geekhack
geekhack Community => Reviews => Topic started by: skuko on Fri, 07 August 2015, 10:34:14
-
hi guys,
so there's seems to be quite some confusion on about these boards, let me put in my two cents.
from the first time i saw this board, fell in love with it's case, very low profile, "floating" caps design, without any ugly logos on it (unlike the noppoo "lolita" bull****).
unfortunately, there is a lot of confusion, because apparently these boards come in different varieties and noone seems to be able to identify which is actually which.
so far i have seen
- board without backlighting and costar stabs
- board without backlighting and cherry stabs
- the above with different kinds of leds and either costar or cherry stabs
- and then there are the variants with gateron switches.
at first, i really hunted for a mx clear version, but those are extremely hard to come by and AFAIK were only available during the first massdrop buy. i did not want to buy it then and afterwards i was bummed out to find that they didn't offer mx clears in any of the subsequent drops.
anyway, i made the switch from tactile (topre 45g FC660C) back to linear (mx reds), pulled out my trusty filco and found my old love for the light switch :) this time around i have ordered this board from ebay (joliesanz), even though it was significantly more expensive than anything else i saw either on ebay or aliexpress, because according to their pictures this was the board with costar stabs (which i do prefer over cherry stabs) and genuine cherry mx red switches.
it was almost 200$ shipped, but i bit the bullet and now i'm typing this review on it.
i must say i love the board, it is way more silent than the filco or the QFR stealth with mx reds i have. this is because of the extremely low profiel case not echoing the bottoming out sounds (or at least i think so).
the board is built extremely well, i will post pictures later. it came with costar stabs, but they were in the inner positions, so the spacebar inserts were in the non-standard position and the spacebar wire is shorter. i have switched them into the outer positions and changed the wire from a QFR stealth and put on imsto thick pbt caps. (again, pics will follow later) it has a very nice silver coated plate and even though it has some scratches/smudges, they're not visible during normal use, it doesn't bother me.
my only gripe is that it wobbles just a tiny bit. the bottom left corner is a bit in the air and i cannot identify whether the whole case is bent (because it's just a really tiny bit), or the rubber foot in the bottom left corner is a bit shorter. right now as i am typing though (and bagning it hard, bottoming out and all), i cannot feel it wobbling, i have to deliberately push the casing in the bottom left corner to actually feel it wobble, so i guess it's ok :)
i have some pics and will post them later when i am at home, or tomorrow.
bottomline - my board is the VA87MR, cherry mx red switches, no backlight (except for caps and scroll lock leds), white case. i think the GMK classic beige will look totally sexy on this :)
exactly this one
http://www.ebay.com/itm/Varmilo-Mechanical-Keyboard-Cherry-MX-Switch-White-Body-Blue-Key-Red-Switches-/331591054821?ssPageName=ADME:X:RTQ:US:1123
except if you look at their pictures closely, it shows the costar stabs in the outer positions, which is not true, they were in the inner positions.
edit:
adding pics, as promised :) excuse the potato quality, i only have an xperia z2, no proper camera :(
spacebar comparison - top imsto thick PBT, bottom varmilo PBT stock, as you can see, it has standard stem spacing, but original inserts are in the non standard (leopold, i guess) positions
[attach=1]
original PBT caps and what it looked like after replacing the costar stab wire with the one from QFR stealth
[attach=2]
full imsto cherry profile thick PBT set on, i think it's SHMEXY :)
[attach=3]
[attach=4]
[attach=5]
blurry, but you can see on the left how the foot floats about half a milimeter above the table (and no, my table is not bent :) )
[attach=6]
some barebones photos before the storm :), also you can see that the plate is pretty nice, even though it has some scuffs/scratches...
[attach=7]
[attach=8]
[attach=9]
oh SNAP! looks like a unicorn vomited on my board LOL (lovely matt3o's PBT granite DSA - one of the most beautiful sets i have seen)
[attach=10]
[attach=11]
also, worth mentioning that it came with some extra stabilizer mounts and inserts, which is always nice
[attach=12]
now i just need to order some extra stabilizer wires :)
-
(http://i.imgur.com/SJg8k4T.gif)
-
Nice review, I really wan't to try one of these boards out. I have fixed a similar wobble just by twisting the whole board in the opposite direction of the wobble.
-
pictures added, sorry for the poor quality :)
-
:thumb: :thumb:
-
I just joined the Massdrop buy for this which ends today. I'm getting a white case, Gateron blacks, mint front-printed caps, and white LEDs.
I'm not sure why I want this board. I'm not a huge TKL person. I'm not big on backlighting. I generally prefer custom boards. And yet here I am.
-
Nice review, I really wan't to try one of these boards out. I have fixed a similar wobble just by twisting the whole board in the opposite direction of the wobble.
tried it, didn't budge. this is built like a tank.
-
Nice review, I really wan't to try one of these boards out. I have fixed a similar wobble just by twisting the whole board in the opposite direction of the wobble.
tried it, didn't budge. this is built like a tank.
I would try some coarse sandpaper on the bumpons. Just whittle them down until they're all even.
-
i recently seen all types of varmilo on massdrop. good write up, i was curious on how these boards were.
-
nice review sir :thumb:
for gateron switch also uses costar stabillizers too?
-
Great review mane, most dope! ;D