« previous next »
Pages:  [1]     Go Down

Author Topic: Can't reprogram my GH60  (Read 3772 times)

0 Members and 1 Guest are viewing this topic.

Offline sakai4eva

  • Thread Starter
  • Posts: 281
Can't reprogram my GH60
« on: Thu, 06 August 2015, 12:55:46 »
Hi guys.

I feel like a retard this past week, because a few months ago I upgraded my entire PC but I forgot how I got the drivers for my board.

It's a GH60 Rev_CHN to be exact.

I have managed to install the drivers properly (ATMEGA32U4 shows up in device manager), but every single time the bootloader can't be found.

I'm completely stumped and I feel that I have missed a step or took a few things for granted with my old PC.

Any insight?
Logged

Offline jdcarpe

  • * Curator
  • Posts: 8852
  • Location: Odessa, TX
  • Live long, and prosper.
Re: Can't reprogram my GH60
« Reply #1 on: Thu, 06 August 2015, 13:01:47 »
Did you install Atmel FLIP? What device does it show when you jump into boot loader mode while it's connected to your PC?
Logged
KMAC :: LZ-GH :: WASD CODE :: WASD v2 :: GH60 :: Alps64 :: JD45 :: IBM Model M :: IBM 4704 "Pingmaster"

http://jd40.info :: http://jd45.info


in memoriam
"When I was a kid, I used to take things apart and never put them back together."

Offline sakai4eva

  • Thread Starter
  • Posts: 281
Re: Can't reprogram my GH60
« Reply #2 on: Thu, 06 August 2015, 13:22:59 »
Quote from: jdcarpe on Thu, 06 August 2015, 13:01:47
Did you install Atmel FLIP? What device does it show when you jump into boot loader mode while it's connected to your PC?

http://imgur.com/mQJUl7n

Atmel FLIP installed.
Logged

Offline jdcarpe

  • * Curator
  • Posts: 8852
  • Location: Odessa, TX
  • Live long, and prosper.
Re: Can't reprogram my GH60
« Reply #3 on: Thu, 06 August 2015, 13:24:56 »
Quote from: sakai4eva on Thu, 06 August 2015, 13:22:59
Quote from: jdcarpe on Thu, 06 August 2015, 13:01:47
Did you install Atmel FLIP? What device does it show when you jump into boot loader mode while it's connected to your PC?

http://imgur.com/mQJUl7n

Atmel FLIP installed.

Does the device appear to change after you press the button to jump into bootloader?
Logged
KMAC :: LZ-GH :: WASD CODE :: WASD v2 :: GH60 :: Alps64 :: JD45 :: IBM Model M :: IBM 4704 "Pingmaster"

http://jd40.info :: http://jd45.info


in memoriam
"When I was a kid, I used to take things apart and never put them back together."

Offline sakai4eva

  • Thread Starter
  • Posts: 281
Re: Can't reprogram my GH60
« Reply #4 on: Thu, 06 August 2015, 13:34:52 »
Quote from: jdcarpe on Thu, 06 August 2015, 13:24:56
Quote from: sakai4eva on Thu, 06 August 2015, 13:22:59
Quote from: jdcarpe on Thu, 06 August 2015, 13:01:47
Did you install Atmel FLIP? What device does it show when you jump into boot loader mode while it's connected to your PC?

http://imgur.com/mQJUl7n

Atmel FLIP installed.

Does the device appear to change after you press the button to jump into bootloader?

yeap. Atmel doesn't show up until I press the bootloader button.

EDIT: headed to bed now. 2:40am will try again tomorrow :(
« Last Edit: Thu, 06 August 2015, 13:36:41 by sakai4eva »
Logged

Offline jdcarpe

  • * Curator
  • Posts: 8852
  • Location: Odessa, TX
  • Live long, and prosper.
Re: Can't reprogram my GH60
« Reply #5 on: Thu, 06 August 2015, 13:40:17 »
Oh, do you have WinAVR installed?
Logged
KMAC :: LZ-GH :: WASD CODE :: WASD v2 :: GH60 :: Alps64 :: JD45 :: IBM Model M :: IBM 4704 "Pingmaster"

http://jd40.info :: http://jd45.info


in memoriam
"When I was a kid, I used to take things apart and never put them back together."

Offline sakai4eva

  • Thread Starter
  • Posts: 281
Re: Can't reprogram my GH60
« Reply #6 on: Thu, 06 August 2015, 19:11:30 »
Quote from: jdcarpe on Thu, 06 August 2015, 13:40:17
Oh, do you have WinAVR installed?

IS WinAVR necessary? I'll install that now...
Logged

Offline telnet

  • Posts: 56
  • Location: Vancouver, BC
Re: Can't reprogram my GH60
« Reply #7 on: Sun, 09 August 2015, 11:00:30 »
Quote from: sakai4eva on Thu, 06 August 2015, 19:11:30
Quote from: jdcarpe on Thu, 06 August 2015, 13:40:17
Oh, do you have WinAVR installed?

IS WinAVR necessary? I'll install that now...

I had a similar problem where it would stop at "waiting for bootloader...." stage.
What needed to be done was update the driver of ATm32U4DFU device to a WinUSB version by using Zadig which shipped with the latest version of tkg-toolkit.

After that the firmware flashed without issues.
Logged

QFR Frosty Flake | 7bit Phantom

Offline sakai4eva

  • Thread Starter
  • Posts: 281
Re: Can't reprogram my GH60
« Reply #8 on: Sun, 09 August 2015, 21:36:00 »
Tried installing Zadig by itself, still no dice.

:(
Logged

Offline telnet

  • Posts: 56
  • Location: Vancouver, BC
Re: Can't reprogram my GH60
« Reply #9 on: Mon, 10 August 2015, 02:03:36 »
What do you see when you have zadig running and have the keyboard plugged in and pressed the firmware button?
Logged

QFR Frosty Flake | 7bit Phantom
Pages:  [1]     Go Up
« previous next »