If we purchase the RGB version will the RGB LEDs also come soldered like the controller parts?I offer soldering services in a thread I have, and for this GB I will be offering Resistors & Diodes, but if you are requesting more than just that, PM me and we can work out the details. My thread can be seen here: https://geekhack.org/index.php?topic=73610
@sethk_ Can you expand on the extent of soldering services you're providing? I'm trying to figure out if that's something I need.
Forgive me, this was probably asked and answered in the IC thread but I'm not seeing it.
The OP could use more details. We should not assume everyone interested in this GB has read through the IC.It does not include parts for diodes and resistors.
Do the PCBs include unsoldered diodes and/or resistors? If not, what diodes or resistors are needed?
What layouts does the FingerSK support?
What is a "Panda design"? Is this an option that will be added later to the order form?
How are the RGB SMD leds controlled? Are they controlled at all? What comes presoldered? Any diodes, resistors, etc?Only controller parts come Presoldered AFAIK, not sure about RGB LEDs. For 15$, I am offering a service where I will solder on the diodes & resistors. If you need more than just that for assembly, you can see my thread where I posted it earlier in this post.
Are there any finished examples of the FingerUP 65%?This is the one that is used inside LZ SQs I believe
Are there any finished examples of the FingerUP 65%?This is the one that is used inside LZ SQs I believe
If we purchase the RGB version will the RGB LEDs also come soldered like the controller parts?I offer soldering services in a thread I have, and for this GB I will be offering Resistors & Diodes, but if you are requesting more than just that, PM me and we can work out the details. My thread can be seen here: https://geekhack.org/index.php?topic=73610
@sethk_ Can you expand on the extent of soldering services you're providing? I'm trying to figure out if that's something I need.
Forgive me, this was probably asked and answered in the IC thread but I'm not seeing it.The OP could use more details. We should not assume everyone interested in this GB has read through the IC.It does not include parts for diodes and resistors.
Do the PCBs include unsoldered diodes and/or resistors? If not, what diodes or resistors are needed?
What layouts does the FingerSK support?
What is a "Panda design"? Is this an option that will be added later to the order form?
These are the diodes you will need: http://www.mouser.com/Search/ProductDetail.aspx?R=1N4148W-7-Fvirtualkey62110000virtualkey621-1N4148W-F
And resistors come in different Ohms, but this is the general type, and you can find other Ohms: http://www.mouser.com/Search/ProductDetail.aspx?R=ERJ-6ENF8060Vvirtualkey66720000virtualkey667-ERJ-6ENF8060V
Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide
Leeku's new PCBs all support similar layout options.How are the RGB SMD leds controlled? Are they controlled at all? What comes presoldered? Any diodes, resistors, etc?Only controller parts come Presoldered AFAIK, not sure about RGB LEDs. For 15$, I am offering a service where I will solder on the diodes & resistors. If you need more than just that for assembly, you can see my thread where I posted it earlier in this post.
Hey everyone, was pretty busy today, Diodes and Resistors are not included, if they are needed I can source them and include 100x with each order for a bit more.
More photos will be added tonight or tomorrow!
The $5 RGB chip will come soldered on :)
i'd be in for sure if there's a case and plate made made for it.We are in talks, there might be an acrylic case option!
What's the status with the case?
In for a FingerSK, and definitely interested in an acrylic case
What's the status with the case?
From the look of it, (I'm in for the FC660M looking 'fingerup') two pieces of acrylic would be more than adequate but I'd need the .DXFs to go that route.
Actually, speaking of the DIY case route Meiosis, can you find out if a metal "rim" would be a problem? That is, let's say you were to get an aluminum layered case ... would it short anything out if the "acrylic" case were made of metal (e.g. cut by big blue saw)?
How long will this buy be running? I would like to wait and see what case options will be made available, if any. Very interested in the 75% though.Cases are still being discussed, I will try to run it by someone who has made them before... As for affordability of the cases I don't know what MOQ would be feasible so I have been skeptical to give an exact answer to whether they will be an option.
If anyone wants to change their order just submit another one! I'll go through and just use the most current!
Split spacebar but no ISO ? :(theres ISO
Do we know what controller this uses?
All of the firmware stuff I've seen about Leeku boards is Windows-only, if so, this is going to be a problem.
If it uses an ATMEL atmega32XX maybe I can port tmk from @hasu.
Do we know what controller this uses?
All of the firmware stuff I've seen about Leeku boards is Windows-only, if so, this is going to be a problem.
If it uses an ATMEL atmega32XX maybe I can port tmk from @hasu.
How complicated is the key mapping you are planning, if you would like I could flash it to your preferred layout or hot keys. You are ordering assembly
Too? From the form haha
As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.
As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.
Would be very interested if there's a case and plate with it :) (75%)
keep us updated!
As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.
Would a Winkeyless B.mini case be compatible with this?Yes
Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.
My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?
oh no... I did not need to see that... and if there is a 65% option like this, I expect a chorus of tears from every bank account I have.
Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.
My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?
Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housingShow Image(http://kbdlab.co.kr/files/attach/images/340/187/640/002/084007388d3e62b78d860d051dc830a4.jpg)
this might be happening..
Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.
My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?
Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housingShow Image(http://kbdlab.co.kr/files/attach/images/340/187/640/002/084007388d3e62b78d860d051dc830a4.jpg)
this might be happening..
Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide (http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide)
Leeku's new PCBs all support similar layout options.
It does, I don't think that guide shows it though
Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide (http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide)
Leeku's new PCBs all support similar layout options.
Wait, so this board wont support ISO?
Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.
My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?
Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housingShow Image(http://kbdlab.co.kr/files/attach/images/340/187/640/002/084007388d3e62b78d860d051dc830a4.jpg)
this might be happening..
I'd like to cancel my order please.
Any idea what cases the FingerSK would fit into, and what bottom row layouts are supported?MX-Mini compatible cases, and I believe I linked the layout info earlier
Any idea what cases the FingerSK would fit into, and what bottom row layouts are supported?MX-Mini compatible cases, and I believe I linked the layout info earlier
Can i just get a confirmation that the FingerSK supports the same split spacebar bottom row as the FingerUP/L3?
So im a little confused. Its the 8th and i havent received an invoice even though I put in my order? is the invoice date still the 7th?
I just caught up with the thread. is this actually ended? The date in the OP is different than what's been stated in the comments.
Question: Will there be custom AEK2 cases available for the PCB, or is this just intended to be a swap into AEK2 cases?It's made to be put into an old AEK2 case, and would be programmable, sadly no custom will be made for it in the meantime..
Unfortunately, I only have an AEKI, so it might not be compatible even though I think they would be similar enough, but the angles are different. I would like something to put my Orange Alps into.
Does anyone know what plate would work with the FingerUp?I messed up a bit on the name, all the plates from the previous 65% GB have been bought out, there is a chance there might be another run soon, but in the meanwhile I don't have an answer for it