[Postoned] FingerSK/UP (75%) + Finger (65%) Cases in development

[meiosis]

Orders postponed until an ETA is given on case and plate development, sorry everyone.


If someone really wanted their orders of just pcbs please resubmit!

Form:
http://goo.gl/forms/d6xHdDdVTE

[sethk_]

Yep, 15$ includes all parts!

[Data]

If we purchase the RGB version will the RGB LEDs also come soldered like the controller parts?

@sethk_ Can you expand on the extent of soldering services you're providing?  I'm trying to figure out if that's something I need.

Forgive me, this was probably asked and answered in the IC thread but I'm not seeing it.

[geniekid]

The OP could use more details.  We should not assume everyone interested in this GB has read through the IC.

Do the PCBs include unsoldered diodes and/or resistors?  If not, what diodes or resistors are needed?

What layouts does the FingerSK support?

What is a "Panda design"?  Is this an option that will be added later to the order form?

[Norman_the_Owl]

How are the RGB SMD leds controlled? Are they controlled at all? What comes presoldered? Any diodes, resistors, etc?

[sethk_]

If we purchase the RGB version will the RGB LEDs also come soldered like the controller parts?

@sethk_ Can you expand on the extent of soldering services you're providing?  I'm trying to figure out if that's something I need.

Forgive me, this was probably asked and answered in the IC thread but I'm not seeing it.

I offer soldering services in a thread I have, and for this GB I will be offering Resistors & Diodes, but if you are requesting more than just that, PM me and we can work out the details. My thread can be seen here: https://geekhack.org/index.php?topic=73610

The OP could use more details.  We should not assume everyone interested in this GB has read through the IC.

Do the PCBs include unsoldered diodes and/or resistors?  If not, what diodes or resistors are needed?

What layouts does the FingerSK support?

What is a "Panda design"?  Is this an option that will be added later to the order form?

It does not include parts for diodes and resistors.
These are the diodes you will need: http://www.mouser.com/Search/ProductDetail.aspx?R=1N4148W-7-Fvirtualkey62110000virtualkey621-1N4148W-F
And resistors come in different Ohms, but this is the general type, and you can find other Ohms: http://www.mouser.com/Search/ProductDetail.aspx?R=ERJ-6ENF8060Vvirtualkey66720000virtualkey667-ERJ-6ENF8060V

Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide
Leeku's new PCBs all support similar layout options.

How are the RGB SMD leds controlled? Are they controlled at all? What comes presoldered? Any diodes, resistors, etc?

Only controller parts come Presoldered AFAIK, not sure about RGB LEDs. For 15$, I am offering a service where I will solder on the diodes & resistors. If you need more than just that for assembly, you can see my thread where I posted it earlier in this post.

[tjweir]

Are there any finished examples of the FingerUP 65%?

[sethk_]

Are there any finished examples of the FingerUP 65%?

This is the one that is used inside LZ SQs I believe

[tjweir]

Are there any finished examples of the FingerUP 65%?

This is the one that is used inside LZ SQs I believe

Ah yes, I believe you mentioned that in another thread, I forgot.

Thanks!

[geniekid]

If we purchase the RGB version will the RGB LEDs also come soldered like the controller parts?

@sethk_ Can you expand on the extent of soldering services you're providing?  I'm trying to figure out if that's something I need.

Forgive me, this was probably asked and answered in the IC thread but I'm not seeing it.

I offer soldering services in a thread I have, and for this GB I will be offering Resistors & Diodes, but if you are requesting more than just that, PM me and we can work out the details. My thread can be seen here: https://geekhack.org/index.php?topic=73610

The OP could use more details.  We should not assume everyone interested in this GB has read through the IC.

Do the PCBs include unsoldered diodes and/or resistors?  If not, what diodes or resistors are needed?

What layouts does the FingerSK support?

What is a "Panda design"?  Is this an option that will be added later to the order form?

It does not include parts for diodes and resistors.
These are the diodes you will need: http://www.mouser.com/Search/ProductDetail.aspx?R=1N4148W-7-Fvirtualkey62110000virtualkey621-1N4148W-F
And resistors come in different Ohms, but this is the general type, and you can find other Ohms: http://www.mouser.com/Search/ProductDetail.aspx?R=ERJ-6ENF8060Vvirtualkey66720000virtualkey667-ERJ-6ENF8060V

Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide
Leeku's new PCBs all support similar layout options.

How are the RGB SMD leds controlled? Are they controlled at all? What comes presoldered? Any diodes, resistors, etc?

Only controller parts come Presoldered AFAIK, not sure about RGB LEDs. For 15$, I am offering a service where I will solder on the diodes & resistors. If you need more than just that for assembly, you can see my thread where I posted it earlier in this post.

Thanks for the info sethk

[tjweir]

Form submitted for a FingerUP.

The bottom row layout options sealed the deal for me.

Squeee.

[meiosis]

Hey everyone, was pretty busy today, Diodes and Resistors are not included, if they are needed I can source them and include 100x with each order for a bit more.

More photos will be added tonight or tomorrow!

The $5 RGB chip will come soldered on

[tjweir]

Hey everyone, was pretty busy today, Diodes and Resistors are not included, if they are needed I can source them and include 100x with each order for a bit more.

More photos will be added tonight or tomorrow!

The $5 RGB chip will come soldered on

I asked for sethk_ to assemble my FingerUP, so I'll need those parts.

[JonasDK]

i'd be in for sure if there's a case and plate made made for it.

We are in talks, there might be an acrylic case option!

What's the status with the case?

[AKmalamute]

What's the status with the case?

 From the look of it, (I'm in for the FC660M looking 'fingerup') two pieces of acrylic would be more than adequate but I'd need the .DXFs to go that route.

 Actually, speaking of the DIY case route Meiosis, can you find out if a metal "rim" would be a problem? That is, let's say you were to get an aluminum layered case ... would it short anything out if the "acrylic" case were made of metal (e.g. cut by big blue saw)?

[thelectronicnub]

In for a FingerSK, and definitely interested in an acrylic case

[ika]

How long will this buy be running? I would like to wait and see what case options will be made available, if any. Very interested in the 75% though.

[meiosis]

In for a FingerSK, and definitely interested in an acrylic case

I will try my best to make this happen, I just want to make sure it's a reasonable price since I have no idea how many people would be interested in a whole set. (I'm guessing 10-20) Although I believe the MXmini files are out there, and would just need an acrylic cutter. (read below on why I  haven't mentioned it completely!)

What's the status with the case?

 From the look of it, (I'm in for the FC660M looking 'fingerup') two pieces of acrylic would be more than adequate but I'd need the .DXFs to go that route.

 Actually, speaking of the DIY case route Meiosis, can you find out if a metal "rim" would be a problem? That is, let's say you were to get an aluminum layered case ... would it short anything out if the "acrylic" case were made of metal (e.g. cut by big blue saw)?

It won't, there aren't any traces near the area, and the traces are covered .

How long will this buy be running? I would like to wait and see what case options will be made available, if any. Very interested in the 75% though.

Cases are still being discussed, I will try to run it by someone who has made them before... As for affordability of the cases I don't know what MOQ would be feasible so I have been skeptical to give an exact answer to whether they will be an option.

The GB will finish 9/12 (or before)

[tjweir]

I think I want to update my order from 1 FingerUP with assembly to 2.

Should I simply resubmit the form?

[Cameron]

I'm only going in if there's a case option unless anyone knows of any existing cases that will fit this on taobao or anything

[Data]

Plates and cases were tossed around in the Interest Check.

I'm still deciding if I want to get in on this...

[Invaderevan]

I <3 75%!
In for 2! I would buy diodes if you wanted to sell them to me!

[Norman_the_Owl]

Also waiting for possible case/plate options

I'll probably be in for a FingerUp anyway, but no sense hopping in too early

[gogusrl]

Split spacebar but no ISO ?

[meiosis]

If anyone wants to change their order just submit another one! I'll go through and just use the most current!

[tjweir]

If anyone wants to change their order just submit another one! I'll go through and just use the most current!

Thanks.

[tjweir]

Do we know what controller this uses?

All of the firmware stuff I've seen about Leeku boards is Windows-only, if so, this is going to be a problem.

If it uses an ATMEL atmega32XX maybe I can port tmk from @hasu.

[sethk_]

Split spacebar but no ISO ?

theres ISO

[meiosis]

Do we know what controller this uses?

All of the firmware stuff I've seen about Leeku boards is Windows-only, if so, this is going to be a problem.

If it uses an ATMEL atmega32XX maybe I can port tmk from @hasu.

How complicated is the key mapping you are planning, if you would like I could flash it to your preferred layout or hot keys. You are ordering assembly
Too? From the form haha

[tjweir]

Do we know what controller this uses?

All of the firmware stuff I've seen about Leeku boards is Windows-only, if so, this is going to be a problem.

If it uses an ATMEL atmega32XX maybe I can port tmk from @hasu.

How complicated is the key mapping you are planning, if you would like I could flash it to your preferred layout or hot keys. You are ordering assembly
Too? From the form haha

The current plan is pretty complicated, I'll get the link to the layout.

Two? One for work, one for home, only baller status for me. 

[meiosis]

Woops I was on my phone and hit return , I meant you were having it assembled by seth? And ahh if it's custom I understand that it has to be exactly as you want.


As for everyone else would a full acrylic or skin case be preferred? (Still hypothetical)

[meiosis]

As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.

[Jokrik]

As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.

Would be very interested if there's a case and plate with it (75%)
keep us updated!

[meiosis]

As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.

Would be very interested if there's a case and plate with it (75%)
keep us updated!

Yeah one thing I can say though which might deter but instead of raising hopes, is it will be mostly acrylic.

[Norman_the_Owl]

As of now I believe there will be plates available although there will be screw holes if there was a case, perhaps I started the gb a bit too early, but things are looking up.

Not too early, just let it run for a while longer if necessary. It lets orders come in over time. And gives my wallet time to prepare

I just shelled out for some round 5a caps, god knows i need the recovery time

[thelectronicnub]

Would a Winkeyless B.mini case be compatible with this?

[sethk_]

Would a Winkeyless B.mini case be compatible with this?

Yes

[hippo008]

Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.

My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?

[meiosis]

Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.

My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?

Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housing



this might be happening..

[E3E]

My wallet is on lock down for the most part. Only a few more things I have left to buy to fulfill some board projects I have. As much as I wish I could slot this in, it'd just be redundant. I can't justify it. Tjweir IS a baller though. )

That LZ tho. 

[ika]

oh no... I did not need to see that... and if there is a 65% option like this, I expect a chorus of tears from every bank account I have.

[tjweir]

oh no... I did not need to see that... and if there is a 65% option like this, I expect a chorus of tears from every bank account I have.

Ya, down for that tub case for a 65% if possible. 

[stoic-lemon]

A case would make this 65% very difficult to pass up.

[hippo008]

Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.

My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?

Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housing

Show Image

this might be happening..

That would be awesome! And if anybody is interested, I've been looking for a project recently. I'd be happy to work on the files for having a case and plate cut for the FingerUP 65%

[Dreamre]

Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.

My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?

Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housing

Show Image

this might be happening..

What kind of case material is that?

[JonasDK]

Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide
Leeku's new PCBs all support similar layout options.

Wait, so this board wont support ISO?

[sethk_]

Layout and assembly guide: http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide
Leeku's new PCBs all support similar layout options.

Wait, so this board wont support ISO?

It does, I don't think that guide shows it though

[hippo008]

I had some free time so I made up a plate and visual mockup for the FingerUP.



The R4 layout I chose -


Le plate for said layout -


Link to CAD file for plate - https://drive.google.com/file/d/0B-w0V8tjga_QbTJ5SkE0M2E4c0E/view?usp=sharing


Visual Mockup featuring the Carbon set -

[Cameron]

Seriously interested in the FingerUP. Here I was sitting at home trying to cram arrow keys into a 60% I was planning and this comes along! Perfect.

My only question is on case compatability. I'm assuming we have to have our own plates and cases cut?

Not to get anyones hopes up but...
http://kbdlab.co.kr/index.php?document_srl=2640505&mid=board_housing

Show Image

this might be happening..

You seriously have my attention sir. Make it happen. LET ME GIVE YOU MONEY

[ika]

Is there more info about the capabilities or pictures of these PCBs? I found the LZ-SQ here (http://lzlife.tistory.com/entry/Finger-L3-PCB-assembly-guide) and more detail about the FingerUP (or Finger L3?) but can't find much detail on the FingerSK.