« previous next »
Pages:  [1]     Go Down

Author Topic: stabs overlap cutout?  (Read 1300 times)

0 Members and 1 Guest are viewing this topic.

Offline Eszett

  • Thread Starter
  • Posts: 543
  • Supporting the communities Geekhack & Deskthority
stabs overlap cutout?
« on: Sun, 20 December 2015, 07:58:26 »
Hi! How much does Cherry plate mount stabs overlap their cutouts? I need to know mainly on the critical yellow spot ... 120881-0
Logged

Offline suicidal_orange

  • * Global Moderator
  • Posts: 4771
  • Location: England
Re: stabs overlap cutout?
« Reply #1 on: Sun, 20 December 2015, 09:36:31 »
I'm not 100% sure but the stabs on my Ducky (not new funky ones) aren't the same as the PCB mount ones I have in a bag, so I think the answer is they don't at least on top of the plate.



If these look right I can take the board apart and try and look at the back, but not sure how accurate I'll be with a PCB attached...
Logged
120/100g linear Zealio R1  
GMK Hyperfuse
'Split everything' perfection   		MX Clear
SA Hack'd by Geeks     
EasyAVR mod

Offline Eszett

  • Thread Starter
  • Posts: 543
  • Supporting the communities Geekhack & Deskthority
Re: stabs overlap cutout?
« Reply #2 on: Sun, 20 December 2015, 11:04:18 »
Hi orange. They don't overlap at all? really!?
Logged

Offline suicidal_orange

  • * Global Moderator
  • Posts: 4771
  • Location: England
Re: stabs overlap cutout?
« Reply #3 on: Sun, 20 December 2015, 12:11:56 »
You can see the front of the hole level with the bottom of the stab in the pic, so no.  I guess there is some overlap underneath or it couldn't clip in but wasn't sure if you were worried about top, bottom or both so didn't take it apart.  Say the word and I will :)
Logged
120/100g linear Zealio R1  
GMK Hyperfuse
'Split everything' perfection   		MX Clear
SA Hack'd by Geeks     
EasyAVR mod

Offline Eszett

  • Thread Starter
  • Posts: 543
  • Supporting the communities Geekhack & Deskthority
Re: stabs overlap cutout?
« Reply #4 on: Sun, 20 December 2015, 12:33:02 »
Hi orange. The word is "please"?
Logged

Offline suicidal_orange

  • * Global Moderator
  • Posts: 4771
  • Location: England
Re: stabs overlap cutout?
« Reply #5 on: Sun, 20 December 2015, 12:50:47 »
I only meant confirmation that you wanted the back, wasn't treating you like my two year old niece :))

Unfortunately the plate bends round and damn near touches the PCB so I can't see or measure anything:(
Logged
120/100g linear Zealio R1  
GMK Hyperfuse
'Split everything' perfection   		MX Clear
SA Hack'd by Geeks     
EasyAVR mod

Offline Eszett

  • Thread Starter
  • Posts: 543
  • Supporting the communities Geekhack & Deskthority
Re: stabs overlap cutout?
« Reply #6 on: Sun, 20 December 2015, 13:05:37 »
Hi orange. I'm asking, because on top of the metal plate I plan another thin layer for fairing, to avoid the
"floating keys" look. And if the stabs overlap, then I need enlarged cutouts on that fairing layer. Thanks so far!
« Last Edit: Sun, 20 December 2015, 23:56:15 by Eszett »
Logged
Pages:  [1]     Go Up
« previous next »