« previous next »
Pages:  [1]     Go Down

Author Topic: IBM 1397000 Not Working  (Read 3128 times)

0 Members and 1 Guest are viewing this topic.

Offline Shadow Lord

  • Thread Starter
  • Posts: 5
IBM 1397000 Not Working
« on: Mon, 30 April 2018, 19:26:13 »
Hello Everyone,

Long time lurker - new poster.

I am owner of a very clean IBM 1397000 Model M 122Key Terminal Keyboard that I am trying to use with a Soarer Convertor. Unfortunately, this KB has a number of issues. The first was a bad flexy wire to the LED light PCB. I managed to hack my own cable for that and have the lights working. The second more serious problem is the bottom row of function keys (F1 - F12).

In that row only F1, F4, F7, and F10 work (yep every third key). All other keys on the KB work fine. The keys mechanically feel fine but they do not produce any scan codes (according to HID_Listen). I have resat the keys and resat the flexy cable with no change in behavior. I found another thread https://geekhack.org/index.php?topic=16190.msg323544#msg323544 that makes a reference to a thread with info on the membrane contact sheet. Unfortunately, the post it references seems to be gone. If anyone has the info on membrane sheet, trouble shooting, or fixes I am all ears!

Is this KB salvageable (not just for parts I mean ;)). Or is it pretty much a done deal? TIA!
Logged

Offline E TwentyNine

  • Posts: 884
    • Some of My Keyboards
Re: IBM 1397000 Not Working
« Reply #1 on: Mon, 30 April 2018, 21:59:21 »
The usual...a broken trace.   Take a closer look, it's likely near where the membrane "turns into" the plug-in ribbon.
Logged
Daily driver: SSK or Tenkeyless IBM AT
1984 Model M Industrial Prototype ⌨ 1992 Black Oval Industrial SSK ⌨ 1982 5251 Beam Spring ⌨ 89 Key "SSK" ⌨ M13 triplets

Offline Shadow Lord

  • Thread Starter
  • Posts: 5
Re: IBM 1397000 Not Working
« Reply #2 on: Mon, 30 April 2018, 22:40:47 »
Quote from: E TwentyNine on Mon, 30 April 2018, 21:59:21
The usual...a broken trace.   Take a closer look, it's likely near where the membrane "turns into" the plug-in ribbon.

I figured as much but I was hoping to be able to better localize it. Also, the pattern is a bit weird - after all if one trace was broken would it create a pattern of broken keys every third one? And if more then one trace gone wouldn't you expect more keys not to work?

M<ore importantly can the trace be corrected? Or does it need to be replaced?

TIA!
Logged

Offline E TwentyNine

  • Posts: 884
    • Some of My Keyboards
Re: IBM 1397000 Not Working
« Reply #3 on: Tue, 01 May 2018, 10:34:07 »
It's been a while since I've looked at a 122 membrane, but I'm fairly certain the F keys have at least one dedicated trace and it follows that kind of a pattern (2 keys, skip, 2 keys..).  It's easily fixable if it's outside of the assembly, either via conductive tape or glue or a combination.
Logged
Daily driver: SSK or Tenkeyless IBM AT
1984 Model M Industrial Prototype ⌨ 1992 Black Oval Industrial SSK ⌨ 1982 5251 Beam Spring ⌨ 89 Key "SSK" ⌨ M13 triplets

Offline Shadow Lord

  • Thread Starter
  • Posts: 5
Re: IBM 1397000 Not Working
« Reply #4 on: Tue, 01 May 2018, 10:46:32 »
Quote from: E TwentyNine on Tue, 01 May 2018, 10:34:07
It's been a while since I've looked at a 122 membrane, but I'm fairly certain the F keys have at least one dedicated trace and it follows that kind of a pattern (2 keys, skip, 2 keys..).  It's easily fixable if it's outside of the assembly, either via conductive tape or glue or a combination.

Does anyone have the PDF that shows the membrane layout for the 122 keys? Unfortunately, the thread it was in seems to be gone (unless I am doing something wrong). The controller PCB has three flex connectors.

1. wide one which seems to be for the main KB
2. a smaller one that controls the function keys (disconnecting this keeps any of the function keys from working)
3. and one to the LED PCB

The one going to the function keys has six wires on it and I think I see a break in one of the lines but I am not sure if that is it or not. Where can I get conductive tape to test it out (any particular brand) or is there an easy way to test it beforehand? Thanks.
Logged

Offline ag36

  • Posts: 179
  • Location: London, UK
Re: IBM 1397000 Not Working
« Reply #5 on: Wed, 02 May 2018, 14:36:01 »
Use a multimeter to do continuity test, just pick the cheapest one with continuity function?
Logged
Model M*5, SSK*4, M13 black*1, Model F XT*1, AT*1 F107*1, Unicomp*1, 3278 *1, Leopold FC750R*2, 980M*2 FC980C*1 Filco majestouch 2 TKL*1, Cooler Master MasterKeys S PBT*1, Uniqey Q100*2, Ducky pocket*1, KBD75*2, KBD19X*2, HHKB pro 2*1, Type-S*1 Topre Realforce RGB*1, 108 all 30g*1, numpad*1, 87U*1 Dell AT101W*2, Alps64*2, V80 matias quiet click*2, Quiet liner *1, WYSE ASCII *1

Offline E TwentyNine

  • Posts: 884
    • Some of My Keyboards
Re: IBM 1397000 Not Working
« Reply #6 on: Wed, 02 May 2018, 14:54:06 »
Quote from: Shadow Lord on Tue, 01 May 2018, 10:46:32

Does anyone have the PDF that shows the membrane layout for the 122 keys? Unfortunately, the thread it was in seems to be gone (unless I am doing something wrong). The controller PCB has three flex connectors.

1. wide one which seems to be for the main KB
2. a smaller one that controls the function keys (disconnecting this keeps any of the function keys from working)
3. and one to the LED PCB

The one going to the function keys has six wires on it and I think I see a break in one of the lines but I am not sure if that is it or not. Where can I get conductive tape to test it out (any particular brand) or is there an easy way to test it beforehand? Thanks.

That's not how they work.

The wide one is for the keyboard columns.  Narrow one is for rows.  (Generally speaking, the F keys on the 122 kinda screw with this, but that's the idea).

Apart from a continuity test, an easy way to test is to get a strand of wire and bridge where you think the break is, and try the keys.  Near the connector the membrane has a coating so make sure you're testing where you can actually contact the trace.
Logged
Daily driver: SSK or Tenkeyless IBM AT
1984 Model M Industrial Prototype ⌨ 1992 Black Oval Industrial SSK ⌨ 1982 5251 Beam Spring ⌨ 89 Key "SSK" ⌨ M13 triplets

Offline Shadow Lord

  • Thread Starter
  • Posts: 5
Re: IBM 1397000 Not Working
« Reply #7 on: Thu, 03 May 2018, 16:29:39 »
So I got some conductive tape and tried repairing the cable. As I did not want to break the plastic rivets I focused on the PCB connector end of the cable. Unfortunately, there is no change in behavior. Those 8 keys out of 122 still are not working.

I then tried repairing the LED cable since that was easily accessible:

194996-0" alt="" class="bbc_img" />

On the repaired wire I am still unable to get continuity. So if something is going on it seems to be in the middle of the wire (under the mylar sheets) or I am missing something simple but significant. Any help/pointers/ideas? TIA!
« Last Edit: Thu, 03 May 2018, 16:31:18 by Shadow Lord »
Logged

Offline ag36

  • Posts: 179
  • Location: London, UK
Re: IBM 1397000 Not Working
« Reply #8 on: Fri, 11 May 2018, 11:50:33 »
Maybe get a new membrane from Unicomp?
Logged
Model M*5, SSK*4, M13 black*1, Model F XT*1, AT*1 F107*1, Unicomp*1, 3278 *1, Leopold FC750R*2, 980M*2 FC980C*1 Filco majestouch 2 TKL*1, Cooler Master MasterKeys S PBT*1, Uniqey Q100*2, Ducky pocket*1, KBD75*2, KBD19X*2, HHKB pro 2*1, Type-S*1 Topre Realforce RGB*1, 108 all 30g*1, numpad*1, 87U*1 Dell AT101W*2, Alps64*2, V80 matias quiet click*2, Quiet liner *1, WYSE ASCII *1

Offline Shadow Lord

  • Thread Starter
  • Posts: 5
Re: IBM 1397000 Not Working
« Reply #9 on: Sun, 13 May 2018, 18:35:27 »
Quote from: ag36 on Fri, 11 May 2018, 11:50:33
Maybe get a new membrane from Unicomp?

Yeah too much work, hassle, and expense for the KB.
Logged

Offline Snowdog993

  • Grace Under Pressure
  • Posts: 1587
  • Location: Over There! (Pointing)
  • Justifiably Clueless.
Re: IBM 1397000 Not Working
« Reply #10 on: Sun, 13 May 2018, 21:16:17 »
Quote from: Shadow Lord on Sun, 13 May 2018, 18:35:27
Quote from: ag36 on Fri, 11 May 2018, 11:50:33
Maybe get a new membrane from Unicomp?

Yeah too much work, hassle, and expense for the KB.

Unless you have it professionally fixed.

https://imgur.com/a/tIonH

That might be a consideration.
Logged
Pages:  [1]     Go Up
« previous next »