« previous next »
Pages:  [1]     Go Down

Author Topic: Pro Micro help and tips for Model F AT  (Read 3189 times)

0 Members and 1 Guest are viewing this topic.

Offline fohat.digs

  • * Elevated Elder
  • Thread Starter
  • Posts: 6565
  • Location: 35°55'N, 83°53'W
  • weird funny old guy
Pro Micro help and tips for Model F AT
« on: Wed, 23 September 2015, 22:13:45 »
I have a Pro Micro breakout board and I would like to install it in an F AT to re-map some keys.

The Soarer's/Teensy thing has worked like a charm and I have done it several times, but I am completely lost with this new thing.

Can anybody give me a quick walk-through on how to do it?

I know that there have been discussions but I can't seem to find them. I will need details, I am better with a hammer and a drill than with programming.
Logged
"We are on the precipice of signing an agreement to advance talks with Iran that preserves the good parts of former President Barack Obama’s Joint Comprehensive Plan of Action (JCPOA) while amplifying its flaws.
Mr. Obama came to an agreement that did not involve America’s most precious treasure, the lives and limbs of our soldiers.  The 1.7 billion dollars of frozen Iranian assets released by Obama pales in comparison to the 300 billion being floated as a rebuilding fund.
So far, speculation that Iran will be free in the future to continue its nuclear program is the opposite of Trump’s stated goal for the war and in direct opposition to what Mr. Obama negotiated."
- Bill Roberts 2026-06-17

Offline SpAmRaY

  • NOT a Moderator
  • * Certified Spammer
  • Posts: 14665
  • Location: ¯\(°_o)/¯
  • because reasons.......
Re: Pro Micro help and tips for Model F AT
« Reply #1 on: Wed, 23 September 2015, 22:18:22 »
Logged

Offline umeboshi

  • Posts: 39
Re: Pro Micro help and tips for Model F AT
« Reply #2 on: Thu, 24 September 2015, 00:58:04 »
This helped me out also when I compiled and burned the wrong image onto the pro micro...

https://geekhack.org/index.php?topic=63227.msg1483033#msg1483033

Logged

Offline jorgenslee

  • Posts: 369
  • Location: Philippines
Re: Pro Micro help and tips for Model F AT
« Reply #3 on: Thu, 24 September 2015, 02:55:34 »
The tricky part with Pro Micro is that after you short the Ground and Reset, you only have 8 seconds to flash the firmware.
Logged

Offline ShawnMeg

  • Posts: 144
  • Location: Parts Unknown
Re: Pro Micro help and tips for Model F AT
« Reply #4 on: Thu, 24 September 2015, 22:39:57 »
Quote from: fohat.digs on Wed, 23 September 2015, 22:13:45
I have a Pro Micro breakout board and I would like to install it in an F AT to re-map some keys.

The Soarer's/Teensy thing has worked like a charm and I have done it several times, but I am completely lost with this new thing.

Can anybody give me a quick walk-through on how to do it?

I know that there have been discussions but I can't seem to find them. I will need details, I am better with a hammer and a drill than with programming.

Fohat,

Did you get this figured out?  It helps if you have some Linux command line experience.  It isn't too difficult, but if you haven't done it before, it can look confusing.  I installed avrdude with Crosspak on an old Mac.  You can PM me if you'd like.
Logged


IBM Model F122 X 2 internal Soarer's || IBM Model M122 internal Soarer's || AEK II SKCM Salmon ALPS external adb_usb converter ||  AEK M0115 SKCM Orange ALPS click mod external adb_usb converter || AEK M0115 SKCM Salmon ALPS external adb_usb converter ||

Offline fohat.digs

  • * Elevated Elder
  • Thread Starter
  • Posts: 6565
  • Location: 35°55'N, 83°53'W
  • weird funny old guy
Re: Pro Micro help and tips for Model F AT
« Reply #5 on: Fri, 25 September 2015, 12:48:02 »
Quote from: ShawnMeg on Thu, 24 September 2015, 22:39:57
Did you get this figured out? 

It helps if you have some Linux command line experience.  It isn't too difficult, but if you haven't done it before, it can look confusing.

No, I gave up. I have a bit of Linux command line experience, but not any kind of deep understanding.

My unit seems to be different from what was described elsewhere. And the voltage marking on the rear seems ambiguous, too.

Logged
"We are on the precipice of signing an agreement to advance talks with Iran that preserves the good parts of former President Barack Obama’s Joint Comprehensive Plan of Action (JCPOA) while amplifying its flaws.
Mr. Obama came to an agreement that did not involve America’s most precious treasure, the lives and limbs of our soldiers.  The 1.7 billion dollars of frozen Iranian assets released by Obama pales in comparison to the 300 billion being floated as a rebuilding fund.
So far, speculation that Iran will be free in the future to continue its nuclear program is the opposite of Trump’s stated goal for the war and in direct opposition to what Mr. Obama negotiated."
- Bill Roberts 2026-06-17

Offline jorgenslee

  • Posts: 369
  • Location: Philippines
Re: Pro Micro help and tips for Model F AT
« Reply #6 on: Fri, 25 September 2015, 22:26:08 »
Quote from: fohat.digs on Fri, 25 September 2015, 12:48:02
Quote from: ShawnMeg on Thu, 24 September 2015, 22:39:57
Did you get this figured out? 

It helps if you have some Linux command line experience.  It isn't too difficult, but if you haven't done it before, it can look confusing.

No, I gave up. I have a bit of Linux command line experience, but not any kind of deep understanding.

My unit seems to be different from what was described elsewhere. And the voltage marking on the rear seems ambiguous, too.

My pro micro is just like that except with the "Deek-Robot" label in the back. When you plug it in, what LEDs are lighting up?
Logged

Offline fohat.digs

  • * Elevated Elder
  • Thread Starter
  • Posts: 6565
  • Location: 35°55'N, 83°53'W
  • weird funny old guy
Re: Pro Micro help and tips for Model F AT
« Reply #7 on: Sat, 26 September 2015, 09:32:14 »
Quote from: jorgenslee on Fri, 25 September 2015, 22:26:08
My pro micro is just like that except with the "Deek-Robot" label in the back. When you plug it in, what LEDs are lighting up?

I get one solid red near the micro-USB socket and a green one at the other end blinks a couple of times.
Logged
"We are on the precipice of signing an agreement to advance talks with Iran that preserves the good parts of former President Barack Obama’s Joint Comprehensive Plan of Action (JCPOA) while amplifying its flaws.
Mr. Obama came to an agreement that did not involve America’s most precious treasure, the lives and limbs of our soldiers.  The 1.7 billion dollars of frozen Iranian assets released by Obama pales in comparison to the 300 billion being floated as a rebuilding fund.
So far, speculation that Iran will be free in the future to continue its nuclear program is the opposite of Trump’s stated goal for the war and in direct opposition to what Mr. Obama negotiated."
- Bill Roberts 2026-06-17

Offline umeboshi

  • Posts: 39
Re: Pro Micro help and tips for Model F AT
« Reply #8 on: Wed, 30 September 2015, 03:00:22 »
Quote from: fohat.digs on Sat, 26 September 2015, 09:32:14
I get one solid red near the micro-USB socket and a green one at the other end blinks a couple of times.

Is it able to go into bootloader mode?  (short RST+GND twice as it boots).  For me the sign that it did is the Product id changes (you can see it via dmesg) - on my pro micro, normal boot the id is "8036" and in bootloader mode it shows up with id of "0036".  8 seconds later it'll go back to "8036".  If it can go into bootloader mode then you can just quickly flash it...
Logged
Pages:  [1]     Go Up
« previous next »