Author Topic: [GB COMPLETE] SaiB - CP  (Read 79912 times)

0 Members and 1 Guest are viewing this topic.

Online LightningXI

  • * Elevated Elder
  • Posts: 3021
  • Location: New York
  • PPD
    • ArtisanMacro
Re: [GB COMPLETE] SaiB - CP
« Reply #500 on: Sun, 17 February 2019, 02:49:34 »


Hi everyone, I'm not sure if this would still help, but I want to point out the fact that the runner's uploaded drawing of the bottom plate is incorrect in the four corners. I was able to ask a friend of mine of modify the drawing so that it would fit in the cutout on the bottom, and you can download it below.

Please note that the thickness of the plate is 3mm, and while it was the best my friend could do off of the original drawing, it's still not a 100% fit. I had to shave off 2 corners of the plate a bit further, but the result was more than ok, at least better than having an empty space.

Cool observation. Much appreciated that you've decide to share the finding and the file. Do you have pics of what this ended up looking like?
WANTED: Clacks, Artisans, Keysets, Vintage Cherry and Other Goodies

More
Quickfire Pro | TADA 68 | Novatouch | Whitefox | Octagon v1 | Blackbird | HHKB Pro 2 | KBD75 | VE.A | X60 | Canoe | HHKB Pro 1 | FJELL | Revo One | ALPS64 | Lightsaver v3 | IBM 5140 WKL | Realforce 87u | MIRA SE | Duck Poker | Canoe | Moon | Weaven | M65-A | EXENT | Wooden Planck | Tokyo60 | Viper v1 | E6-v2 | IBM SSK | CA66 | TX-CP | SINGA | TGR Alice | FJELL R2 | Klippe | JER-A06 | GSKT-00 | M60-A | Realforce 84u | AL1 | Keycult No. 1 | SaiB-CP | G81-3077SAU | DC60 | Realforce 84ub | TMO50 | G80-1800 | Leaf 80 | LZ GH-v2 | T60 | LZ MP | KMAC Happy | TGR-910RE (Al) | TGR-910RE (PC) | SKB60 | UNIKORN | IBM 3278 (pending restoration) | KFE | TGR Jane v2 | TGR Jane v2 CE | Koala | iS0 | Norbatouch | KPad | Xeno | F62 Kishsaver | Keycult No.1/60 Rev. 1 | GSKT-00 Z | Jubi | Montage


Offline flying1911

  • Posts: 104
Re: [GB COMPLETE] SaiB - CP
« Reply #501 on: Sun, 17 February 2019, 03:20:38 »


Hi everyone, I'm not sure if this would still help, but I want to point out the fact that the runner's uploaded drawing of the bottom plate is incorrect in the four corners. I was able to ask a friend of mine of modify the drawing so that it would fit in the cutout on the bottom, and you can download it below.

Please note that the thickness of the plate is 3mm, and while it was the best my friend could do off of the original drawing, it's still not a 100% fit. I had to shave off 2 corners of the plate a bit further, but the result was more than ok, at least better than having an empty space.

Cool observation. Much appreciated that you've decide to share the finding and the file. Do you have pics of what this ended up looking like?

For sure:



I've only tried it with black mica, which cost like $2 for the piece and it looks pretty good. Will definitely come to a more permanent solution such as stainless steel in the future.
TGR 910CE | TGR Jane CE | TGR Jane V2 CE | Keycult OG No.1 WKL | Cherry G81-3100 SAV | IBM Model M SSK

Online LightningXI

  • * Elevated Elder
  • Posts: 3021
  • Location: New York
  • PPD
    • ArtisanMacro
Re: [GB COMPLETE] SaiB - CP
« Reply #502 on: Sun, 17 February 2019, 03:25:55 »


Hi everyone, I'm not sure if this would still help, but I want to point out the fact that the runner's uploaded drawing of the bottom plate is incorrect in the four corners. I was able to ask a friend of mine of modify the drawing so that it would fit in the cutout on the bottom, and you can download it below.

Please note that the thickness of the plate is 3mm, and while it was the best my friend could do off of the original drawing, it's still not a 100% fit. I had to shave off 2 corners of the plate a bit further, but the result was more than ok, at least better than having an empty space.

Cool observation. Much appreciated that you've decide to share the finding and the file. Do you have pics of what this ended up looking like?

For sure:

Show Image


I've only tried it with black mica, which cost like $2 for the piece and it looks pretty good. Will definitely come to a more permanent solution such as stainless steel in the future.
Wow, very neat. If you manage to do it in metal, and you have to edit the file again (since you have to still shave off a few milimeters) would you mind sharing that again? I'd be interested in getting one done in steel as well.
WANTED: Clacks, Artisans, Keysets, Vintage Cherry and Other Goodies

More
Quickfire Pro | TADA 68 | Novatouch | Whitefox | Octagon v1 | Blackbird | HHKB Pro 2 | KBD75 | VE.A | X60 | Canoe | HHKB Pro 1 | FJELL | Revo One | ALPS64 | Lightsaver v3 | IBM 5140 WKL | Realforce 87u | MIRA SE | Duck Poker | Canoe | Moon | Weaven | M65-A | EXENT | Wooden Planck | Tokyo60 | Viper v1 | E6-v2 | IBM SSK | CA66 | TX-CP | SINGA | TGR Alice | FJELL R2 | Klippe | JER-A06 | GSKT-00 | M60-A | Realforce 84u | AL1 | Keycult No. 1 | SaiB-CP | G81-3077SAU | DC60 | Realforce 84ub | TMO50 | G80-1800 | Leaf 80 | LZ GH-v2 | T60 | LZ MP | KMAC Happy | TGR-910RE (Al) | TGR-910RE (PC) | SKB60 | UNIKORN | IBM 3278 (pending restoration) | KFE | TGR Jane v2 | TGR Jane v2 CE | Koala | iS0 | Norbatouch | KPad | Xeno | F62 Kishsaver | Keycult No.1/60 Rev. 1 | GSKT-00 Z | Jubi | Montage


Offline flying1911

  • Posts: 104
Re: [GB COMPLETE] SaiB - CP
« Reply #503 on: Sun, 17 February 2019, 05:53:20 »
To be honest the amount of shaving was so minimal I intend to stop making further changes to the file, and there's a possibility it could get worse. I imagine the stainless steel piece will have to be polished to look good anyway, so you can make sure that it fits before having it done. Again, I only had to shave half a mm of material off 2 corners.

Good luck with your project, I'm sure it'll be worth it  :thumb: :thumb:
TGR 910CE | TGR Jane CE | TGR Jane V2 CE | Keycult OG No.1 WKL | Cherry G81-3100 SAV | IBM Model M SSK

Offline forumusername

  • Posts: 161
Re: [GB COMPLETE] SaiB - CP
« Reply #504 on: Fri, 22 February 2019, 10:19:31 »
I've got a titan grey kit that I'd like to part with its unbuilt pm me if you are interested :thumb:

Online yaya

  • Posts: 55
Re: [GB COMPLETE] SaiB - CP
« Reply #505 on: Tue, 05 March 2019, 11:52:19 »
Has anyone made any more progress on getting a weight made?

Offline forumusername

  • Posts: 161
Re: [GB COMPLETE] SaiB - CP
« Reply #506 on: Tue, 02 April 2019, 22:21:22 »
I either lost the screws that came with my kit or didn't get them... in either case can someone educate me on what screws I need for the kit please and thank you

Offline Vloshko

  • Posts: 165
  • Location: Cali, Colorado, & Israel
Re: [GB COMPLETE] SaiB - CP
« Reply #507 on: Sun, 21 April 2019, 18:33:41 »
Just found out plate is too tight for 7u spacebar. Easy 30 second fix by filing right metal side of left stabilizer
« Last Edit: Sun, 21 April 2019, 19:10:14 by Vloshko »
Keycap Compendium

Discord: Vloshko#1327

Key Cap Wishlist

2019: Configure Optimal Audio Settings

HHKB Pro 2, Model M, Unicorn X Legend, ESPECTRO 96, SaiB CP, E8-V1.

Offline Vloshko

  • Posts: 165
  • Location: Cali, Colorado, & Israel
Re: [GB COMPLETE] SaiB - CP
« Reply #508 on: Sun, 21 April 2019, 18:38:14 »
I either lost the screws that came with my kit or didn't get them... in either case can someone educate me on what screws I need for the kit please and thank you

9/16" long
Strangely looks like 2/10 cm diameter
« Last Edit: Sun, 21 April 2019, 18:46:16 by Vloshko »
Keycap Compendium

Discord: Vloshko#1327

Key Cap Wishlist

2019: Configure Optimal Audio Settings

HHKB Pro 2, Model M, Unicorn X Legend, ESPECTRO 96, SaiB CP, E8-V1.

Offline forumusername

  • Posts: 161
Re: [GB COMPLETE] SaiB - CP
« Reply #509 on: Sun, 21 April 2019, 18:43:25 »
I either lost the screws that came with my kit or didn't get them... in either case can someone educate me on what screws I need for the kit please and thank you

9/16" long
Thank you!

Offline Vloshko

  • Posts: 165
  • Location: Cali, Colorado, & Israel
Re: [GB COMPLETE] SaiB - CP
« Reply #510 on: Wed, 24 April 2019, 21:34:30 »
Is there supposed to be a gasket for this for the leds?
Keycap Compendium

Discord: Vloshko#1327

Key Cap Wishlist

2019: Configure Optimal Audio Settings

HHKB Pro 2, Model M, Unicorn X Legend, ESPECTRO 96, SaiB CP, E8-V1.

Online LightningXI

  • * Elevated Elder
  • Posts: 3021
  • Location: New York
  • PPD
    • ArtisanMacro
Re: [GB COMPLETE] SaiB - CP
« Reply #511 on: Wed, 24 April 2019, 21:37:52 »
Is there supposed to be a gasket for this for the leds?
Not really. Mine has the LEDs on.
WANTED: Clacks, Artisans, Keysets, Vintage Cherry and Other Goodies

More
Quickfire Pro | TADA 68 | Novatouch | Whitefox | Octagon v1 | Blackbird | HHKB Pro 2 | KBD75 | VE.A | X60 | Canoe | HHKB Pro 1 | FJELL | Revo One | ALPS64 | Lightsaver v3 | IBM 5140 WKL | Realforce 87u | MIRA SE | Duck Poker | Canoe | Moon | Weaven | M65-A | EXENT | Wooden Planck | Tokyo60 | Viper v1 | E6-v2 | IBM SSK | CA66 | TX-CP | SINGA | TGR Alice | FJELL R2 | Klippe | JER-A06 | GSKT-00 | M60-A | Realforce 84u | AL1 | Keycult No. 1 | SaiB-CP | G81-3077SAU | DC60 | Realforce 84ub | TMO50 | G80-1800 | Leaf 80 | LZ GH-v2 | T60 | LZ MP | KMAC Happy | TGR-910RE (Al) | TGR-910RE (PC) | SKB60 | UNIKORN | IBM 3278 (pending restoration) | KFE | TGR Jane v2 | TGR Jane v2 CE | Koala | iS0 | Norbatouch | KPad | Xeno | F62 Kishsaver | Keycult No.1/60 Rev. 1 | GSKT-00 Z | Jubi | Montage


Offline forumusername

  • Posts: 161
Re: [GB COMPLETE] SaiB - CP
« Reply #512 on: Sun, 28 April 2019, 18:05:17 »
I either lost the screws that came with my kit or didn't get them... in either case can someone educate me on what screws I need for the kit please and thank you

9/16" long
Strangely looks like 2/10 cm diameter
I am actually a little confused on what you are referring to any way you could link me or if anyone else could chime in I'd greatly appreciate it!

Online yaya

  • Posts: 55
Re: [GB COMPLETE] SaiB - CP
« Reply #513 on: Mon, 29 April 2019, 07:34:36 »
I either lost the screws that came with my kit or didn't get them... in either case can someone educate me on what screws I need for the kit please and thank you

Pretty sure they are twelve M3 x 15mm countersunk allen screws
« Last Edit: Mon, 29 April 2019, 07:37:00 by yaya »

Offline Carlobv

  • Posts: 50
Re: [GB COMPLETE] SaiB - CP
« Reply #514 on: Thu, 09 May 2019, 09:20:48 »
Hey guys, troubleshooting question if anyone can help:

I spilled some beer on my board last night.  I disconnected from the computer and cleaned it.  It didn't seem too bad.

Nothing worked on reconnect, but I loaded new firmware and was able to connect.  Everything is working fine until I disconnect from usb.  When I reconnect, I hear the "something is connecting via usb sound," but the board doesn't work until I flash the firmware again. 

Any ideas?

Offline dubious

  • 쏘쿨
  • Posts: 571
  • Location: shralpin the gnar
Re: [GB COMPLETE] SaiB - CP
« Reply #515 on: Thu, 09 May 2019, 18:31:08 »
Hey guys, troubleshooting question if anyone can help:

I spilled some beer on my board last night.  I disconnected from the computer and cleaned it.  It didn't seem too bad.

Nothing worked on reconnect, but I loaded new firmware and was able to connect.  Everything is working fine until I disconnect from usb.  When I reconnect, I hear the "something is connecting via usb sound," but the board doesn't work until I flash the firmware again. 

Any ideas?

Something is probably fried if it wont hold firmware, but it's possible something is being shorted. How long did you wait until you plugged it back in, and did you do anything besides just wipe up the beer? (Like put the pcb/plate/switches in rice, or silica or wtvr)

Offline Puddsy

  • nice
  • * Elated Elder
  • Posts: 11323
  • "Do you shovel to survive, or survive to shovel?"
Re: [GB COMPLETE] SaiB - CP
« Reply #516 on: Thu, 09 May 2019, 18:42:43 »
Hey guys, troubleshooting question if anyone can help:

I spilled some beer on my board last night.  I disconnected from the computer and cleaned it.  It didn't seem too bad.

Nothing worked on reconnect, but I loaded new firmware and was able to connect.  Everything is working fine until I disconnect from usb.  When I reconnect, I hear the "something is connecting via usb sound," but the board doesn't work until I flash the firmware again. 

Any ideas?

sounds like something the controller fried or is shorting

might be worth going over those contacts with a bit of iso alcohol and seeing if that helps

but if it doesn't hold firmware it's probably screwed
QFR | MJ2 TKL | "Bulgogiboard" (Keycon 104) | TGR Alice | Qlavier Ti/Acryl Alice

"Everything is worse, but in a barely perceptible and indefinable way" -dollartacos

Offline PainMaster

  • Formerly cjakma
  • Thread Starter
  • Posts: 152
  • Location: SungNam, south korea
  • IBM(PainMaster)
Re: [GB COMPLETE] SaiB - CP
« Reply #517 on: Thu, 20 June 2019, 00:54:05 »
WOW -

I read this by chance.

I'm surprised that communication happen yet.

Thank you very much for your interest. !!!


If you have any questions, please tell me in the comments.

I'll answer as much as I can.

-----------------------------------------------------

During the production of SAB-CP,

In order not to reproduce the hard work that had to be done unintentionally,

I'm developing our own PCB (with QMK).


221453-0
Fail to purchase GMK Olivia T^T
SaiB-CP Black - Kailh Bronze (Non Click / 58g) - Finish
Light Saver v1 Black - Cherry Wyze Black (Linear / 64g)
Light Saver v2 Gray - Cherry 1501 Black (Linear / 64g)
Light Saver v3 Silver - Cherry 8200 White (Non Click / 64g)
Light Saver Acryl (Duck96 base) - Gateron Yellow (Linear / 62g) - Season 1 Fin.
Octagon v1 Black - Cherry 1501 Black (Linear / 64g) / TX-1800 v1 Red/Black - Cherry Wyze Black (Linear / 58g)
VE.A Test Housing- Cherry 8113 White (Non Click / 58g)
TC-V3 , LZ*ASRH Black, VE.A 2nd
... etc.

Offline PainMaster

  • Formerly cjakma
  • Thread Starter
  • Posts: 152
  • Location: SungNam, south korea
  • IBM(PainMaster)
Re: [GB COMPLETE] SaiB - CP
« Reply #518 on: Thu, 20 June 2019, 00:56:42 »
WOW -

I read this by chance.

I'm surprised that communication happen yet.

Thank you very much for your interest. !!!


If you have any questions, please tell me in the comments.

I'll answer as much as I can.

-----------------------------------------------------

During the production of SAB-CP,

In order not to reproduce the hard work that had to be done unintentionally,

I'm developing our own 3 types PCB (with QMK).

80%

60%

OTD replica

(http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=5822124)

(Attachment Link)

(Attachment Link)

(Attachment Link)

Fail to purchase GMK Olivia T^T
SaiB-CP Black - Kailh Bronze (Non Click / 58g) - Finish
Light Saver v1 Black - Cherry Wyze Black (Linear / 64g)
Light Saver v2 Gray - Cherry 1501 Black (Linear / 64g)
Light Saver v3 Silver - Cherry 8200 White (Non Click / 64g)
Light Saver Acryl (Duck96 base) - Gateron Yellow (Linear / 62g) - Season 1 Fin.
Octagon v1 Black - Cherry 1501 Black (Linear / 64g) / TX-1800 v1 Red/Black - Cherry Wyze Black (Linear / 58g)
VE.A Test Housing- Cherry 8113 White (Non Click / 58g)
TC-V3 , LZ*ASRH Black, VE.A 2nd
... etc.

Online LightningXI

  • * Elevated Elder
  • Posts: 3021
  • Location: New York
  • PPD
    • ArtisanMacro
Re: [GB COMPLETE] SaiB - CP
« Reply #519 on: Thu, 20 June 2019, 02:52:04 »
WOW -

I read this by chance.

I'm surprised that communication happen yet.

Thank you very much for your interest. !!!


If you have any questions, please tell me in the comments.

I'll answer as much as I can.

-----------------------------------------------------

During the production of SAB-CP,

In order not to reproduce the hard work that had to be done unintentionally,

I'm developing our own 3 types PCB (with QMK).

80%

60%

OTD replica

(http://kbdlab.co.kr/index.php?mid=board_Lsno50&document_srl=5822124)

(Attachment Link)

(Attachment Link)

(Attachment Link)

This looks promising and exciting. Now, where to find an OTD so I can use that latter PCB....

WANTED: Clacks, Artisans, Keysets, Vintage Cherry and Other Goodies

More
Quickfire Pro | TADA 68 | Novatouch | Whitefox | Octagon v1 | Blackbird | HHKB Pro 2 | KBD75 | VE.A | X60 | Canoe | HHKB Pro 1 | FJELL | Revo One | ALPS64 | Lightsaver v3 | IBM 5140 WKL | Realforce 87u | MIRA SE | Duck Poker | Canoe | Moon | Weaven | M65-A | EXENT | Wooden Planck | Tokyo60 | Viper v1 | E6-v2 | IBM SSK | CA66 | TX-CP | SINGA | TGR Alice | FJELL R2 | Klippe | JER-A06 | GSKT-00 | M60-A | Realforce 84u | AL1 | Keycult No. 1 | SaiB-CP | G81-3077SAU | DC60 | Realforce 84ub | TMO50 | G80-1800 | Leaf 80 | LZ GH-v2 | T60 | LZ MP | KMAC Happy | TGR-910RE (Al) | TGR-910RE (PC) | SKB60 | UNIKORN | IBM 3278 (pending restoration) | KFE | TGR Jane v2 | TGR Jane v2 CE | Koala | iS0 | Norbatouch | KPad | Xeno | F62 Kishsaver | Keycult No.1/60 Rev. 1 | GSKT-00 Z | Jubi | Montage


Offline poolside

  • Posts: 777
  • Location: On the deck
Re: [GB COMPLETE] SaiB - CP
« Reply #520 on: Thu, 20 June 2019, 17:28:33 »
> 2018-09-28 Update.
   
    SaiB - CP's Bottom weight plate Document Open !

    You can edit it, as long as you specify the source (SaiB - CP).

    (Attachment Link)

Hi everyone, I'm not sure if this would still help, but I want to point out the fact that the runner's uploaded drawing of the bottom plate is incorrect in the four corners. I was able to ask a friend of mine of modify the drawing so that it would fit in the cutout on the bottom, and you can download it below.

Please note that the thickness of the plate is 3mm, and while it was the best my friend could do off of the original drawing, it's still not a 100% fit. I had to shave off 2 corners of the plate a bit further, but the result was more than ok, at least better than having an empty space.

Hey PainMaster, could you please release a fixed weight plate file? Did you have weight plates made for your personal SaiB-CPs?
The plate corner radius in your original file seems to be incorrect. It is about 5.5mm whereas the actual bottom piece weight plate cutout has corner radiuses closer to 10mm.

Offline PainMaster

  • Formerly cjakma
  • Thread Starter
  • Posts: 152
  • Location: SungNam, south korea
  • IBM(PainMaster)
Re: [GB COMPLETE] SaiB - CP
« Reply #521 on: Fri, 21 June 2019, 00:24:18 »
> 2018-09-28 Update.
   
    SaiB - CP's Bottom weight plate Document Open !

    You can edit it, as long as you specify the source (SaiB - CP).

    (Attachment Link)

Hi everyone, I'm not sure if this would still help, but I want to point out the fact that the runner's uploaded drawing of the bottom plate is incorrect in the four corners. I was able to ask a friend of mine of modify the drawing so that it would fit in the cutout on the bottom, and you can download it below.

Please note that the thickness of the plate is 3mm, and while it was the best my friend could do off of the original drawing, it's still not a 100% fit. I had to shave off 2 corners of the plate a bit further, but the result was more than ok, at least better than having an empty space.

Hey PainMaster, could you please release a fixed weight plate file? Did you have weight plates made for your personal SaiB-CPs?
The plate corner radius in your original file seems to be incorrect. It is about 5.5mm whereas the actual bottom piece weight plate cutout has corner radiuses closer to 10mm.


I'll check this. :)
Fail to purchase GMK Olivia T^T
SaiB-CP Black - Kailh Bronze (Non Click / 58g) - Finish
Light Saver v1 Black - Cherry Wyze Black (Linear / 64g)
Light Saver v2 Gray - Cherry 1501 Black (Linear / 64g)
Light Saver v3 Silver - Cherry 8200 White (Non Click / 64g)
Light Saver Acryl (Duck96 base) - Gateron Yellow (Linear / 62g) - Season 1 Fin.
Octagon v1 Black - Cherry 1501 Black (Linear / 64g) / TX-1800 v1 Red/Black - Cherry Wyze Black (Linear / 58g)
VE.A Test Housing- Cherry 8113 White (Non Click / 58g)
TC-V3 , LZ*ASRH Black, VE.A 2nd
... etc.

Offline PainMaster

  • Formerly cjakma
  • Thread Starter
  • Posts: 152
  • Location: SungNam, south korea
  • IBM(PainMaster)
Re: [GB COMPLETE] SaiB - CP
« Reply #522 on: Mon, 24 June 2019, 20:55:39 »
> 2018-09-28 Update.
   
    SaiB - CP's Bottom weight plate Document Open !

    You can edit it, as long as you specify the source (SaiB - CP).

    (Attachment Link)


It looks like it's going to be tight.
The figures on the drawing are correct.

put up the 0.5mm cut drawings.

* CP_190625_BOTTOM PLATE.zip (36 kB - downloaded 26 times.)

Fail to purchase GMK Olivia T^T
SaiB-CP Black - Kailh Bronze (Non Click / 58g) - Finish
Light Saver v1 Black - Cherry Wyze Black (Linear / 64g)
Light Saver v2 Gray - Cherry 1501 Black (Linear / 64g)
Light Saver v3 Silver - Cherry 8200 White (Non Click / 64g)
Light Saver Acryl (Duck96 base) - Gateron Yellow (Linear / 62g) - Season 1 Fin.
Octagon v1 Black - Cherry 1501 Black (Linear / 64g) / TX-1800 v1 Red/Black - Cherry Wyze Black (Linear / 58g)
VE.A Test Housing- Cherry 8113 White (Non Click / 58g)
TC-V3 , LZ*ASRH Black, VE.A 2nd
... etc.

Offline poolside

  • Posts: 777
  • Location: On the deck
Re: [GB COMPLETE] SaiB - CP
« Reply #523 on: Thu, 27 June 2019, 06:34:38 »
Thanks for taking the time to review the plate file.
If corner radiuses don't match, the weight plate won't fit into the bottom piece cutout (?).

221821-0
221823-1

Online LightningXI

  • * Elevated Elder
  • Posts: 3021
  • Location: New York
  • PPD
    • ArtisanMacro
Re: [GB COMPLETE] SaiB - CP
« Reply #524 on: Thu, 25 July 2019, 08:48:04 »


Thanks for taking the time to review the plate file.
If corner radiuses don't match, the weight plate won't fit into the bottom piece cutout (?).

(Attachment Link)
(Attachment Link)

Did this ever end up being resolved?
WANTED: Clacks, Artisans, Keysets, Vintage Cherry and Other Goodies

More
Quickfire Pro | TADA 68 | Novatouch | Whitefox | Octagon v1 | Blackbird | HHKB Pro 2 | KBD75 | VE.A | X60 | Canoe | HHKB Pro 1 | FJELL | Revo One | ALPS64 | Lightsaver v3 | IBM 5140 WKL | Realforce 87u | MIRA SE | Duck Poker | Canoe | Moon | Weaven | M65-A | EXENT | Wooden Planck | Tokyo60 | Viper v1 | E6-v2 | IBM SSK | CA66 | TX-CP | SINGA | TGR Alice | FJELL R2 | Klippe | JER-A06 | GSKT-00 | M60-A | Realforce 84u | AL1 | Keycult No. 1 | SaiB-CP | G81-3077SAU | DC60 | Realforce 84ub | TMO50 | G80-1800 | Leaf 80 | LZ GH-v2 | T60 | LZ MP | KMAC Happy | TGR-910RE (Al) | TGR-910RE (PC) | SKB60 | UNIKORN | IBM 3278 (pending restoration) | KFE | TGR Jane v2 | TGR Jane v2 CE | Koala | iS0 | Norbatouch | KPad | Xeno | F62 Kishsaver | Keycult No.1/60 Rev. 1 | GSKT-00 Z | Jubi | Montage


Offline poolside

  • Posts: 777
  • Location: On the deck
Re: [GB COMPLETE] SaiB - CP
« Reply #525 on: Thu, 25 July 2019, 16:54:14 »
Not yet, unfortunately. I should ask him again if he can provide that missing measurement.

Offline Vloshko

  • Posts: 165
  • Location: Cali, Colorado, & Israel
Re: [GB COMPLETE] SaiB - CP
« Reply #526 on: Thu, 22 August 2019, 11:48:08 »
224950-0
224952-1
224954-2
Keycap Compendium

Discord: Vloshko#1327

Key Cap Wishlist

2019: Configure Optimal Audio Settings

HHKB Pro 2, Model M, Unicorn X Legend, ESPECTRO 96, SaiB CP, E8-V1.