Post by: Jaxxstatic on Wed, 22 May 2019, 02:23:13
This is the group buy page for the polycarbonate version of the Rukia, an Alice form factor keyboard with a plastic case.
The first iteration will be in polycarbonate with a brass bottom weight.
The case and plate are compatible with the original Alice. The USB cutout supports both USB-mini and USB-C.
The group buy is limited to 50 total boards for the purpose of a high quality and a relatively fast turnaround to the buyers (90 days projected).
Half the slots are available to FCFS.
Check the interest check thread for more details: https://geekhack.org/index.php?topic=100216.0 (https://geekhack.org/index.php?topic=100216.0)
Supported layouts:
ANSI
Split backspace
Split right shift
1u/1.25u left thumb modifier
stepped/non-stepped caps lock
Plates:
Done by OneFiveNine (159) of Projectkeyboard.com
Either carbon fiber or polycarbonate
A mini group buy will be run for brass and/or Alps-compatible plates based on GB participant preference.
PCB:
Designed by Upas of Cannonkeys.com from Yuktsi's open-source layout
Arm processor
USB-C
Can be programmed with QMK.
Full LED support.
RGB underglow is pre-soldered.
Cost:
$390 for the kit, which includes case, PCB, plate, PVD brass weight, screws, and bump-ons.
Shipping invoices will be sent out after final QC is completed and kits are ready to ship. Each buyer can choose their preferred method of shipment.
90 days
The link below will open at the following time on Thursday 5/23/2019:
9:00 pm US Pacific Daylight Savings Time
International time conversion:
Friday 12:00 am US East Coast
Friday 12:00 pm Singapore/Beijing/Hong Kong
Friday 1:00 pm Japan/Korea/Philippines
Friday 2:00 pm Australia
Friday 5:00 am UK
Friday 6:00 am Germany/Netherlands
Friday 10:00 am India
Group buy link:
https://forms.gle/dv4Xcd3Ftj5wVHmQ7 (https://forms.gle/dv4Xcd3Ftj5wVHmQ7)
3D-printed prototype courtesy of Keyboardbelle:
[attach=4]
[attach=5][attach=6]
Post by: Jaxxstatic on Wed, 22 May 2019, 02:29:58
Post by: victorpre on Wed, 22 May 2019, 13:29:44
Sent from my Pixel 2 XL using Tapatalk
Post by: raphaelf on Wed, 22 May 2019, 13:35:29
Post by: haingo1094 on Wed, 22 May 2019, 13:38:34
Post by: hayt on Wed, 22 May 2019, 13:39:17
Post by: demonahz on Wed, 22 May 2019, 13:40:34
Post by: pnkpanther65 on Wed, 22 May 2019, 13:43:14
Post by: Create_alt_delete on Wed, 22 May 2019, 13:43:50
Sent from my SM-G955U using Tapatalk
Post by: te_dulce on Wed, 22 May 2019, 13:46:17
I hope these last longer than 2 secondsI hope there's another round of polycarb
Sent from my SM-G955U using Tapatalk
Sent from my Mi A1 using Tapatalk
Post by: jaang on Wed, 22 May 2019, 13:46:57
Post by: KingOfMemes on Wed, 22 May 2019, 13:52:00
Post by: lolafineday on Wed, 22 May 2019, 13:53:30
Sent from my SM-G975F using Tapatalk
Post by: Esheu2 on Wed, 22 May 2019, 13:53:55
Post by: t0ch on Wed, 22 May 2019, 13:59:13
Post by: Jaxxstatic on Wed, 22 May 2019, 14:02:17
I believe that PDT is being observed right now, rather than PST.Oh I mean current California time. Adjusted thank you. It’s PDT now. I think the conversions still work though. Please verify for yourself. Thank you!
Post by: iaman on Wed, 22 May 2019, 14:05:49
This ain't a judgment on you, but I feel like we should just set a rule in this board that times should be communicated in GMT (or some other arbitrary time zone) just for clarity's sakeI believe that PDT is being observed right now, rather than PST.Oh I mean California time.
(for the record I think you've been doing a fantastic job running your ICs and this GB so far, keep up the great work)
Post by: KingOfMemes on Wed, 22 May 2019, 14:08:33
PCB:Just out of curiosity, is there a qmk layout lurking around for this already?
Designed by Upas of Cannonkeys.com from Yuktsi's open-source layout
Arm processor
USB-C
Can be programmed with QMK.
Full LED support.
RGB backlighting is pre-soldered.
Post by: iaman on Wed, 22 May 2019, 14:14:22
I believe it's this one (https://github.com/qmk/qmk_firmware/tree/master/keyboards/projectkb/alice), based on the active work over here (https://github.com/awkannan/qmk_firmware/tree/201904_project_alice)PCB:Just out of curiosity, is there a qmk layout lurking around for this already?
Designed by Upas of Cannonkeys.com from Yuktsi's open-source layout
Arm processor
USB-C
Can be programmed with QMK.
Full LED support.
RGB backlighting is pre-soldered.
Post by: KingOfMemes on Wed, 22 May 2019, 14:14:56
Bless up fam, trust.I believe it's this one (https://github.com/qmk/qmk_firmware/tree/master/keyboards/projectkb/alice), based on the active work over here (https://github.com/awkannan/qmk_firmware/tree/201904_project_alice)PCB:Just out of curiosity, is there a qmk layout lurking around for this already?
Designed by Upas of Cannonkeys.com from Yuktsi's open-source layout
Arm processor
USB-C
Can be programmed with QMK.
Full LED support.
RGB backlighting is pre-soldered.
Post by: g_mr_p on Wed, 22 May 2019, 14:22:42
Post by: Aznguyen316 on Wed, 22 May 2019, 14:23:14
Post by: Villa on Wed, 22 May 2019, 14:28:56
Alright. Gotta support the man.
Post by: Jaxxstatic on Wed, 22 May 2019, 15:04:53
Post by: ArchDill on Wed, 22 May 2019, 15:32:14
Post by: krazysamurai on Wed, 22 May 2019, 15:39:04
Post by: pnkpanther65 on Wed, 22 May 2019, 15:57:24
Post by: Jaxxstatic on Wed, 22 May 2019, 16:21:43
Is the PVD brass weight gonna be the same size, shape, and placement as the Alice?No it should be just a little bit longer. Also it screws in from the inside of the case.
Post by: lolafineday on Wed, 22 May 2019, 16:24:31
Sent from my SM-G975F using Tapatalk
Post by: andrewregal on Wed, 22 May 2019, 16:26:59
Post by: AlcoholEnthusiast on Wed, 22 May 2019, 16:37:46
Post by: aeryxz on Wed, 22 May 2019, 16:43:42
Post by: zap2oz on Wed, 22 May 2019, 18:09:21
Post by: wd9001 on Wed, 22 May 2019, 18:23:27
Sent from my SM-N950F using Tapatalk
Post by: fishinaspacesuit on Wed, 22 May 2019, 18:29:55
Post by: briano1905 on Wed, 22 May 2019, 18:51:20
https://www.timeanddate.com/countdown/generic?p0=137&iso=20190523T21&year=2019&month=5&day=23&hour=21&min=0&sec=0&msg=Rukia%20form
Post by: lakeboredom on Wed, 22 May 2019, 19:13:17
Post by: Esheu2 on Wed, 22 May 2019, 19:15:38
The proto is printed right? Just checking, will the final product be solid pc? Probably a stupid question.yes
Post by: Allo on Wed, 22 May 2019, 19:48:11
Post by: TheMnBN on Wed, 22 May 2019, 20:01:57
Post by: Esheu2 on Wed, 22 May 2019, 20:11:31
50 spots. Gotta go fast!Half of them are already claimed by the private slots. So, there are really only 25 fcfs spots up for grabs.
Post by: Furikurichemy on Wed, 22 May 2019, 20:15:42
Post by: heycheeeno on Wed, 22 May 2019, 20:51:49
As I already have a plate and PCB
Post by: dantambok on Wed, 22 May 2019, 21:11:04
Post by: blizzara01 on Wed, 22 May 2019, 21:19:19
g'luck ya'llHey! You have already Rukia in your sig LOL :))
Post by: reidd on Wed, 22 May 2019, 22:51:38
Post by: pcire on Wed, 22 May 2019, 23:18:38
The timing isn’t right for me, but i hope everything goes well!
Post by: dantambok on Wed, 22 May 2019, 23:20:40
g'luck ya'llHey! You have already Rukia in your sig LOL :))
Whoops it just snuck in there haha
Post by: wcmbk on Wed, 22 May 2019, 23:58:30
Post by: skmn on Thu, 23 May 2019, 00:03:49
Post by: lanyusea on Thu, 23 May 2019, 00:39:37
nice work, and still look forward to the UHMW version
Post by: demonahz on Thu, 23 May 2019, 05:03:29
I was hoping I could jump in on this one, but I don't think the odds are in my favor. GL.
I will wake up at 5:30am most likely just to feel bad and mad for not making it :(
Post by: genesisx on Thu, 23 May 2019, 07:04:22
Post by: vtachkov on Thu, 23 May 2019, 16:03:47
Post by: crystalflame on Thu, 23 May 2019, 17:37:30
Post by: Jaxxstatic on Thu, 23 May 2019, 22:46:32
Let's hope this works...
I'll take orders for extra PCBs and plates after the GB entrants are determined.
I'll be posting updates here in this thread regularly.
Post by: jaang on Thu, 23 May 2019, 23:01:09
edit: looks like it just opened a tad late.
Post by: rossfromfriends on Thu, 23 May 2019, 23:01:27
Post by: Jaxxstatic on Thu, 23 May 2019, 23:01:46
Post by: andrewregal on Thu, 23 May 2019, 23:02:00
Post by: Slash Emperor on Thu, 23 May 2019, 23:02:06
Post by: ItsAllen on Thu, 23 May 2019, 23:02:09
Post by: Petch on Thu, 23 May 2019, 23:02:18
Post by: AlcoholEnthusiast on Thu, 23 May 2019, 23:02:27
Post by: loud_asian on Thu, 23 May 2019, 23:02:34
Post by: freespam on Thu, 23 May 2019, 23:02:37
Post by: Furikurichemy on Thu, 23 May 2019, 23:02:44
Post by: MightyFineShindig on Thu, 23 May 2019, 23:02:50
Post by: vtachkov on Thu, 23 May 2019, 23:02:55
Post by: crystalflame on Thu, 23 May 2019, 23:03:02
Post by: cari on Thu, 23 May 2019, 23:03:08
Post by: wcmbk on Thu, 23 May 2019, 23:03:14
Post by: holtenc on Thu, 23 May 2019, 23:03:19
Post by: ian13 on Thu, 23 May 2019, 23:03:23
Post by: Esheu2 on Thu, 23 May 2019, 23:03:24
Post by: Lormania on Thu, 23 May 2019, 23:03:28
Post by: jaang on Thu, 23 May 2019, 23:03:32
well, got my form submitted and crossing my fingers! good luck everyone!
Same here, end screen says I'm in, so hope it works out!
Post by: vegs on Thu, 23 May 2019, 23:03:36
Post by: lanyusea on Thu, 23 May 2019, 23:03:41
Post by: Jaxxstatic on Thu, 23 May 2019, 23:03:45
7 extra submissions got in. I'll honor all that the form let in.
give me a few moments to figure this out please
Post by: wcmbk on Thu, 23 May 2019, 23:03:48
Wasn't able to get in but what's with the two email address?That’s what threw me, wasted like 5 seconds trying to figure that out
Post by: raphaelf on Thu, 23 May 2019, 23:03:50
Post by: ian13 on Thu, 23 May 2019, 23:04:07
The form didn't open until after 12:01 and it said it wasn't taking any more responses as soon as I had it filled out? Was everyone elses experiences the same?
Same
Post by: Slash Emperor on Thu, 23 May 2019, 23:04:11
Damn, filled everything and it was closed when I sent. =/
Same, man.
Post by: BSGalaxy on Thu, 23 May 2019, 23:04:28
Post by: freespam on Thu, 23 May 2019, 23:04:33
well, got my form submitted and crossing my fingers! good luck everyone!
Same here, end screen says I'm in, so hope it works out!
uh oh...after I submitted I got this...yours said you're in?
"Rukia Keyboard Group Buy
This form is no longer accepting responses, and has been set to automatically close by Jaxxstatic."
Post by: Furikurichemy on Thu, 23 May 2019, 23:05:00
Post by: jaang on Thu, 23 May 2019, 23:05:05
well, got my form submitted and crossing my fingers! good luck everyone!
Same here, end screen says I'm in, so hope it works out!
uh oh...after I submitted I got this...yours said you're in?
"Rukia Keyboard Group Buy
This form is no longer accepting responses, and has been set to automatically close by Jaxxstatic."
Yeah, mine says the following "Rukia Keyboard Group Buy
Congratulations! You have made it into the Group Buy. "
Post by: freespam on Thu, 23 May 2019, 23:05:19
screw that google add on.
7 extra submissions got in. I'll honor all that the form let in.
give me a few moments to figure this out please
oh yaaaaaaaaaaaaas
Post by: TheMnBN on Thu, 23 May 2019, 23:05:26
The form didn't open until after 12:01 and it said it wasn't taking any more responses as soon as I had it filled out? Was everyone elses experiences the same?
Same
Same here :confused:
Post by: andrewregal on Thu, 23 May 2019, 23:05:38
Post by: ian13 on Thu, 23 May 2019, 23:05:59
At least this means I can save money for the UHMW version :raughs:
Hopefully, it will not be too limited for the UHMW like this. RIP for us who couldn't enter..
Post by: wd9001 on Thu, 23 May 2019, 23:06:23
Post by: skmn on Thu, 23 May 2019, 23:06:34
Post by: demonahz on Thu, 23 May 2019, 23:06:39
sad :(
Post by: onlinegamer0 on Thu, 23 May 2019, 23:06:43
Damn, filled everything and it was closed when I sent. =/
Same, man.
Same... not quite fast enough, took an L
Post by: AlcoholEnthusiast on Thu, 23 May 2019, 23:07:38
Post by: jhmoon999 on Thu, 23 May 2019, 23:08:03
Signed in and submitted the form but it was too late.
Will remember for the next one.
Post by: Jaxxstatic on Thu, 23 May 2019, 23:08:06
Everyone has 24 hours to pay.
Post by: AlcoholEnthusiast on Thu, 23 May 2019, 23:08:48
Is there any chance at a larger production R2 for this? I was literally refreshing until it opened and typed as fast as I could and still couldn't get in
Yeah that was my experience too. Usually I'm quick enough for stuff like this. RIP
Post by: wcmbk on Thu, 23 May 2019, 23:09:03
Invoices going out in a few minutes.
Everyone has 24 hours to pay.
Any re-raf for unpaids?
Post by: funderburker on Thu, 23 May 2019, 23:09:22
Post by: darrenph1 on Thu, 23 May 2019, 23:09:48
At least this means I can save money for the UHMW version :raughs:This! :thumb:
Post by: radam on Thu, 23 May 2019, 23:10:13
Post by: Jaxxstatic on Thu, 23 May 2019, 23:11:25
Yes.Invoices going out in a few minutes.
Everyone has 24 hours to pay.
Any re-raf for unpaids?
If you didn't get in, ping me on discord with your email and plate preference.
That's not a guarantee that you'll get a spot. I'm going to respond with a number. That's your raffle number if there are unpaid invoices.
Post by: dantambok on Thu, 23 May 2019, 23:13:28
Post by: Furikurichemy on Thu, 23 May 2019, 23:14:36
Post by: Zurg Eon on Thu, 23 May 2019, 23:16:08
Post by: freespam on Thu, 23 May 2019, 23:25:06
well, got my form submitted and crossing my fingers! good luck everyone!
Same here, end screen says I'm in, so hope it works out!
uh oh...after I submitted I got this...yours said you're in?
"Rukia Keyboard Group Buy
This form is no longer accepting responses, and has been set to automatically close by Jaxxstatic."
Yeah, mine says the following "Rukia Keyboard Group Buy
Congratulations! You have made it into the Group Buy. "
oh crap I got my hopes up and now the disappointment is setting in :( well congrats to those that made it
Post by: Jaxxstatic on Thu, 23 May 2019, 23:25:32
SO please ping me on Discord at jaxxstatic#2116.
I've been giving out raffle numbers for if people don't pay invoices. Pin your email and plate preference please.
Post by: Esheu2 on Thu, 23 May 2019, 23:31:53
Post by: reidd on Thu, 23 May 2019, 23:32:22
Yeah this and the Keycult no2. My two failures :(
Yeah bro same here. :(
Post by: jaang on Thu, 23 May 2019, 23:33:03
Invoices going out in a few minutes.
Everyone has 24 hours to pay.
Have all the invoices been sent out?
Post by: vtachkov on Thu, 23 May 2019, 23:45:59
Post by: Cybee on Thu, 23 May 2019, 23:50:48
Post by: Jaxxstatic on Thu, 23 May 2019, 23:51:57
I'm just making the initial buy as simple as possible, in case people don't pay or change their mind.
BTW I put "email" twice in the form because I've messed up on inputting my email in artisan raffles and felt so bad afterward.
Post by: Esheu2 on Thu, 23 May 2019, 23:54:05
Post by: briano1905 on Thu, 23 May 2019, 23:55:00
Just got my invoice.
same
Post by: Jaxxstatic on Fri, 24 May 2019, 00:00:47
Just paid mine! The description says PC plate, but I'm pretty sure I picked CF?your form says "polycarbonate plate" but please pm me on Discord
Post by: jhmoon999 on Fri, 24 May 2019, 00:52:03
Post by: vegs on Fri, 24 May 2019, 00:59:07
Post by: Esheu2 on Fri, 24 May 2019, 01:21:22
New to Discord. How do you message a non-friend on Discord? Or is there a central discord for Geekhack users?
When you're on your homepage, there should be a search bar thing on the top left near the discord icon. It will say "Find or start a conversation". Simply input the user ID of the person you would like to message.
Post by: Jaxxstatic on Fri, 24 May 2019, 19:38:44
So I'm giving everyone else time too. Pay period extended 12 hours, so raffle will be held at 10:00 am California time tomorrow if there are unpaid invoices.
Everyone who contacted me was given a raffle number on Discord.
오렌지말고 알.엔.지.
Post by: wcmbk on Fri, 24 May 2019, 19:40:00
I need to time to compile and organize.
So I'm giving everyone else time too. Pay period extended 12 hours, so raffle will be held at 10:00 am California time tomorrow if there are unpaid invoices.
Everyone who contacted me was given a raffle number on Discord.
오렌지말고 알.엔.지.
Hey mate, I sent you a message on Discord! (Blinky)
Post by: pnkpanther65 on Fri, 24 May 2019, 19:41:51
Sent from my Pixel 2 using Tapatalk
Post by: Villa on Fri, 24 May 2019, 20:00:04
Pay period extended 12 hours, so raffle will be held at 10:00 am California time tomorrow if there are unpaid invoices.
Everyone who contacted me was given a raffle number on Discord.
오렌지말고 알.엔.지.
Does this mean that there will be a chance for those who missed the raffle, like myself, to join?
Post by: Lormania on Fri, 24 May 2019, 20:24:49
Post by: AlcoholEnthusiast on Sat, 25 May 2019, 12:18:56
Post by: Jaxxstatic on Sat, 25 May 2019, 12:27:39
For everyone interested in following this project on Discord, I made a server here: https://discord.gg/zz3GkM (https://discord.gg/zz3GkM)
But I don’t like keeping updates in Discord because they can get lost in chat, and even pinned messages get missed. Forum format is kind of easier to follow as a timeline, so if I post updates in the Discord server it will likely also get posted here.
Picture uploads are just easier from my phone on Discord.
Post by: andrewregal on Sat, 25 May 2019, 13:16:00
Post by: vegs on Mon, 27 May 2019, 00:28:31
Waiting on a couple people with extenuating circumstances, but it looks like all invoices will be paid today.Looks like the invite is dead
For everyone interested in following this project on Discord, I made a server here: https://discord.gg/zz3GkM (https://discord.gg/zz3GkM)
But I don’t like keeping updates in Discord because they can get lost in chat, and even pinned messages get missed. Forum format is kind of easier to follow as a timeline, so if I post updates in the Discord server it will likely also get posted here.
Picture uploads are just easier from my phone on Discord.
Post by: Jaxxstatic on Mon, 27 May 2019, 01:17:26
Post by: KingOfMemes on Wed, 29 May 2019, 09:18:03
Post by: Jaxxstatic on Wed, 29 May 2019, 11:08:14
Anyone have any ideas for a wrist rest for this thing?A couple of the GB participants actually make really really awesome ones. And have for Alice as well. So expect that Rukia will have some support options too
Post by: yur1orlov on Wed, 29 May 2019, 19:43:45
Post by: fanovorc on Wed, 29 May 2019, 22:43:08
Post by: Jaxxstatic on Wed, 29 May 2019, 23:27:11
may i have ONLY a rukia pcb？or get the open source files，or tell me where HOW i get them.I hope our conversation on Discord was a case of “lost in translation,” and not a case of you insulting me while asking me for something.
The files are open source here on geekhack, posted by Yuktsi himself.
There are other options that already exist, including the Lubrigante, projectkeyboard, and others.
I am also still working on another project in this form factor that you might have liked if I didn’t ban you for what I took to be an insult. The project will not be in such small numbers but will still maintain high quality standards.
I’ll post details in an IC thread in this coming week about that particular project. Please wait til then.
I appreciate everyone’s support for this project. My interactions with most have been pleasant and cordial.
As some are already aware, I had an unexpected death in the family. I’m still waiting on details and may take longer to respond than normal the next few days. But I will get to you with answers if you hit me up. Response just might be delayed.
Please rest assured that this is not me saying I’m dipping out or even taking a break from anything. I’m still around. I’m still reachable. I’ll still give updates on this and other projects.
Post by: fanovorc on Thu, 30 May 2019, 00:13:06
may i have ONLY a rukia pcb？or get the open source files，or tell me where HOW i get them.I hope our conversation on Discord was a case of “lost in translation,” and not a case of you insulting me while asking me for something.
The files are open source here on geekhack, posted by Yuktsi himself.
There are other options that already exist, including the Lubrigante, projectkeyboard, and others.
I am also still working on another project in this form factor that you might have liked if I didn’t ban you for what I took to be an insult. The project will not be in such small numbers but will still maintain high quality standards.
I’ll post details in an IC thread in this coming week about that particular project. Please wait til then.
I appreciate everyone’s support for this project. My interactions with most have been pleasant and cordial.
As some are already aware, I had an unexpected death in the family. I’m still waiting on details and may take longer to respond than normal the next few days. But I will get to you with answers if you hit me up. Response just might be delayed.
Please rest assured that this is not me saying I’m dipping out or even taking a break from anything. I’m still around. I’m still reachable. I’ll still give updates on this and other projects.
I must apologize for my poor English，i am not a native speaker, may be i misuse some words that is not my real thought.
Post by: funderburker on Thu, 30 May 2019, 02:14:00
may i have ONLY a rukia pcb？or get the open source files，or tell me where HOW i get them.I hope our conversation on Discord was a case of “lost in translation,” and not a case of you insulting me while asking me for something.
The files are open source here on geekhack, posted by Yuktsi himself.
There are other options that already exist, including the Lubrigante, projectkeyboard, and others.
I am also still working on another project in this form factor that you might have liked if I didn’t ban you for what I took to be an insult. The project will not be in such small numbers but will still maintain high quality standards.
I’ll post details in an IC thread in this coming week about that particular project. Please wait til then.
I appreciate everyone’s support for this project. My interactions with most have been pleasant and cordial.
As some are already aware, I had an unexpected death in the family. I’m still waiting on details and may take longer to respond than normal the next few days. But I will get to you with answers if you hit me up. Response just might be delayed.
Please rest assured that this is not me saying I’m dipping out or even taking a break from anything. I’m still around. I’m still reachable. I’ll still give updates on this and other projects.
Sad to hear about your family. :(
Post by: KingOfMemes on Thu, 30 May 2019, 08:24:18
You have been super transparent and active about this whole project in GH and in Discord, fam. Everyone involved appreciates it. :thumb:may i have ONLY a rukia pcb？or get the open source files，or tell me where HOW i get them.I hope our conversation on Discord was a case of “lost in translation,” and not a case of you insulting me while asking me for something.
The files are open source here on geekhack, posted by Yuktsi himself.
There are other options that already exist, including the Lubrigante, projectkeyboard, and others.
I am also still working on another project in this form factor that you might have liked if I didn’t ban you for what I took to be an insult. The project will not be in such small numbers but will still maintain high quality standards.
I’ll post details in an IC thread in this coming week about that particular project. Please wait til then.
I appreciate everyone’s support for this project. My interactions with most have been pleasant and cordial.
As some are already aware, I had an unexpected death in the family. I’m still waiting on details and may take longer to respond than normal the next few days. But I will get to you with answers if you hit me up. Response just might be delayed.
Please rest assured that this is not me saying I’m dipping out or even taking a break from anything. I’m still around. I’m still reachable. I’ll still give updates on this and other projects.
Post by: Jaxxstatic on Tue, 09 July 2019, 22:11:32
Link should be set to never expire and unlimited shares.
Other projects are also in the Discord.
Updates:
-Manufacturer paid.
-Notches added to align the top and bottom parts of the case.
-USB-mini only, so that it's still compatible with Alice PCBs and builds. Just drop in.
Post by: ReDsNoTDeAd on Fri, 12 July 2019, 10:24:26
Post by: dantambok on Fri, 12 July 2019, 10:36:15
Are you open sourcing the plates for this, or will are OG alice plates compatible?
OG alice plate will fit.
Post by: ReDsNoTDeAd on Fri, 12 July 2019, 10:37:23
A
L
A
M
A
T
Post by: KingOfMemes on Fri, 12 July 2019, 16:54:47
https://discord.gg/eJrjdtg (https://discord.gg/eJrjdtg)This is excellent news. Glad things are moving smoothly. Thanks for posting major updates in this thread. Us non-discord users appreciate it :-* :thumb:
Link should be set to never expire and unlimited shares.
Other projects are also in the Discord.
Updates:
-Manufacturer paid.
-Notches added to align the top and bottom parts of the case.
-USB-mini only, so that it's still compatible with Alice PCBs and builds. Just drop in.
Post by: Curia on Fri, 12 July 2019, 22:53:53
Post by: lolafineday on Sat, 13 July 2019, 01:08:15
Any chance a second round of cases will be run after the first lot are completed?There will be the uhmw alice, which imo is a greater material for keyboards than polycarbonate which is set to run after this preliminary batch of pc Alice's are out, around early september.
Sent from my SM-G975F using Tapatalk
Post by: Jaxxstatic on Wed, 07 August 2019, 18:45:09
PCBs are in hand and tested. Look good.
[attach=1]
[attach=2]
[attach=3]
[attach=4]
Cases are getting there. Waiting on sandblasting. More pics in the Discord:
[attach=5]
[attach=6]
Brass plate GB form open. I'll close it Thursday at 10pm California time.
https://forms.gle/1GxpuN3MNG3P25fs7 (https://forms.gle/1GxpuN3MNG3P25fs7)
Post by: KingOfMemes on Wed, 07 August 2019, 19:24:28
Post by: vegs on Thu, 08 August 2019, 03:02:54
Post by: monkeycap198 on Thu, 08 August 2019, 08:27:16
Post by: yur1orlov on Thu, 08 August 2019, 10:13:27
Post by: CypherPls on Wed, 28 August 2019, 15:09:34
Post by: AlcoholEnthusiast on Wed, 28 August 2019, 23:38:46
I'm curious, are these being shipped yet? And Is there any spots avail if not?
These have not been shipped. There are no extra spots, the group buy filled up a few months ago.
Post by: Jaxxstatic on Thu, 29 August 2019, 00:12:48
I'm curious, are these being shipped yet? And Is there any spots avail if not?
These are scheduled to ship in September. I will do my best to stay true to that. Extras may be available after GB-participants get their boards. The priority will be to replace any defective cases with A-stock from the extras, so participants don't have to wait.
Post by: Jaxxstatic on Thu, 29 August 2019, 00:13:48
I've been in a really weird place with work for a bit now. I've been up for promotion at work, working extra, and trying to make things livable, but today I finally got word:
I got the promotion, but the salary offer is.... not enough to really live on. I honestly thought it would be worth it to continue this job and do the keyboard business at the same time, but it really doesn't make sense to stay in a job that takes up so much of my time, is physically and emotionally exhausting, and inhibits from realizing my real passion and what I know I can accomplish.
What makes sense to me is to just go full-bore with keyboards.
What does this mean for you guys? What is my projected timeline?
Well, here it is so far....
I'll be speeding up the timeline on all current and upcoming projects.
Rukia will ship in September.
October will be a month-long campaign to get the final funds for manufacturing equipment.
By November, I'll be manufacturing Irma and two other boards--a 65% and a 75%--all in UHMW.
Those boards and all future boards will be available on my website on a made-to-order basis.
That means by December, before 2020, UHMW will be a reality in the community in regards to cases.
2020 will be the year of indestructible cases and lube-less switches.
Post by: dexie on Thu, 29 August 2019, 00:25:28
Ok, so...this is what I put up on Discord just now...
I've been in a really weird place with work for a bit now. I've been up for promotion at work, working extra, and trying to make things livable, but today I finally got word:
I got the promotion, but the salary offer is.... not enough to really live on. I honestly thought it would be worth it to continue this job and do the keyboard business at the same time, but it really doesn't make sense to stay in a job that takes up so much of my time, is physically and emotionally exhausting, and inhibits from realizing my real passion and what I know I can accomplish.
What makes sense to me is to just go full-bore with keyboards.
What does this mean for you guys? What is my projected timeline?
Well, here it is so far....
I'll be speeding up the timeline on all current and upcoming projects.
Rukia will ship in September.
October will be a month-long campaign to get the final funds for manufacturing equipment.
By November, I'll be manufacturing Irma and two other boards--a 65% and a 75%--all in UHMW.
Those boards and all future boards will be available on my website on a made-to-order basis.
That means by December, before 2020, UHMW will be a reality in the community in regards to cases.
2020 will be the year of indestructible cases and lube-less switches.
Thank you for your service for this community! I will sure get a board or two.
Post by: KingOfMemes on Thu, 29 August 2019, 08:10:10
Ok, so...this is what I put up on Discord just now...God comment
I've been in a really weird place with work for a bit now. I've been up for promotion at work, working extra, and trying to make things livable, but today I finally got word:
I got the promotion, but the salary offer is.... not enough to really live on. I honestly thought it would be worth it to continue this job and do the keyboard business at the same time, but it really doesn't make sense to stay in a job that takes up so much of my time, is physically and emotionally exhausting, and inhibits from realizing my real passion and what I know I can accomplish.
What makes sense to me is to just go full-bore with keyboards.
What does this mean for you guys? What is my projected timeline?
Well, here it is so far....
I'll be speeding up the timeline on all current and upcoming projects.
Rukia will ship in September.
October will be a month-long campaign to get the final funds for manufacturing equipment.
By November, I'll be manufacturing Irma and two other boards--a 65% and a 75%--all in UHMW.
Those boards and all future boards will be available on my website on a made-to-order basis.
That means by December, before 2020, UHMW will be a reality in the community in regards to cases.
2020 will be the year of indestructible cases and lube-less switches.
Post by: andrewregal on Fri, 30 August 2019, 01:04:48
Post by: KingOfMemes on Fri, 30 August 2019, 08:59:29
Post by: victorpre on Fri, 30 August 2019, 09:07:02
Anybody trying to take some of my money and make a wrist rest for this bad boy?
This
Post by: AlcoholEnthusiast on Fri, 30 August 2019, 17:15:37
Anybody trying to take some of my money and make a wrist rest for this bad boy?
This
Post by: Hadi on Sat, 31 August 2019, 14:09:20
Anybody trying to take some of my money and make a wrist rest for this bad boy?
Are the dimensions and profile of the front bezel publicly available? I have some basic modeling skills and have made wooden wrist wrests for my own Alice-like boards in the past.
Post by: Jaxxstatic on Sat, 14 September 2019, 18:21:21
[attachimg=2]
Still hoping to ship in September. Looks like we are on course. PVD finishing right now.
Post by: KingOfMemes on Sat, 14 September 2019, 19:12:19
(Attachment Link)Dawg.... this **** is fire. I'm so hype for this thing man, killer job with this entire groupbuy
(Attachment Link)
Still hoping to ship in September. Looks like we are on course. PVD finishing right now.
Post by: PikaJoyce on Sat, 14 September 2019, 19:22:38
(Attachment Link)I hope that you re-run the PC Rukia again in the future, really sad that I wasn't able to snag one. Regardless, this looks fantastic :)
(Attachment Link)
Still hoping to ship in September. Looks like we are on course. PVD finishing right now.
Post by: Jaxxstatic on Wed, 18 September 2019, 23:27:48
Here is Rukia with polycarb plate.
[attachimg=1][attachimg=2][attachimg=3]
Post by: AlcoholEnthusiast on Wed, 18 September 2019, 23:44:36
Seriously though, extremely excited about this board. Can't wait to see it in person and build it out.
Post by: KingOfMemes on Thu, 19 September 2019, 08:20:49
Any idea on the shipdate for people who did NOT order brass plates... and are probably regretting not doing so? Either way, you are way in above schedule which is awesome :thumb: this GB has been pretty damn perfect, honestly
Post by: Choobies on Thu, 19 September 2019, 10:25:20
If you would like your brass weight to be sandblasted raw instead of PVD coated, please fill out the form here: https://forms.gle/WQnuahr7hwvVoP5Z7
Post by: lakeboredom on Thu, 19 September 2019, 21:26:50
Post by: wcmbk on Thu, 19 September 2019, 21:32:26
Is this still the thread to watch if I want the plastic Alice? I saw an update that the PC ones will be buyable soon?
This GB ended a few months ago - they’re shipping soon, so you may be able to get one off the aftermarket.
Alternatively, the POM/UHMW Alice should be selling somewhat soon. It’s a different plastic, but I think Jaxx is planning to sell unlimited copies of them.
Post by: Jaxxstatic on Tue, 08 October 2019, 15:55:16
[attachimg=2]
[attachimg=3]
[attachimg=4]
[attachimg=5]
[attachimg=6]
[attachimg=7]
[attachimg=8]
Post by: kconfire on Tue, 08 October 2019, 15:57:11
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
oof
please full send one to me :P
Post by: KingOfMemes on Tue, 08 October 2019, 16:10:05
(Attachment Link)Oh god yes...
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Post by: fireworm on Tue, 08 October 2019, 16:33:05
Post by: KingOfMemes on Tue, 08 October 2019, 17:01:22
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Way the hell off topic, but can I get an id on the cable/cable connector in these photos?
Post by: Mcnos on Tue, 08 October 2019, 18:02:57
Post by: yicaoyimu on Tue, 08 October 2019, 20:20:26
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
(Attachment Link)
Way the hell off topic, but can I get an id on the cable/cable connector in these photos?
Just a normal usb cable with a yarbo shield.
Post by: dankpupdaddy on Tue, 08 October 2019, 22:32:30
Post by: KingOfMemes on Thu, 10 October 2019, 14:20:20
(https://geekhack.org/index.php?action=dlattach;topic=100847.0;attach=227829;image)
Post by: superdoedoe on Thu, 10 October 2019, 14:45:31
Wait, wat dis do?Leds? Tgr Alice USB has little spot for the LEDs there as wellShow Image(https://geekhack.org/index.php?action=dlattach;topic=100847.0;attach=227829;image)
Sent from my SM-G970F using Tapatalk
Post by: KingOfMemes on Thu, 10 October 2019, 14:55:52
Yeet thanksWait, wat dis do?Leds? Tgr Alice USB has little spot for the LEDs there as wellShow Image(https://geekhack.org/index.php?action=dlattach;topic=100847.0;attach=227829;image)
Sent from my SM-G970F using Tapatalk
Post by: Jaxxstatic on Sat, 12 October 2019, 19:55:49
Post by: KingOfMemes on Sat, 12 October 2019, 21:29:14
Yes. Inside of the top case, looking at the LED area. I made the wells as big as possible to accommodate people like myself who only have giant LEDs at their disposal.What LEDs do I need to get for this?
Post by: Mcnos on Sun, 13 October 2019, 08:41:18
Post by: lakeboredom on Thu, 17 October 2019, 04:10:43
Post by: Stvnce on Sat, 19 October 2019, 01:12:02
Post by: sapphyr on Sat, 19 October 2019, 22:46:59
Post by: Esheu2 on Sat, 19 October 2019, 23:50:34
hi - any update on the brass plates and when those will ship? thanks
(https://i.imgur.com/KOmQpiU.png)
Post by: shuangmu on Tue, 22 October 2019, 10:47:57
Post by: Sup on Sat, 14 December 2019, 20:03:36
Post by: lolafineday on Sat, 14 December 2019, 20:23:28
Will there be ever r2 or nah?A alice in the uhmw material will be made soon by the same maker of this board.
Sent from my SM-G975F using Tapatalk
Post by: Jaxxstatic on Sat, 14 December 2019, 21:17:09
Will there be ever r2 or nah?
I've gotten MANY requests for extras or a round 2.
UHMW is the next iteration, hopefully by the end of January.
But even knowing this, some still prefer polycarb.
I have that in mind, however, I haven't run an IC for R2 polycarb Rukia because I haven't yet fully delivered R1 and made sure that buyers from R1 are satisfied.
More important than that is if Yuktsi plans to run polycarb Alice. If so, I won't do another polycarb run at all. I'll be joining the real TGR GB.
If I run a R2 for polycarb it will be a group buy format in January. Lead time from the manufacturer will be 45 days. Delivery from me will be much more streamlined, learning what I did through this first GB.
For UHMW boards, I am about to launch a website for orders. At the end of January, I will have made enough injection molded "blanks" that you can order online and pick out your customization options. Orders will be fulfilled "made to order" this way, and I'm shooting for a turnaround of 1 week or less at first.
Online "in stock" availability will open and closed based on that turnaround. So if the website says "out of stock," I've reached my max capability to meet that timeline.
I'll announce in this thread and on Discord when the site is ready to launch and how many boards will be available for the first group of orders to test out how many I can turn out in a week.
Post by: Sup on Sun, 15 December 2019, 07:51:18
Will there be ever r2 or nah?
I've gotten MANY requests for extras or a round 2.
UHMW is the next iteration, hopefully by the end of January.
But even knowing this, some still prefer polycarb.
I have that in mind, however, I haven't run an IC for R2 polycarb Rukia because I haven't yet fully delivered R1 and made sure that buyers from R1 are satisfied.
More important than that is if Yuktsi plans to run polycarb Alice. If so, I won't do another polycarb run at all. I'll be joining the real TGR GB.
If I run a R2 for polycarb it will be a group buy format in January. Lead time from the manufacturer will be 45 days. Delivery from me will be much more streamlined, learning what I did through this first GB.
For UHMW boards, I am about to launch a website for orders. At the end of January, I will have made enough injection molded "blanks" that you can order online and pick out your customization options. Orders will be fulfilled "made to order" this way, and I'm shooting for a turnaround of 1 week or less at first.
Online "in stock" availability will open and closed based on that turnaround. So if the website says "out of stock," I've reached my max capability to meet that timeline.
I'll announce in this thread and on Discord when the site is ready to launch and how many boards will be available for the first group of orders to test out how many I can turn out in a week.
Oh didn't expect a R2 to be this soon awesome. In my opinion you don't need to cancel the poly carbonate version if yutski runs Alice R2 poly carbonate because the demand will be so high that like probably 1/50 will probably get a GB spot. So having two options for more chance to get a poly carbonate Alice would be nice.
Also is there a discord link to join the discord server?
Edit: Found it nvm
Post by: upintheclouds on Sun, 15 December 2019, 22:43:36
Post by: zian_ on Tue, 17 December 2019, 14:01:21
Post by: Sup on Tue, 17 December 2019, 15:14:16
I'm guessing I already know the answer, but were there any extras?
you know what it is brother :'(. But no worries R2 is gonna be somewhere end January :)
Post by: thnick on Fri, 20 December 2019, 09:07:15
you know what it is brother :'(. But no worries R2 is gonna be somewhere end January :)
Can't hardly wait. :p
Post by: lakeboredom on Mon, 23 December 2019, 00:00:04
For Rukia R2, is it possible to offer alternate colors of PC for the case? Even a simple black might be nice for a choice, but translucent blue or purple would work super well for gmk vaporwave imo, and I'd personally pay extra for that.Colored polycarb would be tits!
Post by: helborne on Thu, 26 December 2019, 21:26:40
Post by: d4vid4f on Mon, 30 December 2019, 11:21:10
Post by: whyamihere on Mon, 30 December 2019, 13:55:53
Post by: Jaxxstatic on Tue, 31 December 2019, 17:26:30
A surprising amount of my day is spent answering messages about Round 2 of Rukia. This form is to get firm numbers on interest, not promise anything. My priority is finishing delivery of Round 1, getting UHMW production up and running, and making sure that my supply chain/logistics issues are fixed and as smooth as possible for upcoming projects.
Please fill this out. All ideas and critiques are welcome.
https://forms.gle/pE5PV8xDtxErkwuu9
Please understand that if I do an aluminum version of what is essentially an Alice clone (if aluminum is what wins out), I would want to offer something that is not easily available through Yuktsi or anyone else (examples: damascus steel weight, acid etched design all over top case, etc.)
Also, anything I make for the next round, if it happens, would be compatible with round 1 Rukia. Example: aluminum top would fit polycarb bottom for half poly build.
Also, please understand, if there is not enough interest, this is really not worth doing. GBs are hard. This is not my brain child--it's Yuktsi's with a twist. I'm working day and night on bringing UHMW to the community. And I'd like as much as possible to break free from the GB format. I much prefer selling in stock products.
I'm not saying it won't ever happen if replies are low, but if they are, it won't be anytime soon.
Post by: vegs on Thu, 02 January 2020, 05:03:41
https://forms.gle/pE5PV8xDtxErkwuu9Filled :thumb:
A surprising amount of my day is spent answering messages about Round 2 of Rukia. This form is to get firm numbers on interest, not promise anything. My priority is finishing delivery of Round 1, getting UHMW production up and running, and making sure that my supply chain/logistics issues are fixed and as smooth as possible for upcoming projects.
Please fill this out. All ideas and critiques are welcome.
https://forms.gle/pE5PV8xDtxErkwuu9
Please understand that if I do an aluminum version of what is essentially an Alice clone (if aluminum is what wins out), I would want to offer something that is not easily available through Yuktsi or anyone else (examples: damascus steel weight, acid etched design all over top case, etc.)
Also, anything I make for the next round, if it happens, would be compatible with round 1 Rukia. Example: aluminum top would fit polycarb bottom for half poly build.
Also, please understand, if there is not enough interest, this is really not worth doing. GBs are hard. This is not my brain child--it's Yuktsi's with a twist. I'm working day and night on bringing UHMW to the community. And I'd like as much as possible to break free from the GB format. I much prefer selling in stock products.
I'm not saying it won't ever happen if replies are low, but if they are, it won't be anytime soon.
Post by: asissle on Thu, 02 January 2020, 10:55:14
Post by: jimboytacos on Thu, 02 January 2020, 15:12:17
https://forms.gle/pE5PV8xDtxErkwuu9
A surprising amount of my day is spent answering messages about Round 2 of Rukia. This form is to get firm numbers on interest, not promise anything. My priority is finishing delivery of Round 1, getting UHMW production up and running, and making sure that my supply chain/logistics issues are fixed and as smooth as possible for upcoming projects.
Please fill this out. All ideas and critiques are welcome.
https://forms.gle/pE5PV8xDtxErkwuu9
Please understand that if I do an aluminum version of what is essentially an Alice clone (if aluminum is what wins out), I would want to offer something that is not easily available through Yuktsi or anyone else (examples: damascus steel weight, acid etched design all over top case, etc.)
Also, anything I make for the next round, if it happens, would be compatible with round 1 Rukia. Example: aluminum top would fit polycarb bottom for half poly build.
Also, please understand, if there is not enough interest, this is really not worth doing. GBs are hard. This is not my brain child--it's Yuktsi's with a twist. I'm working day and night on bringing UHMW to the community. And I'd like as much as possible to break free from the GB format. I much prefer selling in stock products.
I'm not saying it won't ever happen if replies are low, but if they are, it won't be anytime soon.
I highly doubt you'll have insufficient response to run an aluminum GB. In fact, you'll be overwhelmed.
Make this post more public by doing an IC for Rukia R2. Create a new thread. See those interested skyrocket.
Post by: lirtle on Fri, 03 January 2020, 08:11:11
Post by: KingOfMemes on Fri, 24 January 2020, 08:36:56
Post by: lolafineday on Fri, 24 January 2020, 08:41:04
I have fat stacks burning a hole in my wallet if someone wants to make a wrist rest for this bad boyLmfao same
Sent from my SM-G975F using Tapatalk
Post by: pnkpanther65 on Fri, 24 January 2020, 08:48:14
Sent from my Pixel 2 using Tapatalk
Post by: KingOfMemes on Fri, 24 January 2020, 09:04:28
Keyset decisions are always the hardest partAbsolutely that blank jelly set, if you are asking for votesShow Image(https://uploads.tapatalk-cdn.com/20200124/7ca66ee5bb6bd5576118e07b7a4df032.jpg)Show Image(https://uploads.tapatalk-cdn.com/20200124/6bb1fef4fd6013232320b28ce0fe981a.jpg)
Sent from my Pixel 2 using Tapatalk
Post by: Jaxxstatic on Fri, 24 January 2020, 20:04:40
I have fat stacks burning a hole in my wallet if someone wants to make a wrist rest for this bad boyNoahF on Discord is gonna run a wrist rest GB. I'll ask him to put details here as well.
Post by: stubtail42 on Sat, 01 February 2020, 19:24:34
Keyset decisions are always the hardest partShow Image(https://uploads.tapatalk-cdn.com/20200124/7ca66ee5bb6bd5576118e07b7a4df032.jpg)Show Image(https://uploads.tapatalk-cdn.com/20200124/6bb1fef4fd6013232320b28ce0fe981a.jpg)
Sent from my Pixel 2 using Tapatalk
Jelly for sure!
Post by: Ruffles on Tue, 18 February 2020, 01:59:02
Sent from my LYA-L29 using Tapatalk
Post by: Mr.Elli0t on Sat, 21 March 2020, 11:22:07
Post by: Jaxxstatic on Sun, 22 March 2020, 07:46:02
Can someone provide me with the discord channel? Please and thank you :D
Will there be a R2 for rukia? Sorry if I missed out on any updates if there is any.
Sent from my LYA-L29 using Tapatalk
Discord Link (https://discord.gg/eJrjdtg)
Round 2 Store (https://mintautumn.com)
Post by: Vadurr on Sun, 22 March 2020, 13:55:15
Post by: Jaxxstatic on Sun, 22 March 2020, 16:57:47
That's about 2 hours from now.
The link is for a 17-question Star Wars quiz.
Those who get 100% on the quiz (unlimited entry per email), will be emailed a scavenger hunt item.
The first 10 to reply to that email with a picture of themselves and the item or a timestamp (handwritten date + username/email) and the item will be sent the order form for the Rukia LE full green polycarb with Baby Yoda weight *shhhh.
Renders and pricing will be made known to the winners. They are free, however, to share as they wish.
Post by: Jaxxstatic on Sun, 22 March 2020, 18:59:56
Post by: o3okevin on Mon, 23 March 2020, 17:18:43
Post by: _prjctZero on Sun, 23 August 2020, 22:57:43
At 0000 GMT, I'll be posting a link for entry into the Rukia LE, called "The Child."
That's about 2 hours from now.
The link is for a 17-question Star Wars quiz.
Those who get 100% on the quiz (unlimited entry per email), will be emailed a scavenger hunt item.
The first 10 to reply to that email with a picture of themselves and the item or a timestamp (handwritten date + username/email) and the item will be sent the order form for the Rukia LE full green polycarb with Baby Yoda weight *shhhh.
Renders and pricing will be made known to the winners. They are free, however, to share as they wish.
Is this still going?
Post by: sirieous on Mon, 24 August 2020, 05:33:01
At 0000 GMT, I'll be posting a link for entry into the Rukia LE, called "The Child."
That's about 2 hours from now.
The link is for a 17-question Star Wars quiz.
Those who get 100% on the quiz (unlimited entry per email), will be emailed a scavenger hunt item.
The first 10 to reply to that email with a picture of themselves and the item or a timestamp (handwritten date + username/email) and the item will be sent the order form for the Rukia LE full green polycarb with Baby Yoda weight *shhhh.
Renders and pricing will be made known to the winners. They are free, however, to share as they wish.
Is this still going?
No. R2 has already finished. R3 is going to happen after R2 ships.
Post by: _prjctZero on Mon, 24 August 2020, 21:07:46
At 0000 GMT, I'll be posting a link for entry into the Rukia LE, called "The Child."
That's about 2 hours from now.
The link is for a 17-question Star Wars quiz.
Those who get 100% on the quiz (unlimited entry per email), will be emailed a scavenger hunt item.
The first 10 to reply to that email with a picture of themselves and the item or a timestamp (handwritten date + username/email) and the item will be sent the order form for the Rukia LE full green polycarb with Baby Yoda weight *shhhh.
Renders and pricing will be made known to the winners. They are free, however, to share as they wish.
Is this still going?
No. R2 has already finished. R3 is going to happen after R2 ships.
Ohh sorry i meant the quiz for The Child version
Post by: Sup on Tue, 25 August 2020, 14:04:21
At 0000 GMT, I'll be posting a link for entry into the Rukia LE, called "The Child."
That's about 2 hours from now.
The link is for a 17-question Star Wars quiz.
Those who get 100% on the quiz (unlimited entry per email), will be emailed a scavenger hunt item.
The first 10 to reply to that email with a picture of themselves and the item or a timestamp (handwritten date + username/email) and the item will be sent the order form for the Rukia LE full green polycarb with Baby Yoda weight *shhhh.
Renders and pricing will be made known to the winners. They are free, however, to share as they wish.
Is this still going?
No. R2 has already finished. R3 is going to happen after R2 ships.
Ohh sorry i meant the quiz for The Child version
Already happened months ago
Post by: basedRNC on Sat, 21 November 2020, 15:19:20
https://imgshare.io/image/d6367515-4a91-493f-a868-3d4604ef652d.NJ0Ufl
I’m afraid to pry it out to damage the polycarbonate. I’ve also tried “tapping” it out with a hammer and punch but don’t want to hammer too hard.
Sent from my iPhone using Tapatalk
Post by: Jaxxstatic on Sat, 21 November 2020, 16:08:10
Post by: lonalde on Sun, 22 November 2020, 19:35:25
Post by: thebreadsaver on Fri, 04 December 2020, 00:03:18
Post by: Mr.Elli0t on Fri, 04 December 2020, 12:44:23
https://www.mintautumn.com/contact.html#/
Post by: Mr.Elli0t on Fri, 04 December 2020, 12:44:58
damn...got into the hobby after the end of r2 :'). gonna be keeping a close eye for r3
https://www.mintautumn.com/contact.html#/