« previous next »
Pages:  [1]     Go Down

Author Topic: IBM Model F XT: reattaching space bar without taking the whole thing apart  (Read 10730 times)

0 Members and 1 Guest are viewing this topic.

Offline khaangaaroo

  • Thread Starter
  • Posts: 378
  • Location: Los Angeles
IBM Model F XT: reattaching space bar without taking the whole thing apart
« on: Sat, 09 March 2013, 18:06:54 »
I'm new to buckling springs, so I didn't know some boards had stabilizers that are attached to the spacebar before the board is put together, like on my Model F XT. I pulled all my keys off for cleaning, only to realize the space bar would not snap back onto the stabilizers.

I did end up taking the whole board apart to reattach it, but I later thought of an alternate method: Drilling a small hole to loop some string (I used dental floss) to pull the stabilizer forward and into the slot as you're pushing the spacebar down. I removed and reattached the space bar two more times with this method. Worked like a charm! I hope this helps prevent some headaches for some people.



« Last Edit: Sat, 09 March 2013, 18:13:13 by khaangaaroo »
Logged

Offline fohat.digs

  • * Elevated Elder
  • Posts: 6566
  • Location: 35°55'N, 83°53'W
  • weird funny old guy
Re: IBM Model F XT: reattaching space bar without taking the whole thing apart
« Reply #1 on: Sat, 09 March 2013, 20:18:39 »
Good job!

I have done that exact thing several times with the board apart, but never came up with a way to do it from the top.
Logged
"The company [Taylor Farms] made two (2) million-dollar donations: $1 million to the Congressional Leadership Fund, which supports Republican candidates for the U.S. House of Representatives, and $1 million for MAGA Inc, a super PAC that supports Trump.
The $1 million to MAGA Inc was made on March 25, 2025, just just six days after the FDA announced it was delaying the implementation of its “Food Traceability Rule” by 30 months."

Offline zooksman

  • Posts: 7
Re: IBM Model F XT: reattaching space bar without taking the whole thing apart
« Reply #2 on: Sat, 13 May 2017, 22:55:42 »
Just wanted to say thanks for this, 4 years later. I did it today and it worked like a charm.
Logged

Offline MadCow

  • Posts: 1
Re: IBM Model F XT: reattaching space bar without taking the whole thing apart
« Reply #3 on: Sat, 25 June 2022, 20:51:35 »
Thanks for this - I was being a dullard as I thought the space-bar wobble was a "feature".
However,
Further to this I discovered that you don't need to drill a hole. Take some dental floss - you know - the stuff that makes your gums bleed when you use it sometimes - and thread it down the stabilizer hole. As it is wound in a spall it will have a natural tendency to bend at the end. Loop around the stabilizing wire and use (fine nosed) tweezers to pull the end up. Make sure you have a good doubled up length for a good grip. Repeat with other stabilizer wire. Now, making sure the central spring is properly seated, push one end down, trying to angle/rotate it so the notch for the wire is angled open end down-ish (I think this helps...  :rolleyes:) while gripping the dental floss, preventing the stabilizing wire from depressing. The natural flex of the plastic will allow it to clip into place. Repeat other end. Stabilized. Gently pull the dental floss out once happy.
The hole (te-he) process took me 5 minutes.
This may leave some dental floss wax in the well - but - oh well.
Hope this helps.
Logged
Pages:  [1]     Go Up
« previous next »