset from UKKeycaps (http://www.ukkeycaps.co.uk/product/qs-series-double-shot-planck-keyset) but jebbra has stated otherwise on reddit. (https://www.reddit.com/r/MechanicalKeyboards/comments/5br52c/ic_planck_high_profile_bottom_case/) Either way, I really want it to be a thing. It looks so classy, like 9009.A high profile metal (still searching for available material) for Planck.
The thing about hipro case on Planck is it will look awkward in proportion because the nature size of Planck.
So to give an impression of slimmer case I make 2 designs, one inspired from Apple M0110A Keyboard and the other is inspired by Apple MacBook White Polycarbonate.
Case A (Apple M0110A)
(Attachment Link)
Case B (MacBook Polycarbonate)
(Attachment Link)
I still working on the inner part for now, mimicking the original architecture of Planck milled case.
Update 1
Got a render for Case B
(Attachment Link)
==============================
Current status:
Working on inner parts
Next move:
Get quotation from vendor
==============================
Yay or nay?
Oh man, that last pic/render looks awesome! What keyset is that if there is one? Now I really want a 40% again. Damn you GH!
Post by: drakeonyou on Tue, 08 November 2016, 03:44:20
Post by: r5d on Tue, 08 November 2016, 07:39:29
Post by: jebbra on Tue, 08 November 2016, 08:26:35
Case A
[attachimg=1]
Case B
[attachimg=2]
Already submit them to vendor, now waiting on quotation.
Anyway, please fill this form for email newsletter about major update!
>>> https://goo.gl/forms/shPLUsCtqkxoOwyD2 (https://goo.gl/forms/shPLUsCtqkxoOwyD2) <<<
Post by: slot demon on Tue, 08 November 2016, 08:56:11
Post by: jebbra on Tue, 08 November 2016, 09:29:32
I approve of the Case A (Apple M0110A. I may not like the planck, but that case is ballah.Still not sure tho, I'm afraid it will make it kinda bulky..
As a future owner of a planck I've always wondered "who will create a high profile for this beaut" and here we are.Let's hope (and gather more people) for this price!
I'm definitely interested, and great price point! :-*
The file is on my friend's and he is out of town for...I don't know when.. What exactly you need? The light setting or the assets or?super yay! I need those 3d files... :D
:thumb: do you need the raw file or?
you serious? :D
any format will do :)
Oh man, that last pic/render looks awesome! What keyset is that if there is one? Now I really want a 40% again. Damn you GH!The keyset is another project I'm working on, will reveal it around new year :thumb:
Beautiful case.Thank you!
I might need to replace my Planck just for this case.. still have a hand-wired one kicking from 2014 :pJust make it a split Planck with them :cool:
And please collaborate with Jackhumbert if possible!Already sir. I'm in contact with him to cross checking :thumb:
(Oh, for the upcoming Sub-Atomic too!)
For Sub-Atomic, I can't say anything since the keyboard itself still in the middle of design.
At first I thought it was the QS Series Planck keyset from UKKeycaps (http://www.ukkeycaps.co.uk/product/qs-series-double-shot-planck-keyset) but jebbra has stated otherwise on reddit. (https://www.reddit.com/r/MechanicalKeyboards/comments/5br52c/ic_planck_high_profile_bottom_case/) Either way, I really want it to be a thing. It looks so classy, like 9009.When I look at 9009 it sure give the same calm vibe, but I believe it will be different in the end.
Great cases, loving both designs! Could you offer Planck PCBs as well in the GB for a complete kit? The case has its own plate anyway since the olkb plate is a tad too big, right?Yes most likely this will be sold bundled with its own plate. I know it will hurt people which already owned and soldered their Planck, but I can't make solution for compatibilty with standard plate, for now.
I like the second really much and if you can provide them at 50$ it would be a dream.Spread the word and (maybe) this won't be just a dream!
Post by: tobsn on Tue, 08 November 2016, 11:09:48
The file is on my friend's and he is out of town for...I don't know when.. What exactly you need? The light setting or the assets or?
STL 3d data would be best :D
Post by: UsualSuspectXXX on Tue, 08 November 2016, 20:41:23
Post by: jebbra on Wed, 09 November 2016, 01:54:38
[attachimg=1]
Post by: SlamnFunc on Wed, 09 November 2016, 06:37:24
Sudden message from Vendor :eek:
(Attachment Link)
Oh Wow!!! I don't know what they are saying but that looks beautiful :eek:
Post by: tobsn on Wed, 09 November 2016, 07:58:15
(https://dl.dropboxusercontent.com/s/wbncjbu08yk41w7/2016-11-09%20at%202.56%20PM.png)
Post by: funderburker on Wed, 09 November 2016, 08:04:33
What I don't understand are the raised parts and the deep cut out near the plug cutoutShow Image(https://dl.dropboxusercontent.com/s/wbncjbu08yk41w7/2016-11-09%20at%202.56%20PM.png)
As I understand the deep cutout is for a teensy if you go for handwired build. Other raised parts are probably PCB supports.
Post by: tp4tissue on Wed, 09 November 2016, 09:00:47
What I don't understand are the raised parts and the deep cut out near the plug cutoutShow Image(https://dl.dropboxusercontent.com/s/wbncjbu08yk41w7/2016-11-09%20at%202.56%20PM.png)
As I understand the deep cutout is for a teensy if you go for handwired build. Other raised parts are probably PCB supports.
yea raised part supports the pcb..
buhhhh... I think the top should be filleted..
The bottom of the pegs are fine , but if you're machining that you would need a ball nose, and it doesn't really do anything, even 4mm of aluminum is plenty strong without that corner radius..
I don't think there should be any Round corners on the pegs at all, because you guys have to remember, cnc curves are not actually round, it's kind of an illusion. and if you round it, there's just more finishing involved to make it look smooth..
Square pegs without corner radius would be the fastest and with filleted top.
IN FACT, I think you should remove all the pegs, and just tap holes..
Then machine all the pegs separately and just m3 screw it in.. hahahahaha
Post by: jebbra on Wed, 09 November 2016, 10:50:14
Post by: blackriver on Wed, 09 November 2016, 14:24:43
Post by: hoq on Wed, 09 November 2016, 18:50:41
Post by: tobsn on Thu, 10 November 2016, 07:58:56
What I don't understand are the raised parts and the deep cut out near the plug cutoutShow Image(https://dl.dropboxusercontent.com/s/wbncjbu08yk41w7/2016-11-09%20at%202.56%20PM.png)
As I understand the deep cutout is for a teensy if you go for handwired build. Other raised parts are probably PCB supports.
yea raised part supports the pcb..
You guys are sure about this? it seems a bit silly to rest a PCB on metal... alu or not - because of soldering points etc.
Then machine all the pegs separately and just m3 screw it in.. hahahahahaPlanck PCB is M2
Post by: jebbra on Sat, 12 November 2016, 21:14:59
Anyway, 1st sample of The Case A!
[attachimg=1]
The only thing I want to revise is the USB hole, which is a bit tight.
[attachimg=2]
Post by: brizzzle on Sun, 13 November 2016, 10:50:33
Post by: gnmar2723 on Mon, 14 November 2016, 18:50:12
Post by: tobsn on Wed, 16 November 2016, 05:14:55
Post by: jebbra on Wed, 16 November 2016, 06:28:13
Both samples are done, hopefully I will get them on my hands tomorrow! I'm super excited :p
If you need help, send me the STL and possibly a board model and I can have someone look at it who does that (award winning) for a living ;)
Damn mate I still owe you the file. PM me your email I will send to you the STL I use for samples tonight.
Post by: Fictiouz on Wed, 16 November 2016, 06:30:59
Post by: jebbra on Fri, 18 November 2016, 01:10:59
If you need help, send me the STL and possibly a board model and I can have someone look at it who does that (award winning) for a living ;)
Already emailed you bud :thumb:
The fact that you updated to support handwiring may have just made you another sale :p
I intend to do it from the start, but I don't know the exact measurement needed. Will have a Teensy 2.0 on my hand in a couple days and will further update (if any) the measuremet from that.
Post by: Danilo_dk on Sun, 20 November 2016, 05:30:34
On that second photo you can see a ridge along the middle of the case. Will that also be present on the final product? Did you make these cases compatible with the normal plate sold through olkb.com, or did you assemble the Plancks you took to the meetup after you got the prototype cases?
I am dying to see the small bevel case in black or dark gray. That will most certainly be the one I will get.
Post by: jebbra on Sun, 20 November 2016, 22:19:47
I saw you took the cases to the Jakarta meetup. They look pretty good. Here is a link to the photo for anyone that missed them http://i.imgur.com/N3WBJjc.jpg. Oh, and here is another one http://i.imgur.com/Z9ck3FW.jpg. I found both in albums linked on Reddit.
On that second photo you can see a ridge along the middle of the case. Will that also be present on the final product? Did you make these cases compatible with the normal plate sold through olkb.com, or did you assemble the Plancks you took to the meetup after you got the prototype cases?
I am dying to see the small bevel case in black or dark gray. That will most certainly be the one I will get.
Obviously any surface will be cleaned from ridges and marks! The one on visible on the photo is due the wrong step on milling and because of that we now know how to handle it. I want to show them to more people and get their input before I move to the next step.
Here's some fact and plan:
- Case B will require smaller plate, which will be supplied in the buy later. Or you can cut/file the OLKB plate (2.5mm on each side) like I did for these prototype. I don't wanna widen the inner opening just to make it compatible to unmodified OLKB plate because it will make the gap between keycaps and case too wide especially compared to between keycaps. And I can't make it 2 parts like KMAC did too because the small width the bezel has (and KMAC's plate have its own screw hole too).
- Case A will be redesigned to support unmodified OLKB plate by dividing it to 2 parts, Top Case and Bottom Case. The wide bezel on this case allowed the screw post to be implemented. Splitting it to 2 part design may increase the price but I still don't know yet because I want to focus on the Case B 1st and develop the Case A further after it.
Post by: gnmar2723 on Sun, 20 November 2016, 22:23:02
Post by: jebbra on Mon, 21 November 2016, 05:24:47
Case A
[attachimg=1]
More
[attachimg=2]
[attachimg=3]
[attachimg=3]
Case B
[attachimg=4]
More
[attachimg=5]
[attachimg=6]
[attachimg=6]
Obviously this baby still far from perfect as there will be 3 steps, CNC forming, CNC finishing, and coating (anodize/powder coat) and this sample only been through 1st step (CNC forming) plus I encounter some problem in the set up fo some holding marks are very visible.
Now the announcements:
Like I said on previous post, this round only Case B will be made, and it will come with spesific universal plate (Grid, MIT, and 1.25–1.25–1.25–1.25–2u/2x 1u–1.25–1.25–1.25–1.25 Bottom Row). And this case can't be used with OLKB's plate unless you cut/filed it (like I do)
Why?
Because I will develop Case A further into 2 parts case to support OLKB's plate (so for you who already soldered and love your Planck, please add some extra patient ^-^)
Then the question:
I still can't find a good anodizing vendor here, personally it is okay for me going with powder coating (and I like it more because powder coat can give similar matte finish like keycaps do, thus making the whole keyboard feel uniform in texture).
What do yo think about powder coating?
Let's poll! >>> http://www.strawpoll.me/11700415
Post by: menuhin on Mon, 21 November 2016, 06:41:19
Post by: tobsn on Mon, 21 November 2016, 07:05:03
would be nice if you'd round those edges a tiny bit, similar to case A :D
Post by: Danilo_dk on Mon, 21 November 2016, 07:29:58
Will the plate for this case support switch top removal? That is one of the most valued things of the standard OLKB plate in my opinion. I have opened my switches many times.
Post by: cygnusx1_ on Mon, 21 November 2016, 10:51:49
Post by: olieatstofu on Mon, 21 November 2016, 16:44:18
I actually like the look of the sharp edge on case B. But it would probably make sense to round it over just a bit so you won't hurt yourself on it.
Will the plate for this case support switch top removal? That is one of the most valued things of the standard OLKB plate in my opinion. I have opened my switches many times.
I agree, I love the way case b is at the moment. I think smoothing the lines would be nice, but curving them maybe not.
Can't WAIT for this!
Post by: funderburker on Mon, 21 November 2016, 17:09:12
Show Image(https://dl.dropboxusercontent.com/s/05bz7phkwo2hqzv/2016-11-21%20at%202.04%20PM.jpg)
would be nice if you'd round those edges a tiny bit, similar to case A :D
Damn! Need to get me a Planck.
Post by: jebbra on Mon, 21 November 2016, 19:30:45
If I want a case that support something like a staggered Planck keyboard PCB also (sold in the past also at OLKB), then I think A is better?As long as the dimension and USB placement of it is the same as recent OLKB plate, you are good to go.
Post by: breckstar on Mon, 21 November 2016, 23:03:30
Post by: ndlu2 on Mon, 21 November 2016, 23:55:07
Post by: menuhin on Tue, 22 November 2016, 02:57:25
If I want a case that support something like a staggered Planck keyboard PCB aka Quark (sold in the past also at OLKB), then I think A is better?
Post by: Danilo_dk on Tue, 22 November 2016, 11:58:07
If anyone else is interested in a carbon fiber plate, there is currently an interest check over on Reddit. Initially there was not going to be a plate compatible with this high profile case, but after suggesting it to the OP he said he could do it.
So if anyone else wants it to happen as well, head over to this Reddit thread and select "Smaller planck plate for compatibility with high profile case" in the form. https://www.reddit.com/r/MechanicalKeyboards/comments/5e8mat/ic_carbon_fiber_plates/
Post by: nathanrosspowell on Tue, 22 November 2016, 12:07:54
Post by: menuhin on Tue, 22 November 2016, 12:54:23
Hey everyone,
If anyone else is interested in a carbon fiber plate, there is currently an interest check over on Reddit. Initially there was not going to be a plate compatible with this high profile case, but after suggesting it to the OP he said he could do it.
So if anyone else wants it to happen as well, head over to this Reddit thread and select "Smaller planck plate for compatibility with high profile case" in the form. https://www.reddit.com/r/MechanicalKeyboards/comments/5e8mat/ic_carbon_fiber_plates/
"this high profile case" - you mean case A or case B?
Post by: pattulus on Tue, 22 November 2016, 13:07:50
(http://uploads.tapatalk-cdn.com/20161122/e47069f2cb6fa8eab48633d80bd05a7b.jpg)
Also: can you update the image links on post #1 — maybe a Tapatalk issue, but I can only see one image.
Post by: menuhin on Tue, 22 November 2016, 13:27:46
So, to clarify this: I can just drop my existing Planck like it is (see picture) into that case without removing any parts?Show Image(http://uploads.tapatalk-cdn.com/20161122/e47069f2cb6fa8eab48633d80bd05a7b.jpg)
Also: can you update the image links on post #1 — maybe a Tapatalk issue, but I can only see one image.
I guess not, case A should work with existing plate, while case B needs doesn't fit that MIT/grid plate from olkb.com and needs a plate specially made for this case B.
For you, you need to desolder all your switches from the PCB and then fit in the specially made new plate for case B, and then solder all the switches back in the PCB again before you can use case B.
Case A seems to be a design for lazy people like me.
Post by: Danilo_dk on Tue, 22 November 2016, 13:35:39
"this high profile case" - you mean case A or case B?
I mean case A, yes. The plate for that one needs to be just a bit smaller than the standard one provided my OLKB.
I guess not, case A should work with existing plate, while case B needs doesn't fit that MIT/grid plate from olkb.com and needs a plate specially made for this case B.
For you, you need to desolder all your switches from the PCB and then fit in the specially made new plate for case B, and then solder all the switches back in the PCB again before you can use case B.
Case A seems to be a design for lazy people like me.
Filing down the existing plate should also work.
Post by: menuhin on Tue, 22 November 2016, 16:10:29
"this high profile case" - you mean case A or case B?
I mean case A, yes. The plate for that one needs to be just a bit smaller than the standard one provided my OLKB.I guess not, case A should work with existing plate, while case B needs doesn't fit that MIT/grid plate from olkb.com and needs a plate specially made for this case B.[/spoiler]
For you, you need to desolder all your switches from the PCB and then fit in the specially made new plate for case B, and then solder all the switches back in the PCB again before you can use case B.
Case A seems to be a design for lazy people like me.
Filing down the existing plate should also work.
Approximately how much filing? Can it be done simply by hand?
I do think case B look really good, and have to consider how much work and its compatibility. Case A looks a bit like the Ducky mini case to me, still look good.
Post by: roostrc0gburn on Tue, 22 November 2016, 17:07:51
Post by: jebbra on Tue, 22 November 2016, 19:53:48
"this high profile case" - you mean case A or case B?
I mean case A, yes. The plate for that one needs to be just a bit smaller than the standard one provided my OLKB.I guess not, case A should work with existing plate, while case B needs doesn't fit that MIT/grid plate from olkb.com and needs a plate specially made for this case B.
For you, you need to desolder all your switches from the PCB and then fit in the specially made new plate for case B, and then solder all the switches back in the PCB again before you can use case B.
Case A seems to be a design for lazy people like me.
Filing down the existing plate should also work.
If you want Case A then you don't really need smaller plate, because I intend to make it the one which will support OLKB's plate by making it a 2 pieces case (top & bottom). But Case A will be made after Case B finished the GB phase as I need to learn how it works.
Post by: jebbra on Tue, 22 November 2016, 19:57:04
can we order a raw case for anodizing our selves?Yes I'm quite sure you can order it barebone without any coating. I'll meet with the vendor today and bring this topic.
Post by: pattulus on Tue, 22 November 2016, 22:23:19
Post by: jebbra on Tue, 22 November 2016, 22:58:13
Thanks for answering the question (again). I see now that it already has been asked and answered (https://geekhack.org/index.php?topic=85663.msg2306236#msg2306236) – looks like I didn't get an update on my phone otherwise I wouldn't have posted in the 1st place :-[
No biggies, I will asked whatever in my head too if it's about something I care :thumb:
Post by: olieatstofu on Sat, 26 November 2016, 16:01:44
Post by: jebbra on Sat, 03 December 2016, 09:16:18
To ask a burning question, what's the difference between powder and anodised coating?As far as I know, it only the looks that differ them, anodize keeps the metallic looks of the metal beneath it while powder coating makes it, well, painted. Maybe in deeper spec they differ but as long as the thing is only sit on your desk, the strength is equal. And tbh in my place, powder coating is more expensive than anodize, and they said powder coating is more superior in term of durability.
Post by: jebbra on Sat, 03 December 2016, 09:23:02
So today I went to the coating vendor and didn't satisfied looking at their anodize sampling. But the powder coating is looking good and stupidly, I didn't take any pic... Will sample them anyway next week, on the plate with same sandblasted material (Alu T6061) as the case and the same dimension.
The question is, which color pallete should I sample? The 4 neutral color will surely be sampled, but another 4 is still in question, 'normal' color or pastel one? I'm interested in pastel tbh because that color can only happen in powder coating.
Normal
[attachimg=1]
Pastel
[attachimg=2]
Post by: Danilo_dk on Sat, 03 December 2016, 09:58:29
Post by: olieatstofu on Sat, 03 December 2016, 13:24:52
Sorry for the idle, been crazy at my studio lately :-X
So today I went to the coating vendor and didn't satisfied looking at their anodize sampling. But the powder coating is looking good and stupidly, I didn't take any pic... Will sample them anyway next week, on the plate with same sandblasted material (Alu T6061) as the case and the same dimension.
The question is, which color pallete should I sample? The 4 neutral color will surely be sampled, but another 4 is still in question, 'normal' color or pastel one? I'm interested in pastel tbh because that color can only happen in powder coating.
Normal
(Attachment Link)
Pastel
(Attachment Link)
I do like the lighter colours, as you said, it'll give this case a unique look and feel.
That pale green will look good against those keycaps you're planning ; - )
Post by: jchan94 on Sat, 03 December 2016, 13:53:53
It needs a better finish and looks raw atm.
But good job :D
Post by: jebbra on Sat, 03 December 2016, 20:38:33
So does that mean that there won't be a full on black option? I am not the person that wants a bright or colorful case for my keyboard, so the darker the better in my opinion.
There will be! Sorry I forgot to add that, my bad :'(
Sorry for the idle, been crazy at my studio lately :-X
I do like the lighter colours, as you said, it'll give this case a unique look and feel.
That pale green will look good against those keycaps you're planning ; - )
The rule thumb of case color is match the keycaps alphas so oyster white will be the best match. But rules are meant to be broken :cool:
Super don't own a planck or plan to, but Case A would be my choice.
It needs a better finish and looks raw atm.
But good job :D
Thanks!
Yeah this progress is quite slow because I work on it in my free time plus this is my very first time choosing alu, visiting CNC vendor, searching finish, etc so please bear with me :p
Post by: menuhin on Sun, 04 December 2016, 02:20:39
I have heard it is difficult t make scratch marks on hard anodized alu case, is it true? And how is it different from Jon-hard anodizing?
Post by: jebbra on Sun, 04 December 2016, 21:36:27
What is powder coating?
I have heard it is difficult t make scratch marks on hard anodized alu case, is it true? And how is it different from Jon-hard anodizing?
Basically paint, but impelemented in powder form and then baked to make it super stick to the material beneath it.
This is what powder coat looks like on keyboad:
Norbaurer's Aluminum CM case (https://shop.norbauer.com/products/custom-cnc-aluminum-case-for-coolermaster-novatouch-rapid-i-and-masterkeys-keyboards?variant=27198514952)
(https://cdn.shopify.com/s/files/1/1571/5135/products/untitled-3928_1024x1024.jpg?v=1478320007)
Dorkvader's Model F
(https://farm8.staticflickr.com/7638/16668469069_b6b8c149d4_o.jpg)
(https://farm9.staticflickr.com/8638/16855379845_ccbf179b13_o.jpg)
Rama M10-A Prototype
(https://i.imgur.com/JhKcDEl.jpg)
Powder Coat vs Anodize
Why I intend to not choosing anodize is because the ones available around my area is only decorative anodize, not hard anodize or other mid-high quality anodize.
Post by: Danilo_dk on Mon, 05 December 2016, 01:50:59
If they are both equal when it comes to durability, wear, and such, I see no reason to just go with the one that is more readily available for you. And since you say you can't find a place that does high quality anodization, I would go for powder coating.
Post by: PollandAkuma on Mon, 05 December 2016, 13:18:37
I'd love a sample of the normal colours except for the the traffic blue. Light blue would be rad!
On second thought the traffic blue would go well with my Modern Selectric!
Post by: jebbra on Tue, 06 December 2016, 06:28:45
So the main cosmetic difference I see between anodizing and powder coating is that one remains shiny like the bare material is, while the other is matte. Strange though, as the standard Planck case is also anodized, but that one is matte.
If they are both equal when it comes to durability, wear, and such, I see no reason to just go with the one that is more readily available for you. And since you say you can't find a place that does high quality anodization, I would go for powder coating.
I try to scratch the powder coat with my nails and it hold still, scratch it with my bike key and it start to peel bit by bit, well, even anodize on a MacBook will scratched if you run another metal on top of it so yeah, durability is good. The red fire hydrant on the side road is a good example of powder coat on metal.
Seems like why peeps on mechkey prefer anodize is because it still "looks metal" because the material is what differentiate custom keyboard from mass-manufactured one and people want to show it off via pictures.
Good news is, my friend told me there is a workshop in the next city that do Hard Anodize (Type III). Already contacted them and will send them some plate with same material and dimension to see their quality.
Now that planck is in my options, I'd definitely want a hi-pro case. I hate the normal case.
I'd love a sample of the normal colours except for the the traffic blue. Light blue would be rad!
On second thought the traffic blue would go well with my Modern Selectric!
While I really want a new wave of color (pastel on this case) to be introduced to mechkey community, I find it lack the supporting keycaps with same saturation to pair it :-[ that's why almost whatever keyset we all have up till now will only can be matched with standard color. The only key color to match pastel one is standard color like white, black and gray but I doubt gray will do it.
My other project is a keyset in pastel color scheme (the one I use in initial mockup render) in an effort to refresh the color game in mechkeys :thumb:
(yes the color will be custom, not using SP's color chip).
Post by: menuhin on Tue, 06 December 2016, 08:20:26
...I try to scratch the powder coat with my nails and it hold still, scratch it with my bike key and it start to peel bit by bit, well, even anodize on a MacBook will scratched if you run another metal on top of it so yeah, durability is good. The red fire hydrant on the side road is a good example of powder coat on metal.
Seems like why peeps on mechkey prefer anodize is because it still "looks metal" because the material is what differentiate custom keyboard from mass-manufactured one and people want to show it off via pictures...
So to sum up, both powder coat and hard anodized coloring are quite durable with powder coat potentially be even more scratch resistant.
But powder coat looks plastic (unless the paint is a metallic color itself), and anodizing looks naturally metallic.
Post by: PollandAkuma on Tue, 06 December 2016, 08:45:53
Sent from my iPhone using Tapatalk
Post by: jebbra on Wed, 07 December 2016, 02:40:01
So to sum up, both powder coat and hard anodized coloring are quite durable with powder coat potentially be even more scratch resistant.
But powder coat looks plastic (unless the paint is a metallic color itself), and anodizing looks naturally metallic.
In general it is correct. But in powder coat we have choice of textures too, like orange skin texture.
(http://hecklerdesign.com/media/2014-0827-Heckler-Design-061-F-600x400.jpg)
I think powder coat would look nice in pastels while normal colours would look great being hard-anodised. Whichever it is, will there be an option to put feets in so the board can be tilted?
Sent from my iPhone using Tapatalk
Yep, if the new anodize vendor could give excellent result, I will still offer powder coat option in pastel. I keep debating wether the extra hole necesarry for cone feets since Planck is quite small and I never find people need to tilt it so I'll say it won't support tilting. I know it won't hurt to add 2 extra holes but as a designer I believe a beautiful product have to be look beautiful in literally every angle, even inside. And a pair of unused hole will hurt that feel :-[
PS I don't have the cone feet too so I didn't want to only 'guess' the dimension and looks with them on.
Post by: Malenky on Wed, 07 December 2016, 04:42:35
Post by: PollandAkuma on Wed, 07 December 2016, 06:00:08
Hmm I actually think this case could be the only reason to buy a planck. That case A is great, loving the Apple inspired design.
Haha, exactly my thoughts! I really don't like the normal Planck case, but these are good enough to compete with the Minivan. Especially since I want a small brick-like board! I wonder if getting this case defeats the purpose of getting a 40%... But I'd love a solid little thing.
Yep, if the new anodize vendor could give excellent result, I will still offer powder coat option in pastel. I keep debating wether the extra hole necesarry for cone feets since Planck is quite small and I never find people need to tilt it so I'll say it won't support tilting. I know it won't hurt to add 2 extra holes but as a designer I believe a beautiful product have to be look beautiful in literally every angle, even inside. And a pair of unused hole will hurt that feel :-[
PS I don't have the cone feet too so I didn't want to only 'guess' the dimension and looks with them on.
Yeah, probably best not to put those holes is no one seems to want them. I can live with it, I'd just get DSA or smt haha
Post by: menuhin on Wed, 07 December 2016, 06:16:12
My idea would be an aluminum case in teal blue with its edge showing when viewed on top, will match well with blue or cyan or other CMY color. So case B is all right (but OLKB has 3 plates offers, fit of the Alps and MX switches has yet to be tested in version 1 of the supplementary plate for case B) so I can also use my 40% keyboard sleeve interchangeably.
With an equal price tag of the milled case, this IC is keeping my attention.
Post by: PollandAkuma on Thu, 08 December 2016, 04:46:47
Post by: slot demon on Thu, 08 December 2016, 07:51:25
Post by: ipreferpie on Tue, 13 December 2016, 04:11:37
Post by: ishtob on Tue, 13 December 2016, 07:22:57
i can send you a spare cone feet set I got if you want to test it out, send me a pm
PS I don't have the cone feet too so I didn't want to only 'guess' the dimension and looks with them on.
Post by: [esc] on Tue, 13 December 2016, 08:41:51
Post by: donjoan666 on Tue, 13 December 2016, 19:02:43
Post by: jebbra on Wed, 14 December 2016, 04:20:13
No need to worry, case A will be produced but later and with some tweaks to support the current OLKB Planck plate. For now we will go with Case B.
Expect to see the sample of anodize and powder coat in the next week :thumb:
i can send you a spare cone feet set I got if you want to test it out, send me a pm
PS I don't have the cone feet too so I didn't want to only 'guess' the dimension and looks with them on.
Seems like we are too far since I'm in Indonesia ;D and I already fixed it that these case won't use cone feet because Planck is short enough on lines so it don't need one. Meanwhile, the third case will be for Preonic and will be angled by design :p
Post by: menuhin on Wed, 14 December 2016, 12:53:21
... Meanwhile, the third case will be for Preonic ...
:p Great!
I've been searching if there's a milled case for Preonic for a while.
Please also create a nice plate for it that fits both MX and Alps switches - like Jack's default plates for Planck.
Post by: PollandAkuma on Thu, 15 December 2016, 03:03:29
I'm praying for case A to be good, glad I have time to gather my funds for it <3
Post by: jebbra on Wed, 28 December 2016, 07:20:39
Fresh powder coat sample chips (the same material with the case)
[attachimg=1]
... Meanwhile, the third case will be for Preonic ...
:p Great!
I've been searching if there's a milled case for Preonic for a while.
Please also create a nice plate for it that fits both MX and Alps switches - like Jack's default plates for Planck.
But still don't have an ETA hehe. Hopefully this R&D about materials and vendors are only in the beginning so for the next cases everything will be smoother.
You're in Indonesia? Great! I'm in Singapore so less shipping for me HOORAY
I'm praying for case A to be good, glad I have time to gather my funds for it <3
Yow fellow SEA! Shipping to SG will surely cheaper, only domestic shipping can beat it :thumb:
Post by: Danilo_dk on Wed, 28 December 2016, 08:03:46
In either case, I'm really looking forward to the groupbuy for these cases. After I get my PCB this will be the final part of my second Planck build. I keep checking this thread every once in a while to check whether there is any progress. But I'm patient. So take as long as you need.
Post by: jebbra on Wed, 28 December 2016, 10:19:46
Those powder coat samples look a bit leathery. Especially the texture on that blue one that looks all shiny. But I'm sure that is also due in part because of the lighting. The black one (or is that dark grey?) looks really matte in comparison, though.
In either case, I'm really looking forward to the groupbuy for these cases. After I get my PCB this will be the final part of my second Planck build. I keep checking this thread every once in a while to check whether there is any progress. But I'm patient. So take as long as you need.
Yeah the green and blue at the middle have orange skin texture (like on those IBM Model M), the black is matte, the rest is glossy. So far the orange texture is what pique my interest the most followed by the matte. Will sleep on these tho.
I already sent my sandblasted plate to the anodize vendor and he already received but because of year-end, my order is backordered :\
Post by: neon_tom on Wed, 28 December 2016, 10:50:19
Those powder coat samples look a bit leathery. Especially the texture on that blue one that looks all shiny. But I'm sure that is also due in part because of the lighting. The black one (or is that dark grey?) looks really matte in comparison, though.
In either case, I'm really looking forward to the groupbuy for these cases. After I get my PCB this will be the final part of my second Planck build. I keep checking this thread every once in a while to check whether there is any progress. But I'm patient. So take as long as you need.
Yeah the green and blue at the middle have orange skin texture (like on those IBM Model M), the black is matte, the rest is glossy. So far the orange texture is what pique my interest the most followed by the matte. Will sleep on these tho.
I already sent my sandblasted plate to the anodize vendor and he already received but because of year-end, my order is backordered :\
That Model M texture looks amazing!
Post by: PollandAkuma on Wed, 28 December 2016, 13:07:08
Long time no update, sorry!
Fresh powder coat sample chips (the same material with the case)
(Attachment Link)
I prefer a matte powder coat :O not so shiny would be nice... only the midnight blue looks appealing right now :P
Post by: Danilo_dk on Wed, 28 December 2016, 13:47:39
Post by: aznreaper on Wed, 28 December 2016, 14:01:51
Post by: Danilo_dk on Wed, 11 January 2017, 09:09:16
Are there any rough estimates on how much longer it is going to take until the groupbuy? Or for how long the groupbuy will run for?
Post by: muten-roshi on Thu, 12 January 2017, 09:17:39
I think the smaller case looks better, but both are very nice.
Post by: jebbra on Thu, 19 January 2017, 02:54:49
Ok here we go:
1. Case B will be officially named Bullet Case while Case A may take Anvil Case as the name
2. Here's the Bullet Case with white semi-gloss powder coat over it.
[attachimg=3]
[attachimg=4]
[attachimg=1]
[attachimg=2]
TBH it still bother me that the paint is a bit clotted on every edge, may need to revise the design a bit to fix this.
3. The anodize vendor is damn long to respond anything I enquire. And I'm not happy with that attitude so will search for another, sorry.
4. The plate will be new universal design which accomodate MIT, Grid, and even 1.25u bottom row. The material will be SS 403.
[attachimg=5]
I think that's it for now. Sorry for the slow progress :-[
Post by: muten-roshi on Thu, 19 January 2017, 03:53:40
Hey and don't rush this. I am low on money anyway :)
Post by: hansichen on Thu, 19 January 2017, 04:55:54
I am low on money anyway :)
We all are right how :-[
The case looks really good so far, I'd agree that the usb port could have some improvement. Maybe just close it a bit more and post a picture from usb connecter side how it looks right now when it is in standing on the ground. I really like the support of handwired boards :thumb:
Post by: neon_tom on Thu, 19 January 2017, 07:20:51
Post by: hervuli on Thu, 19 January 2017, 10:08:36
That white powder coat looks much nicer than I anticipated it would. I'll definitely pick one of these up at this rate.
+1. Would love to see more white powder coat aluminum board options out there in general.
Post by: PollandAkuma on Thu, 19 January 2017, 14:00:53
Post by: UsualSuspectXXX on Thu, 19 January 2017, 14:14:06
So, to clarify this: I can just drop my existing Planck like it is (see picture) into that case without removing any parts?Show Image(http://uploads.tapatalk-cdn.com/20161122/e47069f2cb6fa8eab48633d80bd05a7b.jpg)
Also: can you update the image links on post #1 — maybe a Tapatalk issue, but I can only see one image.
Pretty sure you'll at least have to remove the bottom part of your case and you'll drop in everything that is attached to the plate.
Post by: muten-roshi on Thu, 19 January 2017, 15:01:44
Since the Planck will drop soon, I'll get a couple of pcb and plates, and if I like the layout I'll get Case A when it happens. I love this case sooooo much
Any idea how soon? :rolleyes:
Post by: PollandAkuma on Thu, 19 January 2017, 15:39:27
Since the Planck will drop soon, I'll get a couple of pcb and plates, and if I like the layout I'll get Case A when it happens. I love this case sooooo much
Any idea how soon? :rolleyes:
Before the end of this month, I suppose
Post by: muten-roshi on Thu, 19 January 2017, 16:01:45
Great I already don't have moneySince the Planck will drop soon, I'll get a couple of pcb and plates, and if I like the layout I'll get Case A when it happens. I love this case sooooo much
Any idea how soon? :rolleyes:
Before the end of this month, I suppose
Gesendet von meinem E5823 mit Tapatalk
Post by: PollandAkuma on Thu, 19 January 2017, 16:25:29
Great I already don't have money
me too thanks
Post by: stoic-lemon on Thu, 19 January 2017, 17:14:06
Edit: Mobile keyboard led to mangled English.
Post by: muten-roshi on Thu, 19 January 2017, 17:45:11
If pick up a Planck due to Case A. Really hope this turns out good.I want one anyway
Gesendet von meinem E5823 mit Tapatalk
Post by: jebbra on Fri, 20 January 2017, 06:55:30
I prefer do this slowly and try every option I have here. So don't worry. Will do the GB on times around payday too :p
Post by: jebbra on Sat, 21 January 2017, 00:59:46
[attachimg=1]
[attachimg=2]
Post by: hansichen on Sat, 21 January 2017, 06:34:57
Post by: neon_tom on Sat, 21 January 2017, 08:20:52
Here's the USB port in use in usual view angle. Looks good right?
(Attachment Link)
(Attachment Link)
Gorgeous!
Post by: MNICI on Thu, 26 January 2017, 14:10:58
White powdercoat looks pretty nice, but a bit plastic-y in my opinion. I would prefer clear/silver anodization myself, but as you said that depends on vendor availibility.
Would it be possible to get raw case B with a little discount? I may find some local place to anodise it on my own...
About USB hole - why not make it smaller like this? This way PCB wont be as visible.
Post by: jebbra on Thu, 26 January 2017, 21:16:21
Created a GH account just to post here ;)
White powdercoat looks pretty nice, but a bit plastic-y in my opinion. I would prefer clear/silver anodization myself, but as you said that depends on vendor availibility.
Would it be possible to get raw case B with a little discount? I may find some local place to anodise it on my own...
About USB hole - why not make it smaller like this? This way PCB wont be as visible.
The purpose of having wide usb post is to support hand wiring. Because when handwiring, the micro controller used is placed on the bottom of the case so the usb port is a bit lower. But don't worry, the hollow part won't be visible IRL (look at the photo I take).
I can do raw too since the MOQ for powder coat is quite low, this way I feel more fair for people who want to anodize or treat it whatever they want. One question tho: my CNC vendor said it is better to keep the case oily if you want to coat it later, is this true?
Post by: breckstar on Thu, 26 January 2017, 22:07:45
Post by: shensmobile on Thu, 26 January 2017, 22:37:31
As for keeping the case oily, if it were steel I would say that helps for rust prevention, but for an aluminum case, I'm not quite sure. I'm an electrical engineer, not a mechanical so I can't help too much here! Sorry!
Post by: slot demon on Fri, 27 January 2017, 02:14:57
Post by: jebbra on Fri, 27 January 2017, 04:09:27
Any hope of getting preonic version?
Yep, after these 2 I plan on making a hipro Preonic case, along with standard plate.
Just created an account to say that I am absolutely in for Case A. That's pretty much the thing holding me back from grabbing a Planck, I love high profile cases and that one fits the bill. If you can offer it annodized, or raw I would be elated!
As for keeping the case oily, if it were steel I would say that helps for rust prevention, but for an aluminum case, I'm not quite sure. I'm an electrical engineer, not a mechanical so I can't help too much here! Sorry!
That's nice of you creating GH account just to say it, thank you :) If there's no capable anodize vendor I will offer them raw too, with price reduction. Just confirmed it that it still necessary for aluminum too, as it will prevent oxidation (black specks) on exposed aluminum.
Any update? Case A is a dream, I like also the plain silver look.
I will go to the vendor tomorrow. Sorry for the long process, I can only do the visit on Saturday because my work :(
Post by: breckstar on Sun, 29 January 2017, 19:17:14
Any hope of getting preonic version?
Yep, after these 2 I plan on making a hipro Preonic case, along with standard plate.
Sweeeeeeeeeet. Looking forward to it :)
Post by: shensmobile on Mon, 30 January 2017, 12:07:28
That's nice of you creating GH account just to say it, thank you :) If there's no capable anodize vendor I will offer them raw too, with price reduction. Just confirmed it that it still necessary for aluminum too, as it will prevent oxidation (black specks) on exposed aluminum.
Hey you're doing fantastic work, you deserve the props/thanks/orders! The fact that you're making Case A compatible with the Planck plate is huge news and awesome design! I'm eagerly following this thread :)
Post by: piercejenkins on Mon, 06 February 2017, 11:41:49
Post by: jebbra on Mon, 06 February 2017, 22:03:35
That's nice of you creating GH account just to say it, thank you :) If there's no capable anodize vendor I will offer them raw too, with price reduction. Just confirmed it that it still necessary for aluminum too, as it will prevent oxidation (black specks) on exposed aluminum.
Hey you're doing fantastic work, you deserve the props/thanks/orders! The fact that you're making Case A compatible with the Planck plate is huge news and awesome design! I'm eagerly following this thread :)
When will case A be available for order?
Anvil Case must wait longer, I will release Bullet Case 1st and gather feedback from it then proceed to open the Anvil. But the IC won't be as long as this one because when the Bullet release it means I already acquire the right vendor (actually the only vendor missing is anodizing).
Post by: Juice_box on Tue, 07 February 2017, 14:11:22
Post by: stoic-lemon on Wed, 08 February 2017, 06:39:26
Post by: jebbra on Wed, 08 February 2017, 10:17:39
Post by: jal on Wed, 08 February 2017, 10:56:57
So to sum up, both powder coat and hard anodized coloring are quite durable with powder coat potentially be even more scratch resistant.
But powder coat looks plastic (unless the paint is a metallic color itself), and anodizing looks naturally metallic.
It does look plastic, because it is plastic. But powder coat comes in a pretty wide range of options. There are translucent options, metal-flake options, it can be shiny or matte (usually, shiny is done with a clear top-coat), and there is a huge range of colors (but most shops only have a small subset on hand).
In case you're interested in more detail, here's detail on DIY:
http://www.powdercoatguide.com/
And one shop's colors:
https://www.prismaticpowders.com/powder-coating-colors/
For info on anodizing, I recommend starting with the Wikipedia page: https://en.wikipedia.org/wiki/Anodizing .
Disclaimer: I have powder-coated things, but not much because I hate doing it, so I'm no expert. I hate wearing a respirator and waving 15KV around while puffing flammable powder at metal (==spark risk) tends to make me nervous. And I've never tried to anodize anything. Something about heating an acid bath and then running current through it makes me think I should just play in an alligator pit instead.
Post by: jebbra on Thu, 09 February 2017, 05:57:35
[attachimg=1]
Not yet getting my hands on it, but the pic looks promising :-*
I will pick it up on Saturday.
Post by: stoic-lemon on Thu, 09 February 2017, 06:29:14
Post by: Danilo_dk on Fri, 10 February 2017, 12:01:37
Post by: menuhin on Fri, 10 February 2017, 13:26:52
I have to remain patient though. ^-^
Post by: PollandAkuma on Fri, 10 February 2017, 18:23:43
Okay got a potato pic from the gramps at anodizing vendor >:DNice to see you got some good relations going! That's part of the fun :D
(Attachment Link)
Not yet getting my hands on it, but the pic looks promising :-*
I will pick it up on Saturday.
Post by: BaconEggandCheeseBagel on Fri, 10 February 2017, 18:41:36
Post by: Danilo_dk on Sat, 11 February 2017, 05:08:46
Post by: gadzkun on Sat, 11 February 2017, 08:08:42
Post by: jebbra on Sat, 11 February 2017, 22:49:53
case and anodizing was good already see and touch it, this is the first time i reallly want an ortholinear board. :thumb:
Cases spotted in the wild. Both looking great.Show Image(http://i.imgur.com/RRVuB7z.jpg)
Thx mates!
Okay I already have my hands on it and I really love it! But he said there is one more superior anodize method and I want to try it first. And will sample some colors to anodize for final GB offer.
Post by: robotmaxtron on Wed, 22 February 2017, 00:57:32
Post by: shinz0 on Wed, 22 February 2017, 19:15:53
Post by: fatpolomanjr on Thu, 23 February 2017, 00:07:29
Post by: jebbra on Thu, 23 February 2017, 00:57:11
Have you considered doing a split version after releasing the standard planck case?
There's ton of keyboard design in my head right now. Including split planck. and I heard OLKB will release split version too in not so distant future. I'll wait for that for now.
Post by: jebbra on Thu, 23 February 2017, 00:59:50
Post by: simonyunhe on Thu, 23 February 2017, 01:09:33
Post by: jebbra on Thu, 23 February 2017, 01:28:20
[attachimg=1]
[attachimg=2]
[attachimg=3]
Only little blemish appeared on the edge, that's the rigging problem I need to take care of. Already drop some plate in same material and finish to make color samples :thumb:
Post by: ricyuyc on Thu, 23 February 2017, 04:01:13
Post by: sems on Thu, 23 February 2017, 08:22:30
Anodize looks nice!
(Attachment Link)
(Attachment Link)
(Attachment Link)
Only little blemish appeared on the edge, that's the rigging problem I need to take care of. Already drop some plate in same material and finish to make color samples :thumb:
Whoa! Color me impressed!
Post by: fatpolomanjr on Thu, 23 February 2017, 14:56:46
There's ton of keyboard design in my head right now. Including split planck. and I heard OLKB will release split version too in not so distant future. I'll wait for that for now.
Nice! I really like this aluminum design, plus who wouldn't want two blocks of metal for self defense? Weapon of choice IMO.
Post by: aznreaper on Sat, 25 February 2017, 20:34:47
Post by: jchan94 on Sat, 25 February 2017, 21:40:55
Post by: mr scooty on Tue, 07 March 2017, 22:02:22
Post by: stillzman on Wed, 08 March 2017, 21:45:33
Post by: ectoplasmatic on Tue, 14 March 2017, 04:09:24
Post by: Kafka on Tue, 14 March 2017, 09:58:08
Post by: Zammux on Tue, 14 March 2017, 12:18:00
Post by: ibakey on Wed, 22 March 2017, 05:48:32
Post by: neralo on Wed, 22 March 2017, 09:10:20
Post by: Theconejo on Fri, 24 March 2017, 18:05:49
Watching this for case b
Post by: futurecrime on Sat, 25 March 2017, 21:24:20
Post by: mniels on Sat, 25 March 2017, 21:27:36
Post by: layornos on Tue, 28 March 2017, 15:59:00
Post by: zeta on Tue, 28 March 2017, 21:08:33
Post by: oluigenuma on Thu, 30 March 2017, 07:56:38
Post by: JDT79 on Thu, 30 March 2017, 08:42:11
Post by: hansichen on Wed, 19 April 2017, 08:11:03
Any news about this, have you survived your wedding or did she canceled all your keyboard projects? :p
Just kidding :))
Post by: jebbra on Wed, 19 April 2017, 10:07:44
A small silent bump ;D
Any news about this, have you survived your wedding or did she canceled all your keyboard projects? :p
Just kidding :))
Okay, update: the wedding went well (yay!) but my wife was sad because no KK Meow Calico for her (need to pray more to RNGsus after this) and I'm just arriving at my futon in Tokyo after having a Coldplay concert. Scheduled to take flight tomorrow and a meet with the workshop at Saturday.
Simpler version: I'm still on honeymoon and will post sample color on Monday :thumb:
Post by: Theconejo on Wed, 19 April 2017, 10:15:41
A small silent bump ;D
Any news about this, have you survived your wedding or did she canceled all your keyboard projects? :p
Just kidding :))
Okay, update: the wedding went well (yay!) but my wife was sad because no KK Meow Calico for her (need to pray more to RNGsus after this) and I'm just arriving at my futon in Tokyo after having a Coldplay concert. Scheduled to take flight tomorrow and a meet with the workshop at Saturday.
Simpler version: I'm still on honeymoon and will post sample color on Monday :thumb:
Wow, congrats on the wedding! Posting updates while on honeymoon = dedication!
Post by: hansichen on Wed, 19 April 2017, 14:49:25
A small silent bump ;D
Any news about this, have you survived your wedding or did she canceled all your keyboard projects? :p
Just kidding :))
Okay, update: the wedding went well (yay!) but my wife was sad because no KK Meow Calico for her (need to pray more to RNGsus after this) and I'm just arriving at my futon in Tokyo after having a Coldplay concert. Scheduled to take flight tomorrow and a meet with the workshop at Saturday.
Simpler version: I'm still on honeymoon and will post sample color on Monday :thumb:
Sounds good, I appreciate your update :thumb: Planck really needs a nice high profile case :D
Post by: ibakey on Wed, 19 April 2017, 23:48:22
Post by: joelfong on Thu, 27 April 2017, 12:34:03
Post by: donut_sauce on Thu, 27 April 2017, 12:43:20
Post by: GreyAmbience on Fri, 28 April 2017, 16:54:33
Post by: Wren on Tue, 02 May 2017, 09:51:55
Post by: Ragequit on Sun, 14 May 2017, 20:10:49
I hope this project arrives to maturity and delivers
Post by: smt on Sun, 14 May 2017, 22:32:39
Post by: jebbra on Tue, 16 May 2017, 01:40:11
But good news is, there's no MOQ for colors so even only 1 person want pink it will still be made :thumb:
GB is scheduled starting this weekend, opened for 1 week, then 4 days for invoice payment.
[attachimg=1]
Post by: futurecrime on Tue, 16 May 2017, 02:14:08
Sorry for the long wait, here is the sample color. Yes they're not as bright as the usual anodize, a reason is because I use sandblast instead of beadblast (my vendor said the more matte the surface, the less vibrant the color), the other reason is maybe the coloring material my vendor use is rather different. Personally I like them this way, more earthy tone. And my vendor have purple and green too but I ran out of material.
But good news is, there's no MOQ for colors so even only 1 person want pink it will still be made :thumb:
GB is scheduled starting this weekend, opened for 1 week, then 4 days for invoice payment.
(Attachment Link)
I really like the slightly muted colours too. Got a few questions: Is that white I see there? Is this first GB still gonna be for case 2? And do you have a price yet?
Post by: neralo on Tue, 16 May 2017, 02:33:05
Sorry for the long wait, here is the sample color. Yes they're not as bright as the usual anodize, a reason is because I use sandblast instead of beadblast (my vendor said the more matte the surface, the less vibrant the color), the other reason is maybe the coloring material my vendor use is rather different. Personally I like them this way, more earthy tone. And my vendor have purple and green too but I ran out of material.
But good news is, there's no MOQ for colors so even only 1 person want pink it will still be made :thumb:
GB is scheduled starting this weekend, opened for 1 week, then 4 days for invoice payment.
(Attachment Link)
Looking forward to the end of Case Bs gb so I can get on Case A. Glad to see this coming along really nicely, and those colours are really wonderful.
Post by: jebbra on Tue, 16 May 2017, 03:47:00
I really like the slightly muted colours too. Got a few questions: Is that white I see there? Is this first GB still gonna be for case 2? And do you have a price yet?
It is clear, the material color. It supposedly silver but in reality it is more white than the silver of MacBook. Price will start at $100, this include anodized alu case, choice of SS/brass plate, screws, and rubber feet, but exclude postage and pp fee for 20 orders and will have some drop point along the way. I still work on this, especially the packaging cost.
Looking forward to the end of Case Bs gb so I can get on Case A. Glad to see this coming along really nicely, and those colours are really wonderful.
Appreciate the wait man. Anvil will be overhauled so it can have OLKB plates snugged into it :thumb:
Post by: jebbra on Tue, 16 May 2017, 03:52:47
Post by: futurecrime on Tue, 16 May 2017, 04:05:20
I really like the slightly muted colours too. Got a few questions: Is that white I see there? Is this first GB still gonna be for case 2? And do you have a price yet?
It is clear, the material color. It supposedly silver but in reality it is more white than the silver of MacBook. Price will start at $100, this include anodized alu case, choice of SS/brass plate, screws, and rubber feet, but exclude postage and pp fee for 20 orders and will have some drop point along the way. I still work on this, especially the packaging cost.Looking forward to the end of Case Bs gb so I can get on Case A. Glad to see this coming along really nicely, and those colours are really wonderful.
Appreciate the wait man. Anvil will be overhauled so it can have OLKB plates snugged into it :thumb:
I love both cases but I think I'm gonna have to just wait for Case A as well (and Mondrian!). April and May have been quite ridiculous for keyboard spending. Good luck with the GB anyway, the case looks gorgeous.
EDIT: A for B.
Post by: h3xadat on Tue, 16 May 2017, 05:09:13
Btw, since Bullet case use a different plate than OLKB one, do any of you want the PCB too? If yes, I will arrange it with Jack so the buyer of this case will have a price cut on OLKB Planck PCB. Assuming there are a fair number of people want the PCB tho ;D
Count me in for the Bullet case and the PCB.
Post by: breckstar on Tue, 16 May 2017, 15:29:18
Post by: Ragequit on Tue, 16 May 2017, 19:02:18
Count me in for the Bullet case and the PCB.
Same
Post by: teeseeuu on Wed, 17 May 2017, 07:09:13
Post by: arsenics on Wed, 17 May 2017, 07:43:01
Post by: r5d on Wed, 17 May 2017, 08:54:14
Post by: KetchyKech on Wed, 17 May 2017, 09:23:30
Post by: roostrc0gburn on Wed, 17 May 2017, 11:26:20
can you please clarify. thanks!
Post by: Korseir on Wed, 17 May 2017, 14:49:48
Post by: PotatoTM on Wed, 17 May 2017, 15:15:54
Post by: jebbra on Wed, 17 May 2017, 22:59:57
sorry, i was confused by the email - the group buy starts this weekend (May 20?) and goes for 2 weeks (June 3?)
can you please clarify. thanks!
Yes, it will go live around that time.
I must be blind but where exactly do I fill in the form to enter the GB?
No sir, your eyes are perfectly fine. The form will be live this weekend ;)
Colors are sick. Those gold/champagne and red look like excellent matches for Jukebox. Here's to hoping preonic R2 still is on the books.
I still intended to release Preonic case, thank you for the interest!
Post by: roostrc0gburn on Wed, 17 May 2017, 23:16:44
Post by: Biggestmac on Thu, 18 May 2017, 02:58:04
Post by: jebbra on Thu, 18 May 2017, 04:05:40
"GB will open this weekend, May 14th 2017 and opened for 2 weeks." was wrong, it should be May 21st, not 14th. My bad :-X
Post by: Biggestmac on Thu, 18 May 2017, 19:30:43
Post by: Biggestmac on Sun, 21 May 2017, 15:42:22
Post by: jebbra on Mon, 22 May 2017, 07:20:53
Will this GB still be starting today?
Yes. The GB thread is waiting appoval now >> https://geekhack.org/index.php?topic=89677.0
Post by: teeseeuu on Mon, 22 May 2017, 08:30:16
Post by: ChitownM2 on Mon, 22 May 2017, 12:34:00
You have a direct link to the form?
Haven't read all of the forum rules, but I would assume that they prohibit linking directly to the GB order form in an IC thread. That is kind of the whole point in having the mods vet the GB thread in the first place.
Post by: teeseeuu on Mon, 22 May 2017, 12:35:29
You have a direct link to the form?Yeah, most likely. Thanks for the clarification
Haven't read all of the forum rules, but I would assume that they prohibit linking directly to the GB order form in an IC thread. That is kind of the whole point in having the mods vet the GB thread in the first place.
Post by: Arcsxum on Mon, 22 May 2017, 13:07:59
Post by: jebbra on Tue, 23 May 2017, 03:49:47
You have a direct link to the form?Yeah, most likely. Thanks for the clarification
Haven't read all of the forum rules, but I would assume that they prohibit linking directly to the GB order form in an IC thread. That is kind of the whole point in having the mods vet the GB thread in the first place.
It is open now! >> https://geekhack.org/index.php?topic=89677.0
This reminds me a bit of Rama's designs.
Yep we both inspired by the magnificent Apple M0110A!
Post by: jebbra on Tue, 23 May 2017, 03:51:13
GroupBuy thread is open! >> https://geekhack.org/index.php?topic=89677.0 <<
Post by: MrBreakfst on Mon, 05 June 2017, 19:30:53
I've had a change of heart... Can I cancel my order so that I can wait for the anvil?
Post by: jebbra on Tue, 06 June 2017, 08:07:41
ohhhh dear
I've had a change of heart... Can I cancel my order so that I can wait for the anvil?
Damn I just see your post. Just don't pay the invoice then, it's okay :)
Post by: wtzll on Tue, 20 June 2017, 08:47:36
Post by: dirksoccer on Thu, 22 June 2017, 10:38:11
Post by: Ragequit on Thu, 22 June 2017, 14:55:57
Post by: ibakey on Thu, 29 June 2017, 00:43:48
Sent from my iPhone using Tapatalk
Post by: Gavus on Sun, 02 July 2017, 08:27:24
Sent from my HTC One A9 using Tapatalk
Post by: jebbra on Mon, 03 July 2017, 00:23:46
Is there a mailing list for the anvil group buy, or should we just watch this thread?
Yes you can input it here https://goo.gl/forms/shPLUsCtqkxoOwyD2
Will it be possible to insert an acrylic plate between the parts of the anvil case? Maybe to allow RGB underglow or just to make the case higher.
My sketch for Anvil have the line hidden so seems like we can't add acrylic layer for glow.
Post by: achilles_other_heel on Tue, 29 August 2017, 22:21:47
Post by: jebbra on Sat, 02 September 2017, 05:07:31
jebbra, anyway we could see a render of the Anvil with blocks in the left and right corners? Like the original M0110? Just curious what it'd look like.
Sadly I don't have it on ortholinear mode.
But I have the prototype for the standard staggered 60 one :p
[attachimg=1]
Here's the snippet from local CNN reportage:
[attachimg=2]
[attachimg=3]
Post by: wtzll on Sat, 02 September 2017, 10:01:01
jebbra, anyway we could see a render of the Anvil with blocks in the left and right corners? Like the original M0110? Just curious what it'd look like.
Sadly I don't have it on ortholinear mode.
But I have the prototype for the standard staggered 60 one :p
(Attachment Link)
Here's the snippet from local CNN reportage:
(Attachment Link)
(Attachment Link)
Nice! So you famous now huh :)
Post by: achilles_other_heel on Thu, 14 September 2017, 23:24:51
jebbra, anyway we could see a render of the Anvil with blocks in the left and right corners? Like the original M0110? Just curious what it'd look like.
Sadly I don't have it on ortholinear mode.
But I have the prototype for the standard staggered 60 one :p
(Attachment Link)
Here's the snippet from local CNN reportage:
(Attachment Link)
(Attachment Link)
Thanks! Those look good :) seriously can't wait for the anvil!
Post by: RealLaugh on Fri, 15 September 2017, 00:21:44
jebbra, anyway we could see a render of the Anvil with blocks in the left and right corners? Like the original M0110? Just curious what it'd look like.
Sadly I don't have it on ortholinear mode.
But I have the prototype for the standard staggered 60 one :p
(Attachment Link)
Here's the snippet from local CNN reportage:
(Attachment Link)
(Attachment Link)
Do you have an IC thread for that case?
Post by: jebbra on Fri, 15 September 2017, 00:40:54
jebbra, anyway we could see a render of the Anvil with blocks in the left and right corners? Like the original M0110? Just curious what it'd look like.
Sadly I don't have it on ortholinear mode.
But I have the prototype for the standard staggered 60 one :p
(Attachment Link)
Here's the snippet from local CNN reportage:
(Attachment Link)
(Attachment Link)
Do you have an IC thread for that case?
Not yet, planned on releasing the render soon, along with DSA Fuku IC.
Post by: stillzman on Wed, 20 December 2017, 16:08:15
Post by: achilles_other_heel on Thu, 03 May 2018, 10:40:33
Post by: garbo on Thu, 03 May 2018, 13:15:23
Not to bother Jebbra too much, but I must say, I find myself lying awake at night thinking about the anvil case. Can't wait for it to drop.
I know, right?
Post by: bs95 on Tue, 26 June 2018, 03:38:30
Post by: Rumblehotep on Tue, 10 July 2018, 18:48:04