Author Topic: Would SP ever consider POM (Delrin) plastic material?  (Read 4482 times)

0 Members and 1 Guest are viewing this topic.

Offline dante

  • Thread Starter
  • Posts: 2553
Would SP ever consider POM (Delrin) plastic material?
« on: Fri, 10 October 2014, 14:01:10 »
You already stock POM sets from Cherry.  I'm curious if you could produce some keycap sets with this POM/Delrin plastic - even if they were only blank (I'm not sure if doubleshot POM is even possible)?  DCS would be fine - but SA would also be outstanding.  :eek:
« Last Edit: Fri, 10 October 2014, 17:46:34 by dante »

Offline tbc

  • Posts: 2365
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #1 on: Sat, 11 October 2014, 18:11:55 »
in for blank black dsa
ALL zombros wanted:  dead or undead or dead-dead.

Offline dante

  • Thread Starter
  • Posts: 2553
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #2 on: Wed, 22 October 2014, 11:57:34 »
bump

Offline 00zeRO

  • mechanicalkeyboards.com
  • * Commercial Vendor
  • Posts: 2371
  • Location: Tennessee
  • The 00verseer of Vault 77
    • Mechanical Keyboards
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #3 on: Wed, 22 October 2014, 12:01:30 »
bump

Their silence is deafening...maybe they are too busy counting the dollars from the latest GB, lol.



:p
Daily Driver: Typist A w/Midnight Dawn | Kailh BOX Clicks

          
Junktown 2: Now on eBay!

Offline dante

  • Thread Starter
  • Posts: 2553
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #4 on: Sat, 08 November 2014, 14:45:31 »
bump

Offline 00zeRO

  • mechanicalkeyboards.com
  • * Commercial Vendor
  • Posts: 2371
  • Location: Tennessee
  • The 00verseer of Vault 77
    • Mechanical Keyboards
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #5 on: Sat, 08 November 2014, 14:48:31 »
Daily Driver: Typist A w/Midnight Dawn | Kailh BOX Clicks

          
Junktown 2: Now on eBay!

Offline dante

  • Thread Starter
  • Posts: 2553
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #6 on: Sat, 08 November 2014, 14:52:42 »
No response!

Offline jacobolus

  • Posts: 3661
  • Location: San Francisco, CA
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #7 on: Sat, 08 November 2014, 15:18:19 »
Keep in mind, Melissa, their main contact with the outside world, just had a baby a couple weeks ago.

Offline 00zeRO

  • mechanicalkeyboards.com
  • * Commercial Vendor
  • Posts: 2371
  • Location: Tennessee
  • The 00verseer of Vault 77
    • Mechanical Keyboards
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #8 on: Sat, 08 November 2014, 15:40:38 »
No response!

Be patient, Melissa is out on extended leave. Bob is slowly handling the emails.
Daily Driver: Typist A w/Midnight Dawn | Kailh BOX Clicks

          
Junktown 2: Now on eBay!

Offline Data

  • Posts: 2608
  • Location: Orlando, FL
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #9 on: Mon, 10 November 2014, 15:47:38 »
Bob is doing a fine job, in my limited experience.

Offline 00zeRO

  • mechanicalkeyboards.com
  • * Commercial Vendor
  • Posts: 2371
  • Location: Tennessee
  • The 00verseer of Vault 77
    • Mechanical Keyboards
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #10 on: Mon, 10 November 2014, 16:25:07 »
Bob is doing a fine job, in my limited experience.

I am not picking on him...it just seems to be slower in getting responses now that Melissa is away
Daily Driver: Typist A w/Midnight Dawn | Kailh BOX Clicks

          
Junktown 2: Now on eBay!

Offline SPLady

  • * Moderator
  • Posts: 1
  • Location: Custer, WA
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #11 on: Mon, 10 November 2014, 20:28:03 »
Sorry for the delay! Unfortunately POM (Acetal) has too much shrink to run in our ABS tooling - the result would be unacceptable cosmetic parts - sorry!

Offline dante

  • Thread Starter
  • Posts: 2553
Re: Would SP ever consider POM (Delrin) plastic material?
« Reply #12 on: Mon, 10 November 2014, 20:30:15 »
Sorry for the delay! Unfortunately POM (Acetal) has too much shrink to run in our ABS tooling - the result would be unacceptable cosmetic parts - sorry!

No problem. Thanks for the reply!