Hello, I have a problem creating the backlight configuration.
I have the keyboard with a led for each switch, in total 93 white leds connected to the Pin B5 (not RGB) (TKL + 5 keys)
I would like to have 3 keys to control the LEDs using PWM,
ON / OFF
Increase
Decrease
This is the configuration of my files. (RAR ->
https://www.dropbox.com/s/jo00qwws0xrnlkr/shiro.rar?dl=0 )
I'm sure there is useless code for my keyboard, since I use Cluepad as an example.
I had not used QMK, but had TMK for my previous custom keyboard
I press the keys I assigned FN1 FN2 FN3 and there is no answer.
config.h#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xC1ED
#define PRODUCT_ID 0x2312
#define DEVICE_VER 0x0001
#define MANUFACTURER Cortes
#define PRODUCT Shiroboard
#define DESCRIPTION QMK keyboard firmware for Shiroboard
/* key matrix size */
#define MATRIX_ROWS 6
#define MATRIX_COLS 17
#define MATRIX_ROW_PINS { F7, F6, F5, F4, F1, F0 }
#define MATRIX_COL_PINS { B4, E6, D7, D6, D4, D5, C7, C6, D3, D2, D1, D0, B7, B3, B2, B1, B0 }
#define UNUSED_PINS
#define DIODE_DIRECTION COL2ROW
#define DEBOUNCING_DELAY 5
#define BACKLIGHT_LEVELS 3
#define BACKLIGHT_PIN B5
#define LOCKING_SUPPORT_ENABLE
#define LOCKING_RESYNC_ENABLE
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
#define ALWAYS_DEBUG
#endif
rules.mkMCU = atmega32u4
F_CPU = 16000000
ARCH = AVR8
F_USB = $(F_CPU)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
OPT_DEFS += -DBOOTLOADER_SIZE=4096
BOOTMAGIC_ENABLE ?= yes
# MOUSEKEY_ENABLE ?= no
# EXTRAKEY_ENABLE ?= no
# CONSOLE_ENABLE ?= no
# COMMAND_ENABLE ?= no
NKRO_ENABLE ?= no
BACKLIGHT_ENABLE ?= yes
#RGBLIGHT_ENABLE ?= no
# MIDI_ENABLE ?= no
# UNICODE_ENABLE ?= no
# BLUETOOTH_ENABLE ?= no
shiro.c#include "shiro.h"
int pwm_level;
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
// JTAG disable for PORT F. write JTD bit twice within four cycles.
MCUCR |= (1<<JTD);
MCUCR |= (1<<JTD);
};
void led_set_kb(uint8_t usb_led)
{
print("led_set\n");
}
void backlight_init_ports(void)
{
// Set C7 to output
DDRB |= (1<<5);
// Initialize the timer
TC4H = 0x03;
OCR4B = 0xFF;
TCCR4A = 0b10000010;
TCCR4B = 0b00000001;
}
void backlight_set(uint8_t level)
{
// Determine the PWM level
switch (level)
{
case 0:
// 33%
pwm_level = 0x54;
break;
case 1:
// 66%
pwm_level = 0xA8;
break;
case 2:
// 100%
pwm_level = 0xFF;
break;
case 3:
// 0%
pwm_level = 0x00;
break;
default:
xprintf("Unknown level: %d\n", level);
}
// Write the PWM level to the timer
TC4H = pwm_level >> 8;
OCR4B = 0xFF & pwm_level;
}
shiro.h#ifndef SHIRO_H
#define SHIRO_H
#include "quantum.h"
#define KEYMAP( \
K0A, K0C, K0D, K0E, K0F, K0G, K0H, K0I, K0J, K0K, K0L, K0M, K0N, K0O, K0P, K0Q, \
K1A, K1B, K1C, K1D, K1E, K1F, K1G, K1H, K1I, K1J, K1K, K1L, K1M, K1N, K1O, K1P, K1Q, \
K2A, K2B, K2C, K2D, K2E, K2F, K2G, K2H, K2I, K2J, K2K, K2L, K2M, K2N, K2O, K2P, K2Q, \
K3A, K3B, K3C, K3D, K3E, K3F, K3G, K3H, K3I, K3J, K3K, K3L, K3M, K3O, K3P, K3Q, \
K4A, K4B, K4C, K4D, K4E, K4F, K4G, K4H, K4I, K4J, K4K, K4L, K4M, K4O, K4P, K4Q, \
K5A, K5B, K5C, K5G, K5K, K5L, K5M, K5N, K5O, K5P, K5Q \
) { \
{ K0A, KC_NO,K0C, K0D, K0E, K0F, K0G, K0H, K0I, K0J, K0K, K0L, K0M, K0N, K0O, K0P, K0Q }, \
{ K1A, K1B, K1C, K1D, K1E, K1F, K1G, K1H, K1I, K1J, K1K, K1L, K1M, K1N, K1O, K1P, K1Q }, \
{ K2A, K2B, K2C, K2D, K2E, K2F, K2G, K2H, K2I, K2J, K2K, K2L, K2M, K2N, K2O, K2P, K2Q }, \
{ K3A, K3B, K3C, K3D, K3E, K3F, K3G, K3H, K3I, K3J, K3K, K3L, K3M, KC_NO, K3O, K3P, K3Q }, \
{ K4A, K4B, K4C, K4D, K4E, K4F, K4G, K4H, K4I, K4J, K4K, K4L, K4M, KC_NO, K4O, K4P, K4Q }, \
{ K5A, K5B, K5C, KC_NO,KC_NO,KC_NO,K5G, KC_NO,KC_NO,KC_NO,K5K, K5L, K5M, K5N, K5O, K5P, K5Q } \
}
#endif
keymap.c#include "shiro.h"
#include "backlight.h"
#define _BL 0
#define _FL 1
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[_BL] = KEYMAP(
KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME,KC_PGUP, \
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_ENT, KC_DEL, KC_END, KC_PGDN, \
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_NUHS, KC_FN2, KC_FN1, KC_TRNS, \
KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, KC_FN3, KC_UP, KC_TRNS, \
KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT,KC_FN0, KC_TRNS, KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT),
[_FL] = KEYMAP(
KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME,KC_PGUP, \
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_ENT, KC_DEL, KC_END, KC_PGDN, \
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_NUHS, KC_FN2, KC_FN1, KC_TRNS, \
KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, KC_FN3, KC_UP, KC_TRNS, \
KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT,KC_FN0, KC_TRNS, KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT),
};
/*enum function_id {
};*/
const uint16_t PROGMEM fn_actions[] = {
[0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay
[1] = ACTION_BACKLIGHT_TOGGLE(),
[2] = ACTION_BACKLIGHT_INCREASE(),
[3] = ACTION_BACKLIGHT_DECREASE(),
};
