Author Topic: [GB] SPACE65 | 65% Custom Keyboard(GB END)  (Read 15957 times)

WifeIsGoddess and 4 Guests are viewing this topic.

Offline AIRPOTTER

  • Thread Starter
  • Posts: 275
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #50 on: Mon, 31 December 2018, 07:01:09 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 spli.


This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
« Last Edit: Mon, 31 December 2018, 07:40:28 by AIRPOTTER »
INS:https://www.instagram.com/graystudio01/
discord:https://discord.gg/ckeXNRr
Reddit:Graystudio
imgur:graystudio01
slack:graystudio.slack.com

Offline beekey

  • Posts: 159
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #51 on: Mon, 31 December 2018, 07:04:22 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
I think thw images do not show the final plate, as he said they support split space and none of the plates shows this.

Offline AIRPOTTER

  • Thread Starter
  • Posts: 275
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #52 on: Mon, 31 December 2018, 07:30:36 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
I think thw images do not show the final plate, as he said they support split space and none of the plates shows this.
please look at these two pictures. I did a simple test to split space【2.25-1.25-2.75】
This is with switch;

This is with keycap.

I hope I can help you out.
« Last Edit: Mon, 31 December 2018, 07:32:17 by AIRPOTTER »
INS:https://www.instagram.com/graystudio01/
discord:https://discord.gg/ckeXNRr
Reddit:Graystudio
imgur:graystudio01
slack:graystudio.slack.com

Offline beekey

  • Posts: 159
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #53 on: Mon, 31 December 2018, 07:40:14 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
Cool, thanks. This looks good!

Offline AIRPOTTER

  • Thread Starter
  • Posts: 275
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #54 on: Mon, 31 December 2018, 07:42:08 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
Cool, thanks. This looks good!
Thank you for your enjoyment!
These are all things I should do. ;)
INS:https://www.instagram.com/graystudio01/
discord:https://discord.gg/ckeXNRr
Reddit:Graystudio
imgur:graystudio01
slack:graystudio.slack.com

Offline mkarlsson

  • Posts: 272
  • Location: Spain
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #55 on: Mon, 31 December 2018, 07:42:28 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk


Offline AIRPOTTER

  • Thread Starter
  • Posts: 275
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #56 on: Mon, 31 December 2018, 07:56:34 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk
Welcome to enjoy with SPACE65!
INS:https://www.instagram.com/graystudio01/
discord:https://discord.gg/ckeXNRr
Reddit:Graystudio
imgur:graystudio01
slack:graystudio.slack.com

Offline SlamMakanen

  • Posts: 26
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #57 on: Mon, 31 December 2018, 09:03:32 »
Thanks for fixing the ISO split left shift!


Sent from my iPhone using Tapatalk

Offline Mystogan

  • Posts: 7
  • Location: London, UK
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #58 on: Mon, 31 December 2018, 09:41:25 »
Thanks for the quick resolution of the ISO split left shift.

Now to pick a colour scheme...

Online ZyBeR

  • Posts: 36
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #59 on: Mon, 31 December 2018, 10:13:23 »
It would be nice if we could upgrade to brass and not having to buy it as extras.

Online pixelpusher

  • Formerly known as reececonrad
  • Posts: 2463
  • Location: Tennessee - USA
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #60 on: Mon, 31 December 2018, 10:30:01 »
Having typed on a carbon fiber plate before, I have to say it is my favorite plate material so far.  Really nice sound and feel.  You get the acoustics of plastic with the feel of something more solid like aluminum.  Cool stuff.  Of course, if you want a heavier board with more dampened acoustics, you should probably buy a brass plate.
:)

Offline beekey

  • Posts: 159
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #61 on: Mon, 31 December 2018, 11:19:58 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk

Yes, now the hardest part. The Choice of Color. :)

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #62 on: Mon, 31 December 2018, 12:21:00 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk

Yes, now the hardest part. The Choice of Color. :)

JTK Toxic with Black!
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline SlamMakanen

  • Posts: 26
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #63 on: Mon, 31 December 2018, 12:21:31 »
Need to make a slight correction on my username on the order sheet. What's the best way to do that our does it matter?


Sent from my iPhone using Tapatalk

Offline mkarlsson

  • Posts: 272
  • Location: Spain
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #64 on: Mon, 31 December 2018, 12:24:51 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk

Yes, now the hardest part. The Choice of Color. :)

Yeah, I went for black top and bottom with red + extra brass

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #65 on: Mon, 31 December 2018, 17:04:51 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk

Yes, now the hardest part. The Choice of Color. :)

Yeah, I went for black top and bottom with red + extra brass

Black Top + Red bottom + GMK Red Samurai my favorite combo
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline mechmode

  • Posts: 2
  • Location: Los Angeles, CA
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #66 on: Mon, 31 December 2018, 19:53:36 »
I put in two orders a few days ago and have not received any invoice. Also hoping to add a brass plate as well.

Offline AIRPOTTER

  • Thread Starter
  • Posts: 275
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #67 on: Mon, 31 December 2018, 21:22:11 »
I put in two orders a few days ago and have not received any invoice. Also hoping to add a brass plate as well.
Well, I keep sending out 8-10 invoices every day.
Can you pm me your ID or Email?
 I'll  adding some extra in your invoice.
INS:https://www.instagram.com/graystudio01/
discord:https://discord.gg/ckeXNRr
Reddit:Graystudio
imgur:graystudio01
slack:graystudio.slack.com

Offline mkarlsson

  • Posts: 272
  • Location: Spain
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #68 on: Mon, 31 December 2018, 21:28:08 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 splitting.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.
That's great news! Thanks a lot for that. Now I don't have an excuse to not join

Enviado desde mi Lenovo TB-8504F mediante Tapatalk

Yes, now the hardest part. The Choice of Color. :)

Yeah, I went for black top and bottom with red + extra brass

Black Top + Red bottom + GMK Red Samurai my favorite combo

Good one. Maybe gmk jamůn is also nice... weíll see...

Offline razor_blade

  • Posts: 88
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #69 on: Mon, 31 December 2018, 23:26:58 »
Joined yesterday but I haven't received an invoice yet either. I assume there are loads of them, so I'll wait patiently. Thanks again for this GB. It looks amazing.

Offline PotatoTM

  • Posts: 150
  • Location: ON, Canada
  • ...
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #70 on: Mon, 31 December 2018, 23:47:16 »

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #71 on: Tue, 01 January 2019, 00:04:13 »
Joined yesterday but I haven't received an invoice yet either. I assume there are loads of them, so I'll wait patiently. Thanks again for this GB. It looks amazing.

Private GB pricing :)
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline Oni74

  • Posts: 40
  • Location: New York, NY
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #72 on: Tue, 01 January 2019, 00:10:01 »
Just joined. Looking forward to building this board!

Offline Zyrophr

  • Posts: 4
  • Location: Paris, France
    • zyrophr.moe
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #73 on: Tue, 01 January 2019, 09:00:05 »
Just joined too!
First kit ever, for my first build ever.

Going to need some tools!


Can't wait!


Edit : What is the purpose of the top led strip?
« Last Edit: Tue, 01 January 2019, 09:21:51 by Zyrophr »

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #74 on: Tue, 01 January 2019, 09:56:53 »
Just joined too!
First kit ever, for my first build ever.

Going to need some tools!


Can't wait!


Edit : What is the purpose of the top led strip?

Led strip is just for visual effects I think

Now you need to a Hakko soldering station soon ;)
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline Poesjuh

  • Posts: 277
  • Location: Netherlands - N-H
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #75 on: Tue, 01 January 2019, 12:06:41 »
Any pictures with cherry profile that are on it yet?


Sent from my iPhone using Tapatalk

Offline rk74051

  • Posts: 1
  • Location: Incheon, South Korea
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #76 on: Tue, 01 January 2019, 12:48:50 »
Are there any extra rounds planned in future?
« Last Edit: Tue, 01 January 2019, 12:54:27 by rk74051 »

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #77 on: Tue, 01 January 2019, 13:07:46 »
Are there any extra rounds planned in future?

Perhaps, but I suspect if there is going to be one it wonít be this private GB pricing. You can check with Potter in the discord
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Online Ensaum

  • Posts: 25
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #78 on: Tue, 01 January 2019, 15:12:24 »
I'm going to get this for my SA symbiosis build. Do ya'll think grey or black would look better? I'm kind of leaning towards grey right now.

Edit: Just realized I can do 2 tone. Grey top and black bottom it is then ;D
« Last Edit: Tue, 01 January 2019, 15:15:19 by Ensaum »

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #79 on: Tue, 01 January 2019, 16:56:46 »
I'm going to get this for my SA symbiosis build. Do ya'll think grey or black would look better? I'm kind of leaning towards grey right now.

Edit: Just realized I can do 2 tone. Grey top and black bottom it is then ;D

I agree  Symbiosis will work very well with Gray top. An amazing SA set!
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline happycamper87

  • Posts: 32
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #80 on: Tue, 01 January 2019, 22:47:26 »
Just put in my order for a grey set. Hoping it pairs well with the incoming JTK Hyperfuse. Fingers crossed? Haha

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #81 on: Wed, 02 January 2019, 01:09:49 »
Just put in my order for a grey set. Hoping it pairs well with the incoming JTK Hyperfuse. Fingers crossed? Haha

Hyperfuse was sort of white? Gray will go well with a set like GMK modern dolch for sure I think
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline Poesjuh

  • Posts: 277
  • Location: Netherlands - N-H
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #82 on: Wed, 02 January 2019, 03:40:25 »
Afaik JTK HF is like the original HF right, not Origins? I have Origins on a grey keyboard and that looks very good, so I'm sure you'll be fine :)
When in doubt; go silver.

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #83 on: Wed, 02 January 2019, 15:01:53 »
Afaik JTK HF is like the original HF right, not Origins? I have Origins on a grey keyboard and that looks very good, so I'm sure you'll be fine :)
When in doubt; go silver.

Just to add that Potter said the silver on Space65 will be a bit matte and whitish
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline koduh

  • Posts: 93
  • Location: Arizona
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #84 on: Wed, 02 January 2019, 21:56:22 »
So I think I screwed up my order form and added a second CF plate... I thought the question was asking if we want alu vs brass vs cf. Can I change that somehow?

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #85 on: Wed, 02 January 2019, 23:49:45 »
So I think I screwed up my order form and added a second CF plate... I thought the question was asking if we want alu vs brass vs cf. Can I change that somehow?

I guess either pm potter in discord or just send in a new form and note discarding the old one.

He hasnít invoices you yet right?
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Online factoryofidols

  • Posts: 11
  • Location: TX
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #86 on: Thu, 03 January 2019, 00:22:58 »
I am in for sure, but would love to see what gray top with dark blue bottom would look like.

Offline FSund

  • Posts: 120
  • Location: Norway
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #87 on: Thu, 03 January 2019, 04:55:02 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 spli.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.

Amazing work, and thanks for clarifying. I'm definitely in then.

Is it possible to order multiple boards, to save on shipping/import fees?

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #88 on: Thu, 03 January 2019, 08:49:58 »
Ok great, the pcb supports it. I guess it will but can you confirm that the plate will also support it?

If this image shows the final plate, I don't think the plate supports it: https://i.imgur.com/iH2L6IA.jpg
The hole needs to be a bit bigger on the right hand side, like this plate: https://imgur.com/a/6UVqnw2 (image borrowed from here)

But this is just a minor edit of the plate, so I hope it might be possible to add this change.

EDIT: Here's an image of a sample carbon fiber plate I found in the album, which seems to have the same cutout for the left shift (which doesn't support ISO shift): https://i.imgur.com/okCKcro.jpg
Sorry for that, its my mistake.
And I slightly modify the left shift position of the plate,so that can support 1.25+1 spli.

Show Image

This is my updated rendering.
The plate in this figure is compatible with splitting left shift.
This is also the final version of the plate.

Finally, thank you very much for your careful observation.

Amazing work, and thanks for clarifying. I'm definitely in then.

Is it possible to order multiple boards, to save on shipping/import fees?

Just send in another order form or pm Potter :)
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline tyson522

  • Posts: 53
  • Location: Texas
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #89 on: Thu, 03 January 2019, 09:43:01 »
Just joined the GB! I can't wait for this baby! It's going to be amazing!
(Reserved for Noxary 268.2 Polycarb) | (Reserved for Persona 5 Custom)| Pearl | (Reserved for Kyuu) | (Reserved for APX) | 60XT | TX-CP | QXP | Noxary 268.1 | Noxary X60 | KBD75 | Scarlet Bandana | Kira60 | Orange Alps Custom | VE.A | NightFox | Rorschach | Levɘ˩ | Mechmini2 | NovaTouch | Tada68 | K-Type | HHKB | Pok3r | Magicforce68

Offline rdg

  • Posts: 7
  • Location: California
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #90 on: Thu, 03 January 2019, 14:55:35 »
please look at these two pictures. I did a simple test to split space【2.25-1.25-2.75】
This is with switch;
Show Image

This is with keycap.
Show Image

I hope I can help you out.

Hi potter. I think this is true from the picture but does it only support 2.25/1.25/2.75 split space? And not support 2.75/1.25/2.25 space. I thought from IC you said it will support both, but from picture it only looks like one style. I am hoping for 2.75/1.25 style. Can you confirm - thank you.

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #91 on: Thu, 03 January 2019, 21:11:31 »
please look at these two pictures. I did a simple test to split space【2.25-1.25-2.75】
This is with switch;
Show Image

This is with keycap.
Show Image

I hope I can help you out.

Hi potter. I think this is true from the picture but does it only support 2.25/1.25/2.75 split space? And not support 2.75/1.25/2.25 space. I thought from IC you said it will support both, but from picture it only looks like one style. I am hoping for 2.75/1.25 style. Can you confirm - thank you.

It appears only 2.25/1.25/2.75 is supported :(
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Online Ensaum

  • Posts: 25
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #92 on: Thu, 03 January 2019, 23:42:55 »
I agree  Symbiosis will work very well with Gray top. An amazing SA set!

Actually, I may do silver and black because silver looks great with Space Cadet from the pictures I've found.

I could also better use silver with Hyperfuse. I wish I could just buy two top cases.
« Last Edit: Fri, 04 January 2019, 08:23:57 by Ensaum »

Offline oldcat

  • Posts: 890
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #93 on: Fri, 04 January 2019, 00:43:41 »
For those interested in possible mil max sockets, itís not guaranteed it will work but here is some info:

Clearance between switch pin and bottom case: 0.8mm
Switch pin through hole diameter: 1.5mm
$ Instagram: https://www.instagram.com/oldcat87/
$ ALF Studio Discord: https://discord.gg/NHYnp8g
$ Gray Studio Discord: https://discord.gg/s99eys2

Offline peteAllen

  • Posts: 1
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #94 on: Fri, 04 January 2019, 07:04:00 »
Hello. Is there any chance we can buy extra top plates? Particularly because all the colors are great. My ideal would probably be a base kit in silver, with extra top plates in blue & black

Online pcire

  • Posts: 10
  • Location: SF
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #95 on: Fri, 04 January 2019, 08:28:46 »
Hello. Is there any chance we can buy extra top plates? Particularly because all the colors are great. My ideal would probably be a base kit in silver, with extra top plates in blue & black

You can in the order form.

I read your question wrong. Thatíd be cool if you could order extras.
« Last Edit: Fri, 04 January 2019, 08:33:37 by pcire »

Offline cijanzen

  • Posts: 205
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #96 on: Fri, 04 January 2019, 08:32:03 »
Hello. Is there any chance we can buy extra top plates? Particularly because all the colors are great. My ideal would probably be a base kit in silver, with extra top plates in blue & black

You can in the order form.

Not that I can see. Extra badge, plate, and PCB but no extra top case.

Offline walie

  • Posts: 3
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #97 on: Fri, 04 January 2019, 08:41:15 »
For those interested in possible mil max sockets, itís not guaranteed it will work but here is some info:

Clearance between switch pin and bottom case: 0.8mm
Switch pin through hole diameter: 1.5mm

I wonder if that's enough to fit 7305 sockets?

Offline ConfuseBill

  • Posts: 15
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #98 on: Fri, 04 January 2019, 10:00:09 »
Hi,

Is this a Top Cover mount PCB Plate? Is it enough screw holes on the Plate?
Cause from what i see, the screw holes are only located on the left, right and bottom of the Plate.
Will the number row have enough support, since there is no screws to hold on to.

I love to join, but need to know if the keyboard will hold strong, without flimsy feel when bottom out.

Thanks.

Online Ensaum

  • Posts: 25
Re: [GB] SPACE65 | 65% Custom Keyboard
« Reply #99 on: Fri, 04 January 2019, 10:37:59 »
Hi,

Is this a Top Cover mount PCB Plate? Is it enough screw holes on the Plate?
Cause from what i see, the screw holes are only located on the left, right and bottom of the Plate.
Will the number row have enough support, since there is no screws to hold on to.

I love to join, but need to know if the keyboard will hold strong, without flimsy feel when bottom out.

Thanks.

Two on the sides and 3 along the bottom, but none on the top. Carbon fiber is very strong though, so this should be plenty of support. I wouldn't worry about it being flimsy.

« Last Edit: Sat, 05 January 2019, 01:49:41 by Ensaum »