Looks good overall! I would recommend two things to make casting easier. I would make the mouth solid, and carve the teeth, so there isn't an actual gap in the mouth (if that makes sense, just so that there's no nooks or crannies when you're casting that will make the mold all wonky). I would also angle the leaves up a bit, so that they aren't also parallel to the top of the mold. It would make it easier to pull out of the mold, even if you only angle it 20 degrees or so.
Great progress so far though, can't wait to see what else you'll make :thumb:
How do you actually make those?@iLLucionist currently I'm just sculpting these out of Super Sculpey http://www.ebay.com/itm/251644946799?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT (http://www.ebay.com/itm/251644946799?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT). Next step is to actually bake them, so they harden and from there I can start the casting process.
If that goomba is small enough to not hit the caps around it that's looking great, and piranha plant v2 looks easier to cast and more comfortable to press - definite progress :thumb:@suicidal_orange So far I think it is. I actually don't have a mech at home, just in the office. I'll have to cart the lil goomba in tomorrow and see.π
How do you actually make those?@iLLucionist currently I'm just sculpting these out of Super Sculpey http://www.ebay.com/itm/251644946799?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT (http://www.ebay.com/itm/251644946799?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT). Next step is to actually bake them, so they harden and from there I can start the casting process.
Boo hiss - I made this fella a lil to big. I'll have to try sanding it down now that I baked it. I may also just try and make a V2, we'll see what shapes up.Show Image(http://i.imgur.com/QXQiQC7.jpg)Show Image(http://i.imgur.com/LqChKJc.jpg)
Boo hiss - I made this fella a lil to big. I'll have to try sanding it down now that I baked it. I may also just try and make a V2, we'll see what shapes up.Show Image(http://i.imgur.com/QXQiQC7.jpg)Show Image(http://i.imgur.com/LqChKJc.jpg)
Looks nice. Can you actually push that cap down?
The goomba needs to go on a diet.
I'm going to try sanding it down tonight, and if that doesn't work out I will make another one.
Started working on Goomba V1.5Show Image(http://i.imgur.com/V3bIPf6.jpg)Show Image(http://i.imgur.com/3yOvzHI.jpg)Show Image(http://i.imgur.com/8kL5rfm.jpg)Show Image(http://i.imgur.com/BTSHNim.jpg)
Definitely a rough pass right now, hopefully I can get some more time in tomorrow and make this lil fella look better.
Nice attempts! Are you going to paint them over? Or leave them as is?@iLLucionist - just sold my planck on /r/mechmarket to fund the purchase of casting materials.
I like the one with eyebrows. Can't imagine a Goomba without 'em!@romevi the eyebrows totally make the goomba, we'll see if I get to the point where I can add them to the grey one tonight.
Looking good so far! Are you going to add pupils?
I've been working on making this cap a little smaller. Here are the updates.Show Image(http://imgur.com/U8Y7EOm.jpg)Show Image(http://imgur.com/3Zw5AT5.jpg)Show Image(http://imgur.com/TjgGAi8.jpg)
Still tracking down a taster oven that is not total trash.
UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?
I've been working on making this cap a little smaller. Here are the updates.Show Image(http://imgur.com/U8Y7EOm.jpg)Show Image(http://imgur.com/3Zw5AT5.jpg)Show Image(http://imgur.com/TjgGAi8.jpg)
Still tracking down a taster oven that is not total trash.
(http://s31.postimg.org/410c11k2f/frabz_Feed_me_seymour_feed_me_all_night_long_780.jpg) (http://postimg.org/image/410c11k2f/)
Casting supplies should be here tomorrow, just in time for all sorts of new learning.UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?
I think it looks very promising so far! It'd be interesting to see the goomba in different colourways!I'm excited to make a large bowl of rejects! Then maybe after that I'll have something worth showing :D
UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?
I think those will be used to make molds.
Was that from the super mario movie? I'm wondering if its supposed to be the piranha plant.I've been working on making this cap a little smaller. Here are the updates.Show Image(http://imgur.com/U8Y7EOm.jpg)Show Image(http://imgur.com/3Zw5AT5.jpg)Show Image(http://imgur.com/TjgGAi8.jpg)
Still tracking down a taster oven that is not total trash.
(http://s31.postimg.org/410c11k2f/frabz_Feed_me_seymour_feed_me_all_night_long_780.jpg) (http://postimg.org/image/410c11k2f/)
That's.... odd.
Casting supplies should be here tomorrow, just in time for all sorts of new learning.UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?I think it looks very promising so far! It'd be interesting to see the goomba in different colourways!I'm excited to make a large bowl of rejects! Then maybe after that I'll have something worth showing :DUpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?
I think those will be used to make molds.
Yes sir.Was that from the super mario movie? I'm wondering if its supposed to be the piranha plant.I've been working on making this cap a little smaller. Here are the updates.Show Image(http://imgur.com/U8Y7EOm.jpg)Show Image(http://imgur.com/3Zw5AT5.jpg)Show Image(http://imgur.com/TjgGAi8.jpg)
Still tracking down a taster oven that is not total trash.
(http://s31.postimg.org/410c11k2f/frabz_Feed_me_seymour_feed_me_all_night_long_780.jpg) (http://postimg.org/image/410c11k2f/)
That's.... odd.
Yes Little Shop of Horrors. Fun fact I recently saw a interview with Rick Moranis saying it took 52 puppeteers for the giant plant. Great cult movie.Casting supplies should be here tomorrow, just in time for all sorts of new learning.UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?I think it looks very promising so far! It'd be interesting to see the goomba in different colourways!I'm excited to make a large bowl of rejects! Then maybe after that I'll have something worth showing :DUpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?
I think those will be used to make molds.
Yes sir.Was that from the super mario movie? I'm wondering if its supposed to be the piranha plant.I've been working on making this cap a little smaller. Here are the updates.Show Image(http://imgur.com/U8Y7EOm.jpg)Show Image(http://imgur.com/3Zw5AT5.jpg)Show Image(http://imgur.com/TjgGAi8.jpg)
Still tracking down a taster oven that is not total trash.
(http://s31.postimg.org/410c11k2f/frabz_Feed_me_seymour_feed_me_all_night_long_780.jpg) (http://postimg.org/image/410c11k2f/)
That's.... odd.
Isn't it Little Shop of Horrors?
Loving your goombas! Keep up the progress! Would love to see finished products. :thumb:Thanks! Should have some bad castings next week.
Little sanding and finishing touches on the goomba tonight. Went for the pupils.Show Image(http://i.imgur.com/iHAWnlc.jpg)Show Image(http://i.imgur.com/ky0cNRc.jpg)
Casting supplies should be in tomorrow, so new things to start working on.
Ha ha! The pupils definitely make it better.
Little sanding and finishing touches on the goomba tonight. Went for the pupils.Show Image(http://i.imgur.com/iHAWnlc.jpg)Show Image(http://i.imgur.com/ky0cNRc.jpg)
Casting supplies should be in tomorrow, so new things to start working on.
:thumb: be prepared for massively bad things to show up for a while.
Man he keeps getting better and better! Nice updates! :thumb:
Yes Little Shop of Horrors. Fun fact I recently saw a interview with Rick Moranis saying it took 52 puppeteers for the giant plant. Great cult movie.Casting supplies should be here tomorrow, just in time for all sorts of new learning.UpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?I think it looks very promising so far! It'd be interesting to see the goomba in different colourways!I'm excited to make a large bowl of rejects! Then maybe after that I'll have something worth showing :DUpdatesShow Image(http://i.imgur.com/4rf7War.jpg)Show Image(http://i.imgur.com/LlR9Cx4.jpg)Show Image(http://i.imgur.com/RBsAWkn.jpg)Show Image(http://i.imgur.com/Xoy1vkX.jpg)
Needs some smoothing up, but overall I'm currently happy with it.
Looks really cool. Is that the final state or are you also going to paint it?
I think those will be used to make molds.
Yes sir.Was that from the super mario movie? I'm wondering if its supposed to be the piranha plant.I've been working on making this cap a little smaller. Here are the updates.Show Image(http://imgur.com/U8Y7EOm.jpg)Show Image(http://imgur.com/3Zw5AT5.jpg)Show Image(http://imgur.com/TjgGAi8.jpg)
Still tracking down a taster oven that is not total trash.
(http://s31.postimg.org/410c11k2f/frabz_Feed_me_seymour_feed_me_all_night_long_780.jpg) (http://postimg.org/image/410c11k2f/)
That's.... odd.
Isn't it Little Shop of Horrors?
I like what you have going on here. I noticed that the new goomba seems to be a completely different style when compared to the original goomba. What is that about?
I like what you have going on here. I noticed that the new goomba seems to be a completely different style when compared to the original goomba. What is that about?
I had to do some re-jiggering of the shape of the goomba. The first one was really fat, so i was able to taper it under at towards the base and that added a lot of nice shape. I also used a different super sculpey for the littler one.
Thanks for looking so closely at my work!
Thanks! I'll keep it up.I like what you have going on here. I noticed that the new goomba seems to be a completely different style when compared to the original goomba. What is that about?
I had to do some re-jiggering of the shape of the goomba. The first one was really fat, so i was able to taper it under at towards the base and that added a lot of nice shape. I also used a different super sculpey for the littler one.
Thanks for looking so closely at my work!
Haha, don't stop sculpting. :thumb:
Great work man! Love to see your progress, can't get enough Mario themed stuff :)Thanks brother! I'm very glad to hear the 'can't get enough Mario themed" line, as I may or may not have a few more ideas planned out.
Okay update time!
First off, I totally messed up the the 2nd part of the first mold. I completely forgot to grab the petroleum jelly, and make sprus. so.. yeah that was 12 hours of waiting for curing down the drain.
However I was able to remember those vital steps the next time around!Show Image(http://i.imgur.com/HCkw4bE.jpg)Show Image(http://i.imgur.com/gIJsytf.jpg)
and here is the 2nd mold next to the first one. I had to cut that one up to get the goomba out.. Also notice my excellent consistency in the mixture amounts.Show Image(http://i.imgur.com/lGaIKe7.jpg)
Spru!Show Image(http://i.imgur.com/cEs7YQu.jpg)
And now the more exciting part.Show Image(http://i.imgur.com/xJry1Tm.jpg)Show Image(http://i.imgur.com/xyrEkWY.jpg)Show Image(http://i.imgur.com/ZppsXqM.jpg)Show Image(http://i.imgur.com/PcInzmr.jpg)Show Image(http://i.imgur.com/hxXsRt3.jpg)Show Image(http://i.imgur.com/iSjdQjM.jpg)Show Image(http://i.imgur.com/ZAF6iM6.jpg)Show Image(http://i.imgur.com/MtBewCT.jpg)
Darth goomba is a little wobbly on the stem, and naturally has a few bubbles but I'm super stoked on it! I'm casting a yellow one right this moment, and I may have photos before I go to bed.
Looks great so far! MX stems are pretty hard to work with at first but definitely better than most of my first successes!
Great progress!! Awesome for a first cast. :thumb:I was very happy with it for the first cast
It almost looks like cola in one of those pictures :)You know I think you've got the right idea on it. Cola Goomba
Still having trouble with bubbles, but I'll get there I think.Show Image(http://i.imgur.com/qjmnduN.jpg)
The clear one looks like a ghost from pacmanShow Image(http://i.imgur.com/4lyIPEx.jpg)Show Image(http://i.imgur.com/GyY8vhr.jpg)Show Image(http://i.imgur.com/A66kBsU.jpg)
The row of goombas up front arent key caps. Remember when I ***ed up the first mold? Well when I mix up some resin I have more than enough to fill the working mold, and I couldn't possibly throw away the first mold, so I just pour some resin in there and see how it shapes up.
Thanks for all the support everyone, hopefully I'll have some quality keys in the not too distant future.
Looking good! Like the trans ones.Thanks man! Now if only they didn't have bubbles in them, they'd look way better.
Looking good! Like the trans ones.Thanks man! Now if only they didn't have bubbles in them, they'd look way better.
Looking good! Like the trans ones.Thanks man! Now if only they didn't have bubbles in them, they'd look way better.
Bubbles are evil. Bubbles were sent to destroy us.
Nice work. Keep it up!
Update, less bubbles but still there.Show Image(http://i.imgur.com/I7f46Ag.jpg)Show Image(http://i.imgur.com/xqy4A3L.jpg)Show Image(http://i.imgur.com/5ZnStmh.jpg)Show Image(http://i.imgur.com/MqsZj2p.jpg)Show Image(http://i.imgur.com/adfL0Y6.jpg)Show Image(http://i.imgur.com/2Pp39tM.jpg)Show Image(http://i.imgur.com/hfKJ1uF.jpg)
The little gang on my desk is growingShow Image(http://i.imgur.com/Wttasz7.jpg)Show Image(http://i.imgur.com/8bRIx7F.jpg)
And more mold troubles. The first two molds that I made turned out just fine, and now that I'm trying to build a 2 blank mold, I'm having issues with the stems. 3rd try was not the charm :( Time to pickup some pipettes if I can find them locally.Show Image(http://i.imgur.com/yF5vqG1.jpg)Show Image(http://i.imgur.com/D3adX8f.jpg)
Really thought I had it last night, used a small pick to try and get everything out of the stem.. Maybe 4th try.
Im certainly no pro, but for my stems, I found trying to even carefully inject it with a syringe still caused bubbles.Thanks for the tip! I'm ordering the pipets today, but I may try that paper clip version tonight.
The one thing that has been 100% successful for me is just dabbing a thin paperclip in the silicone, and wiping the silicone in all four sides of the stem, then progressively dabbing more and more goop until its fill up even with the top of the stem. then high pour the rest in.
Im going to make my first buckling spring mold tonight!
My officemate has a few leds in their keyboard. Glowing goombaShow Image(http://i.imgur.com/F0ZtNgw.jpg)Show Image(http://i.imgur.com/iMCjLMX.jpg)
Very good job, and a great officemate to have who has a mech keyboard!Luckily she's super cool, and that keyboard was also my first mech. I traded it to her for a breakfast burrito and an led light table from ebay.
Hell yea, the stems look way better!
Honestly, doing that, Ive made caps that fit better than all the artisans I own. (which is hardly any)
Im starting to run low on the oomoo because I was using too much early on.
Im going to order some in the next month or so and get back into making stuff other than blanks.
Nice job! :thumb:
really good work there. hope to see more updatesI'll have some minor ones in a bit
looking good. hopefully mine will have smoother processI wish you the best of luck and hope that you also have a smoother process. This is rough going!
really good work there. hope to see more updatesI'll have some minor ones in a bitlooking good. hopefully mine will have smoother processI wish you the best of luck and hope that you also have a smoother process. This is rough going!
Very interesting. Noted for my own endeavors in the future.
I like that short teal one in the first pictures. I don't know why, but I've come to prefer shorter artisan caps lately.
Nice colors! I'm looking forward to more developmentsThank you! I've been mixing in some white and then a little of another color in order to make an opaque color from the tints that I have. Next time I make an order, probably today or tomorrow, if I can afford it I'll pick up some opaque colors.
Very interesting. Noted for my own endeavors in the future.Funny story about those, they aren't actually keycaps. The short ones are, as I have taken to calling them anyway, desk warts. If you read further up in this thread you'll find that I royally messed up the stem part of my first mold. I didn't spray the mold with release agent when I poured the 2nd batch of oomoo onto it... I was able to cut the goomba out, and I had a perfectly reasonably mold of that part of the keycap. So I've just kept on practicing casting with it when I mix up a batch of smooth-cast.
I like that short teal one in the first pictures. I don't know why, but I've come to prefer shorter artisan caps lately.
Elite desk wart divisionVery interesting. Noted for my own endeavors in the future.
I like that short teal one in the first pictures. I don't know why, but I've come to prefer shorter artisan caps lately.
I'm here to see the Goomba armyShow Image(http://a.fod4.com/misc/Bill%20Murray%20Cigarette%20Tree.gif)
Hi JT_Sea,
First of all: cool keycaps! Your project make me wanna make my own. Too bad I can't sculpt...
Here is a link to a video on making a silicone mold, maybe there are some tips in there to combat the bubbles.
https://www.youtube.com/watch?v=DEVi0mEaJJQ (https://www.youtube.com/watch?v=DEVi0mEaJJQ)
BTW: there is no way to say bubbles angrily. ;)
Have you tried using a pipette or a syringe to pour resin in. I tried it and it eliminated 99% of bubbles. Also I find more sprue holes work for me. Good luck with your project
Sent from my iPhone using Tapatalk
Yea the disposable ones. I made 9 holes all around the keycap edgeThank you! I'll see about ordering some shortly. If you wouldn't mind indulging some more questions. Do you use a pressure pot, and what do you use for the sprues? I've been using q-tips.
Sent from my iPhone using Tapatalk
Yea the disposable ones. I made 9 holes all around the keycap edgeThank you! I'll see about ordering some shortly. If you wouldn't mind indulging some more questions. Do you use a pressure pot, and what do you use for the sprues? I've been using q-tips.
Sent from my iPhone using Tapatalk
Great progress :)
I'll be posting the most likely mis-adventures of using a pressure pot very soon! And thanks for the tips, I think the pipetts will work very well in the future.Yea the disposable ones. I made 9 holes all around the keycap edgeThank you! I'll see about ordering some shortly. If you wouldn't mind indulging some more questions. Do you use a pressure pot, and what do you use for the sprues? I've been using q-tips.
Sent from my iPhone using Tapatalk
Same here, i also used q-tips as sprue. I'm still hesitating in using a pressure pot. And up till now from what i'm doing, my method seems working for me. So for a keycap with only a tiny bubble, it's fine for me.
Great progress :)Thanks! I'm glad it seems like there is progress, I feel like I've been in a backslide..
No photos of goombas today, but a minor update just the same.Show Image(http://i.imgur.com/QTD6FJG.jpg)Show Image(http://i.imgur.com/C2rAdCu.jpg)
I'm really excited for test casting tonight. We'll see how the bubbles fair now.
Bet those bubbles will be running for the hills.
Stay safe with that garage bomb, and post pix :p
For some reason I think most diy casting is done around 40-ishDis guy - http://www.amazon.com/Grizzly-H6329-Paint-Gauges-37288-Gallon/dp/B0007D2D7I
Im jelly. what brand?
Guys!Show Image(http://i.imgur.com/zEblpmE.jpg)Show Image(http://i.imgur.com/6fwY8PS.jpg)Show Image(http://i.imgur.com/oIpywBO.jpg)Show Image(http://i.imgur.com/q6YzZ4Z.jpg)Show Image(http://i.imgur.com/8rq6FcM.jpg)
Still not perfect, but at least its not bubbles that are causing the issues now!
Guys!Show Image(http://i.imgur.com/zEblpmE.jpg)Show Image(http://i.imgur.com/6fwY8PS.jpg)Show Image(http://i.imgur.com/oIpywBO.jpg)Show Image(http://i.imgur.com/q6YzZ4Z.jpg)Show Image(http://i.imgur.com/8rq6FcM.jpg)
Still not perfect, but at least its not bubbles that are causing the issues now!
They're like little gum drops!
Guys!Show Image(http://i.imgur.com/zEblpmE.jpg)Show Image(http://i.imgur.com/6fwY8PS.jpg)Show Image(http://i.imgur.com/oIpywBO.jpg)Show Image(http://i.imgur.com/q6YzZ4Z.jpg)Show Image(http://i.imgur.com/8rq6FcM.jpg)
Still not perfect, but at least its not bubbles that are causing the issues now!
They're like little gum drops!
Tasty grape gumdrops :p I can definitely see the difference with the latest casts
Guys!Show Image(http://i.imgur.com/zEblpmE.jpg)Show Image(http://i.imgur.com/6fwY8PS.jpg)Show Image(http://i.imgur.com/oIpywBO.jpg)Show Image(http://i.imgur.com/q6YzZ4Z.jpg)Show Image(http://i.imgur.com/8rq6FcM.jpg)
Still not perfect, but at least its not bubbles that are causing the issues now!
They're like little gum drops!
Tasty grape gumdrops :p I can definitely see the difference with the latest casts
Make it so.
Homemade Gummy Snacks Recipe
Prep time: 5 mins
Cook time: 5 mins
Total time: 10 mins
Serves: 16+
Ingredients
1 cup 100% fruit juice
2 tbsp grass-fed gelatin
Silicone candy molds or an 8" x 8" glass baking dish
Instructions
1. Pour the juice into small saucepan. Heat gently until the juice is very warm but not boiling.
2. Turn off the heat, and slowly pour the gelatin into the juice while whisking until it's incorporated. Repeat with the other tablespoon of gelatin.
3. Pour the mixture into silicone molds or an 8-inch by 8-inch glass baking dish that's been very lightly greased with coconut oil. You don't have to grease the silicone molds if you decide to use those. How many gummy snacks you'll end up with depends on how big your molds are.
4. Refrigerate the Homemade Gummy Snacks for at least 2 hours, then pop them out of the molds. You may want to freeze them for 15 minutes before you try to unmold.
5. Keep these gummy snacks refrigerated in a covered container. They keep for 3 to 5 days.
Guys!Show Image(http://i.imgur.com/zEblpmE.jpg)Show Image(http://i.imgur.com/6fwY8PS.jpg)Show Image(http://i.imgur.com/oIpywBO.jpg)Show Image(http://i.imgur.com/q6YzZ4Z.jpg)Show Image(http://i.imgur.com/8rq6FcM.jpg)
Still not perfect, but at least its not bubbles that are causing the issues now!
Really interesting to see the progress you're making (you move so fast!). Seeing a lot of improvement with the pressure pot! Those purp goombas are looking quite tasty d:Thanks! I feel like I"m moving so slow, I'm glad to see someone things I'm moving quickly.
great improvement!!!Thank you! I'm excited to start getting some caps out to my 'backers'. I sent them DM on reddit this morning with progress shots. Everyone seems pretty excited about the purps.
Really interesting to see the progress you're making (you move so fast!). Seeing a lot of improvement with the pressure pot! Those purp goombas are looking quite tasty d:Thanks! I feel like I"m moving so slow, I'm glad to see someone things I'm moving quickly.great improvement!!!Thank you! I'm excited to start getting some caps out to my 'backers'. I sent them DM on reddit this morning with progress shots. Everyone seems pretty excited about the purps.
Guys!Show Image(http://i.imgur.com/zEblpmE.jpg)Show Image(http://i.imgur.com/6fwY8PS.jpg)Show Image(http://i.imgur.com/oIpywBO.jpg)Show Image(http://i.imgur.com/q6YzZ4Z.jpg)Show Image(http://i.imgur.com/8rq6FcM.jpg)
Still not perfect, but at least its not bubbles that are causing the issues now!
Oh dude! This purple is soooooo nice. Casts are looking hella clean now. Can't wait to see moreThanks man! I may be able to cast a new one tonight. Got the new box of oomoo in last night, made the first 1/2 of the mold before bed and poured the 2nd part this morning before work. She's sitting in the pressure pot right now. Hopefully I didn't eff something up..
So I might have had a small nightmare about casting last night.. Guess that tells you something about whats on my mind currently.I love that you're active in posting updates. It looks like you're progressing nicely and it's nice to see you're excited about it.Really interesting to see the progress you're making (you move so fast!). Seeing a lot of improvement with the pressure pot! Those purp goombas are looking quite tasty d:Thanks! I feel like I"m moving so slow, I'm glad to see someone things I'm moving quickly.great improvement!!!Thank you! I'm excited to start getting some caps out to my 'backers'. I sent them DM on reddit this morning with progress shots. Everyone seems pretty excited about the purps.
I just really want gumdrops now :))(https://media1.giphy.com/media/3c9ubRSgiHXlS/200_s.gif)
Show Image(http://i.imgur.com/WGY08bb.jpg)Show Image(http://i.imgur.com/g68ZYeA.jpg)Show Image(http://i.imgur.com/uVd5Qai.jpg)Show Image(http://i.imgur.com/WtNp1JI.jpg)Show Image(http://i.imgur.com/FWhXpZb.jpg)Show Image(http://i.imgur.com/v3jPcaz.jpg)Show Image(http://i.imgur.com/ujrfuXp.jpg)Show Image(http://i.imgur.com/Vh2mcd5.jpg)Show Image(http://i.imgur.com/Yd2NVzh.jpg)
Still have one minor issue, but the second cap I cast last night didn't have it so I might have that sorted out. I did some heavy sanding on the master before making this mold, and now that I have a few to test I'll see how well they fit on my board + macropad today. Might need to do some more sanding..
Still have one minor issue, but the second cap I cast last night didn't have it so I might have that sorted out. I did some heavy sanding on the master before making this mold, and now that I have a few to test I'll see how well they fit on my board + macropad today. Might need to do some more sanding..
I'm sure you noticed the drastic improvement in the stem on the mold earlier, I'm hoping that a topre stem will work out equally well when curing under pressure.
Still have one minor issue, but the second cap I cast last night didn't have it so I might have that sorted out. I did some heavy sanding on the master before making this mold, and now that I have a few to test I'll see how well they fit on my board + macropad today. Might need to do some more sanding..
Just a heads up
I found topre and alps to need the same technique for making the stems mold work correctly.
And alps is super easy to get a decent cast of the stem, while topre is seemingly more difficult.
all that said, I dont have a pressure pot like you do...
:thumb:
Listerine Goomba?Love the name! I think I'll use it when I do a public sale.
I'm sure you noticed the drastic improvement in the stem on the mold earlier, I'm hoping that a topre stem will work out equally well when curing under pressure.
Still have one minor issue, but the second cap I cast last night didn't have it so I might have that sorted out. I did some heavy sanding on the master before making this mold, and now that I have a few to test I'll see how well they fit on my board + macropad today. Might need to do some more sanding..
Just a heads up
I found topre and alps to need the same technique for making the stems mold work correctly.
And alps is super easy to get a decent cast of the stem, while topre is seemingly more difficult.
all that said, I dont have a pressure pot like you do...
:thumb:
I've gotta say though, the pressure pot is almost like magic. I'm so glad I sold my SA sets & artisans& placeholders to get some better equipment. I'm really curious to know how a vac pot will help the process, and a high pressure valve in the pressure pot.Listerine Goomba?Love the name! I think I'll use it when I do a public sale.
Oh yea, the difference is night and day, and goes without saying.
Im really happy for you to be able to get this sweet set up.
I think you got the big change out of the way, and the vacuum will just be a nice compliment to the pressure.
IMO working on projects and creating stuff is much more satisfying than collecting cap sets and hoarding **** lol.
Oh yea, the difference is night and day, and goes without saying.
Im really happy for you to be able to get this sweet set up.
I think you got the big change out of the way, and the vacuum will just be a nice compliment to the pressure.
IMO working on projects and creating stuff is much more satisfying than collecting cap sets and hoarding **** lol.
From a creative standpoint its way more satisfying, but sometimes hoarding is great :D
from the front looks like goomba is eyeing on meThey're a creeper for sure. Always there, just watching..
You know they're just waiting for an opportunity to jump you...or is it the other way around?!from the front looks like goomba is eyeing on meThey're a creeper for sure. Always there, just watching..
You know they're just waiting for an opportunity to jump you...or is it the other way around?!from the front looks like goomba is eyeing on meThey're a creeper for sure. Always there, just watching..
Nice lil goombaNope, just ran out of resin when I was pouring the pseudo caps. The one with the crappy white teeth is the only cap amongst the bunch.
this one fit better?
Nice lil goombaNope, just ran out of resin when I was pouring the pseudo caps. The one with the crappy white teeth is the only cap amongst the bunch.
this one fit better?
Nice lil goombaNope, just ran out of resin when I was pouring the pseudo caps. The one with the crappy white teeth is the only cap amongst the bunch.
this one fit better?
Cool.
Have you made any blanks at all?
Almost all my caps are for personal use, so it depends on what you likeNice lil goombaNope, just ran out of resin when I was pouring the pseudo caps. The one with the crappy white teeth is the only cap amongst the bunch.
this one fit better?
Cool.
Have you made any blanks at all?
Nope, not yet. I should get around to it one of these days. I figure I'm doing good just getting the casting process down better, then I can expand after that.
Are blanks worth while to make?
Nice job!Agreed - I now understand why those caps fetch higher values.
I do not like doing double or triple shots, process wise, but damn do they make a cap look wayyy better.
Double shotsShow Image(http://i.imgur.com/dTgEERS.jpg)
I'm calling this set gloombasShow Image(http://i.imgur.com/CDUYAr2.jpg)
Tried mixing too little for the black, it didn't cure so thats all a goopy mess.
Next time, I'll not make that same mistake.Show Image(http://i.imgur.com/NpWYdh6.jpg)
Dark purpShow Image(http://i.imgur.com/VtzeXNN.jpg)
And don't forget your pillsShow Image(http://i.imgur.com/VS99aoS.jpg)
Double shotsShow Image(http://i.imgur.com/dTgEERS.jpg)
I'm calling this set gloombasShow Image(http://i.imgur.com/CDUYAr2.jpg)
Tried mixing too little for the black, it didn't cure so thats all a goopy mess.
Next time, I'll not make that same mistake.Show Image(http://i.imgur.com/NpWYdh6.jpg)
Dark purpShow Image(http://i.imgur.com/VtzeXNN.jpg)
And don't forget your pillsShow Image(http://i.imgur.com/VS99aoS.jpg)
Those are too many to keep for yourself. ;)
Double shotsShow Image(http://i.imgur.com/dTgEERS.jpg)
I'm calling this set gloombasShow Image(http://i.imgur.com/CDUYAr2.jpg)
Tried mixing too little for the black, it didn't cure so thats all a goopy mess.
Next time, I'll not make that same mistake.Show Image(http://i.imgur.com/NpWYdh6.jpg)
Dark purpShow Image(http://i.imgur.com/VtzeXNN.jpg)
And don't forget your pillsShow Image(http://i.imgur.com/VS99aoS.jpg)
Those are too many to keep for yourself. ;)
Gotta get the caps out to my backers first! But stay tuned to r/mk r/mm :D
How ever will you decide who gets single color and who gets the dubs?I'm thinking Random.org will be very valuable in my future. I also will add a caveat on my sale posts that anyone who wants to trade for caps I'm looking to acquire will get top priority! At least thats what I'm thinking now, I haven't worked out the specifics yet.
Idk how many people you sold to already, or did you just promise place holders?
How ever will you decide who gets single color and who gets the dubs?I'm thinking Random.org will be very valuable in my future. I also will add a caveat on my sale posts that anyone who wants to trade for caps I'm looking to acquire will get top priority! At least thats what I'm thinking now, I haven't worked out the specifics yet.
Idk how many people you sold to already, or did you just promise place holders?
I actually already have a private list of folks waiting for the goombas, I think I'll do a private sale first before I do a public one. Need to make sure everyone is okay with the quality first and foremost.
I have sent a few out as gifts to friends who have helped me out along the way, their reviews should provide valuable insight into the caps and if they'll stand up to a public release.
How ever will you decide who gets single color and who gets the dubs?I'm thinking Random.org will be very valuable in my future. I also will add a caveat on my sale posts that anyone who wants to trade for caps I'm looking to acquire will get top priority! At least thats what I'm thinking now, I haven't worked out the specifics yet.
Idk how many people you sold to already, or did you just promise place holders?
I actually already have a private list of folks waiting for the goombas, I think I'll do a private sale first before I do a public one. Need to make sure everyone is okay with the quality first and foremost.
I have sent a few out as gifts to friends who have helped me out along the way, their reviews should provide valuable insight into the caps and if they'll stand up to a public release.
that seems fair enough.
hopefully you can land a cap that you have been looking for in the process
How ever will you decide who gets single color and who gets the dubs?I'm thinking Random.org will be very valuable in my future. I also will add a caveat on my sale posts that anyone who wants to trade for caps I'm looking to acquire will get top priority! At least thats what I'm thinking now, I haven't worked out the specifics yet.
Idk how many people you sold to already, or did you just promise place holders?
I actually already have a private list of folks waiting for the goombas, I think I'll do a private sale first before I do a public one. Need to make sure everyone is okay with the quality first and foremost.
I have sent a few out as gifts to friends who have helped me out along the way, their reviews should provide valuable insight into the caps and if they'll stand up to a public release.
that seems fair enough.
hopefully you can land a cap that you have been looking for in the process
Gotta study the masters!
calves is right, you are the most dedicated I have seen in a while.
Not seeing an update here daily makes me worried. Are you ok? :))
calves is right, you are the most dedicated I have seen in a while.Not seeing an update here daily makes me worried. Are you ok? :))
Sorry guys, just busy with fam and working on getting keys setup for my backers. I actually do have some updates to post, I'll try to get those up today.
Just a hint :
4x mold tonight
New sculpt
Wifey sculpted a cap
Triple shot success!
Super excited to see new designs/sculpts! Killin' it sir!
calves is right, you are the most dedicated I have seen in a while.Not seeing an update here daily makes me worried. Are you ok? :))
Sorry guys, just busy with fam and working on getting keys setup for my backers. I actually do have some updates to post, I'll try to get those up today.
Just a hint :
4x mold tonight
New sculpt
Wifey sculpted a cap
Triple shot success!
calves is right, you are the most dedicated I have seen in a while.Not seeing an update here daily makes me worried. Are you ok? :))
Sorry guys, just busy with fam and working on getting keys setup for my backers. I actually do have some updates to post, I'll try to get those up today.
Just a hint :
4x mold tonight
New sculpt
Wifey sculpted a cap
Triple shot success!
Just relieved you're not lying in a ditch somewhere. :p
Oh did he? Yeah ship it to me, I'll make sure he gets it......calves is right, you are the most dedicated I have seen in a while.Not seeing an update here daily makes me worried. Are you ok? :))
Sorry guys, just busy with fam and working on getting keys setup for my backers. I actually do have some updates to post, I'll try to get those up today.
Just a hint :
4x mold tonight
New sculpt
Wifey sculpted a cap
Triple shot success!
Just relieved you're not lying in a ditch somewhere.
:D with a missing box of goombas!
btw your friend jumped in for a blind box gooms - you'll have that in your package.
:D You two can sort that out!Oh did he? Yeah ship it to me, I'll make sure he gets it......calves is right, you are the most dedicated I have seen in a while.Not seeing an update here daily makes me worried. Are you ok? :))
Sorry guys, just busy with fam and working on getting keys setup for my backers. I actually do have some updates to post, I'll try to get those up today.
Just a hint :
4x mold tonight
New sculpt
Wifey sculpted a cap
Triple shot success!
Just relieved you're not lying in a ditch somewhere.
:D with a missing box of goombas!
btw your friend jumped in for a blind box gooms - you'll have that in your package.
Minor update
I've got a few gooms ready to head out, but I think I'll wait till they are all ready to go out for my backers.Show Image(http://i.imgur.com/LvrIa7m.jpg)
4X is curing as I type this - also notice the far left stem..Show Image(http://i.imgur.com/AbVRB05.jpg)
First time triple shots have come out close to correct. The black could be darker, but I'm 100% happy with these guys.Show Image(http://i.imgur.com/HfDzTBi.jpg)
It was cold the other night in the basement, so when I pulled this one out it was still mushy, so I mushed it a little more. Sadly the stem didn't make it, otherwise this baby'd be on my keyboard.Show Image(http://i.imgur.com/AQ7sOuW.jpg)
New cap sculptingShow Image(http://i.imgur.com/DoAXVnG.jpg)Show Image(http://i.imgur.com/fTvD6Pr.jpg)
And as promised, my wife did a first pass on a sculpt. I present the golden snitchShow Image(http://i.imgur.com/ZIElItR.jpg)
Minor updatewould love to have that blue/teal haha. nice new sculpt
I've got a few gooms ready to head out, but I think I'll wait till they are all ready to go out for my backers.Show Image(http://i.imgur.com/LvrIa7m.jpg)
4X is curing as I type this - also notice the far left stem..Show Image(http://i.imgur.com/AbVRB05.jpg)
First time triple shots have come out close to correct. The black could be darker, but I'm 100% happy with these guys.Show Image(http://i.imgur.com/HfDzTBi.jpg)
It was cold the other night in the basement, so when I pulled this one out it was still mushy, so I mushed it a little more. Sadly the stem didn't make it, otherwise this baby'd be on my keyboard.Show Image(http://i.imgur.com/AQ7sOuW.jpg)
New cap sculptingShow Image(http://i.imgur.com/DoAXVnG.jpg)Show Image(http://i.imgur.com/fTvD6Pr.jpg)
And as promised, my wife did a first pass on a sculpt. I present the golden snitchShow Image(http://i.imgur.com/ZIElItR.jpg)
Oh man that chain chomp. :thumb:
Also those triple shots turned out very good! :cool:
Gotta say - Every time I press the one I have on my board I hear this in my head :
Holy Crap!!!! Both of those new sculpts look amazing. Absolutely love the detail work on the chain on your sculpture as well as the wing shape on your wife's! Great job man.Thanks dude! I can't wait to work on my wifes key, a few minor adjustments and some delicate casting and we might have an actual artisan on our hands.
Oh man that chain chomp. :thumb::D I hear that sound a lot when I'm pulling these guys out of the molds.
Also those triple shots turned out very good! :cool:
Gotta say - Every time I press the one I have on my board I hear this in my head :
would love to have that blue/teal haha. nice new sculptI appreciate the support, I should have a public sale over in r/mechmarket in the next few weeks. I'll post an update here as well when that happens.
The chain dude will look real nice!
and the snitch thing is awesome ! Id be worried about the replication of the snitch in the casting process, but if youre gentile, you can probably make it work!
The chain dude will look real nice!
and the snitch thing is awesome ! Id be worried about the replication of the snitch in the casting process, but if youre gentile, you can probably make it work!
I'm for sure worried about the snitch, but I think its worth a go. The oomoo 25 is really easy to stretch, so maybe... We'll see how it turns out.
The chain dude will look real nice!
and the snitch thing is awesome ! Id be worried about the replication of the snitch in the casting process, but if youre gentile, you can probably make it work!
I'm for sure worried about the snitch, but I think its worth a go. The oomoo 25 is really easy to stretch, so maybe... We'll see how it turns out.
I dont doubt that you can make it happen
I was just wondering about the ability to make a number of casts before the mold eventually gives in.
How did you make the alps cap? it looks really clean.
Whoa, an alps casting? :eek:Well I used a dsa blank for the goom master, and alps has dsa avail.. Thought I'd try and give the Alps clan some love. Sadly I won't be able to give any love to topre on this one.
Hadn't noticed you were running a post on here!Yup! Thanks for stopping by, I'm sure you noticed all dem purps this morning. I think one of them has your name on it.
Colors are really starting to look nice! That listerine green is turning into a nice turquoise almost.Thanks man, they really look blue when they are on their own but when you put them next to actual blue ones its easier to see their color.
I'm really digging that purple cap on the far left of the last picture. That cap reminds of a chameleon purple paint job. So awesomeGlad you like it, its a special for one of my backers.
Colors are really starting to look nice! That listerine green is turning into a nice turquoise almost.Thanks man, they really look blue when they are on their own but when you put them next to actual blue ones its easier to see their color.I'm really digging that purple cap on the far left of the last picture. That cap reminds of a chameleon purple paint job. So awesomeGlad you like it, its a special for one of my backers.Show Image(http://i.imgur.com/ZJeHlB1.jpg)
Colors are really starting to look nice! That listerine green is turning into a nice turquoise almost.Thanks man, they really look blue when they are on their own but when you put them next to actual blue ones its easier to see their color.I'm really digging that purple cap on the far left of the last picture. That cap reminds of a chameleon purple paint job. So awesomeGlad you like it, its a special for one of my backers.Show Image(http://i.imgur.com/ZJeHlB1.jpg)
Oh ok, it's a swirly type of cast I guess. Cool man, congrats, I bet the backers are really helping out with production :)
I think of all the things that I've learned so far this stands out to me.really great bro, the one infront of orange look like a ghost
I consider both of these caps failures. The one on the right, obviously it didn't make it and by the bubbles you can tell its pre pressure pot days and the one of the left while technically superior it has a divot in the chin.. I still have a long ways to go in my process, but man it feels nice to see the progress.Show Image(http://i.imgur.com/A64QFVG.jpg)Show Image(http://i.imgur.com/rMUOpFX.jpg)Show Image(http://i.imgur.com/sunH1jV.jpg)
And on a separate note, I've finished all the caps for my backers and I'll be mailing those out tomorrow morning. They deserve a big round of applause! It was really neat running a mini kick starter through the r/mk r/mm community, and I might do it again just to have people to write to a few times a week.Show Image(http://i.imgur.com/wUo3oNH.jpg)
The goomba fail armyShow Image(http://i.imgur.com/hs3YiAT.jpg)Show Image(http://i.imgur.com/31222JT.jpg)Show Image(http://i.imgur.com/l9Kl3HJ.jpg)
The goomba fail armyShow Image(http://i.imgur.com/hs3YiAT.jpg)Show Image(http://i.imgur.com/31222JT.jpg)Show Image(http://i.imgur.com/l9Kl3HJ.jpg)
What is the most common issue youve found in the failures?
What is the most common issue youve found in the failures?
They never had the drive to make something of themselves.
Seeing the progression of your work makes me happy! I see the dedication. Awesome! :thumb:Thanks!
Oh man, I wish I had read this last night. Seriously laughed out loud when I saw this this morning.What is the most common issue youve found in the failures?
They never had the drive to make something of themselves.
Thanks Romevi, now I can go to bed after a solid lol
Haha, this is a great photo:D
Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
What is that?Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
You should make a new design!Show Image(http://i.imgur.com/dmNiHMQ.png)
What is that?Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
You should make a new design!Show Image(http://i.imgur.com/dmNiHMQ.png)
What is that?Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
You should make a new design!Show Image(http://i.imgur.com/dmNiHMQ.png)
Its from a show called Rick and Morty. Its a planet sized head that crashes down and keeps shouting "Show me what you got"
What is that?Every time I see the blue it really pops!Yours is so light, hardly any color at all. Looks kinda like an ice cube. I'll be excited for you to get your package tomorrow/friday.
You should make a new design!Show Image(http://i.imgur.com/dmNiHMQ.png)
Its from a show called Rick and Morty. Its a planet sized head that crashes down and keeps shouting "Show me what you got"
I was going to say it looks like someone's messed up nutsack
I've seen the 'show me what you've got' gif and I've heard of the show before. But as you can imagine, I don't watch a lot of tv right now..
If you look here (https://www.pinterest.com/jmchorse/my-work/), you can see what I was working on prior to digging into keycap crafting. Still planning on finishing the OG 151, about halfway through atm.
Holy Schnikes, you have a lot of materials.It sucks to spend the money on that larger amounts, but man the price difference per oz of material.. Gotta do it, or I'd stop experimenting.
Holy Schnikes, you have a lot of materials.It sucks to spend the money on that larger amounts, but man the price difference per oz of material.. Gotta do it, or I'd stop experimenting.
Got dis here guy in the mail today. Black and Yellow swirl !Show Image(http://i.imgur.com/RB9LB79.jpg)
Super excited about this colorway! Great work dude! :thumb:
Got dis here guy in the mail today. Black and Yellow swirl !So stoked to see these bad boys arriving! And even more excited that they seem to be going over well.Show Image(http://i.imgur.com/RB9LB79.jpg)
Super excited about this colorway! Great work dude! :thumb:
Great stuff! Those buckets of silicone bring tears of happiness to my eyes. If I can offer a kind suggestion, I would say to use a platinum-cure silicone (like smooth-cast) instead of OOMOO after you use all of that. The platinum cure is a little more pricey, but lasts so much longer when you have complex or detailed molds that aren't smooth. I used to use OOMOO, and now I'll never go back.
Love your colors! I'll be watching your progress!
Testing some things outShow Image(http://i.imgur.com/GDOPuHI.jpg)
If only I had a topre board.. Maybe I have a friend who is loaning me one.
Testing some things outShow Image(http://i.imgur.com/GDOPuHI.jpg)
If only I had a topre board.. Maybe I have a friend who is loaning me one.
Glad you like them! Still can't believe you wanted all those rejectsTesting some things outShow Image(http://i.imgur.com/GDOPuHI.jpg)
If only I had a topre board.. Maybe I have a friend who is loaning me one.
Exciting stuff!
I know I already messaged you on reddit but I wanted to thank you again for these. They will be perfect for blind bags at my event. They also look great watching customers on my board at work. :))Show Image(http://i.imgur.com/yDYQI4R.jpg)
Testing some things outShow Image(http://i.imgur.com/GDOPuHI.jpg)
If only I had a topre board.. Maybe I have a friend who is loaning me one.
I take it you have an Alps board? ;)
I always was a SEGA kid. Having said that, I love this thread. As someone who loves crafting stuff and recently asked himself about the process of custom keycap making I loved the thread! You can really see the progress in every iteration. Thanks for sharing!! Please keep up what you're doing!!
You never posted how you did the multi stems :mad:
Did you follow the steps from the google doc or did you find a better process?
I neeeeed to know.
Love this thread, love this progress.
Very cool!
ETF is definitely helpful. keep it up
Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Considering it is basically helping competition.
its just a really cool, self supporting community
I get what you mean. Personally, bubbles aren't nearly as destructive for me as I have seen in others Cases. I'd say try before and if you need it, get it.Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Considering it is basically helping competition.
its just a really cool, self supporting community
I wouldn't see it like that, even with all the knowledge there appears to be a lot of skill and luck involved in great sculpting etc.
I like the retro reference here, and the transition from rough to polished, something I'm trying to do myself.
I think though without a pressure pot, the failures may eventually beat me down. I'll end up buying one and the wife will inevitably divorce me for my keycap madness.
Its a balancing act for sure, my wife gets annoyed at times. I try to break up the work though, so sometimes I get most of the evening to work on caps/casting etc and other I don't spend any time casting. That way she gets time together when she wants it, and I still get to work on my hobby. Plus one can sculpt caps while watching tv, so that helps as well.Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Considering it is basically helping competition.
its just a really cool, self supporting community
I wouldn't see it like that, even with all the knowledge there appears to be a lot of skill and luck involved in great sculpting etc.
I like the retro reference here, and the transition from rough to polished, something I'm trying to do myself.
I think though without a pressure pot, the failures may eventually beat me down. I'll end up buying one and the wife will inevitably divorce me for my keycap madness.
Very fast progress!Thank you!
Thinking about modifying under the Topre caps?
Not sure if you can with the DSA one's since they're so low already but I think you could add some thickness under the Topre & bridge the stem to make it stronger :)
I get what you mean. Personally, bubbles aren't nearly as destructive for me as I have seen in others Cases. I'd say try before and if you need it, get it.Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Considering it is basically helping competition.
its just a really cool, self supporting community
I wouldn't see it like that, even with all the knowledge there appears to be a lot of skill and luck involved in great sculpting etc.
I like the retro reference here, and the transition from rough to polished, something I'm trying to do myself.
I think though without a pressure pot, the failures may eventually beat me down. I'll end up buying one and the wife will inevitably divorce me for my keycap madness.
Sent from my local payphone
Don't get me wrong. They are leagues different in quality, I just noticed the variation in the destructiveness from. Bubbles can be quite largeIts a balancing act for sure, my wife gets annoyed at times. I try to break up the work though, so sometimes I get most of the evening to work on caps/casting etc and other I don't spend any time casting. That way she gets time together when she wants it, and I still get to work on my hobby. Plus one can sculpt caps while watching tv, so that helps as well.Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Considering it is basically helping competition.
its just a really cool, self supporting community
I wouldn't see it like that, even with all the knowledge there appears to be a lot of skill and luck involved in great sculpting etc.
I like the retro reference here, and the transition from rough to polished, something I'm trying to do myself.
I think though without a pressure pot, the failures may eventually beat me down. I'll end up buying one and the wife will inevitably divorce me for my keycap madness.
As for the pressure pot, if you can get one get one they are worth it from a casting perspective. I don't know how Moistgun does it, I would have quit already from frustration if I hadn't acquired one.Very fast progress!Thank you!
Thinking about modifying under the Topre caps?
Not sure if you can with the DSA one's since they're so low already but I think you could add some thickness under the Topre & bridge the stem to make it stronger :)
I'm 100% certain I'll do something to make the stem more reinforced. I'm sure it'll be a stop gap, until I can spend enough time on it to really get something worth while, but we'll cross that bridge when I get there.
On that note, does anyone know how far the travel is on these switches? How deep do the little divots need to be in order for the key to function properly?I get what you mean. Personally, bubbles aren't nearly as destructive for me as I have seen in others Cases. I'd say try before and if you need it, get it.Love this thread, love this progress.
Very cool!
Thank you so much! Glad you are enjoying it.ETF is definitely helpful. keep it up
So far I've been very surprised at how helpful everyone is, its really pretty awesome when you think about it.
Considering it is basically helping competition.
its just a really cool, self supporting community
I wouldn't see it like that, even with all the knowledge there appears to be a lot of skill and luck involved in great sculpting etc.
I like the retro reference here, and the transition from rough to polished, something I'm trying to do myself.
I think though without a pressure pot, the failures may eventually beat me down. I'll end up buying one and the wife will inevitably divorce me for my keycap madness.
Sent from my local payphone
I don't know how you do it man, more power to you for making quality caps sans pressure.
I always was a SEGA kid. Having said that, I love this thread. As someone who loves crafting stuff and recently asked himself about the process of custom keycap making I loved the thread! You can really see the progress in every iteration. Thanks for sharing!! Please keep up what you're doing!!
Thank you! I'll keep posting for sure. Problem is I'm over a small hump now, and just working on making enough product for a public sale, so nothing very interesting is going on.You never posted how you did the multi stems :mad:
Did you follow the steps from the google doc or did you find a better process?
I neeeeed to know.
Sorry! I was going to, then there were some issues with the multi stems that I had done. So I scratched them and moved on, and didn't have anything to post agin.
I'll see if I can get some photos of the topre setup I'm using.Show Image(http://i.imgur.com/LBOUHHe.jpg)
These guys have a ways to go, so I"m not 100% sure they'll make it into R1.
I've also been pestering the **** out of eat_the_foot about how he does things and that has helped a lot.
Show Image(http://i.imgur.com/jzXjsw7.jpg)
Show Image(http://i.imgur.com/jzXjsw7.jpg)
I know! Quite the magic trickShow Image(http://i.imgur.com/jzXjsw7.jpg)
HWS sent you your own caps?! That's crazy! :))
<3Show Image(http://i.imgur.com/jzXjsw7.jpg)
smashing it!
Show Image(http://i.imgur.com/jzXjsw7.jpg)
Show Image(http://i.imgur.com/jzXjsw7.jpg)
Brown Goomba Supreme!
Matching blanks are the best, though!
Thats so funny, I had no idea they'd be something people would be interested in, I just happened to have a blank mold from making spare caps for sculpting..Matching blanks are the best, though!
mhm, I agree :)
Pairs looking great! Keep the good news coming.
Thats so funny, I had no idea they'd be something people would be interested in, I just happened to have a blank mold from making spare caps for sculpting..Matching blanks are the best, though!
mhm, I agree :)
Maybe I'll toss in a blank or two when I do my R1 sale.
Getting better at mixing GIDShow Image(http://i.imgur.com/xj2DoBV.jpg)Show Image(http://i.imgur.com/M53T0VE.jpg)
Public sale starts on Wednesday!
https://www.reddit.com/r/MechanicalKeyboards/comments/4nwzgm/keyboard_art_bonk_r1_615/
Damn, it's starting to dawn on me I need a pressure pot. Caps look great.
I can't do that, it is n't gonna work inside a house :( Can't use the garage and it aint gonna be safe surely.
Early morning drop off at the USPS today :DShow Image(http://i.imgur.com/rLS9G5G.jpg)
Fun testsShow Image(http://i.imgur.com/9LCyFlg.jpg)
Oink OinkShow Image(http://i.imgur.com/vDKt7X4.jpg)
Early morning drop off at the USPS today :DShow Image(http://i.imgur.com/rLS9G5G.jpg)
Fun testsShow Image(http://i.imgur.com/9LCyFlg.jpg)
Oink OinkShow Image(http://i.imgur.com/vDKt7X4.jpg)
Fudge. That means I didn't win.
I say keep working on cleaning up that pig!
i like the 2nd from left if u decrease the length like not making the round shape on top of the caps
Show Image(http://i.imgur.com/mfBE55s.png)
Show Image(http://i.imgur.com/mfBE55s.png)
Show Image(http://i.imgur.com/mfBE55s.png)
Can you explain the tom and jerry meme?
Show Image(http://i.imgur.com/mfBE55s.png)
Can you explain the tom and jerry meme?
just me posting random tom and jerry images?
Show Image(http://i.imgur.com/mfBE55s.png)
Can you explain the tom and jerry meme?
just me posting random tom and jerry images?
Is that all it is, or are do they mean something?
Is Tom and Jerry going to be the next egg head or sax guy?
Been working on something else while I keep working on the topre Bonk.Show Image(http://i.imgur.com/rDTR2SQ.jpg)Show Image(http://i.imgur.com/nvGNOkr.jpg)Show Image(http://i.imgur.com/EREwv2S.jpg)
The bubs are real there on the minty/celets ones. Fortunately for me I'm only using them as tests.
Been working on something else while I keep working on the topre Bonk.Show Image(http://i.imgur.com/rDTR2SQ.jpg)Show Image(http://i.imgur.com/nvGNOkr.jpg)Show Image(http://i.imgur.com/EREwv2S.jpg)
The bubs are real there on the minty/celets ones. Fortunately for me I'm only using them as tests.
Been working on something else while I keep working on the topre Bonk.Show Image(http://i.imgur.com/rDTR2SQ.jpg)Show Image(http://i.imgur.com/nvGNOkr.jpg)Show Image(http://i.imgur.com/EREwv2S.jpg)
The bubs are real there on the minty/celets ones. Fortunately for me I'm only using them as tests.
Hot tamale, those red/purple blanks are on fire.
Been working on something else while I keep working on the topre Bonk.Show Image(http://i.imgur.com/rDTR2SQ.jpg)Show Image(http://i.imgur.com/nvGNOkr.jpg)Show Image(http://i.imgur.com/EREwv2S.jpg)
The bubs are real there on the minty/celets ones. Fortunately for me I'm only using them as tests.
So slick, especially the faded look of the purple modifiersShow Image(http://i.imgur.com/1VwezZV.gif)
So I tried a thing last nightShow Image(http://i.imgur.com/ZD4PoyM.jpg)Show Image(http://i.imgur.com/SsHNX3e.jpg)Show Image(http://i.imgur.com/aUIgDWY.jpg)Show Image(http://i.imgur.com/A0NeDm8.jpg)Show Image(http://i.imgur.com/LkX7fmS.jpg)
Lots o bubs but an interesting experiment thats mostly successful.
So I tried a thing last nightShow Image(http://i.imgur.com/ZD4PoyM.jpg)Show Image(http://i.imgur.com/SsHNX3e.jpg)Show Image(http://i.imgur.com/aUIgDWY.jpg)Show Image(http://i.imgur.com/A0NeDm8.jpg)Show Image(http://i.imgur.com/LkX7fmS.jpg)
Lots o bubs but an interesting experiment thats mostly successful.
Hold on, is that a peach gummy or a keycap?!Show Image(http://i.imgur.com/xSO1456.gif)
So I tried a thing last nightShow Image(http://i.imgur.com/ZD4PoyM.jpg)Show Image(http://i.imgur.com/SsHNX3e.jpg)Show Image(http://i.imgur.com/aUIgDWY.jpg)Show Image(http://i.imgur.com/A0NeDm8.jpg)Show Image(http://i.imgur.com/LkX7fmS.jpg)
Lots o bubs but an interesting experiment thats mostly successful.
Hold on, is that a peach gummy or a keycap?!Show Image(http://i.imgur.com/xSO1456.gif)
So I tried a thing last nightShow Image(http://i.imgur.com/ZD4PoyM.jpg)Show Image(http://i.imgur.com/SsHNX3e.jpg)Show Image(http://i.imgur.com/aUIgDWY.jpg)Show Image(http://i.imgur.com/A0NeDm8.jpg)Show Image(http://i.imgur.com/LkX7fmS.jpg)
Lots o bubs but an interesting experiment thats mostly successful.
Hold on, is that a peach gummy or a keycap?!Show Image(http://i.imgur.com/xSO1456.gif)
Just eat it and find out ;)
@JT_Sea, it looks pretty awesome!
Is dremel or a normal engraving knife better when making the prototype?
JT, did you make those HHKB Topre modifiers?
JT, did you make those HHKB Topre modifiers?Like Romevi said - sure did
So more experiments with modsShow Image(http://i.imgur.com/kUNopBf.jpg)Show Image(http://i.imgur.com/XutYsBm.jpg)Show Image(http://i.imgur.com/xpiFvp7.jpg)
These look cool when they aren't on a board, but I think they are a bit overwhelming once they are there. Oh well, just an experiment.
And more importantly, getting closer on the topre baseShow Image(http://i.imgur.com/KUYFeQs.jpg)Show Image(http://i.imgur.com/AoMpKMA.jpg)Show Image(http://i.imgur.com/2WxRas4.jpg)
Still not quite there, but much much better and loving the thick walls too.
Are the topre stems hard to get to fit properly?
Do the castings from the original topre caps not replicate the stem in the same way?
Are the topre stems hard to get to fit properly?
Do the castings from the original topre caps not replicate the stem in the same way?
They fit fine if you just take a cast of a regular cap, but the difference between thermoplastic and smoothcast liquidplastic is noticeable. The stem ends up being a little less sturdy because its thinner.
This is why you'll see reinforced stems from artisan makers, it just makes the whole thing much more solid and easier to deal with.
Got my bonks last friday! Colorway are so cool but Kinda hard to capture the real color. Thanks jtShow Image(http://uploads.tapatalk-cdn.com/20160703/d4811553ced769da1a16262226895bd9.jpg)
Sent from my iPhone using Tapatalk
Got my bonks last friday! Colorway are so cool but Kinda hard to capture the real color. Thanks jtYeeeeee!Show Image(http://uploads.tapatalk-cdn.com/20160703/d4811553ced769da1a16262226895bd9.jpg)
Sent from my iPhone using Tapatalk
Dat whale.:D
Dat whale.:DShow Image(https://img0.etsystatic.com/032/0/8803056/il_570xN.599622454_dk28.jpg)
Dat whale.:DShow Image(https://img0.etsystatic.com/032/0/8803056/il_570xN.599622454_dk28.jpg)
Just do it.Show Image(http://i.imgur.com/OfSWSXD.gif)
Dat whale.:DShow Image(https://img0.etsystatic.com/032/0/8803056/il_570xN.599622454_dk28.jpg)
Just do it.Show Image(http://i.imgur.com/OfSWSXD.gif)
What kind of whale is that sculpt?
Show Image(http://i.imgur.com/5MQmdFE.jpg)
Show Image(http://i.imgur.com/5MQmdFE.jpg)
Just wanted to thank you for this, especially because I only expected one Bonk to arrive.:D Glad you got one of the bonus sets. I had a few bonks + matching blanks when I did the raffle and just randomly sent them out. You are also the first person to say anything!Show Image(http://i.imgur.com/kAoTi76.jpg)
Show Image(http://i.imgur.com/NXRi1md.jpg)
So the red and purple ones are the newer slimmer profile. The brown is the original. We've been tossing around the name in the Seattle r/mk meetup slack of Regina.
I actually broke the master when I pulled it out of the mold, so I've been using the red one as the 'new master' and refining that one.
Finally have enough torpe bonks to make new molds. I'll be pouring my first topre mold tonight.
The newer mold looks much nicer, imo. Keep it up man!Thanks! Learn something new every time.
;)Show Image(http://i.imgur.com/NXRi1md.jpg)
So the red and purple ones are the newer slimmer profile. The brown is the original. We've been tossing around the name in the Seattle r/mk meetup slack of Regina.
I actually broke the master when I pulled it out of the mold, so I've been using the red one as the 'new master' and refining that one.
Finally have enough torpe bonks to make new molds. I'll be pouring my first topre mold tonight.Show Image(http://images6.fanpop.com/image/photos/32300000/Dr-Whale-Regina-once-upon-a-time-32351884-500-250.gif)?
Hehe, the pink whale is amazing :cool:
Ooh! Maybe a killer whale colorway? :p
killer :cool:
That Deadpool colorway is gonna look sick with the white pupils. What process do you use for multishotting the small details like the eyebrows and teeth?Time and toothpicks :|
Show Image(http://i.imgur.com/N5gv0Ri.jpg)
Show Image(http://i.imgur.com/6TulZD8.jpg)
More refinements for ReginaShow Image(http://imgur.com/NpoXys9.jpg)Show Image(http://imgur.com/MHD5LyL.jpg)Show Image(http://imgur.com/TXlbd7l.jpg)Show Image(http://imgur.com/JhtAQae.jpg)Show Image(http://imgur.com/meAXz13.jpg)
Show Image(http://i.imgur.com/6TulZD8.jpg)
More refinements for ReginaShow Image(http://imgur.com/NpoXys9.jpg)Show Image(http://imgur.com/MHD5LyL.jpg)Show Image(http://imgur.com/TXlbd7l.jpg)Show Image(http://imgur.com/JhtAQae.jpg)Show Image(http://imgur.com/meAXz13.jpg)
I want a whale.
Is Regina the official name of the cap?
#Regina4Eva:thumb:
Will there be a sale of the Reggies soon?Working on Topre & Alps bonks right now. But yeah, soon-ish
#Regina4Eva:thumb:Will there be a sale of the Reggies soon?Working on Topre & Alps bonks right now. But yeah, soon-ish
Marshmallow#Regina4Eva:thumb:Will there be a sale of the Reggies soon?Working on Topre & Alps bonks right now. But yeah, soon-ish
What's that white opaque Bonk to the far left in your avatar?
Show Image(http://i.imgur.com/BpnNRxW.jpg)Show Image(http://i.imgur.com/ZBDD8cY.jpg)Show Image(http://i.imgur.com/ySmc7BW.jpg)Show Image(http://i.imgur.com/Y8mikf0.jpg)
^ Topre w/matching esc
Show Image(http://i.imgur.com/BpnNRxW.jpg)Show Image(http://i.imgur.com/ZBDD8cY.jpg)Show Image(http://i.imgur.com/ySmc7BW.jpg)Show Image(http://i.imgur.com/Y8mikf0.jpg)
^ Topre w/matching esc
pls
Show Image(http://i.imgur.com/BpnNRxW.jpg)Show Image(http://i.imgur.com/ZBDD8cY.jpg)Show Image(http://i.imgur.com/ySmc7BW.jpg)Show Image(http://i.imgur.com/Y8mikf0.jpg)
^ Topre w/matching esc
pls
:epicsaxman:
Which?
Show Image(http://i.imgur.com/1ZFLYfl.jpg)
Show Image(http://i.imgur.com/1ZFLYfl.jpg)
Is that the process of how they've come? The final version is fantastic.
Are those DSA multi-shot blanks? :eek:Yes!
Pro Bonk Wrestlers?!They do look eerily like strong bad...
When is the next sale? I need more of this in my life...Ummmm, next week? I've got all the topre bonks done that I feel like making and I just need to finish them now.
Show Image(https://7chan.org/ch7/src/135410717930.gif)
Show Image(http://i.imgur.com/kS1TFls.jpg)
Show Image(http://i.imgur.com/kS1TFls.jpg)
Get a halfshell, roll it through those bonks, get 1-UPs.
(http://i.imgur.com/gWSyEYA.jpg)Show Image(http://i.imgur.com/kS1TFls.jpg)
Get a halfshell, roll it through those bonks, get 1-UPs.
Show Image(http://i.imgur.com/kS1TFls.jpg)
Get a halfshell, roll it through those bonks, get 1-UPs.Show Image(http://i.imgur.com/gWSyEYA.jpg)
Oh, snap! Matching blanks! :eek:
Wonder if Bonks will also come in matching colors with Regina... :rolleyes:
My kid is getting into kiibods, too. :thumb:
Ah, okay. They still look good; the thick walls are :thumb:.
I personally prefer Cherry profile, but the DSA blank looks really good with the Regina. The OEM one looks overpowering compared to the Regina.
Also, BS cap covers! ;D
Ah, okay. They still look good; the thick walls are :thumb:.
I personally prefer Cherry profile, but the DSA blank looks really good with the Regina. The OEM one looks overpowering compared to the Regina.
Also, BS cap covers! ;D
Those DSA triple shots are awesome!Thanks! There are actually 4 shots..
Okay, yeah: the DSA matching blanks look much better than OEM. :cool::thumb:
Show Image(http://i.imgur.com/lbZ3Tv6.jpg)
Awesome lookin' mods man.Show Image(http://i.imgur.com/lbZ3Tv6.jpg)
Thanks man! Trying to just make things I'd like to have on my board, glad to know others dig em.Show Image(http://i.imgur.com/lbZ3Tv6.jpg)
That looks great bro! You do your colors really well ;)
Yeah, the caps look fantastically colored.^^ Thanks bruh
Thanks!Awesome lookin' mods man.Show Image(http://i.imgur.com/lbZ3Tv6.jpg)
Are the modifiers hiding under the clouds? Where did the modifiers go?! :eek:Its raining inside the board :O
Very cool, love the colors. Great workThanks dude, can't wait to see your new sale.
It's like queso.Dude WTF, where are you getting your queso??
It's like queso.Dude WTF, where are you getting your queso??
Everybody knows the moon is made of queso, Grommit.
Looks like youve thickened the walls of the mods a little.I have spent a considerable amount of time thickening the sidewalls of my mods, and building up molds for that. I'm glad you noticed. I have a few testers locally, but if I need any more I'll post here :)
Is that the case?
Let us(me) know if you need product testers! haha
ModsShow Image(http://i.imgur.com/XqSM0AM.jpg)Show Image(http://i.imgur.com/aQL7lHx.jpg)Show Image(http://i.imgur.com/eVGFcWs.jpg)Show Image(http://i.imgur.com/eVGFcWs.jpg)Show Image(http://i.imgur.com/imDbBFY.jpg)Show Image(http://i.imgur.com/kz1PF4M.jpg)Show Image(http://i.imgur.com/O5MDwiZ.jpg)Show Image(http://i.imgur.com/O5MDwiZ.jpg)Show Image(http://i.imgur.com/XqSM0AM.jpg)Show Image(http://i.imgur.com/yHLuKx5.jpg)
Regina
Show Image(http://i.imgur.com/d0thWKa.jpg)
need.I might have yours ready on Friday if you'll be at James's house for the build party.
The Topre stuff is great, I wish I had an HHKB. :thumb: :thumb:Thanks! I'm hoping the hhkb crowd digs it. Might need to procure a realforce someday and go down that road..
Thanks! I'm hoping the hhkb crowd digs it. Might need to procure a realforce someday and go down that road..That would be marvelous! As someone considering a Realforce as their next board this makes me happy! :D
Don't see a white whale. :-[(https://i.ytimg.com/vi/kZtRJ14j3nE/maxresdefault.jpg)
Don't see a white whale. :-[Show Image(https://i.ytimg.com/vi/kZtRJ14j3nE/maxresdefault.jpg)
Don't see a white whale. :-[Show Image(https://i.ytimg.com/vi/kZtRJ14j3nE/maxresdefault.jpg)
Don't see a Booper. :-[
B&Don't see a white whale. :-[Show Image(https://i.ytimg.com/vi/kZtRJ14j3nE/maxresdefault.jpg)
Don't see a Booper. :-[
Thanks!Don't see a white whale. :-[Show Image(https://i.ytimg.com/vi/kZtRJ14j3nE/maxresdefault.jpg)
Don't see a Booper. :-[Show Image(http://static4.fjcdn.com/thumbnails/comments/Colbert+thread+go+go+go+_06ff0260dcc3bff0aa2e2aaffb6e10ff.gif)
But seriously, the whales are looking awesome
So I got a new batch of resin last night, it cures a little faster and is actually opaque. Finally get to use them tints I bought.. Also may or may not have picked up some fluorescent colors as well. Still figuring out new ratios.
Update, less bubbles but still there.Show Image(http://i.imgur.com/I7f46Ag.jpg)Show Image(http://i.imgur.com/xqy4A3L.jpg)Show Image(http://i.imgur.com/5ZnStmh.jpg)Show Image(http://i.imgur.com/MqsZj2p.jpg)Show Image(http://i.imgur.com/adfL0Y6.jpg)Show Image(http://i.imgur.com/2Pp39tM.jpg)Show Image(http://i.imgur.com/hfKJ1uF.jpg)
The little gang on my desk is growingShow Image(http://i.imgur.com/Wttasz7.jpg)Show Image(http://i.imgur.com/8bRIx7F.jpg)
And more mold troubles. The first two molds that I made turned out just fine, and now that I'm trying to build a 2 blank mold, I'm having issues with the stems. 3rd try was not the charm :( Time to pickup some pipettes if I can find them locally.Show Image(http://i.imgur.com/yF5vqG1.jpg)Show Image(http://i.imgur.com/D3adX8f.jpg)
Really thought I had it last night, used a small pick to try and get everything out of the stem.. Maybe 4th try.
Show Image(http://i.imgur.com/SeVTyg9.jpg)Show Image(http://i.imgur.com/BiDENZq.jpg)Show Image(http://i.imgur.com/lwB3NqX.jpg)
[img]http://i.imgur.com/WMXyZIQ.jpg[/img
Show Image(http://i.imgur.com/SeVTyg9.jpg)Show Image(http://i.imgur.com/BiDENZq.jpg)Show Image(http://i.imgur.com/lwB3NqX.jpg)
[img]http://i.imgur.com/WMXyZIQ.jpg[/img
It drank and pooped blood.
(https://s-media-cache-ak0.pinimg.com/236x/9e/03/26/9e0326f0a944eea7dfc50db3838a3b3c.jpg)Show Image(http://image.prntscr.com/image/50c24a14c0b3476b8e089d7f368e8daa.png)
Show Image(http://image.prntscr.com/image/50c24a14c0b3476b8e089d7f368e8daa.png)
Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Measuring by weight?
Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Measuring by weight?
Nay. By moisture.
Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Measuring by weight?
Nay. By moisture.
How many ml? Damn good matching btw
pretty much, PRETYY MUCH? YOU MEAN EXACTLY! ;) thanks bruhShow Image(http://image.prntscr.com/image/50c24a14c0b3476b8e089d7f368e8daa.png)
:))Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Looking good jt, they're pretty much identical :thumb:
Thanks moistNothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Measuring by weight?
Nay. By moisture.
How many ml? Damn good matching btw
Gallons daddy o
nice work jt
I don't measure in ml for the sizes that I'm doing, I use a scale and measure weight.Nothing terribly exciting to show, except I'm super happy with the color matching. I cast these two caps on two different days.Show Image(http://i.imgur.com/udy8Sp2.jpg)
Measuring by weight?
Nay. By moisture.
How many ml? Damn good matching btw
Just send some to me. I'll give them a loving home. :rolleyes:But they are so happy huddling together in their bucket!
Just send some to me. I'll give them a loving home. :rolleyes:I can help too. Espcially those coke bottle green ones
How much to buy a set? Love the work!
So I'm selling a few Reginas + matching blanks
https://www.reddit.com/r/mechmarket/comments/50fmqa/artisan_regina_blank_sale/
Show Image(http://i.imgur.com/xXZTlqD.jpg)Show Image(http://i.imgur.com/IMz9KJq.jpg)
Show Image(http://i.imgur.com/xXZTlqD.jpg)Show Image(http://i.imgur.com/IMz9KJq.jpg)
You know... I could always use some white glow in the dark HHKB mods...
I hope they will be part of a sale soon™
You know... I could always use some white glow in the dark HHKB mods...
I hope they will be part of a sale soon™
You know I hadn't included the white GID ones in the caps I've been prepping for my little sale. Perhaps we can work something out :D
Your keycaps and shots are clean. :pYou think flattery will get you your white whale??
You know... I could always use some white glow in the dark HHKB mods...
I hope they will be part of a sale soon™
You know I hadn't included the white GID ones in the caps I've been prepping for my little sale. Perhaps we can work something out :D
Let's hope you bring me good news. Turqouise GID Bonk and 1u blank definitely want some new family members (even though it's on a different board).
Your keycaps and shots are clean.You think flattery will get you your white whale??
Nvidia green mod caps sighting :eek:pls - sounds colors
Nvidia green mod caps sighting :eek:pls - sounds colors
Nvidia green mod caps sighting :eek:pls - sounds colors
hashtag confused :confused:
Nvidia green mod caps sighting :eek:pls - sounds colors
hashtag confused :confused:
Sounders
*poke poke poke* but.. what about these.. they glisten.. the glistening..rm -rf beat me up and stole them! j/k I gib'd to him.Show Image(http://i.imgur.com/EZzB0Q0.jpg)
*poke poke poke* but.. what about these.. they glisten.. the glistening..rm -rf beat me up and stole them! j/k I gib'd to him.Show Image(http://i.imgur.com/EZzB0Q0.jpg)
But if you are really longing for them, perhaps we can work something out in the future. They are double shot..
nice clean mods!!!What he said.
Not in the immediate future, the think with topre mods is there really aren't a lot of options on there. Mx on the other hand..nice clean mods!!!What he said.
I'd be interested in knowing if you plan on doing some in mx?
Halloween is coming.
and new experimentsShow Image(http://i.imgur.com/OhZOx3o.jpg)
What's the term for a group of whales? Herd?
What's the term for a group of whales? Herd?
A group of whales is commonly referred to as a pod.
What's the term for a group of whales? Herd?
A group of whales is commonly referred to as a pod.
Ah, thank you.
and new experimentsShow Image(http://i.imgur.com/OhZOx3o.jpg)
and new experimentsShow Image(http://i.imgur.com/OhZOx3o.jpg)
The experiment is a BS keycap? Please tell me!
Really nice work!
bye
That would look pretty cool on a IBM
That would look pretty cool on a IBM
That's what I'm saying, mang.
That would look pretty cool on a IBM
That would look pretty cool on a IBM
Actually - they look pretty decent in the garbage can :D
"good things" is a bit generous, trust me those ones need to be in the garbage.That would look pretty cool on a IBM
Actually - they look pretty decent in the garbage can :D
FINE. Throw good things away. See if I care :'(
I love the term "Keycap Crafting".:D thanks
I learned a lot reading this.
I'm wondering, do you degas your resin and then degas it again once it is poured into the mold?
I'm not sure but I think I've heard of artisans using de gasser with resin, I'll ask around. But pony is correct, I don't have one at this time.I learned a lot reading this.
I'm wondering, do you degas your resin and then degas it again once it is poured into the mold?
I haven't heard of any artisans degassing resin. Degassing the silicone is fairly common though, but I don't believe he does. After pouring the resin, it is usually put a in a pressure pot while setting.
:thumb:
nice work~
I learned a lot reading this.
I'm wondering, do you degas your resin and then degas it again once it is poured into the mold?
I haven't heard of any artisans degassing resin. Degassing the silicone is fairly common though, but I don't believe he does. After pouring the resin, it is usually put a in a pressure pot while setting.
You have amazing technique then.
I'm not sure but I think I've heard of artisans using de gasser with resin, I'll ask around. But pony is correct, I don't have one at this time.:thumb:
nice work~
Thanks!
if anyone wants to get rid of some 2.75u's... I'm happy to assist :DPm me, might have something sitting around
Some of them are, they also have pearl in them and may or may not have UV dye as well..
Show Image(http://i.imgur.com/EVaJgMP.jpg)
Show Image(http://i.imgur.com/EVaJgMP.jpg)
Curious George?
My daughter would love that cap. She's obsessed with the show.
I learned a lot reading this.
I'm wondering, do you degas your resin and then degas it again once it is poured into the mold?
I haven't heard of any artisans degassing resin. Degassing the silicone is fairly common though, but I don't believe he does. After pouring the resin, it is usually put a in a pressure pot while setting.
No eyes for George?
No eyes for George?
I'm down with the Owl, I have a friend that would absolutely love that thing. Keep us updated, your progress is looking good as usual!Thanks! I'm looking forward to doing a sale with these new sculpts, and maybe a matching bonk.
Hey Thanks for all the amazing info in this thread. I learn some new things and really enjoyed reading about your learning process. Your blanks are an inspiration and your new Owlie guy is lookin' sharp! Keep up the good work. :D
Had some more test casts last night. I'm diggin how these are turning out.Show Image(http://i.imgur.com/oFDCXjn.jpg)Show Image(http://i.imgur.com/22gMhoW.jpg?1)
Lol :DHad some more test casts last night. I'm diggin how these are turning out.Show Image(http://i.imgur.com/oFDCXjn.jpg)Show Image(http://i.imgur.com/22gMhoW.jpg?1)
ooooooOOOOooo I like the white one even better
or should i say whoooOOOooo
The white and black is still my fave owl. The added eyes on monkey are looking good. They add that definition that helps the 2nd color stay where it should.(something I'm trying to think about now when I make a new design)
I enjoy the clear with shiny dust. Clear with colored eyes would be pretty neat to see... :D
Nice progress, keep it up.
Decided to add eyes to the monkey now? :P
Your latest are awesome but--I think the world needs Stella artisans.. :cool:Part of me is trying to figure out just what that would look like. I think most people would confuse her for Dobby the house elf.
I learnt a lot from your posts because im starting to make artisans of my own, do you use smooth cast 300 fro your keys? also what dyes do you use?I do use smoothcast, but I use 326. I have a variety of dyes, some smooth on, some surfboard pigment and some alumilite. They all work well, if you can get the sample pack of smooth on dyes thats a great place to start.
Dobby is not nearly as cute as your doggo, fair enough :(I never realized she was actually a cat until someone pointed it out. She doesn't listen when you call her, she spends 99% of her time under a blanket on the sofa and she doesn't like going outside more than she has to :)
I learnt a lot from your posts because im starting to make artisans of my own, do you use smooth cast 300 fro your keys? also what dyes do you use?I do use smoothcast, but I use 326. I have a variety of dyes, some smooth on, some surfboard pigment and some alumilite. They all work well, if you can get the sample pack of smooth on dyes thats a great place to start.Dobby is not nearly as cute as your doggo, fair enough :(I never realized she was actually a cat until someone pointed it out. She doesn't listen when you call her, she spends 99% of her time under a blanket on the sofa and she doesn't like going outside more than she has to :)
Show Image(http://i.imgur.com/QtSnvCU.jpg)Show Image(http://i.imgur.com/pE1pAro.jpg)Show Image(http://i.imgur.com/62i5jgn.jpg)
Looking pretty good I think :)
Show Image(http://i.imgur.com/QtSnvCU.jpg)Show Image(http://i.imgur.com/pE1pAro.jpg)Show Image(http://i.imgur.com/62i5jgn.jpg)
Looking pretty good I think :)
White and Black :eek:
Starting to pick colorways for Beauford.Show Image(http://i.imgur.com/PoB6gAC.jpg)
Stella isn't impressed by artisans.Show Image(http://i.imgur.com/5cSIe5E.jpg)
Beauford and OtterophileShow Image(http://i.imgur.com/VUTDZfY.jpg)
Skittles :)Show Image(http://i.imgur.com/yUT6ERn.jpg)
The purp n blue didn't quite workout this cast, should have waited longer..Show Image(http://i.imgur.com/YY3BzpA.jpg)Show Image(http://i.imgur.com/0BilMDX.jpg)Show Image(http://i.imgur.com/UCdKdMK.jpg)
Hans still needs a little more work, the skin texture is complete.
Starting to pick colorways for Beauford.Show Image(http://i.imgur.com/PoB6gAC.jpg)
Stella isn't impressed by artisans.Show Image(http://i.imgur.com/5cSIe5E.jpg)
Beauford and OtterophileShow Image(http://i.imgur.com/VUTDZfY.jpg)
Skittles :)Show Image(http://i.imgur.com/yUT6ERn.jpg)
The purp n blue didn't quite workout this cast, should have waited longer..Show Image(http://i.imgur.com/YY3BzpA.jpg)Show Image(http://i.imgur.com/0BilMDX.jpg)Show Image(http://i.imgur.com/UCdKdMK.jpg)
Hans still needs a little more work, the skin texture is complete.
d you make it yourself?Excuse me, where is the mold metal cap, you can buy? Can you give me a website?
Thank! I contacted them to find their team in the GH artisan workshop, they launched a ~ I look at the development of an upgraded version will soon beStarting to pick colorways for Beauford.Show Image(http://i.imgur.com/PoB6gAC.jpg)
Stella isn't impressed by artisans.Show Image(http://i.imgur.com/5cSIe5E.jpg)
Beauford and OtterophileShow Image(http://i.imgur.com/VUTDZfY.jpg)
Skittles :)Show Image(http://i.imgur.com/yUT6ERn.jpg)
The purp n blue didn't quite workout this cast, should have waited longer..Show Image(http://i.imgur.com/YY3BzpA.jpg)Show Image(http://i.imgur.com/0BilMDX.jpg)Show Image(http://i.imgur.com/UCdKdMK.jpg)
Hans still needs a little more work, the skin texture is complete.
d you make it yourself?Excuse me, where is the mold metal cap, you can buy? Can you give me a website?
I think this is what you are asking about. http://techkeys.us/collections/accessories/products/synth
Amazing progress log! I'll be watching this thread for tips and tricks :)Great! Feel free to PM.