My design has a single switch on the bottom row that is .25u lower than the rest of the keys on the bottom row. Older versions of the Plate Builder used to draw a cutout on the middle layers of a sandwich case. But sometime during the summer, the Plate Builder stopped doing this. This isn't much of an issue for me because I can always make the cutout myself, should the need arise, but I mentioned it in case it is indicative of an issue that might affect other elements of the tool's function or in case it is related to another issue that someone has brought to your attention and could help you diagnose the issue. I included a mock-up of what the tool used to draw.
(Attachment Link)
Can you post me the KLE code you used to draw this plate so I can test?
When I added the ability to draw rotated clusters (like the ergodox), it ended up introducing some bugs that are hard to track down. Not sure how this one happened, but I will check it and see what is going on once you send me the code. Thanks for letting me know...
Here it is:
["~\n`","!\n1\n\n\nF1","@\n2\n\n\nF2","#\n3\n\n\nF3","$\n4\n\n\nF4","%\n5\n\n\nF5","^\n6\n\n\nF6","&\n7\n\n\nF7","*\n8\n\n\nF8","(\n9\n\n\nF9",")\n0\n\n\nF10","_\n-\n\n\nF11","+\n=\n\n\nF12",{c:"#999999"},"Home\n\n\n\nPgUp","End\n\n\n\nPgDn"],
[{w:1.5},"Tab",{c:"#cccccc"},"Q","W\n\n\n\nClick1","E\n\n\n\nMsUp","R\n\n\n\nClick2","T","Y\n\n\n\nIns","U\n\n\n\nHome","I\n\n\n\n↑","O\n\n\n\nEnd","P\n\n\n\nBackSpc","{\n[","}\n]",{c:"#999999",w:1.5},"|\n\\"],
[{w:1.75},"Ctrl",{c:"#cccccc"},"A","S\n\n\n\nMsLt","D\n\n\n\nMsDn","F\n\n\n\nMsRt","G","H\n\n\n\nPgUp","J\n\n\n\n←","K\n\n\n\n↓","L\n\n\n\n→",":\n;","\"\n'",{c:"#999999",w:2.25},"Enter"],
[{w:2.25},"Shift",{c:"#cccccc"},"Z","X","C","V","B","N\n\n\n\nPgDn","M\n\n\n\nDel","<\n,",">\n.","?\n/",{c:"#999999",w:1.75},"RShift",{c:"#6897ca"},"↑"],
["Esc",{c:"#999999",w:1.25},"Win",{w:1.25},"Alt","Del",{w:2},"Backspace",{c:"#6897ca",h:1.5},"Fn",{c:"#999999",w:2},"Space",{w:1.25},"Alt",{w:1.25},"RCtrl",{c:"#6897ca"},"←","→","↓"]
I used this design last night with the Plate Builder and I noticed that the padding is larger than it used to be. Previously 6mm padding was rendered at very nearly 6mm (my readings may have been off due to not selecting the second point perfectly vertical to the first point of the distance measuring tool in LibreCAD) but, last night, the padding was over 8 mm on the sides and top, and over 13mm on the bottom. I also tried reducing the function key to 1u vertical and dropping it .25u below the bottom row and it didn't change anything.