geekhack

geekhack Marketplace => Interest Checks => Topic started by: Rotwitt on Wed, 30 September 2020, 13:04:42

Title: [IC] POLYGON 65% - Prototype update 06-16-2021 - Prototype 3 has arrived!
Post by: Rotwitt on Wed, 30 September 2020, 13:04:42
POLYGON 65%


[attachimg=3 width 1280]


Long time no update

Almost 7 months has passed since i posted the initial IC here, and boy has things progressed. Time has been flying delays have been encountered, but Polygon has matured a lot in the meantime. The third prototype is on its way, all the colors have been revised, and the case has been completely redesigned from the bottom up between prototype 1 and 2, to meet my quality standards. It is now about time i show you the prototypes I have, my new website and some various other bits of information I'd like to share.

Information streams:

https://rotwitt.com (https://rotwitt.com)

Discord: https://discord.gg/29wyzeS
Instagram: https://www.instagram.com/byrotwitt/



Pictures of prototype 3

I've gotten rid of the wall of renders. It was a bit much.
Have a look at some pictures of the real thing instead.

[attach=15]


[attach=16]


[attach=17]


[attach=18]


[attach=19]



Pictures of prototype 2





[attach=14]
Enjoying some much needed sunlight


[attach=4]
Knob


[attach=5]
Back of the board


[attach=6]
Polygon weight


[attach=7]
Colour samples


[attach=9]
An actual picture of the PCB



Renders of prototype 3

As stated above - These are renders. Refer to the color samples above for RL colors.


[attach=10]
The new inside engraving being shown off


[attach=11]
The new and improved POLYGON logo


[attach=12]
Silver render because silver never gets enough love


[attach=13]
Plum with a brass knob. ilikeGOOOLD.gif





Render album:  https://imgur.com/a/PLpZlMu (https://imgur.com/a/PLpZlMu)

Old renders are available here: https://imgur.com/gallery/V72pL5I (https://imgur.com/gallery/V72pL5I)




Description


[attachimg=8 width=1500]

1 – Custom knob

A custom knob for the rotary encoder. It has a diameter of 30 mm.
It'll be available in any of the available colors and as a brass version.



2 – The top

The top features a 3mm chamfer alle the way around the upper edge.
It has been given a slight fillet, to increase comfort.


3 – The mounting system

The mounting system uses four stainless steel dowel pins, and four linear low-friction bearings provide a precise fit of the plate in the case.
It also acts a rail allowing you to tune the typing feel by changing the gaskets for harder or softer ones or use thicker gaskets on one side or the other.


4 – The gaskets

The Polygon uses 12 molded gaskets. Not having the gasket surround the entire plate, will allow the plate to resonate slightly, and use the plate to create Polygons sounds signature.
The gaskets will be replaceable and cutting files will be made available if you want to experiment with gaskets.


5 – The bottom

The bottom houses the USB-C daughterboard and features a POLYGON engraving and my logo.
During assembly, the top and the bottom comes together to a form a single unit, the top and bottom is then fastened to the slope.
Six low-profile bolts are used to secure top-bottom unit to the slope.

6 – The weight

The weight is fastened to the slope, through the left and right acoustic chambers.
It weighs in at around 1.1 kg (2.86lbs). The sharp edges of the weight is what gives Polygon its name.


7 – The slope

The slope has 3 rectangular cutouts, used as acoustic chambers and will provide a unique sound signature.
The chambers can be foamed and tuned to your likings, using the provided cuttings-files. You will also have the option to choose my preferred dampening solution.



Specs:


Case and weight:

• Typing angle: 7°
• Case material: Aluminium 6061
• Case finishing: Sandblasted and anodized
• Case colour: Silver, Gunmetal, Forest green, , Pantone 7605 c (Rose gold), Pantone 261 (Plum)
• Weight material: Brass
• Weight finishing: Sandblasting
• Approximate weight: 3,2 kg (8.37 lbs)
• Dampening: Neoprene
• Custom knob

• Case colours: Silver, Gun metal, Forest green, Navy, Rose gold, Plum


Plate:

• Plate material: Brass
• Plate thickness: 1,5mm
• Plate finish: Sandblasted

PCB:

• Layout support: ISO or ANSI
• Finish: ENIG and Custom PCB art
• Colour: Matte black
• Hotswap
• Rotary encoder
• Per key RGB
• AT Mega 32 MCU
• USB-C daughterboard
• QMK
• VIA

PRICING:

Case and PCB: 520-550 USD
Extra PCB: 80 USD
Plate foam: TBA
Extra plate: 30 USD

All prices without shipping.
These prices are unfortunately higher than the first estimates based on a quote from the manu. I recently asked for an updated quote that unfortunately came with a very significant price hike due to the current metal prices.
I am very sorry about this.





Layouts:

Each layout requires its own separate plate and PCB. The layout has been changed to accommodate wider support for more base kits.
It is important to me to provide you with the best product possible, which is way more feasible when the scale and complexity of the project is smaller.
This means that there are no plans of support for a soldered version of the PCB at the present.
IF YOU PLAN TO DESIGN YOUR OWN SOLDERABLE PCB PLEASE READ: You will need to make at least 6 switches hot-swappable. Send me a DM for details.

ISO layout:
[attach=2]


ANSI layout:
[attach=1]




Things to do:

• Wait for case Prototype 3
• Wait for PCB prototype 3
• Announce GB date and price within this month
• Ship the prototype out to reviewers
• Crack a mildly amusing dad-joke


Changes made:

• Completely redesigned the inner workings and fits to meet my quality standards
• Added engravings to the plate
• Changed the typing angle from 8 to 7 degrees
• Lowered the whole case to increase typing comfort
• Increased the knob size to 30 mm
• BIGGER Polygon logo and made the weight protrude slightly more. It also covers more of the back now.
• Optimizations made to the gasket system.
• Seamless sides
• Triangle engravings have been added to the inside of the case as well
• Added automotive-grade curves for seamless transitions from corners.



Additional notes

I will not be doing a polycarbonate version of the case because of quality concerns, when CNC-ing plastic.
Unfortunately the price has been subject to change as the metal prices have been rising according to my manu.



Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Wed, 30 September 2020, 13:06:57
Reserved
Title: Re: [IC] POLYGON 65%
Post by: Kokaloo on Wed, 30 September 2020, 13:16:43
(https://i.imgur.com/qaUtmWG.png)
Title: [IC] POLYGON 65%
Post by: jontseg on Wed, 30 September 2020, 13:21:29
Fantastic looking board. I love the visibility of the weight, the thick bezels, and clean lines throughout. The base colors are all solid, and I’m excited to see what other ones you come up with. Personally I’d love to see a yellow or beige color make it in :). GL!


Sent from my iPhone using Tapatalk
Title: Re: [IC] POLYGON 65%
Post by: Lizcuits on Wed, 30 September 2020, 13:33:36
Add a plum/maroon color and I will sell my soul for this
Title: Re: [IC] POLYGON 65%
Post by: finalarcadia on Wed, 30 September 2020, 13:40:02
Very unique design, though the bezels are too thick for me. Glwic

Sent from my Pixel 3 using Tapatalk

Title: Re: [IC] POLYGON 65%
Post by: a_turd on Wed, 30 September 2020, 15:55:02
Wow, looks gorgeous. I doubt my wallet will allow me to participate, but I'll be watching this one just in case.
Title: Re: [IC] POLYGON 65%
Post by: kohalified on Wed, 30 September 2020, 16:19:28
gib now plz
Title: Re: [IC] POLYGON 65%
Post by: General_Pretzel on Wed, 30 September 2020, 18:25:11
+1 to someone else's suggestion of Plum as a color option

I feel like the bezels are a bit too thick. I would also suggest moving the rotary encoder / knob up a bit, as it seems a bit too close to the keys below it.

Other than that, I absolutely love this.
Title: Re: [IC] POLYGON 65%
Post by: //gainsborough on Wed, 30 September 2020, 18:43:57
Holy bezels.  I like it, but the only thing that bothers me about it is that it's called "polygon" yet has very rounded corners >_<
Title: Re: [IC] POLYGON 65%
Post by: Zanhana on Wed, 30 September 2020, 21:45:28
Very promising, but I would only be in if it were possible to swap the function key to the left or right of the split spacebar
Title: Re: [IC] POLYGON 65%
Post by: FlitzDeelman on Thu, 01 October 2020, 04:32:47
It looks like indents in the bottom, running at angles to each other. It looks very nice!

But if so, are the rubber feet crossing those indents, and hanging in the air above them?

I’d prefer the rubber feet to be designed in accordance with the rest of the design. Am I seeing things wrong here?
Title: Re: [IC] POLYGON 65%
Post by: FlitzDeelman on Thu, 01 October 2020, 04:34:59
By the way, +1 for chonky bezels, please keep them if you can!
Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Thu, 01 October 2020, 10:06:42
I've received a lot of great feedback the past 20 or so hours, thanks a lot guys!
It's nice seeing so many people liking the design I've spent so much time on.
I'm sorry I haven't been able to answer any questions yet. I'll do my best to answer everyone individually

It's going to be a fun experience going through all of your suggestions, and see your take on my work and improve the design.
Please keep leaving your feedback, even if you don't like the board. I'll take reasonable changes into considerations

Two major-ish changes are coming:

The last of the changes are going affect the spacing between the clusters on the right side. Don't worry though, I'll do my best to keep it looking good.

Oh, and I'm excited to try out the different colour-schemes that has been suggested in the IC form. Thanks a lot everyone!


 
Title: Re: [IC] POLYGON 65%
Post by: pRoDeeD on Thu, 01 October 2020, 10:27:48
Damn! The gold looks super hot!
Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Thu, 01 October 2020, 11:21:30
Quote from: FlitzDeelman on Thu, 01 October 2020, 04:32:47
It looks like indents in the bottom, running at angles to each other. It looks very nice!

But if so, are the rubber feet crossing those indents, and hanging in the air above them?

I’d prefer the rubber feet to be designed in accordance with the rest of the design. Am I seeing things wrong here?
I'm glad you like it!
The rubber feet will have their own grooves to sit in like this:
[attach=1]
Title: Re: [IC] POLYGON 65%
Post by: leavenember on Thu, 01 October 2020, 11:48:23
Quote from: Rotwitt on Thu, 01 October 2020, 11:21:30
Quote from: FlitzDeelman on Thu, 01 October 2020, 04:32:47
It looks like indents in the bottom, running at angles to each other. It looks very nice!

But if so, are the rubber feet crossing those indents, and hanging in the air above them?

I’d prefer the rubber feet to be designed in accordance with the rest of the design. Am I seeing things wrong here?
I'm glad you like it!
The rubber feet will have their own grooves to sit in like this:
(Attachment Link)

How deep are those grooves/how thick are the feet? Seems kinda tall, but I'm interested to see what the effect of such thick feet, even while inset, would be on the sound.

Love the way that one groove goes up and continues into the weight design. GL!
Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Thu, 01 October 2020, 13:04:46
Quote from: leavenember on Thu, 01 October 2020, 11:48:23
Quote from: Rotwitt on Thu, 01 October 2020, 11:21:30
Quote from: FlitzDeelman on Thu, 01 October 2020, 04:32:47
It looks like indents in the bottom, running at angles to each other. It looks very nice!

But if so, are the rubber feet crossing those indents, and hanging in the air above them?

I’d prefer the rubber feet to be designed in accordance with the rest of the design. Am I seeing things wrong here?
I'm glad you like it!
The rubber feet will have their own grooves to sit in like this:
(Attachment Link)

How deep are those grooves/how thick are the feet? Seems kinda tall, but I'm interested to see what the effect of such thick feet, even while inset, would be on the sound.

Love the way that one groove goes up and continues into the weight design. GL!

The grooves aren't as deep as you'd think, only 1 mm. I'm looking foward to testing the sound!
Title: Re: [IC] POLYGON 65%
Post by: fakedSkill on Thu, 01 October 2020, 13:39:50
Def interested! Will the pcb be only hotswap or also solderable?
Title: Re: [IC] POLYGON 65%
Post by: perry4761 on Thu, 01 October 2020, 13:48:07
The knob is a bit too close to the nav keys for my taste, but this is otherwise a stunning design! I think that it would look better if the distance between the knob and nav keys matched the distance between the backspace and the knob.

EDIT: Welp I just reread the post and it looks like the change I suggested has already been made. Any updated renders to show what it looks like now?
Title: Re: [IC] POLYGON 65%
Post by: FlitzDeelman on Thu, 01 October 2020, 15:31:57
Quote from: Rotwitt on Thu, 01 October 2020, 11:21:30
Quote from: FlitzDeelman on Thu, 01 October 2020, 04:32:47
It looks like indents in the bottom, running at angles to each other. It looks very nice!

But if so, are the rubber feet crossing those indents, and hanging in the air above them?

I’d prefer the rubber feet to be designed in accordance with the rest of the design. Am I seeing things wrong here?
I'm glad you like it!
The rubber feet will have their own grooves to sit in like this:
(Attachment Link)
Great, that is a nice touch. Designed well indeed, to me as somebody who has not designed his own yet.
Title: Re: [IC] POLYGON 65%
Post by: mytommy on Thu, 01 October 2020, 16:56:34
hows the underglow going to appear when the case is aluminum?
Title: Re: [IC] POLYGON 65%
Post by: zoo on Fri, 02 October 2020, 01:25:02
that backside chonky  :p
Title: Re: [IC] POLYGON 65%
Post by: zoo on Fri, 02 October 2020, 01:25:21
interested in following the development of this design tho :)
Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Fri, 02 October 2020, 05:39:03
Quote from: mytommy on Thu, 01 October 2020, 16:56:34
hows the underglow going to appear when the case is aluminum?
That's a miscommunication on my part. It has per key rgb

Sendt fra min G8441 med Tapatalk

Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Fri, 02 October 2020, 07:35:34
Quote from: fakedSkill on Thu, 01 October 2020, 13:39:50
Def interested! Will the pcb be only hotswap or also solderable?
It will be hotswap only for now

Sendt fra min G8441 med Tapatalk

Title: Re: [IC] POLYGON 65%
Post by: KaosJ on Mon, 05 October 2020, 07:10:18
I really like the project, in fact i had a very similar project in mind (65% with big right knob), i guess i will dump it at this point since this is nice, i also like the bottom and weight design, so let me suggest something.

The current layout is a bit wrong imho (especially the bottom-row). Also some people can't really go split, on both spacebar and backspace splitted. Keep in mind that split is used by a minority of people, but apart that, i would totally go for the most standard ansi/iso you can and also support split as a second option. I believe this keyboard should have this layout https://i.imgur.com/Kacsuvo.png as standard and later support other layouts (e.g. split)
 
Also, the current knob is pretty much un-centered http://i.imgur.com/xXJUZzA.png so i would suggest to raise it up a bit to make it equal on all the sides (you have big bezels so you can do it).

In a nutshell, i think you have two options to make it more usable for people (0.25 vs 0.5 blockers) https://i.imgur.com/ZMSuTFA.png (the right part of the spacebar can be 1.5+1.5 eventually)
Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Mon, 05 October 2020, 10:19:58
Quote from: KaosJ on Mon, 05 October 2020, 07:10:18
I really like the project, in fact i had a very similar project in mind (65% with big right knob), i guess i will dump it at this point since this is nice, i also like the bottom and weight design, so let me suggest something.

The current layout is a bit wrong imho (especially the bottom-row). Also some people can't really go split, on both spacebar and backspace splitted. Keep in mind that split is used by a minority of people, but apart that, i would totally go for the most standard ansi/iso you can and also support split as a second option. I believe this keyboard should have this layout https://i.imgur.com/Kacsuvo.png as standard and later support other layouts (e.g. split)
 
Also, the current knob is pretty much un-centered http://i.imgur.com/xXJUZzA.png so i would suggest to raise it up a bit to make it equal on all the sides (you have big bezels so you can do it).

In a nutshell, i think you have two options to make it more usable for people (0.25 vs 0.5 blockers) https://i.imgur.com/ZMSuTFA.png (the right part of the spacebar can be 1.5+1.5 eventually)

First of all - Thanks for taking your time to provide your thoughts and feedback. Few people do so, so this is very much appreciated.

I'm glad you like the design. I agree with you on the layout. During the past weekend I have been reworking the layout to turn it into a more conventional one. Both to provide wider keycap compatibility, but also to allow people who don't normally use split-spacebar to use keycaps they already own. I will update the IC, with new renders showing both the ISO and ANSI layout, when I have all of it ready. Here's the new layout for ANSI and ISO: https://imgur.com/gallery/BQHwMKf (https://imgur.com/gallery/BQHwMKf)

I have also fixed the spacing around the knob [attach=1]

Hope you like the changes!
Title: Re: [IC] POLYGON 65%
Post by: kumori on Mon, 05 October 2020, 20:11:02
reminds me back in the old days... when i played roblox
Title: Re: [IC] POLYGON 65%
Post by: treeleaf64 on Mon, 05 October 2020, 22:21:30
Nice work glwic
Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Tue, 06 October 2020, 04:01:48
Quote from: perry4761 on Thu, 01 October 2020, 13:48:07
The knob is a bit too close to the nav keys for my taste, but this is otherwise a stunning design! I think that it would look better if the distance between the knob and nav keys matched the distance between the backspace and the knob.

EDIT: Welp I just reread the post and it looks like the change I suggested has already been made. Any updated renders to show what it looks like now?
I am currently working on some new renders, so they should be ready soon

Sendt fra min G8441 med Tapatalk

Title: Re: [IC] POLYGON 65%
Post by: Rotwitt on Tue, 06 October 2020, 05:34:40
Quote from: Kokaloo on Wed, 30 September 2020, 13:16:43
Show Image
(https://i.imgur.com/qaUtmWG.png)

Feel free to share your thoughts on the design

Sendt fra min G8441 med Tapatalk

Title: Re: [IC] POLYGON 65%
Post by: Lizcuits on Tue, 06 October 2020, 15:17:17
Quote from: Rotwitt on Mon, 05 October 2020, 10:19:58

First of all - Thanks for taking your time to provide your thoughts and feedback. Few people do so, so this is very much appreciated.

I'm glad you like the design. I agree with you on the layout. During the past weekend I have been reworking the layout to turn it into a more conventional one. Both to provide wider keycap compatibility, but also to allow people who don't normally use split-spacebar to use keycaps they already own. I will update the IC, with new renders showing both the ISO and ANSI layout, when I have all of it ready. Here's the new layout for ANSI and ISO: https://imgur.com/gallery/BQHwMKf (https://imgur.com/gallery/BQHwMKf)

I have also fixed the spacing around the knob (Attachment Link)

Hope you like the changes!

I definitely think this was the way to go! The only other change I would recommend is adding some sort of blocker or changing the 3 1u keys to the right of the spacebar to 2 1.5u keys. I think more people will have keys to support that from most base kits. Otherwise, I think it's a really good change, I'm super excited to see the new renders!

I am sad we are losing split spacebar support, but having 6.25 is definitely the way to go for broad compatibility. Maybe a solderable PCB in the future with split space support?

Also... maroon... burgundy? Maybe? Perhaps? Pretty please?

Looking forward to following this project more!
Title: Re: [IC] POLYGON 65%
Post by: KaosJ on Wed, 07 October 2020, 03:06:37
Quote from: Rotwitt on Mon, 05 October 2020, 10:19:58
Quote from: KaosJ on Mon, 05 October 2020, 07:10:18
I really like the project, in fact i had a very similar project in mind (65% with big right knob), i guess i will dump it at this point since this is nice, i also like the bottom and weight design, so let me suggest something.

The current layout is a bit wrong imho (especially the bottom-row). Also some people can't really go split, on both spacebar and backspace splitted. Keep in mind that split is used by a minority of people, but apart that, i would totally go for the most standard ansi/iso you can and also support split as a second option. I believe this keyboard should have this layout https://i.imgur.com/Kacsuvo.png as standard and later support other layouts (e.g. split)
 
Also, the current knob is pretty much un-centered http://i.imgur.com/xXJUZzA.png so i would suggest to raise it up a bit to make it equal on all the sides (you have big bezels so you can do it).

In a nutshell, i think you have two options to make it more usable for people (0.25 vs 0.5 blockers) https://i.imgur.com/ZMSuTFA.png (the right part of the spacebar can be 1.5+1.5 eventually)

First of all - Thanks for taking your time to provide your thoughts and feedback. Few people do so, so this is very much appreciated.

I'm glad you like the design. I agree with you on the layout. During the past weekend I have been reworking the layout to turn it into a more conventional one. Both to provide wider keycap compatibility, but also to allow people who don't normally use split-spacebar to use keycaps they already own. I will update the IC, with new renders showing both the ISO and ANSI layout, when I have all of it ready. Here's the new layout for ANSI and ISO: https://imgur.com/gallery/BQHwMKf (https://imgur.com/gallery/BQHwMKf)

I have also fixed the spacing around the knob (Attachment Link)

Hope you like the changes!

Looks perfect to me! I really dig it, it has everything i want

The only other things that comes to mind:
Title: Re: [IC] POLYGON 65%
Post by: fakedSkill on Wed, 07 October 2020, 13:47:56
Looks really amazing, wondering how it would look with thinner lines on the back, and straight not round corners.
Title: Re: [IC] POLYGON 65%
Post by: Infallible on Thu, 15 October 2020, 15:27:42
Beautiful work on the aesthetic design. The bezels are a touch too thick for my liking, but that is preference and I think you've done a great job with what you were going for. Really like the cutouts on the bottom and the way the weight frames the usb cutout.
Title: Re: [IC] POLYGON 65%
Post by: teesui on Thu, 15 October 2020, 16:38:30
Super interested. Like others have mentioned, I too, do find the bezels a tad too thick, but it adds to the overall aethetics. just wondering if there could be some contrast colours to the knob? since if it's the same colour as the case, I do find that there is a bit of an imbalance to the aesthetics, where there's an overwhelmingly concentration of the case colour (in comparison to the other corners) in that top right corner. is there an option to pick the knob from the other case colours  or does the knob have to match the case?
Title: Re: [IC] POLYGON 65%
Post by: Cubic // esc lab on Thu, 15 October 2020, 17:58:01
This is aesthetic
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Mon, 19 October 2020, 15:44:01
A rather big update has been made. It includes a new Layout for ISO and ANSI, a bunch of new renders, new placement of the rotary encoder and an exploded view of the keyboard.
The specs has always been expanded with two important things: GMK and VIA.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Lulzthax_ on Mon, 19 October 2020, 16:01:29
Quite fond of the design on the bottom as well as the green pantone. For my personally I feel like the feet somewhat interrupt the design crossing through them and it might benefit from corner feet, objective opinion of course ;)
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Lizcuits on Mon, 19 October 2020, 16:23:35
the madlad actually did it
Quote
Add a plum/maroon color and I will sell my soul for this

(https://geekhack.org/index.php?action=dlattach;topic=108832.0;attach=253969;image)

I'll take 28

Please make a banner for this IC so I can shill for it everywhere I go
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: zeejet on Mon, 19 October 2020, 17:04:48
Just here to show love for the design aesthetic and the brassed Leica M6 in the renders; you have good taste sir. Unfortunately, I'm a thin bezel type of dude :(
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: kohalified on Mon, 19 October 2020, 17:16:26
Loving the new colors!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Glueeater on Mon, 19 October 2020, 17:18:32
New colors & design look great!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Current Keyboards on Mon, 19 October 2020, 21:38:39
I love this design. Honestly the only thing I dislike is the brass bezel at the front but I think I'm very much in the minority there. Nice work. Will watch.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Tue, 20 October 2020, 02:01:42
Happy to see you like the changes I've been working on. Next on the list is preparing for prototyping the PCB and the case. It'll probably tak some weeks to get there, but that's part of the fun!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: atlanticise on Tue, 20 October 2020, 02:56:01
I'M ALL IN ON THAT JUICY PLUM YOOOOOOO
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Lizcuits on Tue, 20 October 2020, 09:51:46
Quote from: atlanticise on Tue, 20 October 2020, 02:56:01
I'M ALL IN ON THAT JUICY PLUM YOOOOOOO

retweet
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Ben2707 on Tue, 20 October 2020, 10:25:50
Corners are awesome, thick boi bezels are slowly becoming a thing and I love it. Great way to expand table presence without being too flashy. Tasteful design. Not sure about rotary encoder taking up such a huge spot on the upper corner as it throws the design off a little but overall looks great. Will be in for this if budget allows.

Also +1 on yellow to match dualshot/nautlius.

GLWIC!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Icemanrec on Tue, 20 October 2020, 10:38:30
This looks like something I could really like, is there a discord for this yet?
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: fluxlab on Tue, 20 October 2020, 12:22:43
Love these thick bezel boards 🥰
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: dtywill on Tue, 20 October 2020, 17:03:03
Quote from: Icemanrec on Tue, 20 October 2020, 10:38:30
This looks like something I could really like, is there a discord for this yet?
Second this, will updates mainly be posted here or is there a Discord server?


Sent from my iPad using Tapatalk
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Friendship on Tue, 20 October 2020, 17:35:07
looks very neat and the color options are wild! any chance at split backspace support?
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: kohalified on Tue, 20 October 2020, 18:25:15
Banner please.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: MadBinton on Tue, 20 October 2020, 18:50:37
I'm surprised how good the Plum looks. Never thought I'd be considering that colour, but here it looks really bold.
Keeping an eye on this one. Would join a discord too.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Wed, 21 October 2020, 00:44:40
Hey everyone! I don't have a discord yet, but I'll make sure to make one, so you guys can follow the progression
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: hiddensong on Wed, 21 October 2020, 06:29:15
thicc bezel life!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Wed, 21 October 2020, 10:41:27
Quote from: Icemanrec on Tue, 20 October 2020, 10:38:30
This looks like something I could really like, is there a discord for this yet?

Hey! Happy to hear you like it!

I 've created a discord server which you can find here: https://discord.gg/29wyzeS
I also have an instagram which you can find here: https://www.instagram.com/byrotwitt/
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Wed, 21 October 2020, 10:43:31
Quote from: MadBinton on Tue, 20 October 2020, 18:50:37
I'm surprised how good the Plum looks. Never thought I'd be considering that colour, but here it looks really bold.
Keeping an eye on this one. Would join a discord too.

Quote from: dtywill on Tue, 20 October 2020, 17:03:03
Quote from: Icemanrec on Tue, 20 October 2020, 10:38:30
This looks like something I could really like, is there a discord for this yet?
Second this, will updates mainly be posted here or is there a Discord server?


Sent from my iPad using Tapatalk

I 've just created a discord server which you can find here: https://discord.gg/29wyzeS

I also have an instagram which you can find here: https://www.instagram.com/byrotwitt/
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: asciisii on Wed, 21 October 2020, 15:36:36
Like the design. Unfortunately can't even consider joining without split backspace
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Havattack on Wed, 21 October 2020, 20:34:04
Quote from: fluxlab on Tue, 20 October 2020, 12:22:43
Love these thick bezel boards 🥰

Amen! This, the M0110  (modern and vintage) are some of my favorite looking boards.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Casserole on Wed, 21 October 2020, 23:59:02
Those bezels are noiccceee


Sent from my iPhone using Tapatalk
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: kohalified on Thu, 22 October 2020, 12:10:06
geekhack link is invalid
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Thu, 22 October 2020, 14:19:35
Quote from: kohalified on Thu, 22 October 2020, 12:10:06
geekhack link is invalid
Should be fixed now!

Sendt fra min G8441 med Tapatalk

Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: dtywill on Thu, 22 October 2020, 22:53:28
Is there a straight on photo of the side profile?


Sent from my iPhone using Tapatalk
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: 3yatt on Sun, 21 February 2021, 12:15:51
Any updates on this project? Would love for this fantastic idea to come to fruition!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Havattack on Sun, 21 February 2021, 14:47:57
Quote from: 3yatt on Sun, 21 February 2021, 12:15:51
Any updates on this project? Would love for this fantastic idea to come to fruition!

Yup, just join the discord buddy. The links in the OP. (I hate having to sign up for yet another new thing, but just do it. Most of the IC's posted on this site get updated far more regularly on their receptive discord then on geekhack,
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: AshF on Mon, 22 February 2021, 02:23:25
This looks really interesting and will certainly be keeping my eyes peeled. Super amazing that you have incorporated hot swap with an ISO offering + RGB if required. Excellent work!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Mon, 22 February 2021, 03:43:25
Quote from: 3yatt on Sun, 21 February 2021, 12:15:51
Any updates on this project? Would love for this fantastic idea to come to fruition!
There’s been a whole lot of progress since the last update including a case prototype! I am currently waiting for the PCB prototype to arrive
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Mon, 22 February 2021, 03:44:43
Quote from: AshF on Mon, 22 February 2021, 02:23:25
This looks really interesting and will certainly be keeping my eyes peeled. Super amazing that you have incorporated hot swap with an ISO offering + RGB if required. Excellent work!
Thank you!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Mon, 22 February 2021, 13:33:09
Update 02/22-2021

Thought I'd give a short and sweet update here today as well:

I've received a couple of pictures of the PCB from the manu and it turns out they made the wrong version.
This means that the whole project will be delayed by at least a few weeks, which sucks pretty badly.

On the bright side I can now show you the design of the PCB, which i hope you like:

[attach=1]



Bonus pics of the Polygon case Prototype:

[attach=2]


[attach=3]
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: StrangPrisoner on Mon, 22 February 2021, 17:26:52
Digging the PCB. Simple and fits the motif. :thumb:
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Pach on Mon, 22 February 2021, 19:14:45
Love the aesthetic although I'm personally not a fan of thicc bois
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Havattack on Mon, 22 February 2021, 20:30:59
Probably my fav looking keeb ever. I love this thing.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: firstworldproblems on Mon, 22 February 2021, 20:41:43
Love those thicc bezels

Sent from my Pixel 4 using Tapatalk

Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Timception on Tue, 23 February 2021, 13:08:47
Looks noice, price?
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: kdam39 on Tue, 23 February 2021, 23:36:27
good looking board. 65% is as low as I usually go but your design choice here makes the board looking very comfortably good.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Slade0ne on Fri, 26 March 2021, 21:22:49
I can't wait, but I must.  Awesome Design
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: PuddingPug on Fri, 26 March 2021, 21:34:58
I told myself no more 65% but dang! This board is beautiful!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Techdude594 on Fri, 26 March 2021, 22:55:33
This looks fantastic! Big bezels are beautiful! Those new protos are very promising!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: PuddingPug on Sat, 27 March 2021, 02:05:04
Would love more pictures of the prototype!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Sat, 27 March 2021, 05:49:51
Quote from: PuddingPug on Sat, 27 March 2021, 02:05:04
Would love more pictures of the prototype!

Sure!

[attach=1]

[attach=2]

[attach=3]

Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Havattack on Sat, 27 March 2021, 15:25:39
Give me that.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: dotmkb on Mon, 29 March 2021, 11:02:00
This looks great, love the detailing on the bottom. Loving all these boards recently with thicc bezels.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: hottrout on Wed, 31 March 2021, 03:40:16
Great watching the progress on this.  You really have something here.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: zykie1018 on Thu, 01 April 2021, 21:52:54
Hope this will push through. Really excited for this
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Extra Fox on Thu, 01 April 2021, 22:13:32
Mi gusta.
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: Rotwitt on Fri, 16 April 2021, 05:50:52
16-04-2021

I ordered the new case prototype Thursday last week so it should be here within the next two weeks.

Here’s a little list with some info on my order:


I ordered new samples of Navy, Green, Plum, black/dark gray and rose gold.
Here’s some of the changes since the first colour samples:


I also ordered two different kinds of plates: one with relief cuts and one without them(Both types ANSI and ISO). The relief cuts are meant for testing at the moment and might not make it into the final product. Both plate types are in brass


The changes since the first revision includes the following:


Cheers and have a nice weekend!
Title: Re: [IC] POLYGON 65% - Updated 19-10-2020: New layout, updated specs, exploded view
Post by: jabe8i on Fri, 16 April 2021, 06:01:33
Why must I be cursed to fork over money to people who design thicc bezel boards
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: AshF on Fri, 16 April 2021, 06:04:08
This looks amazing! Super work.
ISO / Hotswap / Per  Key RGB / looks fantastic / perfect (IMO) blockers separating arrow and keys - this is an instabuy if this goes to GB (fingers crossed - unlimited).

PS. Any yellow colourway?

Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: Nascent on Fri, 16 April 2021, 07:20:46
Really nice design! Hotswap ISO with gasket mount is not something you see everyday. Will be following closely. Congrats on a fantastic looking board!
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: Rotwitt on Fri, 16 April 2021, 15:34:46
Quote from: AshF on Fri, 16 April 2021, 06:04:08
This looks amazing! Super work.
ISO / Hotswap / Per  Key RGB / looks fantastic / perfect (IMO) blockers separating arrow and keys - this is an instabuy if this goes to GB (fingers crossed - unlimited).

PS. Any yellow colourway?
Thanks a lot!

I probably won’t introduce any more colours to the currently planned run, but I won’t rule it out in a future run if there’s enough interest!


Sent from my iPhone using Tapatalk
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: Slade0ne on Wed, 21 April 2021, 00:14:47
Would flex cuts have an effect on the brass plate?  I'm not sure that's why I am asking.
Great job with the board, I can see you are really dedicated to making it as perfect as possible, truly admirable.
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: UGunaLOSE on Wed, 21 April 2021, 13:09:19
Looks awesome (I'm a big fan of the thicc bezels)!!
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: antsinyourpants on Wed, 21 April 2021, 20:49:21
Absolutely in love with everything about this board! Very much appreciate your detailed update and I can't wait to hear more about the latest prototypes.
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: SDKCAMPING on Wed, 21 April 2021, 21:37:09
 i have been seeing some old IC's bumped for updates... glad to see this ic is still in the works and not left to wither!
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: 3yatt on Mon, 07 June 2021, 01:41:04
WHERE IS THIS?? I NEEEEEED IT!!

but really hope all is well and I want this real bad.
Title: Re: [IC] POLYGON 65% - Updated 16-04-2021: Case Revision 2 has been ordered
Post by: Rotwitt on Mon, 07 June 2021, 15:12:00
Don't worry, the project is still alive! I just made a major update just for you. Thanks for keeping up with this project!

Quote from: 3yatt on Mon, 07 June 2021, 01:41:04
WHERE IS THIS?? I NEEEEEED IT!!

but really hope all is well and I want this real bad.
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: Neely_12 on Tue, 08 June 2021, 00:58:43
Been following for a while, am Im super excited for this. Amazing board you've got here
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: RoyalOak88 on Tue, 08 June 2021, 03:59:27
Really nice design! The fact that it has ISO hotswap is the cherry on top.
Eager for this  ;D
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: antsinyourpants on Tue, 08 June 2021, 12:07:10
Whoo! New website is looking slick. And those colour samples look great too.
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: Techdude594 on Sat, 12 June 2021, 04:24:17
Amazing update! Man that plum is stunning! ;D
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: RicWatt on Sat, 12 June 2021, 05:03:30
Oh its a thick one, very nicely done. GLWS
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: hayasaka on Sat, 12 June 2021, 05:06:14
wow, sleek and real thick at the same time.  :) GLWIC
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: Rotwitt on Sun, 13 June 2021, 15:06:17
Thanks for the support and kind words everyone! It’s been quite a journey so far and I look forward to announcing the GB date (the GB will be some time late July if you missed it)

The Plum prototype should be here the 15th of June so stay tuned!
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: AKiwi92 on Sun, 13 June 2021, 16:24:10
This thing is insane. Will vendors be selling extras? Love the thick bezel on this bad boy
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: Havattack on Mon, 14 June 2021, 11:09:06
Quote from: Rotwitt on Sun, 13 June 2021, 15:06:17
Thanks for the support and kind words everyone! It’s been quite a journey so far and I look forward to announcing the GB date (the GB will be some time late July if you missed it)

The Plum prototype should be here the 15th of June so stay tuned!

The Plum is what i have my eye on!
(You should get one of those fabric pill "shavers" for your felt desk mat, It'll trim all those little ball things off.They have them at walmart. I got one for mine)
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: darthcapn on Tue, 15 June 2021, 15:10:00
I love the way this looks. Super into the big bezels!

Sent from my SM-G988U using Tapatalk

Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: RoyalOak88 on Tue, 15 June 2021, 15:21:08
This looks really really good! It will be difficult to chose a color 
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: Rotwitt on Wed, 16 June 2021, 15:28:20
Quote from: Havattack on Mon, 14 June 2021, 11:09:06
Quote from: Rotwitt on Sun, 13 June 2021, 15:06:17
Thanks for the support and kind words everyone! It’s been quite a journey so far and I look forward to announcing the GB date (the GB will be some time late July if you missed it)

The Plum prototype should be here the 15th of June so stay tuned!

The Plum is what i have my eye on!
(You should get one of those fabric pill "shavers" for your felt desk mat, It'll trim all those little ball things off.They have them at walmart. I got one for mine)

I think you're in for a real treat if you're eyeing out the plum! The colour fits the board really well IMO. Tell me what you think

Thanks for the tip on the pill shaver, will try it out!
Title: Re: [IC] POLYGON 65% - MAJOR update 06-07-2021 - Proto 2 pics, website, pricing
Post by: Rotwitt on Wed, 16 June 2021, 15:32:42
Quote from: AKiwi92 on Sun, 13 June 2021, 16:24:10
This thing is insane. Will vendors be selling extras? Love the thick bezel on this bad boy

Thanks!